Counting matching models…
I wanted a bin for the side of my Prusa MK4 to catch the filament that may droop down while the nozzle is heating, then fall off the right side of the printer as it goes through the auto-leveling sequence. These small 1-2" strings of…
Print approx. €5.25–€6.42 excl. taxPreliminary estimate for one variant
This is yet another playing card box. It's a simple model, but quite functional. In addition to providing a nice place to store cards, the base makes a great draw pile holder, and the top makes a great discard pile holder. The…
Print approx. €4.20–€5.13 excl. taxPreliminary estimate for one variant
This is a Shulker Box from Minecraft , albeit only 75mm cubed rather than 1m cubed =) The dimensions are accurate and the pitch of the thread rises the box accurately too: 50% of the height of the box per revolution, just like in…
Print approx. €18.88–€23.07 excl. taxPreliminary estimate for one variant
I wanted a bin for the side of my Prusa i3 MK3*s to catch the filament that may droop down while the nozzle is heating, then fall off the left side of the printer as it goes through the auto-leveling sequence. These small 1-2" strings of…
Print approx. €4.82–€5.89 excl. taxPreliminary estimate for one variant
Inspired and challenged by the legendary Emmet Lalish's very early work in 3D Printing as a new manufacturing technique, I created, entirely from scratch : a folding heart box. I would encourage others to go on the same journey! This box…
Print approx. €1.66–€2.02 excl. taxPreliminary estimate for one variant
I mount my spools on the wall now and wanted a way to also mount the end of my PTFE tubes. Since the direction that the PTFE should draw from the spool changes depending on how full the spool is, I wanted something that would change pitch…
Print approx. €1.79–€2.19 excl. taxPreliminary estimate for PETGSource material: PET
I use Dollar Shave Club razors. In particular, I use their upgraded Executive razors/blades. I finally got tired of them falling out of our soap dishes in the shower, so, I designed this dual razor holder that clips on to the shower pipe…
Print approx. €3.15–€3.85 excl. taxPreliminary estimate for one variant
I started this battery dispenser project with the following design goals: It should enable a FIFO (First-In, First-Out) system It should hold 24 batteries ("value pack" sized) It should have a front-loading slot (at the top) It should be…
Print approx. €6.63–€8.10 excl. taxPreliminary estimate for one variant
I have a Quartet Whiteboard and designed this 6-marker holder that slides over the whiteboard at the top. I printed mine in black PETG. 1-Jan-2024 - Added a version with 1.9mm holes for markers made by other brands such as Expo.
Print approx. €6.15–€7.51 excl. taxPreliminary estimate for PETGSource material: PET
It has been my experience that HEPA/Activated Carbon filters are rather expensive. So, I was delighted to find these P60 filters ( Non-affiliate Amazon US link ) at a resonable cost (~$5 each). I've been using them in my house in the…
Print approx. €4.22–€5.16 excl. taxPreliminary estimate for PETGSource material: PET
Wanted a cover for my C610 that just worked. Designed this in Fusion 360 and it works great! The thin ring front means you can see the LEDs on the camera when they're on whether the cover is opened or closed. This uses a print-in-place…
Print approx. €1.43–€1.75 excl. taxPreliminary estimate for one variant
This one is designed to be printed with tree supports and the results are fantastic on my MK4. I printed mine in Overture Professional PLA (Electric Blue) and it's nearly flawless. The dispensing window works well. There's also a pair or…
Print approx. €3.00–€3.66 excl. taxPreliminary estimate for one variant
I designed this XL D20 for printing on my Prusa XL. I used organic supports, but considering the underside looked perfect and the supports just popped off in one piece, I wonder if they were ever really needed. This is printed in two…
Print approx. €2.36–€2.88 excl. taxPreliminary estimate for one variant
EDIT: 18-MAY-2025: Updated the perimeter pieces to have their tabs. EDIT: 6-OCT-2020: Congratulations to Roger Penrose on his Nobel Prize relating to his work on black holes. I've always been fascinated by Penrose Tiling and I decided to…
Print approx. €0.39–€0.48 excl. taxPreliminary estimate for one variant
I've started making some of the nice HKCams created by another user here https://www.prusaprinters.org/prints/1717-homekit-camera . The website for this project is here: https://hochgatterer.me/hkcam/ . His software is easy to install on…
Print approx. €0.66–€0.80 excl. taxPreliminary estimate for one variant
A kind user from Germany was lamenting that this box wouldn't work for the German standard of 59 x 91mm for cards. Here you go!
