56 modeli
Please like and follow and post your makes This is a speaker redirector for the Xiegu G90. It was designed to be held in place by the G90-H1 bracket, but tape would also work. I made the redirection cone much shorter than the original…
I run my Yaesu FT-891 with the front prop up and that aims the speaker up and away from me. I designed this dome to fit over the speaker and push the sound more in my direction. It uses several 6mm x 2mm magnets to secure it to the top of…
This is for redirecting the filament feed from the front/left corner of the printer. This works great with my filament spool holder. Category: 3D Printer Parts
The bottom cap included with the skimmer directs outflow downward, which can disturb the substrate in shallow tanks. Swapping the bottom cap for this print redirects the skimmer's outflow forward (and to some extent, diagonally upward),…
Description I have a Tripp-Lite wall mounted network rack with a spot for 120mm intake fans on the bottom, but these blow air straight up, which immediately hits the first thing mounted in the rack and then spills out the front and sides…
Printed in PETG on a Prusa Mini+ with 0.2mm layer height, no supports (I had them enabled everywhere but none were needed), and 20% infill. I attached it to my air conditioner with hot glue. If you wanted to direct air to the left you…
You can use this with or without the Cable Spine linked below. I found that the cable was always interfering with the spool when using the stock mount and position. This will direct it out of the way. Use M5 T nuts and screws to mount, I…
After talking to a few people on reddit i can to realize that the aux fan is connected to the fresh air intake fan and can not be ran independently of that fan. the problem is if you want to filtrate your chamber, you have to run the aux…
Rotatable Fan redirector for Xiaomi Air Purifier 4 Lite with holes for the touch buttons. Fits 241 X 241 Xiaomi Air purfiers Only know that my 4 Lite fits I put my air purifier in front of my window casement airconditioner and it was just…
I liked the dome shape of DL9HAM's Xiegu G90 speaker redirector, and the elegance that it did not need supports to print, but I wanted something less permanent that could be put on/removed easily. Inspired by this clip-on stand, I used a…
Introducing the Xiegu G90 Speaker Redirector, now travel-sized for your convenience! This pint-sized prodigy was designed to hug the G90-H1 bracket like a koala on a eucalyptus tree, but if you're out of brackets, slap some tape on there…
Ok, PHEW. This is a remix of a lot of things. My wife ran across a dragon head version of this (hi! Thank you! Awesome creation!) and we're... we're more Nintendo people, so after searching extensively for a model of Wario with his mouth…
When the dishwasher air-gap is blocked, the water squirts onto your kitchen. This print allows that water to be redirected into the kitchen sink instead of the counter top.
Redirect your filament... without squeaky noises!
I have my printer enclosed and my enclosure has a top air exhaust so I want to redirect the hot air flow from the chamber fans intentionally upwards, away from the electronics and to a place where it will imediatelly be exhausted. it…
I made this beacuse the vent in my room was constantly blowing on my face at night and it helped me alot! be sure to download and like this print, i love making helpful stuff like this i added 3 neodymium magnets to it to get it to stay…
I printed in PLA with support .3 layer there are 3 holes to screw the two parts together or use super glue if you prefer
This redirects your gutter by 116 degrees . What is shown in the picture is not my intended use case for it; I intended for this to be in another area, but there is not enough space for it. So, I put it up here in case anyone else wants…
cable clip 4mm- 5mm-6mm-7mm. for ethernet, usb hdmi and many more cables!
Sick of trying to wash your hands against the back of the sink? Sick of all the water splashing behind the basin? I gotcha!. Print instructions This is a specific design for my kitchen tap, so may not help you unless you have the same…
I don't know the official name for this piece. It redirects the flow from the supply hose to the sprayer nozzle. My original part had the input nozzle break off. I figure it may be a common problem. This may be a a tricky part to print…
I found that by default the vacuums exhaust blows out and down, usually disturbing what you're trying to vacuum up. These redirect the air flow upwards, or if you like downwards. Printed .3mm PETG and stuck them on with epoxy. Works as…
Heyho. I just built a new PC and there was a spot for a 140 mm at the bottom of the Dark Base Pro 901 Case by BeQuiet. I thought about using this to get some air directly to the GPU. So I designed and printed this Air redirector :D I…
remix with sound amplifier
This Air ventilator - redirector is designed for BYD Song Ac vent to re direct some of the cold air to keep the mobile phone from heating up and closing specially in hot climate. Better printed sideways with organic supports.. ABS or Petg.
If you installed the MBR Vent Pod to allow you to replace your center two vents with gauges, then you know that you pretty much lose any and all airflow that used to come out of those vents. The problem is that the airflow does not get…
I made this because the fan of my part-cooling made a lot of backdraft that cooled the part on the bed when it moved across the bed. Large prints would release from the bed because of this draft. This 40mm fan deflector redirects the…
Sits on top of the Chitu H2 chamber heater and redirects the air flow to the top of the printer where it really makes a difference. I made this to fit in an Elegoo Centauri Carbon when the H2 heater is placed to the left side of the print…
I created this fin to redirect the hot air coming out of the back of the laptop and prevent it from being recirculated back into the laptop. The cable holder is optional. It might work with other laptops as well.
