Counting matching models…
Please Note: This Design is not being developed or maintained, and is now obsolete, please go for either the REDUX or the PRO DIY Steam Machine: REDUX DIY Steam Machine: PRO If anyone would like to support me and my work, please feel free…
Update: 27/10/2026 I have uploaded the version 4.2.3 face plates and the button bodies with the leaf spring system, I recommend printing the button body from a 60 to 70D TPU, if you have multi material system you can print the main part…
Update: 4/07/2026 Alert! PRO Version 2 Incoming: For anyone looking to build the PRO, please wait, I have Version 2 in coming, its fully complete, and much better than the first version, the case is now unified and supports…
Just a simple remix of the lid riser, I dont print PLA or PETG so I prefer a solid riser as I want to reduce heat leakage as much as possible, I also reduced the gap at the rear and put the K1C logo on the left. Print with supports for…
Update: 04/07/2026 Version 2 incoming, please hold off on printing this, the new one is better, I will be uploaded soon, I'm just short on time, but Ill try and get it up before the end of the weekend. Update: 27-03-2026 Ive added a…
If anyone would like to support me and my work, please feel free to donate/tip me on Ko-Fi: https://ko-fi.com/nexgen3d Update: Added Step file for the project. Introducing the NXG3D LeGo CyberDeck: Personally, I think Lenovo should have…
Simple stylish protective case for the Legion Go with integrated audio redirectors. Recommend printing from PETG or PETG-CF, I did mine in PC-CF, avoid stiff plastic like ABS and ASA. Supports are needed at the bottom for the USB-C access…
18/09/2025: I have some of these complete and ready to go on eBay if anyone is interested: eBay Listing Update 18/08/2025: Made some slight changes to the front case, giving the battery pack a little more room, approximately 1.5mm of…
///////////////////////////////////////////////////////////////// Update: 2/10/2026 Uploaded files for the Thermalright 6.86" LCD Display Link to the product: https://link.amazon/B0j0CNDgn Link to the software setup for Bazzite:…
If anyone would like to support me and my work, please feel free to donate/tip me on Ko-Fi: https://ko-fi.com/nexgen3d The Creality K1C is not a bad printer, and so far has been a pretty reliable work horse for the money, but…
Im proud to release the version 1 of my universal chamber heater, the control system and power setup will be up to you, I will add these details later on the next version. BOM: 1 x 24v 7530 Dual Ball Bearing GDStime Blower Fan…
If anyone would like to support me and my work, please feel free to donate/tip me on Ko-Fi: https://ko-fi.com/nexgen3d 24/10/2025 I have had a few requests for a tray to suit a Raspberry Pi, the below image is what I have been working on,…
I created this so I could mount some Dell Optiplex 7040 USFF (Micro) PC's under a desk, may suit other Dell, HP and Lenovo machines. I printed from PETG-CF and is plenty durable, I'd recommend using PLA+ or better. I desined this to pint…
I made this specific for the BC250 Micro-Fit connectors, as there was no way to lock them into place, and this also stops you from mixing them up, so you can connect all 6 pins on each without worry about crossing them over. I made this…
///////////////////////////////////////////////////////////////// Update: 11/8/2026: I have created an assembly guide for this mount here: https://github.com/NexGen-3D-Printing/SteamMachine/discussions/72 If you have any questions, you…
Update 11/10/2024: I will be uploading an updated version of this model this weekend (After I fully test everything), I have a new rear battery cover with a built in power switch, as the soft off for the V3 still chews power, and I have…
After looking for a simple bolt latch, I didnt see anything that I liked, so I designed my own, please print in the layout I have displayed in the attached image to maximise the strength. I've also attached a Fusion 360 Step file so you…
New version of this here: https://www.printables.com/model/1017019-nexgen3d-meshtastic-atak-heltec-t114-case-v2 Note: I have ordered in some Beofeng clips, so when they arrive I will redesign the back cover to support them, so if your…
Simple two part underdesk drawer, I printed another draw that looks like this one, found it quite weak and the draw would just fall out with when the slightest bit of weight was applied, so I tried to fix it, but it was just easier to…
Simple AIO hose management clip, I designed this to suit the Artic Freezer III but should be fine with others. I designed it to suit 13mm hosing as the Freezer has wires and nylon braiding over the 10mm hose, so I need them to have loose…
Simple drag chain thats optimised for printing, the links have an “A” and a “B”. The B and A are opposed to each other as in the images, very simple desing, no silly retaing parts, the links do the retaining instead. For clamping, you…
27/09/2025: Had some clearance issues with the DXC extruder, so I made some slight tweaks and reuploaded the riser, the previous one is fine if you run the stock extruder. 26/09/2025: New and improved version of my K1/K1C Lid riser, I…
Just a simple buck converter case, has cable tie points, max size is 6mm x 2mm, requires 4 x M3x6mm SHS or BHS. Buck converter is the LM2596S. Thank you to LxL3D for the use of the LM2596S Dummy model, which I used to make this case,…
Update 2025: I just uploaded a Version 2 of these and the Step file if anyone wants to make changes to them. Update: Just added some alternative feet for those that would like to angle the speakers back, also added 2 mock-up 3D files so…
Revised version of my 3D Printer Chamber Heater: With my ongoing work on my NXG-3D3 printer, I wanted to add my chamber heater system, so I thought I would clean it up and make some changes to the original . This one does not require any…
New version here → QIDI-TECH X-Max/X-Plus Ratchet Dials - V2 I think these should be the default on any printer, as the lock nut system is annoying, and the printers that have no lock nut, well lets say, is frustrating to have to keep…
After buying K2 Pro and finding out that there is a ridiculous amount of stress placed on the stock couple being applied by the filament buffer and the CFS, I decided to fix the problem properly. I found someone had already started this…
