Counting matching models…
My bike trailer has these *** Dunlop valves that are the worst. This adapter stays fixed to the valve(s) and makes pumping air into the tyres much easier. Printed in PETG, 0.4 mm nozzle, 0.2 mm layer height, only perimeters, arachne
I needed to spread an evenly thin and wide layer of SikaFlex glue in a recent project. So I made myself a modular system for a variety of parametric nozzles. When you first open the project file in FreeCAD it looks a bit messy… So let's…
DJI's mini 3 pro drone has no internal fan. When powered up but not flying, the drone tends to overheat and shut down after some minutes. This can be very annoying, especially during firmware upgrades. This model is a drone display stand…
After driving through fresh snow I found the car full of snow… there was a huge gap between chassis and body shell. This model closes these gaps. Printing PLA+, snug support, see 3mf file attached, Any other material may work, too.…
Protect your XLR jacks from getting filthy. Printed in PLA, 0.4 mm nozzle, 0.2 mm layer height, no supports.
A spoon in L and one in S to measure your coffee. L is intended for coffee beans. Printed in PETG, 0.2 mm layer height with some snug support for the handle – preventing supports residue inside the spoons.
coaster in the shape of a sleeping dachshund print in PETG with color change
Flat nozzle (only 11 mm high) to vacuum under spots you can't reach normally. Fits on any standard 35 mm hose. There are two versions of this nozzle: the simple one is in one part. The second version has multiple parts that can be stuck…
I like @Eleton's minimalistic approach, but the loops for the goggle's strap were too tight. So I made them 3 mm longer. Printing TPU, 100 % infill, see 3mf file attached for details.
Cover the cinch jacks on your devices to protect them from filth. FreeCAD file included if you need to adapt the distance of the jacks in the double cover. Printed in PLA, 0.4 mm nozzle, 0.2 mm layer height, 4 perimeters, no supports.
I inherited a Workmate with all four leg springs broken. Looking to replace them I found the model by @noncorporealb_428881 which is precise in dimensions. I took it as a template to make a more printer friendly version that needs less…
I usually leave one battery in the drone, so I need a case for the remaining two batteries. This is smaller than the triple battery charger, so I do not need an extra guard for the control sticks. The upper part is glow–in–the dark,…
I needed to get some grease into the differentials of my RC model car, so I remixed @Alexey's original design into a nozzle with a single opening of 3 mm diameter. See also the original model including a cap . Printing PETG, 0.4 mm…
An organizer to keep my desk tidy. For other purposes you can easily change the outer dimensions in FreeCAD whilst the compartment layout stays relative the same and the thickness of the tray does not change. Photo above shows mine with…
These fenders were designed to be printed in ABS-like resin. Pre-supported files included. Find also threaded versions and a 3mf file with suggested print settings (from the prototypes, PETG) attached to be used on FDM printers. Assembly…
My workmate is very practical, but sometimes I just need a larger flat area to work on in my garage. So I took a rest of a wooden board, and attached two of these mounts so I can fix it firmly on top of the workbench. Only additional…
One open version: if you have more than 2 cables and want to seal it w/ epoxy or other glue. Second version is closed w/ 2 cable through-holes in several dimensions. Change Sketch004/DIAMETER_CABLE constraint for different dimensions.…
Alternative Cover with improved ventilation for your MinisForum DeskMini UM350 mini PC. Use “Cut_Lueftung” as a modifier object in your slicer to remove top and bottom layers so that the infill comes out. Use different infill settings for…
Adapter for trailers with that old–fashioned high towing bar and bikes (e. g. recumbents) that don't have a conventional seat post. — I designed this to fit on the rear rack of my HP Grasshopper recumbent bike. You can alter some…
I don't want that extra tire on the car but just leaving the original rack empty even looks worse. Printing Resin print with “tough” resin preferred. The model already has hollow tubes for saving weight while still being pretty tough.…
In an upcoming project I need to spread glue evenly with a rather small notched spatula. I don't know where to buy such, but I know some FreeCAD. 😁 In the dim spreadsheet you can alter the values to create a spatula with individual…
protect the camera from rain when powered via USB When the camera is powered via USB / an external source, the USB jack is quite exposed. This cover keeps away at least some rain drops… UPDATE: new files w/ slightly altered dimensions for…
The mudguards are designed to fit with the original tires. If you need to change something, Fusion001 is your starting point… Printing The models are designed to be printed in (ABS–like) resin, find manually supported files attached. On…
a handle for better grip on your XT60 plugs / jacks; some glue needed print in PETG, lots of perimeters for 100 % infill, no supports Update longer version added; FreeCAD project file upgraded to FreeCAD 1.1
I needed to measure an angle but had no such tool at hand… Indexing multiples of 5, 10, 15, 45 ° and tapered markers makes it easy to read. Printing PLA, 0.4 mm nozzle, 0.2 mm layer height, external perimeters first, color change
Losi Lasernut U4 – #FPV banger! great FPV perspective: good camera protection: flexible & robust antenna mount: The idea I wanted the FPV camera as high as possible on the car for better view. I also wanted the whole build to look as…
If you have a velomobile with a 19 mm rear axle (like alpha 7 / 9, M9, DF, Milan, Bülk) you know how hard it can be to mount the rear axle because the spacer inside the hub gets misaligned. This tool helps guiding the rear axle through…
One of the brackets of our new sunblinds broke during installation. So I needed to replace it… Fits on a 25 mm tube and for those not-too-expensive sunblinds you can buy under various names online. Designed for printing. Dimensions can be…
Now everybody can make their own THE RESIDENTS Eyeball lamp! All you need besides the printed parts is a 10" (254 mm) spherical lamp and some glue. If you have a lamp of different diameter, scaling the model should also work fine.…
A cap for CLIK valves in any color you want. Print in TPU at 0.2 mm layer height with good cooling!