Filled some of the hexagons. If you plan to have your Ecotech MP40 near the bottom of the aquarium and you're worried about blowing away the sand, maybe this merged guard+redirector project can help. For printing tips please refer to the…
This 3D printable airflow redirector is designed to mount on a standard 80mm fan and direct the airflow underneath the laser module — ideal for blowing through the honeycomb bed of your laser cutter. It improves smoke extraction, helps…
A simple tool to redirect the garden hose water flow opposite to normal, to fill fish tanks without disturbing the surfaces. It saves me the time and effort of using a bowl on my aquarium when filling it up. Ideal for planted tanks
This is imported from Thingiverse The (2018 model) Vizio P65-E1 TV I have is designed to blast sound off a wall and reproject back to you. Well, this doesn't work if you turn your TV away from a wall, and can be quite annoying if you are…
To redirect the hot humid air coming from the dishwasher during the drying phase from the bottom of the furniture. The prototype had too small lips so I had to tape it down, but the uploaded version already has the lips 2mm longer for…
This ridiculous looking and over-engineered Printable exists because the Valve Index cable, as shipped, exits more or less toward the right side of the headset. For my setup, it would be much better if it exited toward the left , so I…
I have a ceiling duct that drops cold air right above where I sit on the couch. This design magnetically attaches to the vent and redicrects the air. If you use Fusion 360 then you can adjust the parameters of this design to fit your…
With the warmer season approaching for my location, we needed something to redirect the cool air from our central air conditioning up into the bed room and keep it from sliding under our bed straight to the return duct (cool air sinks).…
This is a very basic air duct for use in the Hovercraft event for the 2017 division B/C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Aero Kinetic Redirector or AKR for short (my…
I printed https://www.printables.com/model/1320401-centauri-carbon-heated-chamber-mod to add active heating to my CC chamber. I found the hot air goes pretty straight out of the heater making it take longer for the heat to get to where…
I believe it will also work fine on an Ipad 2 but not tested. Held on with 4 small magnets, self adjusting, takes a reasonable knock or simply slides off. Makes a HUGE difference in audio. Prints flat in 2 parts with no support needed,…
This model redirects the PTFE tube from the extruder to stop it rubbing on the sharp edges of the enclosure and stop catching on the screws. Why? I was having a lot of issues with the PTFE tube rubbing on the top glass and “shedding”…
I only anticipate using this for the A/C in the summer, you may want to print this in PETG or something more heat-resistant if you have hot vents in the winter or are placing this in view of a hot window. PETG may require the Silent //…
These files make up the pieces to put together my register booster re-director
Did a slight resize of the clean air re-direct duct by zuspiel in to match up the mounting holes to those on filter sandwich made by JKSniper. http://www.thingiverse.com/thing:2105113 Print with the same settings zuspiel reccomended. To…
This is a riser? I don't know what it is but I do know what it does since I designed it. It is a HP G4 dock mod that will redirect your thunder bolt cable so that it comes out the back instead of the front. I really didn't like how the…
Under-Bed HVAC Airflow Redirector A simple and effective airflow redirection tool designed for HVAC or central air systems. This part attaches to standard rectangular floor vents, guiding cool or warm air from under a bed or obstructed…
This is a simple derailleur cable redirector. Some derailleurs (most notably, the Shimano GRX series) will redirect the end of the cable directly into the wheel requiring you to cut the end of the cable, even if by a measly few…
Behold: The Great Snack Redirector 3000. A funnel engineered for one noble purpose — getting snacks INTO the container instead of all over your counter, your shoes, and that one floorboard the dog is already eyeing. It spins perfectly…
The air purifier propels air straight up, but I needed to redirect the flow horizontally, so I made this 3 part print to redirect the air. Printed at .2 layer height with a very low infil, slip fit on the top of the air purifier. Print…
This is a simple model made to clip on to the round cover of the wall or ceiling duct vent. In my case the diameter of that cover was 6.75", but the model should be fairly flexible to accommodate slight variations in sizes. I have two…
I created this fin to redirect the hot air coming out of the back of the laptop and prevent it from being recirculated back into the laptop. The cable holder is optional. It might work with other laptops as well.
I liked the dome shape of DL9HAM's Xiegu G90 speaker redirector, and the elegance that it did not need supports to print, but I wanted something less permanent that could be put on/removed easily. Inspired by this clip-on stand, I used a…
cable clip 4mm- 5mm-6mm-7mm. for ethernet, usb hdmi and many more cables!
This model redirects the PTFE tube from the extruder to stop it rubbing on the sharp edges of the enclosure and stop catching on the screws. Why? I was having a lot of issues with the PTFE tube rubbing on the top glass and “shedding”…
You can use this with or without the Cable Spine linked below. I found that the cable was always interfering with the spool when using the stock mount and position. This will direct it out of the way. Use M5 T nuts and screws to mount, I…
Rotatable Fan redirector for Xiaomi Air Purifier 4 Lite with holes for the touch buttons. Fits 241 X 241 Xiaomi Air purfiers Only know that my 4 Lite fits I put my air purifier in front of my window casement airconditioner and it was just…
