110 modeli
Wandhalterung / Wallmount for AVM FritzBox! 7490, 7590, 3490, 6490, 6890, 5491, 5490 Lochabstand 197mm space between router holes = 197mm NEW Wallmount for 7530 with PETg from DasFilament Print Settings Printer Brand: Creality Printer:…
Halter für FritzBox 7590 AX um diese mit 2 Schrauben an der Wand zu befestigen. Den Halter kann man auch so als Tischständer benutzen damit das Gerät eine bessere Belüftung von unten bekommt. Drucken im PrusaSlicer : bei den Haken…
Here's my FirtzBox 7590 Wallmount to mount that great box upside down to the wall with some Space behind the Box to do clean cable management. Just print it like it's shown in the slicer Picture. It can possily fit on the smaller 75x0…
I want to create a stand for the FritzBox 7590 AX V2 which provides the following features: parts shall easy to mount to the Router the router should be placed tilted to have a good ventilation to the board inside all connector should be…
Wallmount for AVM FritzBox Router with cable management 7590 7590 AX 6660 Cable 7530 5530 8850 6850 6660 6890... It keeps the Fritzbox cool and ensures better WLAN Performance due to fewer reflections from the wall. Affiliate Links for…
Vertical stand for the Fritz!Box 6660 cable. Inspired by https://www.printables.com/model/43735-fritzbox-7590-stand If you have a different model check if it has the same housing. The diameter should be around 54.5mm
I was tired of paying a lot of money for a really nice, and light weight Mattebox for a gimbal or steadicam So I made this! Hope you like it, I worked really hard on it. Print instructions Hey friends! I moved this over from Thingiverse…
Use these brackets to mount the Fritz!Box 5690 Pro to a wall, shelf or cupboard with screws or power strips. The existing model has been optimized as follows: Slopes were added to enable printing on the side without support, reducing the…
Rackmount für die FritzBox 7590 im 19 Zoll Serverschrank. Dabei können die Anschlüsse der FritzBox über bis zu sechs Keystone Adapter nach vorn herausgeführt werden. Folgendes wird zur Montage der beiden Teile benötigt: 8x…
Hey guys i'd like to share my recent bigger project with you, my 10 inch Network Rack. I was always disappointed when i saw all the mess and not really organized cabling and setup of my network devices at home. Inspired by another 10inch…
UPDATE 2025-08-21 Based on some reviews and comments, I've revised the models and this time separated the models for the 7590 and 7590AX. I've moved the mount for the 7590 slightly. I removed the covers from my cabinet and my neighbor's…
Ergänzung 11.01.2024 Habe eine Ausführung mit Aussparungen für den TAE und USB-Anschluss hinzugefügt. Diese habe ich nicht getestet. Bitte um Feedback, wenn es nicht passt!!!
This is an stand for Fritzbox! 7590 (don't fit to 7590ax) it provides the folloging features: parts shall easy to mount to the Router the router should be placed tilted to have a good ventilation to the board inside all connector should…
For the Fritzbox 4060 router to attach it to the wall. I did it relatively precisely and the bracket clamped over the feet below
Rackmount 19" for the FritzBox! 7590AX. This rackmount does not route the rear connections to the front in case this is not required or they are not used at all. To mount the two parts use some M3 bolts.
10" inch Mount for your FritzBox 7530 AX in a 10 inch network cabinet. Nozzle: 0.6 mm Print Settings Printer: UT5050 Rafts: Yes Supports: No Resolution: 0.4 Infill: 12 Filament: M4P PLA natur PLA natur Category: Other
Wall Mount for Fritzbox different Models.
Seriously, I only needed the stand to place the Fritzbox 6670 vertically in the cabinet due to lack of space. The model should also work for the Fritzbox 6660.
