79 modeli
19 Mar 25 - Added a new looped version that's much sturdier than previous models. Also changed the latch so the hinge was coaxial to the fillet. Overall, a more refined model than any of the previous iterations. 8 May 24 - Added beefy…
This is a remix of "Waveshare display (v1/v2) with a PiSugar 1200mAh battery and a carabiner loop" to support the PiSugar2 1200mAh (switched USB charging port/button, and added a slot for the power switch). I made the case and lid a…
Standard pwnagotchi case Build your own pwnagotchi!!! instructions here: https://youtu.be/Gw4yCRKLn3Y Checkout case overview video here: https://youtu.be/KD7heRy_vDg Checkout the how Pwnagotchi build series playlist on my channel page:…
My case for slim edition of Pwnagotchi.
The cases in the original only had versions for the Pi Sugar v1. The V2 has both a switch and a button. I rejigged the case based on both this and the Pi Sugar cases (purely used to get the hole locations correct) and updated the buttons…
Features: USB C charging port 2 buttons (need tolerance check when printing) side hook perfect fit for the display perfect fit for the battery + the magnet mount to the Pisugar 3 the lid is a tight fit but it has 2 holes for easy removal…
I designed this case for the Geekworm X306 UPS shield. It provides constant power via a 18650 Li-Ion battery. You can plug and unplug the USB-C port on the back to charge the battery as needed, without interrupting the operation of the…
(⌐■_■) if you have the combination of an pwnagotchi based on the raspberry pi zero with the waveshare display, have an RTC installed and the UPS-Lite you want this case! i included STP and STL-Files let me know what you think!…
I designed my Pwnagotchi case around my build: Raspberry Pi 0 W Waveshare v2 with "slim-agotchi" low profile mod PiSugar power pack with 1200mAh battery It's a snug fit that exposes the USB ports while the cover is dovetailed and slides…
I created this case to encorporate the Waveshare V4 Epaper display, together with the UPS Lite V1.2/V1.3 and the Pi Zero or Zero 2w. The Dimensions of the case is WxDxH 75x25x36mm. It is smaller in all dimensions than a flipper zero with…
To have a good alignment the magnets need to be removed from the battery and the pisugar2. I added a version without pisugar and battery.
Original: https://www.thingiverse.com/thing:3920904 Added slots for straps to carry it with a power bank attached and I also made the walls a bit thicker.
Remix to use the waveshare 2.13inch E-Ink display HAT. Print in place, not supports are needed.
Alternative Top Case for "Pwnagotchi case for Waveshare and Pi Sugar v2" You can find the Case and Buttons here: https://www.thingiverse.com/thing:4551538
This a remix of PantsManUK's remix. The original carabiner loop was a bit choppy when trying to send off to 3D Printing Services like PCBWay, so I fixed that. Also, the NEW_LID file is actually done by formlessform @formlessform_1988521…
If you use a UPS-Lite and a Waveshare 2.13" e-Paper pHAT with your Pwnagotchi this is the case for you
Be careful, this case has tight tolerances! (Remove the SD card before putting your pwnagotchi in!) You will have to slightly flex the side where the micro usb ports are to make your pwnagotchi fit. If you have any issues or need help…
Here is a Pwnagotchi case i made. It's to hold a waveshare V3 + PiSugar 2 + raspberry zero 1.
A super handy pwnagotchi - for your journeys in the city :D
Pwnagotchi is an A2C-based “AI” powered by bettercap and running on a Raspberry Pi Zero W that learns from its surrounding WiFi environment site of full project: https://pwnagotchi.ai this is a pwnagotchi case with protective cover for…
Check out my newest Pwnagotchi case here This is a remix of the case for the pwnagotchi by soul_Stz. I adjusted the side of the case so that the WaveShare v4 can be inserted correctly with a Raspberry Pi Zero 2. I had the problem that the…
This design is a case for a Pwnagotchi build using: Raspberry Pi Zero 2WH Waveshare UPC HAT (C) Waveshare V4 2.13" E-ink Display HAT a MOLLE Strap like this one 8x 2.5x3.5mm screws It is designed to fit a non-slim variant of Pwnagotchi…
One of the best pwnagotchi case - edited to be openable in any program as I had similar problem mentioned in comments of original file. All credits to the original creator ! Thicc Dual Loop version (without letters) print as it is - in…
A foldable case for pwntagotchi that uses just the screws from the hat. Printed in PETG 2. mm layers standart settings. Show off your printbed design on allmost all sides! There ale more variants of the bottom part, you can use 4…
Pwnagotchi case with antenna slot and ring for a carabiner / snap hook Pwnagotchi project: https://pwnagotchi.ai/ Used parts besides the basic pwnagotchi setup: U.FL RF Port SMD (to connect an antenna to the pi zero) wifi Antenna SMA
This is a case for a Pwnagotchi that uses a Raspberry Pi Zero, PiSugar S battery, and Waveshare V4 E-Ink screen. Note: Once you put the SD Card in it is very hard to remove.
