Counting matching models…
Thanks to Lukass for the great wind turbine. The wind turbine turns very well. An (Brass) axle 4x190 mm, 4x ~ 80 mm and a screw M3x6 are required. Drill out the bearing blocks with 4.2 mm. Drill out the cross hole of the conical disk with…
Thanks to vladua for the great wind turbine. I enlarged the wind wheel to a diameter of 170 mm and a height of 196 mm and adapted it to my proven bearing for an 8 mm metal rod. The wind turbine parts can be put together without reworking,…
Thanks to rosch8 for the really great original wind turbine. After the original wind turbine had been running without any problems for some time, I wanted to make it bigger. Increased the hub, rotor blade and spinner to 150% and changed…
Thanks to benkrasnow for the original Vortex tube and Hannes_v_d_B for the changes. In the vortex tube, compressed air is brought into opposite spiral movements at high speed. This causes the air to split into a warm and cold air stream,…
Thanks to cooasty for the beautiful pinwheel. The two propellers are counter-rotating and have a nice "hypnotic" effect due to their shape. After cooasty's windmill had survived a few years and storms, I wanted to build the windmill…
Thanks to Rolfiklein for the IBC adapter. I inserted an outer contact surface for an O-ring 45x5. Then the O-ring can no longer slip under the thread Printed with PETG
Thanks again to rosch8 for the great original wind turbine! I've already done a few remixes, this rotor blade design achieves very impressive speeds. I added a second counter-rotating rotor to my remix. Of all my wind turbines, I like…
Thank you airfish for the beautiful counter-rotating illusion wind turbines. I couldn't find the original pinwheel anywhere anymore... I enlarged the wind turbines to 200 mm and added hubs for ball bearings 608ZZ (22x8x7). There are 4…
Thanks to astfaellergerald for the Vertical Windturbine Ver. 2. I like version 2 (NEW P1-5) by astfaellergerald very much, but cleaning and gluing all the parts takes some work. I've been contemplating putting the top and bottom halves…
Thanks to LegoRJ35 and strikingfpv for the toroidal propellers. Made it into pinwheels with 200 and 250 mm diameter and a hub for 608ZZ (22x8x7) ball bearings with a nice illusion effect. There are 12 different wind turbines with 3x, 4x…
Thanks to Victor for the great Solder Scroll. In the original the drive rollers have different diameters, but the gears give them the same speed. This causes a drive wheel to slip. I removed the gears, widened the rollers and inserted a…
Over 90 modified and new parts made. First of all, a big thank you to Matt The Printing Nerd for the really great project THE 100 and The Forgetfull Dev for the outstanding construction documentation. In the original, the X and Y motors…
Thanks to vladua for the great wind turbine. https://www.thingiverse.com/thing:3627007 I wanted to have the bearing completely below the wind turbine. To do this, I enlarged the bars at the top and bottom and added 8 mm holes. I added a…
Thanks again to Lukass for the great Archimedes wind turbine. For my second remix, I used the original size of the Archimedes spiral and created a new frame with ball bearings and five different sets of tails. It turns even with barely…
Thanks to ArtSuzhou for the great broom holder. The 23.5 mm broom handle fits perfectly in the medium TPU gripper, but the gripper snaps shut again when removing the handle. I made a remix where it's a bit better; if you press slightly…
Thanks again to rosch8 for the beautiful original wind turbine. I recommend printing the successor, the MK3. The bearings on the MK2 wind turbine are difficult to install without causing binding, and temperature fluctuations can also lead…
Thanks to Lukass for the great wind turbine ... After the blue wind turbine broke on the struts in a gust of wind, I reinforced the rotor. The reinforced version has also weathered storms. For my installation situation I changed the…
Thanks to rosch8 for the great original wind turbine. I took the rotor blades from the original wind turbine and modified them. Made the wind turbine smaller, it's 160mm in diameter and 175mm long. A 0.3 mm nozzle would be recommended for…
Thanks to Evocato for the great turbo! The turbo runs with surprisingly little vibration. At 12 V, the turbo can achieve up to 20 mbar at zero delivery. The turbo delivers approx. 440 liters per minute including a 45 cm long ID 18 mm CPAP…
This wind turbine is a remix of https://www.printables.com/de/model/785427-illusion-windturbine-200-250 https://www.printables.com/de/model/782829-windturbine-mk2-neo-remix…
Thanks to Victor for the great Solder Scrolland TactfulElf for the Remix. Now with two ball bearings, optional PTFE, funnel for solder, downward coil, left and right handed, reinforced and RH version from Luer lock. I printed my first…
Thanks to leositu for the bracket and component cooler. This is a collection of parts for modifications to the X5SA. Installed a Volcano nozzle but continue to use the original cold end. To do this I modified the holder and cold end fan…
Thanks again to rosch8 for the great wind turbine! After a single bearing for the rotor worked well on some of my wind turbines, I changed the bearing on the MK3. The new rotor is screwed to my neo wind turbine with an M8 threaded rod.…
Thanks to jpdesign for the StabiloBoss holder. I expanded the holder to 10x, looks great. Update: I also made 4x and 6x holders. The original holder is 8x.
