CoralBoard SL Mount | VESA 75 + Wall + Desk Stand | Screw-Free Snap-In
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
One plate, three ways to use your Synaptics Coralboard SL: behind a monitor (VESA 75), on a wall (keyholes), or on your
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 0
- Makes
- 0
- Views
- 11
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Computers
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Development boards usually end up loose on a desk, held by their cables. A bare Coralboard needs a mount that works wherever the project goes: on the back of a display for a demo, on a wall as a smart-camera node, or standing on a desk for development. This plate does all three with the same printed part. Because there is no case, nothing covers the USB, microSD, GPIO, camera and display connectors, the M.2 slot or the battery connector.
Features
Snap-in board retention, no screws: four flexible corner arms with hooks click over the PCB corners. Pull an arm outward to release the board.
All ports open: there are no walls around the edges. The top side stays free for camera and display cables. The bottom side has 11 mm of standoff clearance and a 56 x 40 mm window for cooling and for bottom-side parts.
VESA 75 x 75 pattern (M4) with counterbores, so screw heads sit below the surface.
Wall mount: two keyhole slots, 50 mm apart.
Desk stand: two clip-on feet hold the plate leaning back 20 degrees. They press onto the bottom edge with a printed friction ridge. No tools.
Cable relief: two tie-wrap slots for strain relief on the USB / power cable.
Fit-test coupon: a small corner piece (about 20 minutes) so you can check the fit with your own board before printing the whole plate.
All parts print flat, with no supports.
Hardware
None required. The board is held by the printed snap arms.
Only your mounting method brings screws:
VESA mount: 4 x M4 screws, length to suit your monitor's bracket.
Wall mount: 2 x wall screws (head up to 8.5 mm, shank up to 4.4 mm).
Optional: 2.5 mm cable ties.
Parts
File | Qty | Notes |
|---|---|---|
| 1 | main plate, flat on the bed |
| 2 | print standing as exported (profile on the bed), only needed for the desk stand |
| 1 (optional) | one corner of the plate: test the board fit first |
Print settings
Printer | Prusa CORE One / any FDM, 0.4 mm nozzle |
Material | PETG recommended (springier snap arms, more fatigue-resistant). PLA works. |
Layer height | 0.2 mm |
Walls | 4 (the arms are thin; more walls make them stronger) |
Infill | 20 % |
Supports | None |
Brim | Not needed |
Estimate (rough, not a slicer result) | cradle about 35 g / 1.5 h, each foot about 10 g / 0.5 h, coupon about 4 g / 0.2 h |
Assembly
Print the fit-test corner first. Hold your board against it: the PCB corner should drop onto the post and under the hook with a small gap.
Print the cradle (and the two feet if you want a desk stand).
Place the board over the posts, components facing up, and press down on one side, then the other. The four arms flex outward and the hooks click over the PCB. To remove, pull each arm gently outward and lift the board.
Mount it:
VESA: screw through the four counterbored holes into your monitor or bracket.
Wall: drive two screws 50 mm apart, hang the plate on the keyholes and slide it toward the slot ends.
Desk: press both feet onto the bottom edge of the plate (feet about 27 mm from the centre) until fully seated.
Use the two slots in the plate with cable ties to anchor your power or USB cable.
Design data and honest limits
I could not open the official reference CAD (the Printables page was blocked for my tools), so the board data comes from published sources. Check it against the official CAD or your own board before printing the whole plate:
Item | Value used | Source |
|---|---|---|
PCB outline | 73 x 58 mm, 1.62 mm thick, corner radius 3.5 mm | a community case design on Printables (Parametrisches CoralBoard SL Gehaeuse) |
Overall size | 60 x 75 mm | DigiKey listing (consistent with the PCB size plus connector overhang) |
Compared to Raspberry Pi 5 (85 x 56 mm) | "more compact" | Synaptics developer blog (consistent) |
Mounting holes | 4 x 3.2 mm at 65 x 48 mm | the same community design only (single source) |
The posts are support only, not pins, so a wrong hole position cannot stop the board from seating.
The arms use the PCB corner outline: if the real outline differs by more than about 1 mm, change the values at the top of
model.py(BOARD_*) and re-run. It rebuilds the cradle and re-checks fit.I do not know where the connectors sit, so I left every edge free. If a connector on the bottom side is taller than 11 mm, tell me and I will raise the standoff.
Software checks done: the board model overlaps the cradle by 0.0 mm3, the hooks overlap a board lifted by 1 mm (so they do retain it), the snap-in arm flex is 1.0 mm with an estimated bending strain of about 1.2 % (OK for PETG and PLA), and the foot clips onto the plate with the intended 0.2 mm friction interference. Not test-printed yet.