106 modeli
Bullet quiver that holds two extra 308 cartridges to the side of your rifle. I designed mine to fit the side of my KRG Bravo chassis screw locations, however these will fit standard m-lok slots using t-nuts similar to what can be…
Two versions with 2 or 3 slots : -vertical -horizontal
Holds up to 6 arrows of any size. I printed with 0.3mm layer height and only used supports shown in the image. I printed with PETG but in reality, most materials will be fine. Just make sure you align the part so the holes where the…
Hello everyone, I was tired of constantly having the little bolts flying around somewhere, so I designed a small quiver for the popular Alligator 2 pistol crossbow. Initially, the bolts fit quite tightly, but there's a protrusion in the…
By request: Archery Pocket Quiver with Hoyt Logo Logo from here: https://www.thingiverse.com/thing:3033674 Other designs: Martin Archery: https://www.printables.com/model/431226-archery-pocket-quiver-with-martin-archery-logo PSE:…
By request: Archery Pocket Quiver with Mathews Logo. 8 mm and 11 mm is the diameter of the holes for arrows. For outdoor/3D you may use thin arrows so take 8 mm, for Indoor arrows or thick arrows take 11 mm. Other designs: Martin Archery:…
Bullet quiver that holds two extra 30-30 Winchester cartridges to the side of your rifle. These will fit standard m-lok slots using t-nuts similar to what can be purchased here:…
This is my entry for the finger toys flash contest. This design is based on a Bow and Arrow. I have included other accessories like a target and a quiver. Before I start these instructions I want to thank you guys for waiting, I have been…
A simple quiver to hold 3 arrows on the bow. Fits arrows with diameter from 5.4mm to 6mm. To be mounted on the recurve bow, most have two existing threaded holes 34mm apart. Printed in PETG as I have the bow often in the car and under…
A fantasy-like archery quiver with just two arrows left! Designed as a small giveaway to be printed quickly without supports (although an alternate STL is provided with minimal support for the upper loop if necessary). I ended up adding a…
Join to Unlock All STL Files FOR FREE: https://starforgekits.com/ StarForge Kits is the largest producer of STL files for 3D printing. We specialize in true-to-scale models, especially in 28mm. All models are correctly scaled and easy to…
se puede imprimir completamente hueco si quieres ahorrar filamento, tiene unos agujeritos abajo para que pueda salir el agua en caso de que se moje. It can be printed completely hollow if you want to save filament, it has some holes at…
Credit to Zanzibar_T_Cricket on Reddit for the awesome name. Updated June 8, 2025: Based on some feedback from @JammerX19 , I've added some labels to indicate where the driven element for each band should be located. For 2 meters, this…
This was designed for the Monarch Takedown Recurve Bow, but if your bow has an attachment point with holes spaced 34 mm apart, it should also work just fine. You will need (2) #10-24 x 1/2in screws/bolts. IMPORTANT: Printing the part in…
English: A small and neat Pocket-Quiver I designed for my backpocket. Scale as you need it. At 100% the holes are 8.25mm wide and tilted from the inner to the outer holes by 1 degree, 1,5 degrees and 2 degrees, so the feathers/vanes do…
I did this archery pocket quiver mainly to learn to use Fusion 360. I am a compound archer and PSE fanboy, but did it also without any logo. Printed with Palette 2 Pro and works great! TK-color is the one with the skull. PSE-color ist the…
[EN] This is the Tactical arrow quiver from Steambow for the AR-6 Stinger II. The dimensions are taken from the original quiver. I have left out the Steambow lettering for individualisation. [DE] Das ist der Tactical arrow quiver von…
Created this plugin for my Neet-Quiver. The arrows will make less noise while walking from the target back to your bow and stay in place. Only for thin arrows up to 7-8mm. The fletches will be saved. Pipe diameter 32mm.
