Counting matching models…
Repaired mesh iteratively in meshlab so prusa slicer could print it. Will update with photo of print once it is done. Category: Scans & Replicas Note : should print fine in Prusa Slicer after error correction. May not print in certain…
What makes it even better is the source design in FreeCAD :P Print in PETG or ABS/ASA. Category: 3D Printer Accessories
Remixed the Annoying Gift Box by u: LittleCoolBomb : sized in mm. separated the lid from the threaded tie segment. provided split bow for easy, support-free printing. added clearances of 0.3 mm for the tie segments. provided a faster…
Protects your phone and especially the camera bulge in the back against scratches and bumps while allowing the phone to cool properly when charging or in use. Update 4-10-24: added speaker notch; keeping only the camera bulge ring design…
Repair a broken Kohler toilet flush handle system like this https://a.co/d/6Nci2Hg by 3d printing the handle, axle, and angled lever. Must reuse the original through flange. If no longer usable, you can 3d print the square sleeve from…
note: when printing the provided STL use two perimeter lines max so the inner perimeter in the first top face layer doesn't print mid air. Two files are included: Hollow cube customizer / OpenSCAD design STL for 15 mm cube with 8 mm wall…
simple print-in-place hinge to add to other designs It's so simple to print even I could do it, please post makes! :) Print Settings Printer: Sovol SV01 Rafts: No Supports: Yes Resolution: 0.16 Infill: Gyroid 15% (full size), 20% (half…
Just in case yet another 3D scan turn table were needed... here we go. Please observe the CC+attrib+non-commercial license. Don't try and make money off my hard work. If you want to create derivative work I provide the Tinkercad design .…
Works with the 38-mm x 20-mm el cheapo fake tealights. Also check out the original design by u: Perinski . Category: Decor
A 20-mm cube isn't enough to validate your Z-axis steps factor. The calibration should be done with taller test prints or otherwise an undetectable 2-3% error in the height of a 20-mm cube can translate into a very much obvious 2-3 mm per…
Just (another?) TPU bumper case for iPhone 12 Mini. Print with supports -- use either tree/organic supports on buildplate only or the "supports everywhere" option if using regular supports. 0.12 to 0.2 mm layer height. Category: Mobile…
Remix of t: Plain_Seashell_for_Remixing_6232737 by t:u: DaveMakesStuff . Category: Earrings
Introducing the no-frills, no-strings duct your SV01 will become an instant fan of :D. Designed with PETG in mind. A sagging-resistant design, it will not bump into your prints. Minimal path air flow that will not cool the nozzle. Rev.2.1…
Use the color change option in prusa slicer. 1st layer 0.35 mm, all subsequent layers 0.2 mm. Print base in white; first color change at 1.35 mm (black) and second color change at 1.75 mm (orange or red). Category: Earrings
A mount for the ESP32-CAM module case thing:6295703 that slides onto the Y rail tensioner. 12-5-23: added design for SV07+ based on feedback from a maker -thanks! Note: use this camera screw adapter (1/4" 20 tpi) if you have a web cam…
A simple pinecil v2 stand/station without much bells and whistles. For added snap effect you can superglue a 10mmx0.75mm button magnet that will engage with the bottom screw on the pinecil. print with a 0.2 to 0.3 mm layer height, 3 to 4…
(This is the same as original thing 4965384 but reuploaded because it won't get listed on my designs page.) Print flat as shown in the last image. Original source for temples, hinge, and nosepad design is below, included temples here just…
mount a 30 mm axial fan in place of a 40 mm fan. can be used if you want to reuse a 3010 heat break fan with a custom fan mount for 40 mm fans. tinkercad design Category: 3D Printer Parts
Mine broke in a printhead crash. Here's a minimalistic design done in FreeCAD. Airflow goes straight to the nozzle tip where it belongs. Print sideways as shown in the screenshot. Print in ABS/ASA or PETG. Reuse all original screws to…
Print in ABS so it doesn't warp when the oven is in use. (No need for enclosure or draft shield. bed at 80 ºC, nozzle at 240 ºC). Version 2 should provide better grip to the oven door handle. Version 3 is like V2 but reinforced at the top…
A simpler, faster print, without all the hexagons. Use this with the prusament refills. Source FreeCAD design included.