I've got a small pressure cylinder that can be filled via a standard Schrader valve with compressed air. Max. pressure is about 10 bar – but my pump head tends to slip off before that pressure is reached. This simple adapter adds a round…
These alarms for bikes etc. are quite popular among velomobile riders. Inside one's pocket the buttons of the remote are prone to be pushed unintentionally. So I've created a cover to prevent this. (Yes, the master sketch is not really…
When mounting the rear wheel with a 19 mm rear axle, holding the axle–screw in place can be a real PITA in the limited space within the wheel well. This tool helps holding that screw, so it can not slip out of your fingers. Measurements…
Dachshund Puzzle with simple geometric tiles that give it a origami look. Print the tiles with ironing for a better appearence. All parts designed with minimal tolerances to fit nicely in the frame, you may need to sand some edges with a…
Mounting the rear wheel in velomobiles (alpha 7 / 9, DF, Milan and such) can bee a PITA because the ratchets must be pushed into position… This little tool holds them in place instead. Attach a string (or a wire / spoke) to pull it out…
Cover for a lock cylinder sticking out. You can easily adapt the height in FreeCAD by altering just one value. The cover is a tight fit, no glue needed. Printed in silver PLA, 0.4 mm nozzle, 0.15 layer height & ironing for a smooth…
I like to use otherwise unused LiPo batteries w/ the MT12 radio. Unfortunately the original joystick module won't fit, so… I made this version. Printing The design is not optimized for FDM printers because I wanted to print it in resin…
A Sclaverand / Presta (SV) valve will also fit. PETG, 0.15 mm layer height, lots of perimeters (100 % fill)
The idea is self explanatory, I guess. For those of you daring enough to make changes to the design: good luck! I did not make the FreeCAD project very user friendly to edit. With the sk_Master sketch, the basic shape of the velomobile…
I like the DJI bayonet mount but not the standard action camera adapters with the bolted hinge. Besides poor availability they tend to break too easily. I made a bayonet fastener that acts as a base to build individual and perfect fitting…
Klebesockel mit integrierter Führung für den Kabelbinder. Bowdenzughüllen können fest montiert werden oder mit etwas Spiel ( Toleranz > 0), so dass sie sich im Sockel längs bewegen können um z. B. die Bewegung des Lenkers aufzunehmen.…
Cover the buttons of the Sommer mini garage remote to not unintentionally open your garage. Printed in PLA, 0.4 mm nozzle, 0.3 mm layer height, 3 perimeters. Scale the model if necessary so the cover can glide but still has enough…
I took the simplified design of my chain guard for velomobiles and tailored it to save some weight. The resulting design is not so “user friendly” like the original FreeCAD project anymore, so I decided to share print ready files only.…
Filming velomobile rides with the Insta360 One X2 resulted in two broken mounts. The camera sits on top of the hood and vibrations from riding put a lot of stress to the mount. Removing the battery weight from the camera reduces the…
Heat up the end of the chain tube with a heat gun. Then press the tube onto the tool to form the funnel like shape and wait until it cools down. The widened shape reduces chain friction and wear of the tube. Printed in PETG, 0.2 mm layer…
Print in (tough / ABS-like) resin or on FDM printers, as you like. Pre-supported model and also 3mf with suggested print settings included.
