Liczymy pasujące modele…
I stopped uploading and updating my models here at Printables! My actual models can be found on my MakerWorld profile – with print profiles. Take care to use the newest models … Similar to GekoPrime's Clip for the other places. But this…
Untested work in progress
This safety eyes need to be printed with low layer height (0.1mm) to achieve a nice result. The eyes are made from two different parts for ease of printing (the rod and the head) that need to be glued together, and also it make it easy to…
A parametric case for standard 1/4″ hex bits , designed for practicality and flexibility. The main case is print-in-place and uses 4 mm DIA × 1.5 mm or 3 mm thick magnets to keep it securely closed. The spring tabs in each row hold the…
This is a remix if the inner portion of my original model. This one is intended to be printed with rigid filament (PLA, PETG, ABS, etc.). It has the corresponding number of holes on the bottom to insert 6x3mm magnets for bit retention.…
Every time I loosen up the two Idler tension screws and open the MMU2s one or both of the screws and their springs would fall out. They would bounce around and play a mean game of hide and seek. So I made these little guys. Literally the…
Hook part extended by 5mm on both mounts. Category: Computer
I designed this feet / legclips for the IKEA kitchen METOD and its plinth FÖRBÄTTRA to: be more stable with PLA and PET be printable as one or multiple parts (to glue together) have multiple length to avoid “Aufdoppeln” and fit my needs…
This a replacement for a common part that fails in most socket AM2 AM2+ AM3 AM3+ FM1 FM2 machines. I have only used it my AM2+ machine. I would recommend that you print it in a vertical orientation with walls set to 99 and infill set to…
Uses 4 M3x15mm bolts 4 M3 nuts 4 M3 washers (optional) The backplate has a second version which doesn't require supports and will bridge the overhang instead Consider rotating the retention mount for better strength. That will instead…
Remix is the head (8mm) and rod piece together as one piece. No glue required.
Printed with no supports, .2 layer height, 4 top and bottom layers, 3 side layers, 40% infill.
You probably printed already "Cat toy playing board pegs play" and your cat figured it out pretty well or you have more than one cat and the board is simply to small for both of them. Then you need this collection of extensions and…
Key Features of the Door Seal Add Heat Retention: Our door seal brings the heat, literally. It's all about insulation, creating a stable printing zone that spells primo print quality. Reduce Drafts: Reduce unwanted temperature shifts, the…
Sovol SV08 closed top extention lit with filtration. You can use Roborock S7 Hepa filter and carbon filter at the same time. Upgrades: Fully closed Stackable Filtration Cut-outs for the fan and the filament sensor cables Every parts…
The newest Mattel Pixar Cars track sets (2023+) use a redesigned road connector piece. The new design has smaller connectors (which are easier to connector/disconnect) and all road pieces have attach points on the sides to connect…
Quick printed version of the kydex AR mag inserts you'll find in nicer pouches. If printed in PLA they will creep over time, but I've found the retention to still be pretty reliable over time. Obviously higher temp resistance materials…
The SV08 Top Extension is a crucial component designed to enhance the functionality of 3D printers. This extension ensures that when a glass plate is placed on top of the printer, the flying gantry can reach its maximum height without…
Print instructions: 0.2mm layer height 4 walls for strength 100% sparse infill Turn off single layer for Top Surfaces
Many printers, especially those with a Bowden extruder, use PC4-M10 fittings to retain the PTFE tube at the extruder. Reportedly on Bowden printers it helps with retraction if the fittings at both ends have a firm grip on the PTFE tube so…
Updates 29-09-2024: Uploaded a 5-piece split model (inform me if it doesn't fit your printer) 26-09-2024: Uploaded the complete file of the front fender. (.step and .stl available) 01-05-2025: After some trial and error, we found out that…
Gridfinity holder for socket/female side of USB A devices. I use mine to hold USB A to USB C adapters. If desired, there is also a looser fit model. The base model is a friction fit that acts a pseudo handle. Printed with PLA+ (regular…
This .scad will generate a ball bearing retention ring of any size you want with any number of balls! I created it to work with Airsoft pellets (BBs) but it will work with any ball or sphere shaped object. The idea is to use this in a…
This is a remix of fellow Phil's excellent Pastamatic retention pin available here: https://www.printables.com/model/100. , to combine with the original Pastamatic, available here:…
Pastamatic Filament Spool Winder Add-On by Kistek. This add-on is for Pastamatic filament spool winders and is meant to secure the drive spindle so that it does not come out of the cradle during operation. This is especially important for…
Are you ready to experience the next level of gaming convenience? Introducing the phenomenal Wall Mount Bracket Remix for the Nintendo Switch! Brace yourself for a description that will make your heart race, your palms sweat, and your…
A simple Flag pole holder. Anchor/bolt spacing based off standard brick joints and using 3/16" bolts. Sized for a 1" flag pole. Infill: 20-30% Infill Modifiers: 99-100% as shown in photo Support: Yes, Tree Walls: 4-6 Top/Bottom Surfaces:…
Retaining clip for DieselGeek's amazing first gear getter bushing. Under heavy use, the bushing may fall out due to its friction fit. This 3D printed plastic clip slides over the bushing and holds everything securely in place. You can…
Cable Retention Bushing / Gland for USB cables, for example from arcade sets from Aliexpress. Lock tab is 8 x 8.5 x 1.6 mm. Cable is 4 mm. For holes 18 mm or 22 mm. I printed a layer of 0.16 mm.
