Counting matching models…
A tool to remove the nut from a Radiomaster TX16S switch. No idea how long it will last, but it works and gets the job done. Printed with 2 walls, with an alternating extra, 60 pct infill.
A template/drill-guide for mounting the cabinet side of Blum door hinges. The critical dimensions here are: 32mm between the holes, and 1-7/16 in (36.513 mm) from the front edge of the cabinet to the holes. I made the holes in the…
Cowling for the Tower Hobbies Phoenix Model Sonic Mk2 Low-Wing The cowling should slide right over the nose of the plane. Attach it with 4 screws of your choice. Arguably I could have cut off the part of the fuselage that extends along…
This fits a Holmes box fan that is about 10 years old. Could fit newer too. None of the numerous box fan feet already here at Thingiverse fit quite right, or stayed in place. It's a tight fit and it takes a decent shove to get it into…
A case for the Motorola Moto G Power, 2021 version. Printed in PLA. PETG would probably work fine as well. I've printed this number of times and I'm pretty happy with it. File: MotoGPower2021Case_.stl I added a design for flexible…
Great design but I wanted a few modifications. I thinned the section where the mounting screw goes, so I could use the original screws and still have thread engagement similar to the original hinge. I made a new bottom-side hinge by…
If you decide to make a 2-shelf and a 3-shelf unit from a 5-shelf unit, you need 4 more feet. Or maybe one foot broke, or got lost. That's where this comes in. It's an HDX shelving unit foot. The fit is good. I printed in PLA. It seems fine
Update: I'm happy with the knobs, and they work great for regular grilling (maybe a couple burgers with two burners on for 15-20 minutes). But one day I had all 4 burners going for 45+ minutes, and it seemed like the PLA was getting soft…
I started with rcKeith's spinner (thanks!), then stretched and modified it so it would work with a Windsor 12 x 6 x 3 three-bladed prop. I've flown this and it works well. This is designed to work with the original FW-190 motor…
If you remove your doors and hinges to paint your door and frame (you should...), you can use these to keep the paint out of the mortise area. These are dimensioned exactly to standard mortises so they might be a tight fit. I have one…
Battery tray to hold the CNHL Black Series 3200mAh 14.8V 30C 4S Shorty Lipo. Holds the battery and prevents it from crashing into the flight controller, or the wires going to it.
I bought a Poly 1200 lb capacity dump cart/yard wagon from VEVOR. Great wagon, but when you put (or drop) the pull handle to the ground, part of the metal hitch (for towing) hits unprotected. This scuffs up the metal and removes the…
Slightly reworked for a Tower Hobbies Mk1 P51 Mustang.
I found the original v.03 stand held the jack a bit loose for the Cable Matters 180005 punch-down keystone, so I tweaked it a bit in Tinkercad to get a tight, no-rocking fit. (Thanks rssalerno for the original model. It's always much…
This piece fills in the blank areas to the sides of an aftermarket double-din stereo for a 2002 Toyota Highlander. This should work on any Gen 1, 2001-2007 model with standard audio. (I do not know if it works with the Bose Audio…
A tool for adjusting the height of Peter Meier 415 Plastic Cabinet Leveler. There is tool for the Smile System cabinet levelers, but the 415 Leveler has a different shape. This tool is mostly unnecessary for normal lower cabinets. You can…
The handle broke on my favorite red scissors. I super-glue'd it, but it kept re-breaking. I was looking for a project to practice Fusion 360, so I made new handles. Mine are not as ergonomic as the original, but they fit the blades and…
02-11-2018 Anet changed the default A6 power supply around the beginning of 2018. The STL has been modified to accommodate the change, and still work for pre-2018 printers. (i.e. some internal features were removed, and the screw hole…
Update: April 2023 I flew it. No data to back it up, but the flights seemed noticeably better all round. The prop noise was definitely reduced. Not silent by any means, but less noticeable. It flew smoother in bumpy air, with less…
I bought these little submersible water pumps for a project. Unfortunately the liquid I was pumping (water with an anti-fungal, anti-bacterial additive) caused the acrylic(?) pump cover to crack and fail. I ended up using using a…
Same design as the original, except I modified the threads to work with my watering can. My threads were very flat and shallow. The D (maj) was 23mm, and the D (min) was 22mm. The threads were spaced 6mm apart. The thread profile was a…
Thanks to charetejohn for starting the design. I took that original design and extended the servo retaining mount so I could hold it in place with screws. I also added holes for screwing it down to the wing. Works perfect with Hextronics…
A battery adapter so you can use Ryobi One batteries with Sears Craftsman 19.2v tools. Mar 2023 If you want to tinker with it, I've included the step file for the middle shell. It was modeled in FreeCAD. To make the full part, you merge…
A cowling for the Mk1 Version of the Tower Hobbies P51 Mustang. (Yes, she's a little beat up ;-)
A 3D printable matrix ball guide for the Johnny Mnemonic pinball game. This is a commonly missing part on Johnny Mnemonic pinball games. The original is made of stainless steel. This is a close facsimile I made by looking at photos and…
I snapped off the corner of the front plate of my Anet A6. Fortunately, it still held the rod well enough that I could print, so I designed this replacement. As close as I could measure it, this is dimensionally accurate for the front…
