Liczymy pasujące modele…
I had to cut long curtain rail Ikea Vidga into two pieces, but there were ceiling mount holder only for one part, therefore I created this model so I could use the other part, too. The original holder design is slightly modified for…
Connector for IKEA Vidga rails to make a solid connection. Uses the set screws that come in the end caps with the rails, or any m5 bolt. Category: Decor
I needed to connect two Ikea Vidga rails together without putting an extra bracket on the wall, designed this little connector to fix the issue. Designed to use brass inserts and M3x12 screws, works with longer screws but they will stick…
Upgrade your IKEA VIDGA curtain rod setup with this improved and highly overengineered connector! Designed to be significantly more stable than the original IKEA part, it minimizes wobbling for a cleaner, more secure curtain installation.…
Spare Parts Ersatzteile für IKEA Vidga Vorhangschiene: Verbinder und Befestigung
Clips to connect IKEA curtain to the Ikea Vidga Roller. As you can see by the picture, the design is practically 1:1. I printed it scaled up by 25% in x and y, so that it prints easier, also i needed the clip to be slightly larger.
Print from PETG with 100% infill. No supports needed.
I changed the part in order no to be visible from below. Therefor I did thighten up the tolerances an removed the outher part. Furthermore I changed the screw set-up to accomodate what i hat at hand. The connector is now fixed by two nuts…
The rails for the VIDGA curtain system are attached to the ceiling by two flimsy plastic part and interconnected by another, equally flimsy piece of plastic. When I tried to join two rails, they were misaligned and twisted against each…
Local ikea was out of stock of the Vidga Gliders with hooks https://www.ikea.com/us/en/p/vidga-glider-with-hook-white-20483002/ . 3D designed replacements. Recommended to print on side with supports as this allows for stronger prints.
Ikea Vidga curtain system is a great system. None of the standard parts fitted my needs for mounting the rail on the ceiling so I made my own additional parts. One for better extension of two or more rails and one to fit a 60mm ceiling…
IKEA Vidga Wagen roller. gebruik de orgineele asjes en rollers weer
Jeweils zwei Verbinder werden in die Schienen geschoben, damit die Schienen besser fluchten.
These were made as replacements as mine broke due to heavy curtains and lack of rail support on the wall. The rail stop has a loop for a nail/screw against the wall to offload some of the curtain weight. Print without support. The joint…
We have the problem that the small gliders inside the rail will chop where the rails are connected. This small gimmick will connect them better and let the glider "flow" better. OpenSCAD File included, if you wanna make them shorter or…
If you want to use this mount you have to cut your rail. I reccoment cutting rail to width of the place you want to put it in -7mm. You can put it right to the ceiling when mounting. And don´t forget to put those hangers first :) . I…
Summary: I needed to replace some lost IKEAD VIDGA ceiling rail brackets but couldn't find a sufficiently optimized model ready made. I designed a new bracket from scratch using the measurements of a spare I found. My reasons for…
Thanks to @chwiede_775251 for the original model, I really liked the idea of it to be a bit springy to squeeze into the rails. However I don't have so many M4 grub screws but a lot of windows where I need to use the connectors. Replaced…
This is a remake of the "Ikea Vidga Rounded Section" curtain stop when you have little clearance above the rail. The regular piece requires the skrew above the rail for which I just didn't have the room (wanted it as close to the ceiling…
A replacement part for Ikea VIDGA panel curtains No. 146964 / 146965 Print Settings Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 100% Filament: SUNLU PETG Category: Replacement Parts
Insert the aligner between the rails and push against each other for the perfect fit. Sawing holder for triple rails included too. Thanks in advance for uploading the makes! Print instructions Category: Household
I'm building a cargo trailer camper and I'm using the Ikea Vigda sliding track suspended from the ceiling for the shower enclosure. Unfortunately when you buy the track it only comes with two hanger clips and I needed a couple of extra…
This thing allows you to connect 2 VIDGA pieces together permanently, without any chance of them popping away from each other. It also creates a completely flush connection, which is not visible from the side. You need 2 M3 6mm screws and…
IKEA Vidga spare rollers Wedge Shape for sliding instead of Rollers Click-In mounting System for convenience 4 M3x6mm-10mm Countersunk Screws per Pair An over-engineered Alternative for the Vidga Rollers.