[Deu] #Info Brauchte für meine Knipex Cobra XS eine Halterung/Aufbewahrung, weil sie mit ihrer scharfen Kante vorne schnell Löcher in meine Arbeitshosen zaubert. Nutze das ganze jetzt seit über einem Monat und habe mich daran gewöhnt.…
Join to Unlock All STL Files FOR FREE: https://starforgekits.com/ StarForge Kits is the largest producer of STL files for 3D printing. We specialize in true-to-scale models, especially in 28mm. All models are correctly scaled and easy to…
Кивер на блочный лук под 3 стрелы диаметром 7.6 мм. Кивер крепится к луку на быстросъёме. Собирается сам кивер на остатках поломанных стрел Ф7.6мм. Для охоты вряд-ли подойдёт, т.к. шумно извлекаются и вставляются стрелы. Части замка…
Easily store, transport and use your paint brushes This product is model to serve as a convenient solution for artists or painters to manage their paintbrushes effectively. It addresses three main purposes: storage, transportation, and…
Description: This is a Batmobile (Tumbler design)-inspired back quiver. Although it's designed as a single entity, it's recommended to slice it into smaller printable pieces (you can use PrusaSlicer for that). To reduce the rattle of the…
Simple standing quiver for 15 standard 6.5'' bolts with practice tips, as used in an Alligator 2 or other pistol crossbows. Loose fit for easy loading/reloading. Can also be used for other bolts, if scaled accordingly. Should be printed…
Lost my quiver guard for my big bore .625 blowgun, so I made a replacement that entirely covers the "razor blade" type dart. Printed in Petg, mine was quite snug. If fitment isn't sufficient, I recommend adjusting the size when slicing…
I think quivers look tacticool on real steel, so I decided to add one to the SLAB Skeleton stock, the most tacticool stock. I designed the quiver portion myself and used the cheek rest from the Skeleton stock for mounting. I included a…
I am sure the Magnus version works just fine but I couldn't find any in stock and decided to just make my own. I used a piece of scrap from a Goldtip Hunter shaft that measured 7.6-7.7mm in diameter and glued it in the end. That way it…
A friend of mine recently bought a Gillo GT 21 riser and was looking for an bowquiver so I designed one. It should fit every Gillo GT-riser with this limbpocket-design and was tested successfully on a GT21 and a GT25. I designed it so it…
300BLK 2 Round Quiver This is a simple 2 round quiver that I made for hunting with a single round magazine sled. I used PETG with 100% concentric infill standing on end using “Tree” supports
Join to Unlock All STL Files FOR FREE: https://starforgekits.com/ StarForge Kits is the largest producer of STL files for 3D printing. We specialize in true-to-scale models, especially in 28mm. All models are correctly scaled and easy to…
My neighbor asked if I could design and print a replacement attachment for his Barnett Crossbow quiver. He said he, his wife and brother all had the same model and the quiver attachment broke on all three and the manufacturer would not…
Pocket Quiver that holds 8 arrows. The diameter on the slots is 9.75mm which is snug on the G5 BMP practice broadhead that I sometimes use and a little loose on the regular field tips. It's also a little unwieldy and I'm not sure I'd want…
This pistol crossbow quiver system is comprised of two picatinny rail quivers, and a triple picatinny rail adapter, which allows both quivers to be mounted horizontally, in addition to a bottom grip. Each quiver securely holds six…
Archery pocket quiver with Spiderbows Logo. I printed this time with my Resin printer, filled the logo with colored resin, sanded up to 2000 grit and then sprayed some layers of 2k clear coat to get it as transparent as possible. Please…
Print with the hole facing the build plate and you should be able to print in place.
A hanger for the tightspot 5 arrow quiver for hunting. I just used some spare zing-it rope I had laying around, but paracord or really any other small diameter rope should work. A rope that way there is less potential for noise with…
The components are designed with a very close fit to standard 1 ½" ABS drainage pipe. Some sanding required. In my example I printed the components in ASA, used plumbing abs glue to attach them. I have only actually printed and tried the…
Designed for a Cartel Dynamic 501 Quiver but will work with any quiver that has the same size tubes. Print all parts as is, The top part will need supports I used a soft TPE for everything, except, one of the top parts using TPU instead…
3d printed Caps are connected with glue and small lengths of filament. The body is made from a standard size paper tube used to ship posters or long items. The paper tube is squished into the oval shape and covered in thin fabric. I used…
Insert into a Ragim brand belt quiver(http://www.ragim.org/product/accessories/quiver-2t) to prevent arrow rattling. The quiver this is intended for has 2 tubes, one is by about 2 cm longer. The middle part has to be printed twice to fit…
A flexible arrow-quiver for my Fjällräven Singi Stubben Chairpack.
