Centerlock Self-Centering Vise | Printed Screw, Swap Jaws, Tilt Clamp | No Hardware
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
One handwheel, both jaws move together, so your part is always on the centre line. Fully printed, nothing to buy.
- Rating
- 4 / 5
- Likes
- 18
- Downloads
- 33
- Makes
- 1
- Views
- 200
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Tools
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Centerlock is a small bench / desk vise built around one idea: self-centering. A printed double-ended screw (right-hand thread on one half, left-hand on the other) drives two half-nut carriages in opposite directions, so both jaws always close on the same centre line. Round rods, tubes, PCBs and blocks sit dead-centre without nudging them.
The thread is a 2-start, 8 mm lead per jaw: 16 mm of opening per handwheel turn, so you can go from fully open to clamped in under 5 turns. The jaws are swap-in dovetail plates (flat with TPU pad, 90° V-groove for round stock, PCB slots) that drop in from the top. The screw and carriages also drop in from the top (no sliding assembly), and the whole thing is held together by geometry only: no screws, no magnets, no springs, no glue.
An optional desk clamp with a printed ball head lets you tilt and swivel the vise, and slide it on a dovetail to balance heavy work.
Features
Self-centering: one screw, left/right-hand threads, jaws always symmetric about the centre line
Fast: 2-start thread, 16 mm jaw gap per turn, 0 to 76 mm opening (flat jaws)
Swap-in jaws: flat + TPU pad, V-groove (rods up to ~25 mm, auto-centred), PCB jaw (1.0 / 1.8 / 2.6 mm slots)
Engraved scale on the deck (tick every 5 mm of jaw opening)
Drop-in assembly: body, then screw, then carriages, then jaws. Disassembles the same way
Handwheel on one end and a knob on the other: turn it from either side
Ball-head desk clamp: Ø32 ball, ring-nut lock, tilt + swivel, dovetail slide, fits tables ~5 to 50 mm
Every part prints flat without supports, in PLA; TPU for the grip pads (optional)
Print settings (Bambu Lab, 0.4 mm nozzle, PLA)
Layer height 0.2 mm, walls 4, infill 15 % gyroid (screws and carriages: 25 %)
Supports: none. Brim on the screws (they lie on a 5 mm wide flat) is recommended
Keep the orientations in the STLs (they are already print-flat). The screws print lying down on purpose, so the threads are round and the layers run along the shaft
Slow the outer wall to ~60 mm/s on threaded parts (screws, carriages, clamp frame, ball head, collar)
Estimates (rough, not slicer results, 15 % infill): see the parts table
Parts list
File | Qty | Colour idea | Est. g | Est. time |
|---|---|---|---|---|
centerlock-vise_body.stl | 1 | graphite | ~108 | ~4.8 h |
centerlock-vise_screw.stl | 1 | light grey | ~22 | ~1.0 h |
centerlock-vise_carriage-a.stl / carriage-b.stl | 1 each | orange | ~21 each | ~0.9 h each |
centerlock-vise_handwheel_x2.stl | 2 (vise + clamp) | orange | ~21 each | ~0.9 h |
centerlock-vise_end-knob.stl | 1 | graphite | ~10 | ~0.4 h |
centerlock-vise_jaw-flat_x2.stl | 2 | dark | ~12 each | ~0.5 h |
centerlock-vise_jaw-vee_x2.stl | 2 (optional) | dark | ~18 each | ~0.8 h |
centerlock-vise_jaw-pcb_x2.stl | 2 (optional) | dark | ~13 each | ~0.6 h |
centerlock-vise_tpu-pad_x2.stl | 2 (TPU, optional) | black | ~2 each | ~0.1 h |
Desk clamp (optional) | ||||
centerlock-vise_clamp-frame.stl | 1 | graphite | ~66 | ~3.0 h |
centerlock-vise_clamp-screw.stl | 1 | light grey | ~13 | ~0.6 h |
centerlock-vise_ball-head.stl | 1 | orange | ~27 | ~1.2 h |
centerlock-vise_ball-collar.stl | 1 | graphite | ~20 | ~0.9 h |
centerlock-vise_tpu-disc_x2.stl | 2 (TPU, optional) | black | ~1 each | ~0.0 h |
Vise only (flat jaws): ~230 g, roughly 10 h of printing. Everything including clamp and all jaws: ~420 g.