The beloved spouse asked for some motorized curtains. As we live in IKEA-country, we have the IKEA Vidga curtain rails already in a few rooms. The simple solution was to get a few of Aqara's Curtain Driver E1's However, the IKEA Vidga…
Print with 100% infill and 0.25cm layer height
I printed it with white PLA to match my curtain panels, but you can print it with silver PLA to match your panels. You may want to scale up in 0.1mm increments to fit the curtain holder rail properly according to your printer settings…
During attaching the 3-railed Ikea Vidga system to our ceiling, we needed to shorten the 3-railed curtain rods. As we calculated to reuse the access parts on other ceilings, we needed more ceiling mounts for those spare parts, as just two…
Not suitable for PLA - use PCTG or ASA. A slightly more narrow and tall IKEA compatible curtain clip. Same max thickness as the original but more durable* and easier to attach to both rail and curtains. Includes locking slot such that it…
Hallo, ich musste mir für die sehr instabile Verbindung von der IKEA VIDGA etwas einfallen lassen. Es ist einfach aber sehr Stabil. Ich habe es mit einem Infil 100% gedruckt. Gruß Bernd Hello, I had to come up with something for the very…
Recreated Ikea Vidga holder for Hugad curtain rod . Original was made from the alluminium. This plastic replacement must have 40% infill and must be printed from a strong material (PET-G). We used the Filament-PM and holder is not broken…
Miter box for cutting Ikeas Vidga rails... print it with full infill for most robustness
I installed a longer continuous section of Vidga rails across two windows and wanted to have a point in the center where I can attach the curtains for each window. Thanks for @Blizz for the original model. I only cut off the endplate and…
Useful for supporting for example a single corner piece that is not properly supported by the IKEA connector. Will need a fomay double-sided self-adhesive tape and needs some support when printing.
Provides mounting for a stepper, optical encoder, belts and pulleys to open/close your curtains using IKEA Vidga track. https://philsprojects.wordpress.com/2022/10/13/ikea-vidga-curtain-opener/
Edit 1 - 8 Feb, 2024 Based on the feedback I received on the first upload of the design, I modified my design and have uploaded a new STL. This should be even better at catching the neighboring curtains. The wings are wider, the height…
A model to connect two IKEA Vidga rails together. Uses bolts to hold it securely attached to the rails keeping the rails securely holding in place. The M5 bolts and nuts can actually be found in every IKEA vidga rail packs. it always…
Recommended print settings: Material: PLA or PETG Infill % : 30+ Top/Bottom/Wall: 5x Supports: Yes Print Orientation: Default as modeled Brim: No
Inspired by 3D-Print Brehm 's Model, which unfortunately did not fit for my 3 wide rail, I decided to design a similarly optimized spare part for the Vidga triple rail. No special settings are required to print this model, however, print…
Fast way to mount your DT62 tracks in VIDGA wall mount Recently I bought DT62 tracks together with Aqara Smart Curtain Motor, but I already had wall mounts for VIDGA tracks from Ikea. This small adapter allows you to easily combine them…
90° Verbinder für IKEA VIGDA Gardinenschienen
To install a Vidga curtain rod on a Pax wardrobe (Ikea), you will need single "Pax - Vidga Connectors" for the right and left sides. If you have several Pax wardrobes assembled, you will also need double connectors. The connectors are…
My little project contains some accessories for IKEA VIDGA single rail stuff. I had some problems during mounting over long distances (~12m). So, I had to improvise a little bit. Therefore, I created three different accessories to fulfill…
Check my other IKEA designs: Ikea Metod Screw On Leg Extender (402.055.99) NEW Ikea Metod Leg Extender (705.560.67) IKEA Metod Back 10mm Spacer Replacement (10036383 or 10039201) Mount for the Aqara Curtain Driver E1 (Track Version,…
The two side connectors have a slot to insert a flat screwdriver when inserting the connector so that it remains centred. Use M3 heat inserts and M3x8 screws to fix the central connector to the rail with a little space from the border.…
This curtain connector extension helps to keep the curtain rails straight. It is especially useful for the corner pieces, as these would create some bend on the original connector otherwise.
Simple mount to install two IKEA Vidga rails with the end to a wall. You need the following parts. 1x M4 40 mm wood screw with dowel. 1x M4 10 mm washer 4x M4 nut 2x M4 8 mm Allen screw 2x M4 grub screw The model was created with FreeCAD…
Adapter to attach Ikea "Vidga" sliders to classical curtain rail as commonly found in German houses. Please check the measures first, or print one test part before starting mass production - there seem to be countless variants of that…
Diese Kappe für die Ikea Vidga Schienen haben einen anderen Druchmesser für die Laufschienen. Ich habe hier einen Durchmesser von 9,6mm verwendet. Da meine Schine Zuhause nicht von Ikea war ich aber die Halter von Ikea nutzen wollte.