hacked together two existing designs so I can fit a 40x0 heatbreak cooling fan onto my Sovol SV01 printer. also included is a fan guard. 10-23-22: added centered version that works with BMG/Left style extruders on the SV01/03. Print…
Test your bridging/cooling settings! Check if your bed adhesion is good enough for small footprint parts. Prints in minutes and uses less than 1 gram of filament. Category: 3D Printing Tests
The back cover may be needed if the hole in the drywall was poorly done and extends outside of the switch cover. The insert should fit right on and will be held in place by the switch cover screws, just don't over tighten those. Print…
The C270 adapter works with the base, screw and nut from this mount design (thing: 6308788) . Print in the orientation shown in the print bed photo. Update 1-17-24: Revision 1 is slightly shorter in depth so the claw on the C270 can close…
a 3d scan of the left finger cot that comes with the czur aura book scanner. print a mirror image for the right finger cot. the sticker is a scan to scale in 200 DPI of the sticker, should measure 15.5 mm x 20.5 mm. Update 6-18-2026: user…
The stock SV07/plus curtain fan sounds like a jet engine on the runway. It's also not very good at spreading the airflow uniformly. This is yet another attempt to fix that. I drew a lot of inspiration from u:Porpoise Hork 's fan duct…
edited in fusion 360 to hollow out the bottom and extend the lip so as to protect the camera lens. print in a more rigid tpu. Category: Mobile Phone
This mount fits the Pi 3B (v.1.2) without crushing any surface mount components on the board and without impeding access to the Pi camera connector or the GPIO header. Can be used with a 5V Noctua fan powered directly from the GPIO…
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/gsch3ClbLKq Suction cup sucks and won't stick any more. It's also cracked. This mount clips onto the rearview mirror rod and is secured by a M6 screw &…
Print in PETG, ABS, or ASA. 0.2 mm layer height should work. Try 4 perimeters and at least 15% zig-zag infill. Print with supports. Print Settings Rafts: No Supports: Yes Resolution: 0.2 MM Infill: 15% Filament: ANY PETG, ABS, ASA ANY…
Inspired by u: erniec53 's Single-string Tensegrity model, I needed an editable design so I could print the tension brackets flat for better strength. Print Settings Rafts: No Supports: No Resolution : 0.2 mm Infill: 35% Filament : any…
use customizer to adjust size. the STL and default parameters will fit the gear bearing by u: emmett . Print Settings Rafts: No Supports: No Resolution: any Infill: any Filament: any any any Category: Hand Tools
Remixed u:rjm2112's nice design to accommodate a couple more colors. Use a high infill like 70% to prevent infill artifacts from showing on the top surface. Print at 0.2 mm layer height. Color change heights are shown in the slicer…
Started from the awesome design thing:7167040 by u:Mitchiegan but with reinforcements so it doesn't wobble while printing or while using. Print with snug supports with a min supported overhang of 45º or even less and make sure you enable…
Top bracket that's originally made from a crappier material than the lower bracket and shatters if tightened too well. Fits projection type headlight assembly in a 2010 Kia Sedona minivan. Tested the passenger side only. Print sidewise in…
Initially a proof of concept to test my TPU settings, it instantly became my one and only wallet I will ever need. It holds my ID, bank cards, insurance cards, a couple of folded checks, and it's stuffed with cash at the very center to…
A larger stand to accommodate a 15 inch MacBook Pro Retina. Based on idea derived from: Macbook Pro Laptop Stand by jgillick , a rework of Laptop Display Stand (MacBook Pro) by walter (original idea) but designed from scratch in…
The buttons can be customized in FreeCAD via the spreadsheet: diameter, thickness, etc. Values such as feasible hole diameter, feasible hole spread, and feasible fillet radii are then calculated automatically. A 2 hole and a 4 hole button…
When the lid cracks or snaps the contents of your gallon jug may end up spilling when you need to move or tilt it. Duck tape doesn't quite work as a fix. But a 3-d printed lid does. Category: Replacement Parts