Bicycle chain tensioner and guide, helps to reduce chain bouncing on mountain bikes when hitting rough terrain. Upper part needs to be printed from TPUI, lower half and pulley should be printed from PETG-CF or ABS, in my case I used…
Please Note: This needs a printer with a 300mm x 220mm build area minimum, I designed it to take advatage of the K1 Max printer. Simple wall mounting system for the Surface Pro Tablet. I have tested this with the following tablets:…
Needed a good universal motherboard tray to suit the Makerbase MKS-SKIPR board along with their new UTC CANBUS board. Print from anything you like, but I would avoid PLA unless the environment is cool, otherwise, ABS at a minimum, You can…
Simple fan duct for assisted VRM cooling designed with the HYTE theme, designed for the Y70 case but should fit many others, bolt pattern matches a 140mm fan, and is designed to fit over a 120mm fan. Requires 4 x brass threaded heat…
Just a simple bracket for mounting the common Bose TV Speaker to the wall, the bracket has a 5 degrees angle to direct the soundbar slightly downwards. The model this is designed for: Bose TV Speaker Print on its side for maximum…
Please Note: Fan should be installed to pull air through the filter and exhaust out towards the back, this gives you the max performance of both the fan and the filter, and will stop crap from building up on the fans. Update: I have…
Simple trim to cover/hide your fans and radiator in for the Hyte Y70 PC case, can be used in other cases, but I specifically designed it to fit Hytes theme. There is two types: Type 1: This is for a push pull system with fan + rad + fan…
I’m proud to finally release my NXG-Node to the 3D Printing Community. I originally intended to make these and sell them, but due to other forces in my life, I have decided to just release the files and let others make and enjoy this…
I desinged these some time ago to replace the original ratchet dials for the older X-Max and X-Plus printers but never got around to uploading them, these are imporved over my ealier design, the fit more snuggly and install easier, they…
New version of this here: https://www.printables.com/model/1017019-nexgen3d-meshtastic-atak-heltec-t114-case-v2 I made this magnetic dock to suit this case:…
This is my new CleanAir system, I've made several improvements over the previous version: Thicker lid and rail system Magnetic pogo pin system Multi stage filer system Cleaner style Various model fixes With this new design you can rapidly…
NexGen Clean Air Desktop Edition I created this to help keep my office air toxin free as I run several printers in there with me and I think there would be a few others that also do this. I already run my Clean Air filters inside the…
Very simple chain stay protector, its heavy duty and should last a long time under the most extreme conditions. Just use zip ties to hold in place, I have provided 2 models, 1 is 250mm long and the other is 300mm, you can stretch and…
Just a simple solid keystone wallplate for RJ45 sockets, the one I use with this → CAT6 Shielded Keystone Dimensions: Print from whatever you like, I print mine from Matt White PETG, just print face down, no supports needed for anything.
5" Sensor Display Mount designed using the HYTE theme for the Y70 case, but can be used in others. This mounts to the bottom of the upper 120mm cooling fans. You will need the following: 4 x M3 Heat Inserts 4 x M3x6 or M3x8 Bolts 2 x…
7/10/2025 Its cleaning up nicely, wont be long and I will start testing the motion system: 5/10/2025: Slowly coming along, hoping to start the wiring this week so I can at least start testing the motion system: 3/10/2025: Had a chance to…
The following video is the early prototype: This was a project of mine from a few years back, its pretty much a done deal, I dont own these printers anymore but when I did, this was the tool head I used. If I can find the Step files I…
This one is a little more refined over my Surface Pro mount as I own and use these Tablets, and have several mounted around my house. I have tested this with the following tablets: Dell Latitude 7200 2 in 1 Dell Latitude 7210 2 in 1 I…
I made this mount so I could mount some Behringer Amplifiers under my studio desks. Have tested with the following Amplifiers: iNuke NU6000DSP (Recommend 2 Pairs) NX1000D (Requires 3) NX3000D (Requires 3) Should be printed in PLA+ as a…
Just a simple cable comb clip to suit the Asrock Steel Legend X670 board, this is just to manage the USB 3.0 and USB-C Type-E header connectors, probably very specific to this mother board, but you can try it on others if you think it…
This is an adaptor to allow you to mount a Raspberry Pi 3 A+ into one of the Sata drive cages in the HYTE Y70 case to run my LCD Sensor Panel mod found here . This should fit other cases, but I specifically made it to suit the Y70, the…
Simple display stand for the LTT Scribedriver Bolt Action Pen Assemble with a tiny bit of super glue.
I picked up a Fractal-Design Mood case despite the review from Steve at Gamers Nexus, but after assembling the machine, I noticed, no matter what speed the fans were running at, cover on = 10x louder, remove the lid and fans are almost…
I wanted an easy way to extend the range of my bike, and to leverage the batteries I already own, so I created the BoostPack. Features: Can use the following Dewalt batteries: 5ah 18v Standard 5ah 18v PowerStack 8ah 18v Standard 8ah 18v…
I purchased this very much useless 2-in-1 Laptop, for a whole $59.95 AUD delivered, and after trying every Linux distro and Windows OS on this thing, I came to the conclusion that this thing would have been hot garbage the day it was…
Just a simple mini junk draw for the Honeycomb tool wall system. The outer pod has a dovetail groove system so they can interlock together, I have included my own designed Honeycomb interlock, just secure it with some M3 x 8 to 10mm BHS…
I needed to install this silly Asrock Arc A770 into my main CAD workstation as I repurposed my RX 7900 into my open source gaming console. The Asrock card is as ugly as hat full backsides, so I thought I would try and improve it to match…
These are all currently available results.