Using Ya Ikou's Pwn-In-Place case as inspiration, I designed a new variant from scratch. Built Specifically for this setup: Raspberry Pi Zero 2WH PiSugar3 2.13" E-Ink Display HAT V4 My perceived improvements over the original: Made loop…
Tested with a Pi Zero 2WH And Waveshare 2.13 inch V4 eink screen (supports Pi Zero WH, Waveshare v3 as well) Check out my Pwnagotchi guide and plugins too How to Use: First, remove the microSD card from the Pi Zero, then attach the pi…
To print this I used eSun PLA+ on my Ender 3 Pro. These are the settings I used: 0.2mm resolution 20% infill Normal supports everywhere I recommend printing the body of the case with the USB-A hole facing up. The top cover takes a bit of…
This remix is based on the fantastic Pwnagotchi case for Waveshare and Pi Sugar v2 by MrDrem This case is designed to work with: Raspberry Pi Zero 1/2 Waveshare V2/3/4 Pisugar3 I hope this variation is helpful to others in the community!…
Pwnagotchi case with or without external antenna 4xM3*20mm 4xM3nuts 4xtiny screws that came with the waveshare display
Case for Pwnagotchi - slimagotchi mode. The model should be placed vertically when printing. The side of the SD card on the bed. Everything is without supports. I used a 9mm spacer between the UPS and the Raspberry Pi. There are two…
This is a heavy remix of a case that I found on Thingiverse. Added a lot more holes and accesses for Pisugar 3 new buttons and LEDs, and Waveshare 4 e-ink panel. Also changed some tolerances and added some reliefs so the e-ink ribbon…
I printed it in .2mm layer height without supports, it went well on my printer. The model has a hole on the back to accomodate the heatsink.
This is a case for a pwnagotchi made with a Raspberry Pi Zero/2W or similar SBC, a Waveshare 2.13" Touch ePaper, a Waveshare UPS-HAT, and an Alinan GT-U7 GPS Module and antenna. The GPS module goes underneath the UPS-HAT, and the GPS…
Check out my newest Pwnagotchi case here Very compact 3D printed case designed to works with: Raspberry Pi Zero WaveShare 2.13inch E-Ink Display HAT,250x122 Pixel Black 550 paracord (if using loop) Supports 3D printed Pico mounting…
Pwnagotchi case with molle clip on the back. This model has support for the clip included.
Made as a remix of Cyberpunk Pwnagotchi Case by kat_stuck_in_a_tree designed to accommodate: PiSugar S Battery, 5ghz USB antenna, RGB function indicator, DS3231 Hardware clock. Design is still a work and progress, I have not yet assembled…
UPDATE added new improved side holes for the USB ports Two versions one that is solid, and another that has access to the USB ports, 2 ports for Raspberry Pi and 1 port for the PiSugar. Also two different lids one with ventilation and one…
Original model requires shorter spacers for the ups lite battery pack. In my pwnagotchi I am unable to install the shorter spacers as it causes the pi board to press on the battery and is very dangerous. There is heat etc. and the battery…
The original lid is about 1.5mm too deep (front to back), so I've cut that much out of the middle of it and merged the resulting parts. It now fits perfectly.
Slimagotchi case: Fits Pi 0W ( no header flush pins) with waveshare 2.13 screen Learn how to build a "slim" pwnagotchi here: https://youtu.be/rlTzREaGmII Checkout case overview video here: https://youtu.be/KD7heRy_vDg Checkout the how…
This is old (2018~2021) - I created this for the different pwnagotchi I gifted friends. They often times ran quite hot, which directly affected the performance. Rasberry Zero - Waveshare 2.13inch E-Paper Display HAT V4 Version 250x122…
Check out my newest Pwnagotchi case here Fourteen versions of the case are included: Inky display. Inky display with a carabiner loop. Inky display slimagotchi mod. Inky display slimagotchi mod with a carabiner loop. Waveshare display…
Pwnagotchi Case with WeAct 2.9" ePaper Display "Sources" of the Model can be found on OnShape: https://cad.onshape.com/documents/172fee915b4cc3dc319ceb2f/w/33094c145713f3fa30397bbe/e/763a9c2fd96bd14b04fed502
The fuzzy skin settings for my print is: Fuzzy skin thickness: 0.2 Fuzzy skin point distance: 0.2
Case for pwnagotchi that can store on this order: Screen 2.13" e-Paper Display Hat V2 with slimagotchi mod (remove connector) Raspberry pi Zero WH UPS Lite V1.2 GPS Module GY-NEO8MV2 THe GPS module go on the back of the case and an open…
This is my version of the case for pwnagotchi. Waveshare V4 e-Ink display Raspberry Pi Zero W PiSugar 3 PLA with 0.28mm layer height. No supports. Use M2.5 screws 10mm or longer. Tolerances are pretty tight, but mine fits like a glove…
I wanted to have a frame between the E-Ink Display Hat and the Raspberry Pi for my pwnagotchi. I also use the PiSugar battery pack so I needed a version that would sit down over the screw heads. So I offer two versions: one with the pegs…
Same Case, but with a base to stand it upright and it will not turn off or on!