You can use this template to locate the screw holes for your Blum HK Door Bracket. The two stls file have the same hole locations. I just realized the "non-small" one was unnecessarily big, and made a smaller one. (But since the photo is…
A Jig-Template for a Blum 3-Hole Hidden Hinge Clip. Could not find the dimensions on the internet, so I measured and tested to get these. 9.5mm from edge to the first holes. First holes are 40mm apart. Back hole is 52mm from the front…
A motor mount for the Tower Hobbies MK1 P51 Mustang. (This is for the older/original version of the Tower Hobbies P51 Mustang, not any of the most recent versions). Depending on your print settings, you'll be between 28 and 40 grams…
The Hobby King Cloud Surfer RC Glider is "lightly constructed". It has soft foam and some weak designs. Consequently, after a few landing, the center landing wheel collapses into the fuselage and no longer works. This design replaces the…
A set of couplers to make inline connection/repair of Zehnder ComfoTubes. Normally when connecting lengths of ComfoTube together, you thread one inside the other, wrap it with tape and put a cable tie on it. That works fine, but it…
When installing a water supply shutoff valve under a sink, it can be hard to hold the valve in place, at the desired angle, while tightening the main compression nut. This tool threads on to the output compression fitting so you can hold…
I have an 8" tablet I'd like to use as my screen with my Hubsan Zino Pro quad controller. It won't fit where the phone normally fits, so I made this bracket to hold it. Edit: I recently switched to a 10" tablet and made a new bracket for…
Thanks to DampSquid for giving me a good start on this project. I re-scaled the design, filled in the anchor and added a hole for an eyebolt. My post caps we're getting destroyed by the sun, so I needed to replace them anyhow. Also, birds…
The Super Best Bottle Opener is great, but my "better half" requested one with a longer handle, so I stretched the handle a bit so it fits further into your hand. I also had problems printing the overhang on the original, so I widened the…
A bracket that attaches to the VESA 100 mount on the back of a computer monitor, and holds a mini computer I make digital picture frames out of old computer monitors and windows mini computers. I was planning to wall mount this one, so I…
A template for the 5mm locating pins on the Blum Bifold lift mechanism. First hole is 37mm from the edge. Second hole is 192mm back from the first. Printed in PLA
Adapter part for Aqua EZ Nylon Pool Skimmer (Originally purchased at Lowes) A part broke on my pool skimming net. I designed and printed a replacement in PLA. I'm not sure how well it will hold up outside in the sun (but it's likely to be…
I very much enjoy the rotary clock, but I wanted some adjustability on the viewing angle. I redesigned the body so that you can rotate the viewing angle a limited number of degrees. I have not fully tested this at all possible angles (it…
Mounting for the AKK fatshark compatible diversity Rx, for the Sentinel Automatic Antenna Tracker Lite. I choose to do it this way, so that we could read the display on the Rx and more easily make setting changes. With the Rx mounted with…
Added a new case, and added an extension to existing designs to protect the lenses from getting scratched. Camera protector for Eken H9 A few misc parts I designed for my SonicModell ARWing. Camera protector for AKASO EK7000 Pro 4K Camera…
UPDATE: After a lot of testing/use, I decided to enlarged the battery opening slightly, and I made the finger grips larger. See version v8. The battery retainer broke on my UR85. It wasn't quite the right size anyhow for the 2S 450mah and…
Spacers for my toilet paper holder so big rolls of TP will fit. The big rolls of Costco/Kirkland toilet paper don't fit on the TP holder correctly. They're too big in diameter (when new), so they pinched against the holder and won't…
A re-working of the Nose Gear on the RC Shark. These pieces replace the "front gear lever" and the "front gear spring" of the standard design. The RC Shark model plane here on Thingiverse is great. https://www.thingiverse.com/make:524192…
Clips to hold foam-board insulation to the bottom of the Anet A6 heated bed. IMPORTANT: If you do this project, you will be putting potentially flammable and electrically conductive material near/on the electrically-powered heated print…
New models (2017 and on) of the Tower Hobbies P-51 Mustang RC plane have an option for retractable landing gear (retracts), which is awesome. Unfortunately, with the gear in the default location, the plane has a tendency to nose-over on…
The original fan spacer works great. I wanted some light down by the print nozzle, so I could watch the print without using a flashlight. I modified the spacer to add an area for LEDs. I stuck a small strip of LEDs on and wired them into…
I lost the battery cover on my iBalance 2600 Digital Scale. I've had the batteries held in with a big piece of tape for a couple years. A couple days ago I realized designing and printing a replacement cover would make a great project.…
I needed to install a compression fitting on a new copper stub-out at a sink. The copper tube was discolored and had gotten paint slopped on it, so I needed a copper tube brush to clean it up for the fitting. I bought one of those…
I liked the original remix, but I thought I'd reduce the weight a little bit, so I made the walls 1.6mm. I also cleaned up a couple misalignments.
The earcup back cover on the Soundbot headphones is held on by 3 screws. For whatever reason, the mounting they screw into broke/split on mine and the cover was dangling by the battery wires. They are rather new headphones, and still work…
These are all currently available results.