Resized 1U Rackmount 19" for the FritzBox! 7590AX. Keystones on the right side
This is a 19" rack mounting bracket for 7490 style FRITZ!Box internet routers including mounts for a 5 port PoE Switch by TP-Link and 3 slots for russrosss awesome raspberry pi mount. I have also included the Freecad file so you can…
Habe eine einfache Wand / unterm Tischhalterung für eine FritzBox 5530 (Fiber)/7530 AX gebaut. Sie wird einfach nur mit 4 schrauben befestigt. Es gibt keine besonderen Druckeinstellung. Drucker : Prusa MK4s Filament : Prusa Galaxy Balck…
English This is a specially designed mount for securely and space-efficiently installing the Fritz!Box 7590 AX (V1) in a 10" server rack. It is ideal for use in IT environments where organized and tidy storage of networking equipment is…
We created this bracket for the ZOTAC ZBOX Mini PC to use in our interactive table made for Sekisui Plastics. The bracket allows any of the previous and current ZBOX Mini PC's to be mounted to any surface. The VESA mount holes on the…
Cooling Base for your AVM FRITZ!Box 7530 (AX) Got a spare PC case fan you aren't using? Print this cooling base for your router! Two variants for use with 120mm and 140mm case fans available. Print the optional standoff feet, when using…
This is my version for a mount for AVM FritzBoxes. It should fit the following devices: 7490, 7590, 3490, 6490, 6890, 5491, 5490. I have a 7490 and it fits perfectly. I made sure to use as little material as possible. The holder fits very…
A quick'n'dirty remix of a FritzBox Wallmount with flat backplate for double sided gluetape
Allgemeines Habe hier eine kleine Box in Form eines Herz entworfen. Der Deckel benötigt keine weitere Skalierung. Das Modell ist beliebig skalierbar. Druckeinstellungen Drucker: Prusa MK3s Schichthöhe: 0,15mm oder 0,20mm 10% Gyroid Infill…
Ständer für die Fritzbox 5530 leicht zu drucken
Hallo, habe im Internet so ein AVM Fritzbox Rackmount gesehen gehabt und fand das ganz cool also eben selbst eines gezeichnet. Habe auch für einen gekauften Fachboden, nur die Keystone Halter mit hochgeladen, und eine Kappe um die Löcher…
Meine neue Fritz!Box hat bei Wandmontage die Kabelanschlüsse unten. Das paßt mir nicht und deshalb habe ich eine Wandhalterung mit FreeCAD 1.0 entworfen und mit ORCA gedruckt. Nun muß das Ding nur noch an die Wand und das…
Allows the Fritzbox 7490 to be mounted under an desk. Easy print
Sep 02, 2021 This is a mounting plate / wall bracket for the Fritzbox 7360, 7430 and identical models with a mounting hole spacing of ~178mm. After fixing the mounting plate to the wall, the Fritzbox can simply be hooked in. The side…
This is my Fritzbox 5530 Wallmount with a little dust shield. In addition you need two M4 inserts and two M4*12 screws (maybe some Loctite).
I wanted to have an easy to print wall mounting device for my FritzBox! 5690 that I can attach to the wall with the connections up. The version from SteveBa (thanks for the later help) seemed to be perfect but unfortunately was for the…
This is a 10 inch mount that fits a fritz!box 7530, fritz!box 7530 AX and most likely the fritz!box 7520, too. The tested 7530 and 7530 AX used the newer fritzbox design. Their original casing dimensions are 20.5 × 15 × 4.5 [cm] (L×W×H),…
Wandhalterung für FritzBox 6670; 6591; 6690 um diese mit 2 Schrauben an der Wand zu befestigen. Die Halterung ist für die Wandmontge geeignet mit einem Lochdurchmesser von 5mm und einem Lochabstand von 125mm Drucken im PrusaSlicer: -…
FritzBox 5590 Wall Mount Print recommendation: Infill 25% gyroid / no supports Material: PTEG Happy printing
Wand-/ Halterung für Fritzbx 7530. Habe die Halterung mittels doppelseitigen Klebeband an einer Komode befestigt und die Box eingehängt. Hält sehr gut. Wall bracket for Fritzbx 7530. I attached the bracket to a chest of drawers using…
Here's my FritzBox 6490 Stand, I designed it to have a better cooling for the Fritzbox. For lucky owners of the hot 6490, I would advise switching Wi-Fi overnight automatically off. The alignment issue (which is visible on the second…
I made this in two components, because it would be hard to print otherwise. The “bridge” is just to make it mountable a bit away from the wall, you don't need to print that part if you want to screw it straight on the wall. It was…
Holder to put FritzBox upside down on the wall. You will find many different hole spacings in the stl files. Print like the original with 40% Infill and 3 Perimeters and use organic support for overhangs. Print file is just to show the…
In der Scheune wird es im Sommer zu warm und die Fritzbox hängt sich auf, daher nun eine Variante mit Lüfter, welcher vom USB betrieben wird. Mit genug Platz für Luftzirkulation sinkt die Temperatur drastisch. Lüfter ist seitlich versetzt…
Printed with a 20% infill Device is designed to press fit into the bottom of a fritzbox family of routers. I used double sided tape to attach to my wall
This is a simple tool to fix your FritzBox7560 under a table. You will need 2 of them. I'm using the version without holes, but there is a second version with 5mm holes. You may turn two additional pieces by 180 degree, and you will have…
Enhance the aesthetic of your AVM FRITZ!Box 6690 with our custom-designed cover! This stylish and functional accessory is crafted to fit your device perfectly, providing both protection and a touch of personality to your home or office…
Practcal Wall Mount Kit for securely fixing your fritzbox on any surface or at the wall.