I love my Omnifixo clamps. They are so far the best third hand I have found. But for clamping some objects it would be helpful if the clamps could be on different heights. Sure, you can stack the yellow parts of the clamps, but as there…
I really like this extension because you can take out the scale to use on the counter and the drip tray just rests on the sides of the base. It is a low profile drip tray, I need to drain it after each flush-brew-flush cycle. Cleaning is…
The Impulse Ungineering Ontos O-ring Breech is a modified breech part that uses a DASH-016 O-ring to assist with barrel retention. The O-ring adds extra friction where excess vibration from play may push the barrel out of the blaster.…
1,5 - 0,25 inch 45 Record Adapters - Contest Model - Correct Version Now. Sorry I had made a big mistake in my first upload. ATTENTION!!! There was a change in the match schedule. Initially, the opening diameter was specified as 0.25…
This is a box for up to 3 sd cards, that is made to be durable, with spring loaded retention brackets to make sure the SD cards don't fall out. There are two versions, either a print in place one, or one using a 12mm M3 bolt and nut. The…
Die of death figure from roblox. Stylized to my prefrence.
This is the original "SV08 Top Extension Lit" in a closed version. Given the potential for higher temperatures inside the 3D printer, it is advisable not to print this part using PLA. Instead, using more heat-resistant materials like…
While using the original model, the parts always fell apart when my cables would move slightly, so I designed this little press-fitted cap to fix this problem. The whole inner assembly could still leave the outer ring at that point, so a…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, please consider buying me a coffee , and check out my other models ! ********** I've tried a few of the bit holsters out there but none seem to have worked for…
Replaces the spring and blade retention pin with a self retaining spring and a larger base pin, also adds one more locking lobe so the spring doesn't get squished. Print Settings: Layer Height: 0.2mm Infill: 30% Material: PETG Supports on…
Prevent your Powerpole connectors from accidentally separating. The clip fits into the existing retention holes with a slip friction fit. Still removable by fingers thanks to a ridge on the clip, but will stay under vibration and normal…
An upgraded go-pro compatible holder for the UV5R radios. There is an added slot for better belt clip retention to help prevent movement under off-roading conditions. It also significantly helps reduce noise from the radio rattling around…
This is a retention sheath for a full sized Kabar (1211 in my case). The sheath has two lugs that bend downward when inserting the knife into the sheath and spring up behind the cross guard, retaining the knife in the sheath. To remove…
The retention clips are quick and easy to use, except a bit fiddly to open. Added finger tabs to make it easier to manipulate. Remixed both the normal retention clips, and the larger one that is for the drive side on the receiver spindle
Redesigned from scratch for the OLED variant's dimensions and features such as speaker ports and vents. Added retention clips to hold the device in the mount for added safety. Retained the original aesthetic although slightly modified,…
This is a replacement nut used to clamp the shade in place on my lamp's light socket. The factory's original part broke due to heat fatigue. I printed this model on my Prusa MK3S+ using polymaker's "Galaxy Black" 1.75mm PolyLite™ PLA…
This is a remix, adjusted and optimized for TetherPRO cable and Nikon Z6 Mark II
Tired of cutting yourself on your chisel when you dig for something in your toolbag? Or sick of finding out that the chisel you just sharpened has been dinged by another tool in the drawer? Fear no more, these guards are easy to print,…
This is a snap down retention bracket for hard drives and SSDs in MODE. Normally a SATA drive is secured down to MODE with 2 screws through the bottom. However that means you need to remove MODE from the console to get to the bottom of…
The original shaft had a tendency to slide off the side supports during use, so I extended it by 2–3 mm and added holes sized for an R-clamp to keep it securely in place. Printed successfully in both PLA and PETG without issues. For…
Simple zipper pull extention.