Replacement for broken original joints that hold the back board of our wardrobe. Printed on it's side for strength in PETG, 0.4 mm nozzle, 0.25 mm layer height, 4 perimeters, 30 % cubic infill, organic support.
KettenAbwurfSchutz für Velomobil mit 1× Kettenblatt Ist ein Kettenschutzring vorhanden: KettenAbwurfSchutz einfach Ist kein Kettenschutzring am Kettenblatt: KettenAbwurfSchutz mit Lasche Kein Kettenschutzring und sehr steiler…
To make my alpha 7 velomobile even more efficient I decided to remove the chain tube from the driving side. The chain is now covered with this tunnel to prevent small parts getting into the chain. You can easily adapt it to fit your…
Damit lassen sich auch Pumpenschläuche mit geringerem Außendurchmesser als 10 mm sicher montieren. Die Abmessungen können im dim Spreadsheet in FreeCAD geändert werden.
In the W9 velomobile there is just enough space to keep the water bottle between tank steering and outer wall when the bottle is angled backwards. Therefore a ring shaped bottle holder should be the best. Take some double sided tape to…
A simple handle to turn the closed caps, that seal Sika /glue cartridges for long time storage in a fridge / freezer. Print in PETG, 3 or more layers, enough infill; set scale of both X and Y (but not Z) to 105 %, see 3mf file attached.
A lid for the 0.5 l measuring glass I use as a teapot. Handle and lid are threaded for easy assembly. Printed in PETG for better heat resistance, 0.4 mm nozzle, 0.2 mm layer height, no supports. Scale handle ("Griff") to 98 % on X and Y…
Put load on the front suspension (sit in) and look how much space is between the elastomers and the white POM disc at the top. Then add washers in the right thickness to pre–load the front suspension and reduce shaking of the velomobile…
The original mount for the speed sensor of my Sigma BC 14.16 STS CAD speedometer has a very small joint. While being mounted on the front suspension strut of my velomobile, it broke… The replacement sensor is now glued onto my new holder.…
To cover the front axle / bearings and improve aerodynamics of the velomobile. Designed for 15 mm axles with 11 mm inner diameter. Printed in PETG, 0.3 mm, no support. Update: added tubes in two sizes (0.3 and 0.45 mm thick) you may glue…
I nearly lost my One X2 two times because of breaking mounts. First time a plastic frame broke, next time (see video) the DJI bayonet adapter. First step to the solution was to reduce weight by removing the battery from the camera, see:…
The new motor for my U4 is a bit larger than the stock one. So motor mount and center differential need to be 2 mm higher. Printed to test height needed and as a (drilling & cutting) jig for the final aluminium version.
I have an extra power circuit for the FPV gear parallel to the car's drive and wanted to have the Deans T–connector mounted in a tidy manner. Tap M3 threads into the main part before assembly. Use CA to glue the jack in. This was designed…
Die Verlängerung des Mastes ( Verlaengerung_gesamt ) und die Überhöhung des Luftauslasses ( Auslass_hoeher ) sowie ein paar andere Parameter, inklusive der Breite (=Höhe) des Auslegermastes können im Spreadsheet dim individuell angepasst…
10 (ten) new LACK tables in the house and I know how cumbersome it is to screw in the legs. That pain 40 times? 😣 There must be a better solution, … so here it is: LLTT — the ultimate LACK Leg Turning Tool Printing PETG, 0.4 mm nozzle,…
Handle to open / shut the velomobile race hood visor. Needs a 4 mm bolt for mounting. Mounting position may vary for individual needs. Printed in transparent PETG, 0.15 mm, no support.
Select the cover depending on how many channels you are using (i.e. channel 1 to the highest number used). If it does not fit, change channels_used in the dim spreadsheet and/or the sketch005 in FreeCAD. Update I added a holding fixture…
now for SLA printing, manually supported model
console for the mount of a Sigma BC 14.0 speedometer you may change the angle within Sketch001
Alter count according to the number of elastomers you want to replace; you may also add some additional height. Print in PETG, see 3mf .
Mit doppelseitigem Klebeband am Boden der Karosserie befestigen. Druck PETG, siehe 3mf Datei
Protect your shoulders from the sharp edge of the manhole.