Big thanks again to rosch8 for the brilliant original wind turbine! With these parts you can convert the MK2 wind turbine into a double rotor in opposite directions. The M3 screws for the rotor blades are screwed directly into the…
First of all, big thanks to SunShine for the outstanding idea of printing multicolor / multimaterial filament yourself. Since the bed on my first printer was too small, I reduced the 200 mm filament spiral to 168 mm and 16 grams. It was a…
Thanks to Dsk001 for the beautiful case and Matt The Printing Nerd for the great THE 100. I added the holder to the Frame Connector Front 1 for THE 100. The holder on the connector now has a hole for M 3 BOM heat inserts. On the hinge I…
Many thanks to GabQ2 for the great original cyclone. The cyclone works flawlessly for woodworking; hardly any dust makes its way into the vacuum cleaner. Most other cyclones are mounted on top of the lid, creating a risk of them breaking…
I didn't find a normal Euro beer bottle in Printables, here it is... ;-)
I don't like the original spool holder, you need two hands to slide the filament spool on and off, and spools with larger inner diameters fall off. This spool holder uses the original axle. Pry out the original axle with two screwdrivers,…
First of all, a big thank you to ShelbyCob for the excellently designed top cover. This top cover is my favorite of all, the front flap locks into two positions, and the fit to the printer is perfect. With other top covers, you have to…
First of all, a big thank you to Matt for the outstanding development work on the world's fastest printer (accelerated by Volgger to WR), the T250. On the T250, the four legs are so high that not everyone can print them. I split the legs,…
Thanks to Merkaba for the parts cooler. When the 5015 fan runs at 50%, it cools better than the original fan, and not just from one side. I slimmed down the holder and put it closer and higher to the stepper. The fan connector is now…
Thanks to Robert G, Schrittmotor, alexsnigir and CSD_Salzburg for the original parts. Deburring holder for GRATTEC handle with blades Meter stick holder for a 1 m meter stick. Battery screwdriver holder for WIHAzai House for Skadis and…
Wall mounted box for safety glasses. The lid stays closed due to its own weight and the safety glasses. The lid has an end stop when opened and therefore does not fall down. Several boxes can be mounted on top of each other to save space,…
The holder is for a 100mm long 24V LED strip with a switch. The rocker switch has 8.2x14.7 mm on the mount. I branched off the 24V at the main board fan. The cables are routed upwards in the V-profile and held in place with V-slot strips.…
Thanks to makitprojects and wanderer_76 for the tires. I changed the dimensions of the front tires so that they correspond to 5.5x16 (90x20 mm) tires in 1/8 scale and changed the tread pattern to AS Front. I changed the dimensions of the…
Thanks to theronin for the great box. I cut the box with Tinkercad and put it together larger. Printed with ABS Box 100x60x44 with original lid Box 100x80x44 with lid 100x80 Box 130x60x36.5 with lid 130x60
Thanks to hackerbijey for the great SD card holder. The thread fits perfectly, but I don't like the fact that the cards are clamped to the lid. SD card holder for 9 cards. I added 1 mm of space on the inside of the lid and trimmed 1 mm…
Thanks to Tareku for the PSU case cover. I wanted a case cover without a fan grille—since that also generates noise—and a quieter fan. The mounting position for the 92 mm fan didn't seem ideal to me, as there are no vents in the printer…
Elbows with male and female 35 mm cone The reduction is needed when scaling GabQ2's cyclone to 120.65%. My compatible extraction parts:
Thanks to PROFDM1 for the tractor. I cut a slice from the tractor and tires and added axles for the wind turbine and swivel. 2 mm axles made of stainless steel or brass are required, I used a 5 mm long sharpened piece first in the…
Now you can use Klicky Probe on my THE 100 v1.1.0.1 LW mod. Funkyskull has written instructions on "PCB Klicky Mounts for The100 v1.1". Further information on: https://github.com/tanaes/whopping_Voron_mods/tree/main/pcb_klicky THE 100…
Thanks to Goodcat for the hose connection, the connector fits perfectly. Added a 35 mm cone to the hose connection. And a hose connection with a 35 mm elbow. My compatible extraction parts:
Thanks to CroXY3D and Sivis for the Salfin extruder and Leo DIY for the Volcano holder. GitHub page by CroXY3D: https://github.com/CroXY3D/Sailfin-Extruder The remaining Salfin parts from:…
With these Hoppe door handle bearings, the approaches for the screws tear off after a while. Print this part made of ABS, ASA, PCTG, PETG or similar as hot and slowly as possible. The hole for the door handle must be slightly larger than…
First of all, thanks to Johannes (OMG-3D) for the great push robots. These pushing robots can be controlled from the mobile phone without having to install anything on the mobile phone. You just have to call up the page on the WeMos D1…
First of all thanks to Matt The Printing Nerd for the component cooler template from the fastest printed 3D printer in the world - THE 100. I attached the Creality "High Flow Kit" to the cold end, but not with the enclosed 4.1 mm heat…
Housing 270x120x120 mm for a programmable laboratory power supply. Built in: Switching power supply Meanwell RS-150-15, 199x98x38 mm Controller DPS3012 (others will probably also fit) Axial fan 40x40x10 24 V Power switch Laboratory…
Replacement Control Lever for Lux Tools Cordless Lawn Mower The original lever is manufactured with an extremely thin cross-section at the point where it typically breaks. The original lever is too short, making breakage virtually…
First of all thanks for the great project THE 100 from Matt The Printing Nerd and The Forgetful Dev for the very good documentation https://www.printables.com/de/model/572689-the-100-v11-the-fastest-3d-printer-based-on-a-prin Made a case…
Thanks to stockholmviews I added an M10x1 connection thread with a 4.1 mm through hole. The clamping pieces have a 0.3 mm thick adhesive disk. The PTFE hose connector holds surprisingly rock solidly. The usual compressed air couplings are…
Nozzle box for Creality Ender 7 Spider Hotend High Flow Kit Nozzle Length: 16.8mm Nozzle thread: M6 Nozzle Size: 0.3 0.4 0.5 0.6 0.8mm Lid for: Ender 7 Creality Spider Creality HFK (High Flow Kit) Ender 6 HFK Ender 6 HFT (High Flow…
Thanks to Turbo_SunShine for the great box ...! I figured if the spring loaded gear is on the lid, it doesn't look bad ... As a basis, I used the test part of the original and made a box on it with Tinkercad
Zusätzliche, etwas größere Formscheiben für die emsa Gebäckpresse. Gedruckt mit PETG Additional, somewhat larger shaped disks for the emsa biscuit press. Printed with PETG
Cone Adapter 35 female x 58 male. Suitable, for example, for Metabo band saws and Holzkraft miter saws. My compatible extraction parts:
Thanks to Runfrcover and Franz Josef for the great blast gate. I attached an HT50 male pipe connection on one side and a 38 mm hose connection on the other. You can also combine two HT50 connections or two hose connections. I enlarged the…
With the adapter you can load refills from Recycling Fabrik onto a split empty spool. What is required is an empty spool with the dimensions as shown in the picture. The core is conical, 4 heat inserts M3 D5xL4 and 4 cylinder head screws…
Thanks to Veno_cz for the original hose connection. I redesigned the hose connection as two separate parts. The locking component is printed in TPU A95 and fits onto the connector part; a locking tab prevents rotation. For the TPU part,…
Thanks to ralondo for the adapter. Added a male 35mm cone. My compatible extraction parts:
Protective cap for lance coupling. The Kränzle pressure washer must be laid down during operation, which means the lance rests on the ground, allowing dirt to enter the lance and clog the nozzle. The protective cap is printed from TPU…
Replacement part for a window stay. I printed all parts solidly and bonded the axle in place using two-component adhesive. v2 features a cutout for the pin to make attaching and detaching easier
Hose adapter from 35 mm cone to hose inner diameters of 35, 36, and 38 mm. My compatible extraction parts:
First of all, a big thank to Johannes for the great robots and the excellent building and installation instructions! I used 360° servos and connected them to D2 (left) and D3 (right) on the WeMos. Changed the housings to "DAMPF" and…
I screwed this felling lever holder onto my forestry tool box. The holder is attached using M6 screws.
Chalk holder for marking roads for toy vehicles. Simply attach two holders to the outer tines of the Gardena lawn rake. The holders accommodate 12 mm round or square chalk. The black holder is printed in TPU, and the nut in PLA. The tine…
These are all currently available results.