Based on Graduation Cap Container / Mortar Board by shrx4me , redesigned larger up to the bed size of a SV01 and for faster print. Notes: due to the large size and the potential for adhesion issues and warping use a wider extrusion width…
Another take on the battery dummy, this time to simplify printing (no supports needed) and save on material. Category: Electronics
Well i needed a simple case for the ESP32-CAM module with slots for both the micro SD card and the LED lamp. It does not fit the USB programmer. But it has enough room for Dupont connectors to supply it with power. Clearance is tight so…
Inspired by thing:3215912 by t/u:AlpoHassinen , designed this 7in x 5in x 5in stand from scratch to fit the 3 liter Kirkland Signature wine boxes that can be found at Costco. Can optionally be used with my other design, the spill catch…
I needed one in 3 colors so here we go. 2 design options for your convenience. Use prusa slicer color change at layer. Use that twice. -Set 1st layer at 0.32 mm, regular layer height at 0.2 mm. -Change colors once at 1.52 mm and another…
If you're like me and always remove the Obama/Biden mandated showerhead flow restrictors that bring marxism into our bathrooms, here's a customizable alternative design in FreeCAD which allows you to adjust the restrictor to your liking.…
Ours has shattered so the only other option was to throw the suitcase away. Preferably print in PETG or ABS/ASA. PLA might still work but it may degrade quickly. Screenshots with a few critical measurements are provided to help you decide…
A nice pedestal holder for the awesome stargate multicolor coasters bu u:Kvant . Provided STL works for 2 coasters. The Freecad source design is parametric and can generate the required design for any (integer) number of coasters. See the…
i like torus shapes lol. v2 is more economical and weird. Category: Organization
Replacement knob. It fits the Bella slow cooker / crockpot / hot pot server pictured below. There are two separate STLs: one is the knob and the other is the indicator dot that you can print in a different color. Source FreeCAD design is…
There is really no purpose to this other than testing your printer on a 3.73g plastic fidget toy. It's a good test for high acceleration in Klipper. The outer perimeter should print in one continuous curve that'll shake your printer like…
Provided here are two models, The first file is just the support that can be added to the Fully Assembled 3D Printable Wrench by barspin in your slicer of choice. The second model is an example that I exported from Prusa Slicer. The…
A remix of the wonderful design Christmas Ball Grinch Earrings by Luc3DPrint: Resized the Grinch's hand to 150%. Converted to single body, multiple layer height for pause for filament change prints. The screenshot serves as a guide for…
print in spiral vase mode and test whether your part cooling is adequate for single perimeter overhangs Category: 3D Printing Tests
A modification of Oster Blender Bottom supported (v2) by SmilingImpact to fix a couple of minor things: slight change in the slope of the conical hollow to be able to support the topmost circular perimeter of the hollow (a couple of lines…
It allows you to remove the spool holder and mount the filament sensor on top of the gantry beam. Update 12-18-2024 : version 2 is a snap mount secured by the stock M4 screw in the back of the top gantry replacing the stock filament spool…
Guides and clamps for the Sovol SV-07 print head ribbon cable. The cable will be routed in front of the gantry and not through the gantry. This reclaims the full Z range of 252...253 mm. Note that the curtain fan wiring may need to be…
Replace your broken spitvalve (waterkey) on the Allora Aere plastic trombone. Print Settings Printer: Sovol SV01 Rafts: No Supports: No Resolution: 0.1 mm Infill: 100% Filament: CC3D PETG Red Notes: Installation instructions: Install the…
Push a countersunk M2.5 screw through, thread it into your M2.5 whatever and mount a circuit board or fan on top of it using the more common M3 screws. Print it in 0.1 mm layer height with tree supports and well tuned flow factor for the…