Archery Pocket Quiver with Flagg of Switzerland on it. Other designs: Martin Archery: https://www.printables.com/model/431226-archery-pocket-quiver-with-martin-archery-logo PSE:…
The original model was very nice and low profile, which I love – but I have a whisker biscuit on my bow, so that prevents use of two of the arrow slots - and on my riser (PSE Pro Max), the backs of my fingers make contact with the arrows,…
Something to hold you arrows during practice or competitions. Currently only suitable for 16mm and 14mm darts. To create quivers for 12mm darts, scale X and Y to 90%, for 10mm to 80% (assuming your darts are all the same length,…
Archery Pocket Quiver with Bowtech Logo for arrows up to 11mm diameter Other designs: Martin Archery: https://www.printables.com/model/431226-archery-pocket-quiver-with-martin-archery-logo PSE:…
Needed something to store my Excalibur crossbow quivers when not on the crossbow so I made a small hanger that they slide into and can be hung on a wall
This hold 6 Easton 400 FMJ arrows. The diameter of those arrows are 0.263". This should fit your standard cheapie quick detachable quiver on the market. I included a picture of the old one vs the new. Print it in TPU.
It is a arrow holder designed for the outdoors, you will need a pipe for the center for the arrows, I added this part because most printers cant print that high. The main reason its designed for outdoor use is because you can add weight…
I have been working on my modelling skills using AI. I have printed all models I upload and then paint them. I printed this one in ASA seeing as it will reside outside in the landscaping.
Magnetic antenna quiver for HT antennas. The magnets may be found here: https://www.amazon.com/dp/B07DGTT52D?ref=ppx_pop_mob_ap_share
I didn't have any spare arrow cutoffs to use ryhno00688's design. This adds the straight section instead of gluing in an arrow shaft. I also brought the tapered section on the top of the adapter down to allow this to sit as high as…
you can easily build your quiver. just use three Ø25 mm pipes, a string and a metal ring. you can find the clip to hang it on the trausers on my profile
Gürtel Köcher Scheibenreinigung, für Abzieher und Einwascher 35cm. Erstellt mit OpenSCAD. Das Modell ist in den Abmessungen frei konfigurierbar. Die einzelnen Elemente des Köcher sind als Module kreiert, diese können dann final am Ende…
Bottom mount for the filament slot of the carrot quiver buffer because I don't like the stock one since it makes removal really hard, with this it's really easy to remove and service if needed. requires support and its printed upside…
Flat quiver for Ø6mm arrows, LARP
Autodesk Fusion file is included so you can customize text. Recommend printing with enough perimeters and top / bottom layer to get a solid print. Helps to give it enough weight to be stable.
Upcycle your carton roles to get a toy quiver; Additional you need two empty carton roles, stripes of a tape and a shoelace Easy to print, no supports needed.
Scythe sharpeningstone quiver STEP file included Perimeters: 5 Infill: 25%, gyroid Supports: no
Sized for the Ryobi small cordless glue gun, but it should stick anywhere flat. The holes are to increase the engagement with the hot glue pool, make it stick to the surface better.
This is my modern take on a traditional bowyer and hunting item. The 3D Printed strap-on longbow quiver. Another pain point addressed by this model is the wearing out of quiver foam, by printing only side walls and not top an bottom, TPU…
Print wedge at 100% and be sure to clean up elephant foots to make sure everything fits together. I'm still having trouble with how to mount it to my bow, as it keeps twisting, but this design doesn't fix that.
Illustrating how to include a belt clip without relying on layer adhesion, as per this thread. Holds 8x 6.5mm diam arrows. - print auto-orientated, no supports required.
A simple to print insert for an Elevation Mettle Field Quiver, that helps sorting arrows and makes the quiver more silent if you print it in TPU. To connect the three elements you can use cut down arrowshafts (.144 inch) or 5.5mm rods. I…
Archery Pocket Quiver with Darton Logo for arrows up to 11mm diameter Other designs: Martin Archery: https://www.printables.com/model/431226-archery-pocket-quiver-with-martin-archery-logo PSE:…
Köcher für Thermometer mit 300 mm Länge und ca 9mm Durchmesser wie er z.B. bei der Filmentwicklung benutzt wird. Der Köcher hat innen 12 mm Durchmesser und ist zusammengeschraubt innen 310 mm lang. Durch den Vierkant an den Enden kann das…
Attaches aftermarket quiver to cable guard similar to PSE 2 piece quiver system. All you need to do is drill holes for the attachment screws. Setup to work with my VRSA Light quiver but should work with other aftermarket quivers.
Updated model with wider grips for the quiver and screw holes that match the cable guard.