HeckAdapter ist die Basis, auf der verschiedene Halterungen aufgebaut werden können. Das Modell ist für die Langlöcher hinten in meinem Alpha W9 konstruiert. In der Tabelle dim können die Werte für das Langloch (Breite und Höhe) sowie die…
Befestigung per Kabelbinder. Druck TPU (GF), kein Support, siehe .3mf Datei Anpassung Rohrdurchmesser Das Modell wurde für den Tiller des HP GrassHoppers mit 30 mm Rohr konzipiert. Der Durchmesser kann direkt im ersten Sketch angepasst…
Im VarSet kann über die Variable toTop bestimmt werden, wie weit die Unterkannte der Öffnung von der Oberkante des Modells entfernt ist – also wie tief der Bremsgriff unter der Karosserie gehalten wird. Voreingestellt ist der Wert, den…
Original model by ChristianW: https://www.velomobilforum.de/forum/index.php?threads/der-vm-hupe-faden-hupen-horn.79369/#post-1872467
Druck Gehäuseteile aus hinreichend stabilem Material, LenkStockManschette und KnickSchutz aus Flex. Kein Support nötig. Details siehe .3mf Dateien. Zusätzliches Material Kippschalter mit Kappe ein/aus/ein, z. B.…
Designed for N45 magnets Ø 12 mm × 6 mm (rated 4.1 kg) and printing at 0.2 mm layer height. You can easily alter some dimensions in the VarSet. watchStrapOffset adds extra space between the holder's magnet pad and the part you wrap the…
Intended for the TPU camera holder (incl. bolt & nut), that comes witch the Thumb2. Use Ø 12 mm × 6 mm N45 magnets for the outer part (ActionCamMount) and Ø 12 mm × 8 mm for the counterpart. Print in TPU to protect the velomobile's paint,…
Make distinguishing bottles (their contents) simple – color code your drinks. Made with FreeCAD.
You may re-pack the battery pack that came with your velomobile, or use alikes (e. g. Ansmann 4S2P Akkupack 8x 18650 Kabel Li-Ion 14.4 V 5200 mAh) Additional parts 14 AWG wires, red and black 0,5 mm wires, red and black (display ->…
Mein GrassHopper fx hat einen Tillerlenker. Die Öffnung für den nicht genutzten Untenlenker–Steuersatz hatte der Hersteller seinerzeit "kreativ" verdeckelt. Schlussendlich fiel das Dingens irgendwann ab – also schnell einen passenden…
These are all currently available results.
![DJI Goggles 2 Battery Strap Mount remix [TPU]](https://media.printables.com/media/prints/656002/images/5171017_25828a99-ebd7-4986-9e0b-fb6dfbe59805_3410f5e7-0e2a-45c6-bafd-a80f3e969207/dji_goggles2_batteryholder_20231122_192011401_hdr.jpg)
![CLIK Valve (SCV) to Schrader (AV) Adapter – also works with SV! [FreeCAD]](https://media.printables.com/media/prints/52d2f52e-1a03-4369-a833-59a7ae6358ad/images/9255501_944951f9-9001-4ee2-a9b6-4083009518b0_d82ae132-f0c3-4a6e-881c-81f238ff9290/scv-schrader_20250318_194200750.jpg)
![Klebesockel für Bowdenzughüllen im Velomobil [FreeCAD]](https://media.printables.com/media/prints/90738555-3363-4881-a81e-f8bf93bc9aec/images/9319636_7a95b006-21d7-4bba-ac2a-c08ed1720f0b_4a349bc2-fb23-4b3b-90b0-3be8855ebe0c/kbs_20250325_1953263752.jpg)
![KettenAbwurfSchutz für Velomobil mit 1× Kettenblatt [FreeCAD]](https://media.printables.com/media/prints/5afc384f-8f8e-4d57-a02d-36c1a65c9eb2/images/9286424_8f3881b3-6e61-4c44-a08a-17a4846712bf_8252b084-bf55-4733-87db-c1ecdd21e3ab/image-20250322-172149-502.jpeg)
![Verlängerung Ausleger Mast als Umleitung der Zuluft im Velomobil [FreeCAD]](https://media.printables.com/media/prints/032fc7b0-0e4c-4a90-838b-2936d364f762/images/9391482_5e73895e-7043-443e-a414-5980234c71a6_ba4e587a-dd42-4c4a-a685-b6e714b89aea/20250401_153655857.jpg)
![Flaschenhalter liegend fürs Velomobil [FreeCAD]](https://media.printables.com/media/prints/23081f1b-5143-4c12-81b7-f0daa6bcd8ee/images/9340153_87faf219-1224-4465-95e9-3e7f1046de86_5dc99572-dc3d-46df-8a31-93d6abe8dcc8/flaschenhalter20250327_172256527.jpg)
