Liczymy pasujące modele…
This collection comes with plates made specifically to mount inside the ZOHD Nano Talon fixed-wing drone. They can be remixed to fit any flight controller combo but are made specifially to fit a Pixracer flight controller, a generic M8N…
Simple print using PLA. Bed temp 60 C., Nozzle temp set at 200 C. for the filament I was using.
An effective solution for mounting the model on a wall to protect it from damage from constant folding and unfolding. The thick walls perfectly support the load, even with the battery charged. I printed with PETG, but PLA should also do…
So there is multiple versions: Blank Version 20mm Camera Mount Version 20x20mm VTX Mount Version CAM + VTX Version STEP files of the blanks so you can customize your own ;) A 1.8mm 1.2mm Wall thickness Version. Would recommend 1.8mm for…
Just designed to replace the stock stick on one by being removable. No antenna holder, etc - just a cover. With good cooling on the overhang you should be able to print without support, otherwise use tree supports.
This is a simple model of the interior of the extra electronics bay in both wings of the Zohd Altus twin engine foam RC aircraft. Insert and affix with tape to make the wings more streamlined. The original FreeCAD model is included.
Quick little fix for my Zhod Drift, uses 3mm coroplast as the fin and a bamboo skewer as a joining pin
ZOHD Altus nosecone Adapted from Hybridkunst to precision fit DJI Air 03 system. (Model4_Final.stl) DJI 03 Air mount the fan for ZOHD_lid.stl - (Tap M3 threads for 30 x 30 x 10 5vdc fan into lid, use M3 * 14mm screws to mount Fan to lid)…
Assembly instructions: Tap M3 threads into holes into fan mount holes on lid or use self-tapping screws M3 * 14mm to secure 30 x 30 x 10 5Vdc fan to lid. Secure FAN to lid. Tap M3 threads into receiver holes on base for the lid or use…
This is a DJI Vista mount I made for the ZOHD Drift. It replaces the GPS canopy, works great for keeping the CG where it should be and the vista gets plenty of airflow to keep cool. I have this setup with a pan servo right in front of the…
These are as close to 1:1 as I could do, with a few minor tweaks to make them lighter, they're very close to the original's weight, but are stiffer. They were made in Ondsel/FreeCAD. Use an M3 threaded insert for the wing brace. I printed…
I did not found so much support for ZOHD DART XL with O3 airunit. then I designed mine which is lightweight, based on existing front plate. I glued it , and fine tune the camera hole to allow up and down tilt. 2 holes have been done on…
this servo horn adapter works with most servo horns, making it possible to use any type of 9g servo in Vtail of Altus
a simple mount for the SMO 4k to be able to mount it on a ZOHD Drift
Features: Lightweight design Accommodates SMA pigtail with or without base Rear mounting hole for single M2 attachment screw and anchor nut Hexagonal holes for cooling Hardware: 1× M2x4 screw (rear mount) 1× SMA base plate with 2x M2…
added screws for main unit and slot for sd card, some re-positioning of the camera, all credits to the author of the oryginal design - thank you for sharing f3d! Category: Hobby
A complete nose for the Dart XL including mout hole for micro cam 19x19 and a Vista (V2) The V3 can support all types of cameras up to 21mm (with washers if necessary). Two holes on the sides allow access for a screwdriver. And it's a…
Modified the original model for more space in the interior. Also, added a pier for the Runcam Thumb that can see over the antenna for the VC400.
My friend lost his ZOHD Drift's front canopy– so I designed him one to be 3D printed, obvi The original one, even when printed with 1 perimeter and minimal infill, was still far too heavy and so strong it was vast overkill. So I…
Tail-boom repair collar works great when your drift carbon fiber tail snaps. The horizontally printed collar is crazy strong, prints without supports, and flies great. Glue it together with hot glue. Yes, in my testing hot glue is better…
Destroyed my ruddervators during a flipped launch and subsequent crash. This file replaces the foam ruddervators. File is for the right side ruddervator, mirror the model in slicer to get the left side. Print vertically. I used these…
ZOHD Altus – Magnetic Nose for Walksnail Moonlight This 3D-printed nose is designed specifically for the ZOHD Altus FPV aircraft. It provides a dedicated mount for the Walksnail Moonlight unit (camera + VTX) and attaches magnetically to…
I didn't want to mount the GPS outside so I made s simple mount to place a GPS inside the fuselage of the Dart 250g. The mount is affixed with approximately 1mm width double sided gummy tape. It's little bit of snug fit across the…
I wanted to be able to mount batteries without hook and loop fastener, so I made this battery tray. It's affixed to the fuselage using double sided gummy tape that's approximately 1mm in width. This gives enough space to flushly run a…
ESC cover for the Dart250G with intigrated antenna mount. Glue in the 3D printed nuts and you can remove it any time.