Due to age the straps on my Big Tradition bow quiver started falling appart, so I created a replacement. The dimensions for the holes are like in the original part. I replaced the criss-cross pattern with a single rectangle to strengthen…
Protect your board's base when stacked for travel with other Quiver Connector and/or Ride Mode mounted boards. These quiver protectors are much more durable than the stock Karakoram foam quiver protectors. They are made from a durable…
Simple standing quiver for 15 standard 6.5'' bolts with practice tips, as used in an Alligator 2 or other pistol crossbows. Loose fit for easy loading/reloading. Can also be used for other bolts, if scaled accordingly. Should be printed…
English: A small and neat Pocket-Quiver I designed for my backpocket. Scale as you need it. At 100% the holes are 8.25mm wide and tilted from the inner to the outer holes by 1 degree, 1,5 degrees and 2 degrees, so the feathers/vanes do…
Print with the hole facing the build plate and you should be able to print in place.
Bolts: https://www.aliexpress.com/item/1005009225023838.html?spm=a2g0o.order_list.order_list_main.68.58671802aq6Crs Parts list: 1 x >30mm M5 Screw 1 x M5 Nut
Updated model with wider grips for the quiver and screw holes that match the cable guard.
Legolas – Buste Porte-Stylos License This file does not include a commercial license . If you wish to sell physical prints of this model , you can obtain a commercial license by joining my Patreon: 👉 https://www.patreon.com/c/JulienMairy…
Protect your board's base when stacked for travel with other Quiver Connector and/or Ride Mode mounted boards. These quiver protectors are much more durable than the stock Karakoram foam quiver protectors. They are made from a durable…
Using a 1.5" diameter ABS pipe at 16" length. Add a carabiner and paracord/rope to clip on a belt. It is a snug fit, but add glue to keep them attached.
An Archery Quiver that fits any standard arrow It will require an M6 X 5mm screw and a strap of 26mm in width and 4mm in
I wanted a guide to hold the drill and tap at 90 degrees when installing my quiver killers. The drill guide is taller so you can set the right depth. Also printed a Threader handle from here to use wit the tap tool WARNING: Do not use the…
This is an arrow stand that I designed for use when practicing archery. It's also handy to store arrows upright and conveniently.
My son wanted a quiver for his minifig that would hold a sword and bow as well. I used two existing models to create a unique piece that worked perfectly for him. I printed this in PET-G for durability. It might work in PLA, but I didn't…
I wasn't satisfied with how my bows rested on this ground quiver, so I made an adapter that slides on and balances my two sizes (54" and 66" risers). Print in PLA (or whatever) and secure with two TPU o-rings.…
Bolts: https://www.aliexpress.com/item/1005009225023838.html?spm=a2g0o.order_list.order_list_main.68.58671802aq6Crs Parts list: 1 x >30mm M5 Screw 1 x M5 Nut
Requires m5x12mm bolts and m5 nuts, fit is tight on the nuts so just hammer them in place.
Legolas – Buste Porte-Stylos License This file does not include a commercial license . If you wish to sell physical prints of this model , you can obtain a commercial license by joining my Patreon: 👉 https://www.patreon.com/c/JulienMairy…
-These inserts are ment to seperate the arrows in each compartment, and reduce the rattling. -Printed mine with Flexfill 98A since it requires the inserts to flex/bend a little. -They simply slide down on each segment and doesn't require…
This is a simple quiver I came up with to mount to the picatinny rail on the bottom of a mini crossbow
I have only printed the 6 arrow version. There are holes in the bottom that i used to glue pennies in for additional weight, this is probably unnecesary unless you are dealing with wind or uneven ground. Printed in PETG, 2 walls with 8%…
Wenn dir klappernde Pfeile beim Training oder Turnier auf die nerven gehen probier doch einfach mal diese 4 Einlagen aus.
The images show this replacement, in red, compared to the original and broken part, in black. This print reuses the original weaver mount and bolts.
On Request I made a pocket quiver with Martin Archery Logo. Original is with PSE logo (thing:3678462) and Switzerland flagg (thing:3724171). Did not print it myself, but should work and looks good in slicer. Please like and post picture…
Držák na luk a toulec, které je možno zavěsit na standardní 25mm vodovodní potrubí.
This nozzle holder is designed to provide easy access to 30 nozzles, visually organizes them (with custom labels and color-coding if desired) and protects them with a neat looking shell, that is opened and closed super quickly. Since…
I made a free standing arrow/bow rest for my kid. The arrows kept dropping into the bottom of the PVC adapters. I made this to plug the hole and allow the arrows to stay in place while also allowing water to drain if it gets let outside.…
A Halloween themed archery quiver tag/key chain in a few different versions.