FRITZBox! 7490 distance wall mount Have Fun, don´t hesitate to give a like or post a make picture. Open for any improvement ideas.- just send me a message. Category: Office
Part Description ESRack Module for the Fritzbox 6690 Cable. Uses 2U Possible Configurations: - [Mounting Bracket Short] + [Module] + [Module] + [Mounting Bracket Short] - [Mounting Bracket Medium] + [Module] + [Mounting Bracket Medium] -…
This is one of our organizer for buzzbox in VW ID.Buzz middle buzzbox. This one has three compartments.
Parametrizable 10 inch and 19 inch rack mount for - FritzBox 6590 and 7590 - Netgear GS316 / MS316 and GS308 / MS308 Screw size is parametrizeable, example is with M4 10mm screw Source at Github https://github.com/bobosch/RouterRack
Fritz!Box Wallmount Cover This Cover will hide your Fritzbox or other Router/Modem of your choise if you mount it on a Wall. This Cover is designed to fit for FRITZ!Box 7530 AX . Other Routers or Models will fit if they have a maximum…
Stand for my FritzBox 7530 AX to keep it at 35° for reduced footprint and better status-LED visibility. There are four notches and two stubs to mechanically interface with the router and hold it in place. On the bottom side there are four…
Fritzbox 6690 10 inch Rackmount with Keystone slots. Use M3 screws for mounting the PCB of the Fritzbox. Several short pieces of transparent filament are used as light guides. The holes for these must be drilled to the correct size so…
2 Höheneinheiten Modell muss wahrscheinlich im Slicer geschnitten werden. Gedruckt ohne Stützen
Unser Haus wurde mit FTTdp (firbre to the distrebution point) ausgestattet. Mein Provider stellte mir ein FTTdp Modem das nun zwichen den Router und dem Anschluß geschaltet werden mußte. Da der Platz an der Wand langsam knapp wurde habe…
Printed with PLA+ 50% infill 0.28 layerheight The model has cutouts for 3 rubber feet each piece (6 x 2mm) → https://www.amazon.de/dp/B0CZ74H8HY?ref=ppx_yo2ov_dt_b_fed_asin_title
The FritzBox 4040 is primarily designed for placement on a desk or wall mounting, making it challenging to mount upside down, such as under a desk. My design utilizes the two existing wall-mount holes and adds additional support at the…
A neat outdoor housing solution for a FritzBox FRITZ!Powerline 1260E WLAN Repeater to extend Wi-Fi to the Garden or Roof Terrace. Print each piece, and assemble as seen in the photos. The All-Weather box used was purchased on Amazon here:…
A while back, I upgraded the networking setup in my loft, replacing the old Fritzbox with a Vigor router, OPNSense firewall, HPE Aruba switch, and a few OpenWRT access points. However, I kept the old Fritzbox as a backup. Recently, I…
This is one of our organizer for buzzbox in VW ID.Buzz middle buzzbox. This one has two same compartments.
Hy EDIT: added additional screw holes to mount the Firtzbox downside, please give me feedback if that works, because I didn't use it. Added because the Antenna is original on the backside also added TPU feet so it doesn't slip I designed…
FRITZBox! 6850 distance wall mount Have Fun, dont hesitate to give a like or post a make picture. Open for any improvement ideas.- just send me a message.
This is a small device to monitor my internet connection. It shows the currently used bandwidth in MB/s for the upload and download (in the sample image it's 410Kb/s uploading and nearly 18Mb/s downloading). I use it to see directly if…
I just made the adapter so the distance is bigger and I can mount my FritzBox 7490 on top. Other parts are from “dustybrother”. (See Remix) Just print and glue between the two parts. Print Instruction 0.25mm DRAFT Setting for PrusaMINI in…
A holder to attach a DIN rail to the back of a FritzBox 7583. The 7583 has a very odd shape with a big cutout in the back, making it protrude quite far from the wall. To reclaim this lost space and to better organize my Raspberry Pi…
Fritzbox 6591 10 inch Rackmount with Keystone slots. Use M3 screws for mounting the PCB of the Fritzbox. Several short pieces of transparent filament are used as light guides. The holes for these must be drilled to the correct size so…
Pflanzbox für Aufzucht der samen oder jungpflanzen! Es kann mit erde oder nur mit wasser die aufzucht begonnen werden ! Es sind zwischen boden und pflanzpöttchen 2cm platz so das die wurzeln auch ohne erde bewässert werden können. Ich…
Vertical stand for Fritzbox 7510. Use supports for overhanging structures, print with any material.
Mounts with two 4,5mm Screws.