These are fun because they are supposed to be bad. Anyone who's opened a SpongeBob popsicle knows that the placement of the eyes/mouth/teeth can be way off. So there's pretty much zero pressure while building these because the worse it…
ATTENTION: this case requires foam or something similar in the lid to keep the battery in place, if not they can come loose an mix an cause fire. i shared some images of one that had this happen an only thing that saved it was the…
Print 100% infill. I've used PETG because it need to be flexible. Mount between the adapter and the spool winder as you can see in the image
10mm extention i needed for the cchand front bumper on my bronco
I found the original version very good and useful, however I usually squash the first layer so the part came out rather sharp on the edges, this remixed version have a chamfer for softer grip. Also, I didn't want to glue the socket…
the threads are m36x2 with 0.1mm clearance. I made it to use it on my chair i hope you guys also enjoy with that. I am going to use it with THIS
Remixed the strongest pegboard clip I've seen to make it a bit more sturdy and added removal openings
Concept 2 rower phone or device rest/mount remix of model from Leoquart
A quick remix of figterk's excellent bit holder for the LTT screwdriver. This is the 60-bit insert, split into 5 pieces. This is a split version of the 60-bit insert, enabling users to easily print in multiple different colors for each…
This is a remix of the original to address a few issues I had: Cover was sliding off the back on some long prints due to vibrations Extruded the lip to match the front two pieces to fully retain the glass top PTFE guide was allowing too…
Got tired of the Velcro pads failing constantly, forcing me to adjust the floor mats every damn time I got in the car. This is my solution. Printing: Small part, so go 100% infill @ .2 or smaller Button face down Organic supports on…
Full reduced friction feeding system For extruder number one on the Prusa XL from the left side mounted spool holder using an additional filament guide mounted using the same method as the OEM filament guides. The natural spring tension…
I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work. There is already a solution for this here. However, I didn't like it because it is too bulky and you have to buy screws.…
I had mounted my Argon Neo on the side of my Lack Enclosure, but was having issues with the case falling out of the mount over time. I remixed the design to introduce a retention clip. I opted for an interchangeable clip to allow reuse of…
Requires 10-32 screws, 2.5" lg, qty 3
Filament Spool Holder Retention Clamp for Bambu Lab A1 to prevent the filament spool from slipping off the filament holder My print settings for PLA: 0,2mm layer height 5 walls only one wall on top and bottom layers 5 top and bottom shell…
These extensions are designed for Vudoo Gun Work's .22lr AICS magazines. I use 10 round polymer magazines, and these will not work on the aluminum magazines. In a 10 round magazine you can load 11 rounds with the loading button installed…
I used support 25% infill https://biqu.equipment/collections/lcd-screen/products/bigtreetech-hdmi5-v1-0-hdmi7-v1-0
AM4 Retention Bracket for a iCUE H150i ELITE CAPELLIX Liquid CPU Cooler. Corsair has a retention bracket for sell on its web site. It is currently not in stock. So I designed this bracket in blender. 6-32 3/4 Screws is what I used to…
Pieces should fit together nicely if opting for a multi coloured print. A bit of fishing line or string and some super glue for the whiskers and maybe a dab to keep the clip on the end of the stick. 100% Success rate tested on 5 cats and…
I have taken this idea from the "Multigrid Bin Extension" by Keep Making. and adapt it to the gridfinity system. This allows to extend the length of already printed bins with out reprinting them. I have made an parametric model in Onshape…
Ich habe für meinen Paulimot Messchieber 300 mm ein paar Erweiterungen gebraucht, um tiefer in einer Box messen zu können. Also habe ich mir diese Erweiterungen konstruiert. Sicher sind diese nicht so genau und da es Kunststoff ist,…
This was designed to compliment the Pixar Cars Tracksets. The ends of this road piece are designed to connect to the ‘older’ tracksets with the thicker triangular connection arrows. The ‘newer’ tracksets have much smaller connection…
I created this model to store the cable I use for hooking e-matches to my DIY electronic fireworks rig. Each currently has about 15m of bog standard speaker cable on in. The spools are easy to churn out and put together. They have a key…
Jack retention/support system nut for Dacia/Renault Dokker also known as Renault Kangoo in some markets. It's an original model very close to the original part. the center screw hole Isn't fully threaded, you can directly thread it on the…
For extra strength use 3 or more wall loops. Different models for more or less bit retention, retention weakens with use. (Its plastic what can you do?)