Print approx. €4.21–€5.15 excl. taxPreliminary estimate for one variant
My printers are sitting on a paver (slab of concrete), which is itself on top of a bit of foam rubber. This substantially reduces the noise produced by vibrations that resonate in the table beneath the printer, but also lifts the printer…
Print approx. €18.13–€22.15 excl. taxPreliminary estimate for one variant
Not a new idea, but this is my take. I love these little boxes! I keep a dozen or so printed in various colors at all times just in case you need to thank someone. We display them around the house at Christmas as decorations, so there's…
I needed a method of connecting a "webcam" to my printer for remote monitoring from around the house via Octoprint. So, this comes in a couple pieces: A connector that snaps to the 30x30 extrusion frame (Y-axis on Prusa, and possibly…
This is a fairly simple model of a larger-than-life bolt and matching nut. I created this as a piece of shelf art and it's pretty fun to just play with, but there's also a hidden compartment inside the bolt. Could be a great place to hide…
I've seen other Minecraft diamond ore lamps in various places by they all seem to lack the definitive pixelation that Minecraft embraces. By leveraging techniques used from 3D printed lithographs and some of the features of the latest…
These are some Modern-esk hexagonal plant pots. They have the same footprint and the same built-in water tray. There are smallish holes at the bottom of the inside to allow the tray to serve as a reservoir. The mid-sized one was designed…
I small print to give my Apple Watch (44mm) a better home on my nightstand. The design allows for the cord to go to the left or the right. On my print, Apple's magnetic charger fits perfectly in place, which is then snug against the watch…
I wanted to label the various spaces on my Heavy Duty Metal Storage Shelving Rack in my home office. I've designed it to nicely hold Avery 8860 labels (1 in. x 2 5/8 in.) so I can easily 2D print nice clear labels on my ink jet printer,…
This is a tiny little project (about 1 gram of filament), which simply creates a refrigerator magnet out of a 10mm diameter x 3mm neodymium magnet in the shape of a popular type of thumbtack. I bought 35 of these magnets from Amazon (US)…
I wanted to make a Thwomp pencil holder for a gift and while there were existing models available, I wanted to design it myself. I'm really pleased with the results! Print instructions I used Paramount3D Gray for the base, Solutech Merlot…
The original is a great phone case! It fits great and protects well. I made a couple of quality of life improvements: Slightly enlarged the silent switch hole so I can switch the switch. Slightly enlarged the charge port hole so I can…
This is a project I put together as a gift for my niece. I've only made the one and I was super pleased at how well it came out! I used the existing (Totoro)[ https://www.thingiverse.com/thing:12146 ] model by (Joo)[…
There are a lot of other Vice models here, but this one is mine. I like it because it looks cool (to me), is 100% 3D printable (without any supports) and works well for my purposes which is to hold Pi Zeros and their pHats for soldering,…
This was quickly put together to solve the problem of blocking the LCD when I don't want the light it emits. Unlike some of the other designs, this shouldn't leak light around the edges as the plate has 2 tiers, the first that fits nicely…
I needed a simple desk organizer. I looked around, but I didn't find any that looked like it would match the decor of my living room where our family computer desk is. So, I made my own. It's basically just a cup, with a wider tray base…
I decided to try my hand at some coasters. I normally partake in cold drinks, which eventually condenses a lot of water around my glass, then drips everywhere. PLA isn't particularly good at soaking this up, so I know I wanted to depend…
So, I noticed a mouse in my garage and decided to remedy this. I have a 5-gallon bucket from Lowe's hardware store and noticed that it already had a spinning contraption built into its handle. So, I designed a finned bait-holder that can…
I needed more toe-clamps for my CNC table. The ones that came with it are injection molded using some variant of PA15-GF (Nylon with glass fibers). This is a good choice, but I still have some Prusament PC-CF. This is a stronger material…
OK, so this is a remix of my own model here: https://www.prusaprinters.org/prints/5805-tesla-model-3-tray-wj1772-storage-slot . I've integrated a USB Hub into the tray. This essentially adds 3 more USB ports, which is perfect for me to…
We have had this lamp proudly displayed in our home in our foyer for nearly a year now and we get lots of compliments on it! It is super easy to print. This lamp assembles from 12 sides all printed flat on the printer's bed, which then…
I thought I had an original idea, but it seems others faced the same issue I had. Waking in the middle of the night to turn on the fan, only to accidentally flood the bedroom with light. This is my take on it. In my case, my ceiling fans…