This box has three compartments for “1” coins for “5” coins for pirate tokens It has a sliding lid and is 41,5mm to let you keep the centre tile of the game below this box (see pics). Have fun! Dimensions (WxDxH): 92,5 x 92,5 x 41,5mm…
You will need to disassemble the Fitzbox first. Two screws are below the rubber feets, we careful not to miss them. PCB of the Fritzbox can just be put into the printed mount. I used 4 M3 heatset inserts in the corners and 4x M3x12 screws…
Als Lüfter verwende ich einen 140er Standard PWM-Gehäuselüfter von be quiet! Diesem habe ich einen USB-Stecker angelötet, der direkt von der FritzBox versorgt wird und somit mit 5Volt betrieben wird. Die Funktion von Lüftern die nicht…
I bought a used FritzBox 7590 to enhance my home network. The mount for my 5690 fiber was too big and needed some remodeling. The idea of the mount is to have the connections accessible from above. It is also possible to put it under a…
Ständer für verschiedene Fritzboxmodelle. Breite und Höhe kann auf das jeweilige Modell angepasst werden. Zur Befestigung der Box auf dem Ständer werden noch 2 Holzschrauben 2x15 mm benötigt.
Prints with the front face down with no supports, but will need to be cut in half to fit on most 250mm print beds. Rack-mount hole spacing does not strictly match 2u spacing, but this does permit moving it up/down more freely, total usage…
Abgewandelter Standfuß um eine SSD-Festplatte mit anzubringen https://www.printables.com/model/296446-stand-for-fritzbo
Hier eine Möglichkeit Kindern mit Belohnung oder Nichtbelohnung zu zeigen was eben gut oder schlecht war. Wir haben dieses für meine Enkelkinder genommen für die Schule. Meine Enkelin Emilia bekommt nun vom Lehrer jeden Tag eine Münze.…
Einfach über die Lupe stülpen und es gibt keinen Staub auf der Linse. Kann mit Deckel auch zum sicheren Transport verwendet werden. Filament: Case PLA Deckel: TPU
If you have VW ID.Buzz and dont know where to put tickes, you need this ticket holder to buzzbox in middle.
I made a simple cover for the TAE Phone connector. Tested only on FritzBox 7530 AX
A model of a storage box for SMD or through-hole resistors, designed for the E24 series. Print with a 0.4 mm nozzle. The optimal layer height for printing is 0.25 mm. The line width is 0.6 mm.
Fritzbox-Telefonhalterung für das Montieren des Telefons an der Wand mit Dübel. Unten hat die Halterung eine Aussparung um nach der Montage an der Wand das Telefon einfach anzuschließen. 3 Wandlinien 15-20% Infill je nach gewünschter…
This is one of our organizer for buzzbox in VW ID.Buzz middle buzzbox. This one has only one big compartment.
Simple Fritzbox wall bracket. Two countersunk screws 3.5 or 4.5 are required to attach the bracket and two M4 screws with a flat head. Einfache Fritzbox Wandhalterung. Es werden zwei Senkschrauben 3,5 oder 4,5 zur Befestigung des Halters…
Das ist ein Regalhalter für Fritzboxen mit 197mm Lochabstand. Kein Bohren und Dübeln nötig. Die Schraube ist M4, habe das Gewinde geschnitten, sollte aber auch durch Eindrehen der Schraube funktionieren oder Gewindeeinsatz einschweißen.…
simple feet for Zotac CI320 NANO require m3 8mm screw DIN965
Münzbox für Schweizer Franken + Rappen. Meine Druckparameter: PETG 0.2 Lh Infill: 15% Stützen: überall Drucker: Prusa XL
Two-part sliding mount for Fritzbox routers
This is a Server Rack Case for a FritzBox 7590 AX v2 and a Raspberry Pi 4 All Netzwork Connection getting passed through to the front. with Keystone Female to Female connectors.
I have installed a Fritzbox 7530 in my attic to supply the upper floor with WLAN (Lanbrücke / plasterboard ceiling). Unfortunately, it can happen that the temperatures there can rise well above 40° in summer. The Fritz! box doesn't like…
Compass replacement Box: for Kern and Migros - shockproof / shatterproof B50 - Slim - 50 x 185 x 20 / Sanding Paper Zone - 38x160 B53 - Med - 53 x 185 x 20 / Sanding Paper Zone - 40x160 B65 - Large - 65 x 185 x 20 / Sanding Paper Zone -…
It’s a hot summer and even the Fritzbox is working up a sweat. I still had some pengda 4020 12V 3D Turbo radial fans left over, which can be powered by the Fritzbox’s 5V output. Unfortunately, you’ll have to sacrifice a standard USB cable…
Here is a little riser for my Fritzbox the Plan was to get a proper position for it on my Ugreen 2800 NAS instead of just putting it on top with this riser the Fritzbox will be a bit cooler and the NAS as well You can use this on a NAS or…