I designed a case for the pwnagotchi that uses a 2.13" e ink screen a raspberry pi zero w 2 a powerbank board and battery that all fits in a iPhone 13 case. Full info can be found at my blog post below Blog post -…
Small Notice I recommend adding some glue on the sides of bottom snap covers to keep the lid attached better to the main case. NEW AMS OPTION ON MAKERWORLD: https://makerworld.com/en/models/494603#profileId-408615 Components for…
This is a remix of Jeremy702's great non-low profile case. The main changes are to move the Micro SD-Card slot from one end to the other and to add an opening so you can access the ON/OFF switch on the PiSugar2 power board. Print Settings…
Removed clip and added some holes in the back for air flow.
To install board may need to be tipped so the HDMI connector is inserted first. Clips may be tight. Print parts standing for best clip strength. Designed and printed at 3 wall 15% infill. Tested in PLA and PETG
Case includes precise cutouts for USBs and SD card, as well as a mounting loop for attachment to bags or keyrings. 📦Hardware used in this build: 🧠 Raspberry Pi Zero WH ⏰ RTC Module : RTC Pi DS1307 - Real Time Clock Shield 🔋 Power…
This is a flat assembly of the pwnagotchie. Requirements 4x m3 screws 6-10 mm raspberry pi zero pisugar v2 wave share epaper Assembly The 2.54 mm spacer goes on the GPIO pinheaded of the raspberry pi to get the correct distance. The…
Check out my newest Pwnagotchi case here The case will fit raspberry zero 2w and the Waveshare 2.13 inch eInk HAT https://www.thingiverse.com/thing:4075616 and https://www.thingiverse.com/thing:6410181 Print Settings Printer brand:…
Pwnagotchi Case: Rasberry Pi 256gig sd card Geekworm Rasberry Pi Zero 2 18650 UPS Expansion Board X306 & Usb Hub Heatsi
A Backpack / Strap Mounting bracket / Holder for Pwnagotchi and Pi Zero Pico Case
Wanted to make a case for my pwnagotchi build that has magnets. Magnets to use are Harbor Freight Small Earth Magnets.
Custom holder for a Pwnagotchi - designed for the Gridfinity modular storage system. Based on this Case: https://makerworld.com/en/models/202773#profileId-223140 It features precise dimensions to integrate with Gridfinity setups. The case…
A Remix of the Swiper Pwnagotchi case from syntask at Thingiverse. The added SD-Adapter is press-fit, just slide it over the SD from one side. See the Model origin section below for all the changes i made. Works with this components:…
A simple Pwnagotchi case designed for setups without a battery pack. The HDMI port remains fully exposed for easier setup, debugging, and external display access. What I used: Raspberry Pi zero WH Waveshare 2.13 Zoll E-Paper HAT+…
I fell victim to not removing the SD card, BUT THE BOARD SURVIVED. Also, my micro USB bent, and I don't like how the HDMI scratches the case, plus I added a “window” so that the LED is visible on dark filaments. And then there's the…
I wanted to mount my Pwnagotchi on my EDC Bag, which uses MOLLE loops. I was unable to find a suitable option online so Designed one. You Will absolutely need to resize it based on printer and material. This will fit any Standard Pisugar…
The Backplate ist for the case made by PicoProject on Thingiverse: https://www.thingiverse.com/thing:4511022
Its a case for the pwnagotchi thats themed with rebecca from edgerunners It also includes a mount to attach to bags or other stuff! Pairable with the powerbank holder Is based on and oriented around the case made by PICO
This case was created for the Zero 2 W version of the Raspberry Pi with Waveshare V4 - NO slim mod. Plese keep in mind, that there can be errors. (The hole for GPS antenna isn't included in the model)
Slightly different sized lid from the original and other remix.
USE SUPPORTS! Preferrably tree type supports
Printed with PLA, the holes might not be aligned perfectly because the goal here was not making an "all-in-one" product, however, its still better than having no case at all because this will protect your device from dust and anything…
Modified pi body for use with my piReader program. Added button and switch for easier interaction and removed unneeded ports for a minimal case design. Converts pwnagotchi to a little ereader with the pisugar button for interaction with…
I fell victim to not removing the SD card, BUT THE BOARD SURVIVED. Also, my micro USB bent, and I don't like how the HDMI scratches the case, plus I added a “window” so that the LED is visible on dark filaments. And then there's the…
A Remix of the Swiper Pwnagotchi case from syntask at Thingiverse. The added SD-Adapter is press-fit, just slide it over the SD from one side. See the Model origin section below for all the changes i made. Works with this components:…
This is old (2018~2021) - I created this for the different pwnagotchi I gifted friends. They often times ran quite hot, which directly affected the performance. Rasberry Zero - Waveshare 2.13inch E-Paper Display HAT V4 Version 250x122…
Remix of the Pwnagotchi Case by PantsManUK. The lid didnt snap in place & was loose, I added 0.2mm so it snaps in place and stays put now.