Battery mount for the Dart 250G to use velcro battery strap and simple adjust the COG.
Simple mount for many flightcontrollers with standart 25x25mm mounting holes like the Matek F405WSE.
wanted a new aerodynamic nose with an integrated camera mount Untested +5 -15 degrees camera tilt Print Settings Printer Brand: Bambu Lab Printer: A1 Mini Rafts: No Supports: Yes Resolution: 0.16 Infill: 100 Filament: something strong…
Holds an O3 unit, Use the IFlight O3 heatsink: https://shop.iflight.com/DJI-O3-VTX-Heatsink-Pro1915 Should fit other wings Glue it and fiber tape it The camera hole will need to be opened up Print Settings Printer Brand: Bambu Lab…
Covers up the front gopro hole if you dont run a gopro Print Settings Printer Brand: Bambu Lab Printer: A1 Mini Supports: Yes Resolution: 0.2 Infill: 100 Filament: ESUN TPU Category: R/C Vehicles
Wallmount for ZOHD Dart 250G. The gcode is sliced with manual filament change, if you have an MMU you can slice it yourself. Print it with or without TBS logo.
With the planes design you are kind of locked into buying their motor if you have any issues with it. This adapter plate allows you to push the prop back into some cleaner air and also you are able to use any 19mm diagonal bolt pattern…
Simple print using PLA. Bed temp 60 C., Nozzle temp set at 200 C. for the filament I was using.
An effective solution for mounting the model on a wall to protect it from damage from constant folding and unfolding. The thick walls perfectly support the load, even with the battery charged. I printed with PETG, but PLA should also do…
So there is multiple versions: Blank Version 20mm Camera Mount Version 20x20mm VTX Mount Version CAM + VTX Version STEP files of the blanks so you can customize your own ;) A 1.8mm 1.2mm Wall thickness Version. Would recommend 1.8mm for…
This is a wall hanger for the ZOHD Dart XL Enhanced (latest model as of Jan 2026). It is designed to be easy to print, minimalistic, and strong. I have tested it to 2kg and it doesn't have any issue holding the plane. The holder was…
Just designed to replace the stock stick on one by being removable. No antenna holder, etc - just a cover. With good cooling on the overhang you should be able to print without support, otherwise use tree supports.
This is a complete redesign of Beetlebeetle's original ZOHD Nano Talon Evo VTX and Antenna Mount . My remix supports any conventional 36mm² size (30.5mm² mounting holes) video transmitter, and a passthrough for a conventional…
Nose Cone Mod for ZOHD Talon GT (Walksnail Avatar GT2 Setup) The mod houses the Avatar GT2 VTX aswell as a 9g Servo to allow a tilt motion while flying. This guide explains how to install a Walksnail Avatar GT2 VTX and camera into the…
This is a simple printable mount that goes inside the fuselage of a ZOHD Nano Talon EVO frame. It is designed to mount a standard 30.5x30.5mm flight controller . I printed mine in PLA PRO and attached it to the frame with a bit of hot…
ZOHD ALTUS nose cone adapted for the Walksnail Avatar GT2. I have added a cut-out for easier access to the SD card. The camera has a small amount of tilt adjustment, and I have also added locking screws for the antennas, allowing their…
Front top canopy for Zohd Drift rc air plane. Print at angle with brim, 2 perimeters and zero infill: I made square hole for magnet. Glue it with CA or epoxy
Mount for nano sized cameras for the ZOHD Dart250. Friction fit to the fuselage. Needs to be rotated slightly to match the printbed.
This is a rear lid for the ZOHD Dart 250. It fits an FrSky R-XSR and a TBS Unify Pro HV Race 2 including the corresponding antennas. With the heatsink of the VTX in the airflow it should not be able to overheat.