Compatible with IKEA VIDGA rails, wall mount 120cm.
Recommended print settings: Material: PLA or PETG Infill % : 30+ Top/Bottom/Wall: 5x Supports: Yes Print Orientation: Default as modeled Brim: No
The project, which involved around 36m of IKEA Vidga curtain rails, required more than one cut; in the end, it took 24 cuts. I already had a standard miter gauge, but it was too cumbersome to clamp the curtain rails with two clamps each…
Simple mount to install two IKEA Vidga rails with the end to a wall. You need the following parts. 1x M4 40 mm wood screw with dowel. 1x M4 10 mm washer 4x M4 nut 2x M4 8 mm Allen screw 2x M4 grub screw The model was created with FreeCAD…
Diese Kappe für die Ikea Vidga Schienen haben einen anderen Druchmesser für die Laufschienen. Ich habe hier einen Durchmesser von 9,6mm verwendet. Da meine Schine Zuhause nicht von Ikea war ich aber die Halter von Ikea nutzen wollte.
Compatible with IKEA VIDGA rails, wall mount 120cm.
Adapter to attach Ikea "Vidga" sliders to classical curtain rail as commonly found in German houses. Please check the measures first, or print one test part before starting mass production - there seem to be countless variants of that…
Remix of the IKEA Vidga curtain slider - adjusted to fit in smaller curtain rails
Replacement part compatible with IKEA VIDGA (146963) sliding curtain end caps It's about 2mm shorter than the original. I made it this way so it can be printed without supports and still have the best orientation for strength! Took about…
The project, which involved around 36m of IKEA Vidga curtain rails, required more than one cut; in the end, it took 24 cuts. I already had a standard miter gauge, but it was too cumbersome to clamp the curtain rails with two clamps each…
This upgraded connector is designed to provide a stronger, more reliable joint between IKEA VIDGA curtain rails. Unlike the stock solution, it uses embedded M5 nuts and grub screws to firmly clamp the connector in place, reducing movement…
Summary Spare part for Ikea VIDGA ceiling bracket Print Settings Rafts: Doesn't Matter Supports: Yes Resolution: 200 Infill: 80 Filament brand: No name Filament color: White Filament material: PLA
Update on 24/05/2020: The clamp has been reinforced and the "spindles" has been separated from the body so it's necessary to assembly. The Ikea Vidga rails are very fragile and if when mine was broke I decided invest 1 hour in design a…
The Vidga rails can be hard to align which can make moving curtains hard. Add two joiners to each joint to align them and make moving super smooth. I would recommend printing them in the colour of your rail system to make them less…
You are probably better off just buying a bag of these if you're going to use a lot of them, but in case you just need a few or just prefer printing them yourself this model is tried and tested.
For 3D printing: I has been used ABS material because it is quite tough. Because wheel is very small it is best to use small nozzle like 0.25mm I has been increased hotend temperature +5°C above default The wheel diameter is set +0.1mm…
Hello guys, my problem was, that I don't want to screw a new curtain strip into our ceiling. I created glides to use the Ikea Vidga Curtains on our standard 7mm curtain strip. The clamp was print with 20% filling and without support…
I bought the Ikea Vidga curtain rails to replace the ones at home, during installation on the ceiling we managed to break 2 of the connectors between different rails. mocked up this easy to print easy to install and quite sturdy…
Simple clip that inserts in a 3 wide Vidga curtain rail and can hold a couple of cables next to the rail. There are two versions; the normal one and one that can fit if you use a switchbot curtain opener.
When I assembled the IKEA Vidga curtain rail, I had some leftovers that I decided to use for a simple shelf for LED light above my desk. Here, I'm sharing the models for connecting individual Vidga curtain rails, they might come in handy…
The curtain IKEA VIDGA glider & hook combo were not compatible with my curtain rails so I decided to design and 3D print new gliders for it. Design was inspired by: https://www.printables.com/model/731868-curtain-glider - This design got…
The included connectors are really bad at lining up 2 (or more) Vidga rails, especially when using SwitchBot Curtain3 (U Rail). Tested with IKEA Vidga 1 track. Press fit, no screws needed. I have also added a distance to rest at the…
I needed a 45°/135° angled IKEA Vidga corner piece but IKEA only sells 90°. So I created an OpenSCAD model where you can set any angle you want. Adjust angle and radius in OpenSCAD file Printable with minimal supports. Use brim
Took the original design of the VIDGA rail corner wall attach end stop component and placed the tab with the hole for wall attachment on the other side. Used fusion 360 (non commercial edition) - attached is the original file.