A redesign inspired from Sovol SV07 BL Touch Mount by RoyMcNelly on Printables. Redesigned to move the mount and probe out of the way of the tensioner flap to allow extruder gear troubleshooting and cleaning. Designed to print easily and…
An adapter for thing:6308788 SV07 Camera Mount allowing cameras/webcams that are fit with a 1/4x20 thread to be mounted onto the Y belt tensioner of the Sovol SV07. All parts are printable without supports, and no additional metal parts…
Suitable for attaching a CR-Touch auto bed leveling probe using the two bottom screws of the extruder assembly. Use PETG for flexibility and resilience. Support is built-in, no additional supports are needed. Tinkercad design available…
Use the color change at height option in klipper, prusa slicer, orca slicer, or cura slicer (with plugin). Category: Outdoor & Garden
Slides onto 35 mm-diameter rocket body. Two designs: Tinkercad: Straight fins Elliptical fins It's so simple to print even I could do it, please post makes! :) Print Settings Rafts: No Supports: Yes Resolution: 0.3 Infill: N/A Filament:…
Complete part cooling and heatbreak cooling solution for a BMG/Left upgrade of SV01 or SV03 (Sovol). Total weight of the printed parts is 30 grams or less. All fans are 4020: two blowers and one axial. These are an adaptation for the BMG…
Carry anything attached to your key chain from emergency medication to Loop ear plugs. Three tolerances provided for the outer case and you need to properly calibrate your flow factor for these to fit. The tray part should slide easily in…
mike stand for 32 mm dia mike may print fine without supports It's so simple to print even I could do it, please post makes! :) Print Settings Printer: Sovol SV01 Rafts: No Resolution: 0.2 Infill: 15% Filament: Gizmo Dorks PLA Red Notes:…
Use this to support growing plants. Can stack them on top of each other. Three designs are provided. The sturdy design works as base for tomato and pepper plants. Use the thinner one as the top module as the plant grows. The lightweight…
It's a snap-on fan mount similar to the stock E3DV6 mount for 3010 axial fans. Redesigned from basic shapes to fit a 4010 or 4020 fan. It comes with a mounting brace sized for Sovol SV01 or SV03 when mounted sideways as shown in the…
Anchor to the wall behind door to keep it open. When there's stuff that's pushing the door back closed or the doorframe is leaning inward doors tend to become very annoying especially when you have to shuffle through it a lot. Use this…
A nice backplate that helps hold together a Sabrent USB/SATA adapter and a laptop (2.5") hard drive so it can be used as a portable/backup USB drive. Category: Computer
A remix of Fit-over sunglasses temple replacement by broodrooster . Edited in tinkercad to fit my SolarShield 2RH100SE (UPC# 87557700482 I believe) fit-over sunglasses because both original temples have snapped. This is just the left…
Simple design Raspberry PI camera mount for the 20 MM extrusion rail of most budget 3D printers. Each part prints in ~1 hour or less. Depending on the desired configuration, needs: 4 to 6 M3x8 screws, one M3x20 screw, 2 M3 T-nuts, 3 to 5…
To easily remove hotend clogs from above in your direct drive printer get yourself steel rods like these and print the handle and dock above. Put the rod through the handle hole after dipping it in superglue. Sharpening the tip at a 45º…
Requires 4 x M2x8 countersunk screws. Print in the orientation shown at 0.1 mm layer height. Category: Electronics
print with fan mounting plate down. supports may be needed to support the vertical arch. see photo for reference. tinkercad design: https://www.tinkercad.com/things/9Rrb6rPTHPo
There was a need so came up with a design. Works great so far. Source design on Tinkercad . Print Settings Supports: Yes Resolution: 0.3 mm Infill: 15% Filament: any PLA Max/Plus; PETG; ABS any Notes: Use supports for the sink hook piece…
The design features an inner slotted lid and an outer moisture preserving lid and is fully parameterized in FreeCAD through spreadsheet parameters as shown in the pics. Recommended print orientations and support layouts are also shown.…
Completely built from scratch after some frustration with an existing design that required printing with supports which ended up affecting its usability. So this lid prints in 2 parts without any supports. Print in the orientation shown…