These TPU retention sliders hold hydrofoil T nuts in your desired position between sessions. They speed up assembly and disassembly before and after foiling sessions. They are easy to install, and slide to reposition with a hex or torx…
I desinged this stick cover for the radiomaster pocket since I wanted to have more controll. It fits snuggly over the original metal sticks, no hardware needed. I made it to fit around 8mm sticks.
Apple charger | Iphone, Airpods, Apple Watch but for airpods pro
With my New direct drive Hot end cable management through the frame and out the back was not overly practical for taller prints so I made this bracket to retain the cables at the front over the X Axis end stop. Print Settings Printer…
Should be compatible with any Crosley Cruiser portable model. Printed in PLA with 0.1mm layer height, 2 perimeters, supports everywhere.
The original front/side panel retention clips on the Jonsbo D41 computer case are lousy and brittle. I decided to make these when I accidentally broke 3 of the original clips when attempting to put my side panels back on. I was able to…
Replacement panel retention clip for Silverstone Fortress tower cases such as FT03 and FT03-mini, may also work with other Silverstone cases. This is the small piece that screws into the side panels that allow it to clip into the case…
A what? With the world returning to semi-normalcy, but tele-interaction becoming even more common, sometimes it's necessary to have a "busy" indicator that can be seen easily from a distance in an "open office" setting. Stick the base to…
Very good surge protected extension lead, unfortunately no fixing holes to wall mount it. Here's my quick attempt to design some brackets for it. Hope you find it useful. Please let me know if any adjustments are needed. Designed for 0.4…
Like for most others with a Tronxy XY2 printer the MicroSD Slot is very inconveniently positioned at the back of the printer and I've used a MicroSD Extender to bring it to the front. Looking around Thingiverse I came across someone…
Tonneau cover strut retention is a small plastic clip that the cover strut snaps into during travel. REV01 added rib for increased strength. Tonneau cover is made by BAKFlip, model 448329;…
ATTENTION: BATHROOM CAMERA IS FOR RESEARCH PURPOSES ONLY, novelty sign Category: Signs & Logos
Tibialis trainer extention for a dumbbell! This allows you to train train your tibialis, the muscle at the front of your legs, and strengthen them. Great for preventing shin splints and general athleticism. It is a single piece, built for…
A very secure clip that holds cable along a piece of 2040 extrusion
If you have long jobs with your diode laser, thats may be a eye safer
A parametric set of organisers for standard 9.5 mm and 13 mm (Japan) driver bits—perfect for keeping your tools secure and tidy in a toolbag. Each slot uses spring-tab retention to hold the bit firmly in place so it won’t rattle loose or…
I lost my original stock bracket and cpu cover as I had used an aftermarket aluminium support bracket for better pressure distribution. As I wanted to store my motherboard in its box, I remixed this design to allow me to cover the socket…
No more wimpy pegboard retention clips. This one has some stout. It hold fast and you may even need a flat blade screw driver to remove it. Happy Printing! You can help To help cover the expenses of printing prototypes for the models I…
This is a mount for a Baofeng UV-82 with plug retention. The application is for a 24 Hours of Lemons car and mounts to a round dash bar, but there may be other applications so I uploaded it here. The clip around the side prevents the…
This is a remix of Mordiev's MMU2s Tension Screw Retention Washer designed for printers with .6mm nozzles. For whatever reason, the inner diameter (ID) of the original washer design was too big and kept falling off of the idler screw - I…
Extention based on this cup design. New cup holder and extention. No supports needed, but have rely strong bed adhesion, I had no problems with printing even with this steep angle on my ender 3. I added a test file if you wanna try the…
put this on your desk or anywhere you want to let people know it is a fart zone!