No extra hardware needed.
Dimensions
Vise: 162 x 67 x 62 mm (jaws up), plus handwheel (Ø58) on the right and knob (Ø36) on the left
Opening: 0-76 mm flat jaws, about 0-55 mm V jaws, 0-74 mm PCB jaws. Jaw plates are 58 wide x 30 tall
Jaw travel: 16 mm of gap per turn (2-start, 4 mm pitch, Ø14 screw)
Desk clamp: 66 x 146 x 23 mm frame, jaw opening 56 mm, ball Ø32. The mount slides in the dovetail on the underside of the vise (24 mm mouth, 4 mm deep)
Assembly (about 2 minutes, no tools)
Lay the body flat. Drop the screw in from above: its two collars go into the slots in the end blocks.
Drop each carriage in at the centre notch (the "gate" in the middle of the body), over the screw. Turn the screw slightly until the teeth mesh, then slide the carriage outward: the rails on its legs lock into the grooves in the body.
Press the handwheel onto the square end of the screw (right) and the knob onto the left. They are a snug press fit with small crush ribs.
Slide the jaws down into the dovetail slots in the carriages. Press a TPU pad into the pocket of the flat jaw.
Turn the handwheel clockwise to close the jaws, counter-clockwise to open them. If it is the wrong way round on your print, you mirrored something: both carriages must be on the correct side (carriage-a on the handwheel side).
Desk clamp: thread the clamp screw into the frame from below and press the second handwheel on. Slide the ball head onto the dovetail on the underside of the vise, drop the vise's ball socket over the clamp ball, then screw the collar on from below until the ball holds. Tighten by hand to the friction you want.
Fit-test coupon (print this first, about 30 g and 1.5 h)
Folder fit-test-coupon/ has four tiny pairs that use the exact same geometry and clearances as the real parts. Print them with the settings above (same filament, same slicer profile) before committing to the 10 h vise:
Pair | Files | Pass if |
|---|---|---|
1 Thread |
| The screw lies in the half-nut and turns by hand with a little drag, no wobble. Binds: raise |
2 Handwheel |
| The tang pushes in with firm hand pressure and does not fall out when held upside down |
3 Jaw slot |
| The tongue slides down the dovetail with light pressure, without play |
4 Rail |
| The saddle slides along the body slice smoothly, and cannot be lifted off |
CAD check of the coupon pairs: thread, jaw slot and rail overlaps are 0.0 mm3; the handwheel pair has only the intended 7.9 mm3 crush-rib interference. Regenerate with coupon.py. The ball head and collar are not in the coupon (too big); if you want that tested, print just the collar and ball head after the thread passes.
Honest notes (read before printing)
This is a design from CAD only: I have not test-printed it. The thread clearance (0.3 mm radial and 0.3 mm axial on every nut), the handwheel press fit and the ball-lock friction are the three things to check on your printer. Print the fit-test coupon first (section above).
Screw thread is trapezoid-ish with a 26° flank and 1.8 mm depth, printed lying down so there are no steep overhangs. If it feels tight, scale the carriages 101 % in X/Y or re-run
model.pywith a largerax_cl.The screw sits at the bottom of the vise, so the clamping zone starts about 10 mm above the deck and the screw is exposed between the jaws.
The ball lock is PLA-on-PLA friction. It is fine for electronics, PCBs and modelling; for heavy filing, use the clamp without tilting or lock the ring-nut tight. A strip of TPU between ball and cup improves grip.
The body is heavy (~108 g). That is deliberate for stability; use 10 % infill if you prefer.