I made those objects to upgrade my ZOHD Nano Talon with a iNav powered flight controller. There are three objects: FC mount which fits the Omnibus F4 Top plate for the TBS Unify antenna Bottom plate for the TBS Unify Print Settings…
This is a mount to place in the belly of the ZOHD Nano Talon RC Airplane, and hold a GoPro Session or similar RunCam device. This makes use of the wooden bar and screw hole that are in the belly compartment, and would normally hold the…
Mount for the ZOHD Dart250g to carry both an FPV cam and the Insta360 SMO 4K cam on the nose of the aircraft. SMO cam mounts with an M3 bolt and nut. Removable even if camera mount is glued to the aircraft. FPV cam mounts with normal…
Includes: Rear Hatch with a slot for the TBS Unify Pro32 HV and an MMCX 90 degree Antenna, such as the Foxeer Lollipop 20x20 M3 glue- (or velcro-)on stack mount (I use a Matek H743-mini V3) 14mm camera canopy (tested with the Caddx Ant)…
The parts were printed with PETg and the sideplates were fixed with double sided tape to the fuselage. The antennas lays flat against the foam of the fuselage and they are not able move in flight. The hatch closes without cutting any…
Bought a new motor but the motor mount hole spacing was off so designed this motor plate. i extended the motor out 3mm to quieten the prop noise. Printed in PLA, can be printed in anything rigid.
This is a mounting bracket/ clip for the ZOHD VC400 piggyback camera. This allows the camera to be snapped into a bracket or easy removal later. The mounting bracket also has an air scoop as this camera gets HOT during use. This is…
I wanted a clean way to mount the VTX and Antenna on my Nano Talon Evo. These parts mount to the underside of the nose/canopy lid and are out of the way of the battery etc. You'll need to cut a 17mm hole in the lid for the antenna mount.…
This hatch is locked with spring loaded canopy lock from MP JET part no 2661 (Ø 4.1mm x 10mm) Just print both parts, load canopy lock (no need for glue) cur some foam and glue pieces.
Mount your VTx antenna on front canopy and get your underneath VTx ventilated.
Antenna mount for ZOHD Drift. The mount takes a pig-tail that comes with most VTX's and mounts it solid in the plane. You need to cut a hole in the plane to fit the mount. The thin sheet will add some additional structure to the area to…
Needed an antenna mount, due to the fact that I was not able to get the long Antenna or an extension. So I designed this little mount. You will need a hole for the Antenna cable and two holes for the guide pins. Glue them to the case,…
Wanted to create my own design, cause all I found was not stable enough and therefore I don't wanted to cut a hole in my Dart250 cover. My version does not really differ from others, but has a collar at the edge to fit better. This is…
I use a Matek F411 WSE and a Caddx Vista, and fly a 4s 850mAH battery in my ZOHD Dart 250g. I try some variants to put all together and get the CG in the right position, but nothing satisfied me. So i build a Mount for the FC and the…
This Design is inspired from Painless360s Antenna Mount, Name "ZOHD Dart 250G Antenna Support", ID 4726331. As Painless 4mm Antenna Mount don't allow remixes, it's completely self designed for a Caddx Vista Antenna with 3mm Dia. Category:…
This is a reinforced firewall for the ZoHD Dart XL Extreme. It has the trust angle correction already implemented. To install it, remove the original firewall. Make some holes with a sharp knife on the position of the "spikes". Put some…
An almost identical copy to the balsa base plate for the battery bay of the Talon Evo
This is a DJI O3 Cam Mount for the ZOHD Dart250g. Print in PLA with no supports.
the vtx is a VT5804 NANO VTX from panda rc (400mw) the gps is a TBS GLONASS but a BEITIAN BN-220 GPS also fits vtx is mounted with 2 servo screws After I have screwed it to the plane I have glued the 2 sides to one another with super…
A simple "adapter" to mount 24mm flight controllers to the wood inside the ZOHD Drift. I designed mostly for my MatekSys F411-WSE flight controller, but there is a "universal" one as well. I mounted mine to the bottom (as there was more…
To assemble it will require zipties and 4 small screws (or some glue if you have no screws), but nothing else. It fits into place. Camera angle adjustable. Integrated antenna holder (zip tie to the little thing on the top of the AU back…
Insta360 Go2 with power adapter mount for ZOHD Dart XL. For use, you also need the HGLRC Tuning USB adapter.
This is a lightweight camera mount for the ZOHD drift that attaches to the top cover. It is only 2g and uses a zip-tie to secure the camera into place. I have flown with this camera for many hours, and not had any issues with the camera…
Just my design to enable digital fpv experience for my little dart rc plane :) Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 30 Filament: n/a petg Category: R/C Vehicles
Mount to fix the HD Walksnail Avatar HD Pro camera (19mm). 4x M2x4 screws to attach camera.