There's a lot of phone stands already, but I wanted one that I could adjust the angle of display of my phone so I toyed with the idea of a simple ratchet like mechanism along with a hinge and it turned out really great! This is entirely…
This is a clock based on a super-large bottle cap from a Nuka Cola bottle of Fallout games fame. I started with the model by techoutreach]( https://twitter.com/tech_outreach73 ) here on PrusaPrinters but modified it to: integrat the…
I had a look around and saw that there were some models like this already, but I wanted to make modifications and found that editing the STL files was a nightmare due to their construction in other programs. So, I set out to make my own…
This handy travel soapbox transforms into a nice soap dispenser and back again. The tray is positioned very low in the box when using it as a travel soapbox, but when opened can be positioned higher for presentation of the soap bar for…
The OEM Prusa i3 MK3* spool holder has been fantastic, but, with the welcomed transition to cardboard filament rolls from many manufacturers, can lead to the creation of unwanted dust as the spools that drops directly down onto the print…
This particular STL/3mf file contains geometry to make the handle for my 20 Ozark Tumbler, which is approximate 87mm in diameter. Note that the ring is actually slightly tapered so that in matches the tapering/curvature of the actual…
I have a couple of sealed document boxes that I used for dryboxes for longer-term storage of humidity-sensitive spools of filament. I didn't want the spools touching the silica gel beeds covering the bottom, so, I made this bracket that…
I recently treated myself to a pair of prescription Carerra Ducatis (model CARDUC 006/S ). It took nearly 2 months for my prescription to get made for some reason, so I decided I didn't ever want to lose these. So, I made case for them…
I now have a growing number of printers and have growing concern about particulate microplastics and VoCs from printing with various polymers in my printing space. So, I wanted a reasonably quiet, always-on air filter. I selected some…
A nametag that says "Guy". I made this for a Halloween costume. Using PrusaSlicer's ironing mode made this little print come out looking perfect! I used a filament pen to “glue” a button clip to the back and attached it to the shirt as…
A nice cozy sleeve for your GoPro Hero-series action cam. Plus a version with a wrist-strap loop. Print instructions I need to mount my GoPro Hero 7 to my RC Drone. It is expected to crash from time-to-time, so I wanted a sturdy, "cozy"…
This is a mod of nerdpersonthing's SD Card box, but for USB-A dongles! It holds up to 6 dongles–typically mouse/keyboard or bluetooth dongles–which are easily misplaced! Credit goes to nerdpersonthing , this is mostly cosmetic changes.
I operate a small print farm and, like any business, it is important to maintain stock levels of raw materials. In my case, this is FDM filaments. I keep them all on shelving and I like to be able to see from across the room how many of…
As PrusaLink/PrusaConnect now supports USB Webcams, I've remixed Prusa's Raspberry Pi Zero frame for Einsy Rambo model to provide some protection for Waveshare's Ethernet/USB Hub pHat. The Waveshare pHat comes with brass spacers and some…
I've been itching to do a multi-color TPU print on my Prusa XL, and, since my son needed a phone case for his iPhone SE/8, I thought this would make a nice project to try. The artwork is original (generated by OpenAI's Dall-E and a bunch…
This is my original model and is my Saint Valentine's Day Gift to my lovely wife. It features a heart shape which is hugged by me (upper arm) and our son (lower arm). This is a 2-color print and is sliced for my Prusa i3 MK3S + MMU2S. I…
So, I love the Universal Auto Rewind Spool Holder . And the "spool nut" it comes with fits my rolls of Prusament perfectly. Unfortunately, it doesn't fit my other brand of filament I use often, it's too small, so I created a parametric…
This is an over-engineered solution for a minor problem, but…. I got fed-up with my mish-mash collection of ¼" ratchet sockets and decided to buy a clean set of metric ones and another clean set of SAE ones. When I got home, I noticed…
This is a remix of my previously posted print Privacy Cover for the Logitech C610 Webcam that adds an eye when the cover is open for a constant reminder that one could be being watched. Print instructions Load Galaxy Black in spool #2,…
Simple, elegant, functional! This is a dishwasher status indicator. Rotate it to "DIRTY" once you empty the dishwasher, rotate to "CLEAN" when you set it to wash. No more shouting across the house. "Is the dishwasher clean or dirty?" This…
So, I ordered some filament on 2kg spools, but those don't fit any of my other spool holders and won't fit atop my MK3Ses, so, I needed to re-spool the filament to 2 “normal", 1kg spools. I already use these spool holders for my…
So, I have a few MK3S+s and I'm in the process of replacing their normal brass nozzles with Diamondback Nozzles (I cannot recommend this enough!). These nozzles ship with a nice sticker and I opted to use this as a “badge” on the printers…
These are all currently available results.