use color change at layer feature remix of the logo from https://www.printables.com/model/229585-apple-coaster
A better power supply so Klipper would stop complaining about throttling. Print both parts with the flat face down and enable supports on buildplate only so the two screw holes can print without issue. Any filament material should work.…
Good fix for my fave scissors. M5 nut needed. 1-2-24 Long overdue update: added customizer parameters to the Open SCAD script and generated an STL for M3 based screw, nut, and washer(s). This makes the retainer stronger and can thus be…
Single 5015 blower part cooling + 40x0 heatbreak cooling solution for SV01/03 upgraded with a BMG/Left extruder. ABS only needed for heatbreak duct/holder. Part cooling duct and brace can be printed in PLA. Support for part cooling duct…
Keeps dirty hands/fingers from touching the flask lip that ends up being put in our mouths. Also keeps my cats' noses away from it :) Category: Sport & Outdoors
Has room for Sabrent USB-SATA adapter for 2.5 inch disk drives (HDD or SSD) https://www.amazon.com/gp/product/B011M8YACM/ Uploaded here is Revision 1 with rotated hexagon holes so that the overhang angles are 30 degrees. Will print…
Do away with those part cooling ducts/shrouds. Just install a 4010 fan on this swivel and aim it at the tip of the nozzle. These Wathai fans are very quiet, and they come with the required 2.5 mm bolts and nuts. All you will need in…
Utilizes the spiral_extrude OpenSCAD library, get it form here if you want to change design parameters. May want to use a raft to guarantee adhesion. Bedslingers beware. Category: 3D Printing Tests
SV01 Volcano! (with BMG/Left extruder) Full solution for cooling and level probe mount/shroud: 40x0-axial fan, 5015-radial fan, BL/3D/CRTouch probe. Probe offsets: x_offset: -29.8 y_offset: 17 Suggested parts ( non -affiliated links):…
Add a second 4020 turbine based part cooling fan with this left hand side fan duct and mount. Works with this fan (Amazon link). Supports are built-in, no need for additional supports. Updates: 5/14/22: Rev.5 is sturdier and has an…
This is a replacement for the Rainbird PA-8S adapters for shrub spray nozzles. The top male thread is a proprietary, 5/8 in, 28 TPI (Threads Per Inch) unified fine style thread. The 1/2 in female NPT thread has some steep overhangs so a…
just a napkin holder. should print faster than the voronoi holders out there. no supports needed if you print in PLA and not too fast. Category: Other
Attach a mini LED lamp to the extruder carriage. Tinkercad design . A mount for a breadboard is included. The breadboard allows power distribution from the fan wires to other attachments including the LED lamp. A suggested schematic for…
Remixed with a thicker zstop mount limiter to accommodate the taller Volcano style hotend. Use the 9mm design with the glass bed and the 5.88 mm design with a 1/32" thick FR10/G4 build plate. Category: 3D Printer Parts
Simple, no-frills, fixed dimension, and fast printing, your EZ TUSH baseplate. Works with the wonderful TUSH: The Ultimate Spool Holder by u:filamentry . Source design for FreeCAD included. (fully parametric) Category: 3D Printer…
Print the tops base given here. Then print Irv Shapiro 's bed adhesion test at 50% scale. ( 4592719 -- you will need good squish settings and good cooling to get it right!). This will be the tops handle/axle. Mate the handle to the base.…
Color change at layer Z=2.2mm. Approx size without stem is 2 inches. May want to consider ironing for the top surfaces.
If your cat got smart and figured out how to open the deli drawer on your GE CAFE refrigerator, I know exactly why you're here! Print it in PETG or ABS so it's less brittle. PLA+ or PLA Max should also work. Category: Kitchen & Dining
This swivel mount positions the filament runout sensor higher above the top gantry to facilitate printing very tall models. The v slot mount is snap-in. Requires 3 up to 5 M3 nuts for attaching the sensor to its swivel mount, and the…
This clamp will hold the CZUR Aura antiglare add-on lamp so it doesn't slide down whenever you touch the scanner. I see that they currently offer it only with the X Pro model which has a battery, but Kickstarter packages had this lamp…
