175 models
NOTE: Imported from Thingiverse with minimal updates to description but none to design… I recently purchased a Ryobi 40V weed wacker with expand it capability as my 10 year old gas model was no longer working great. Since I have one more…
I was pretty disappointed with the RYOBI 1800W Powerstation. It didn't come with MPPT Solar charging or even Pass-Thru charging. I was curious if this was a limitation of the 40V battery or just the Power Station. After some quick tests,…
Makita battery holder for four batteries. Works with 18V (LXT) batteries and 40V Max (XGT) batteries. A remix of Jerry's single holder. Supports only required from the built plate to support the joint tags. It can be done without supports…
Makita battery holder with a secure fit. I designed it for a 2.5 Ah battery, as that’s the size I have. I’m not sure if it fits larger batteries. It prints without supports. V2 and V3 have flat sides for easier alignment or for aesthetic…
Updated 05/22/2025 Allows for the use of two Ryobi 18v batteries in place of a 40v battery. Suggested print settings: - 0.20mm QUALITY - PETG (pictured using OVERTURE PETG Grass Green ) - Infill density 20% - Infill pattern Grid - 3…
Ryobi makes several AC Inverters and USB chargers. The 40V battery RYi300BG is nice because it has a 300W Pure Sine wave inverter, a USB Type C port 5/9/12/20 VDC rated at 2A, and a USB type A port rated at 3A. The only down-side is that…
I was not satisfied with the available battery adapters for use in my tiny electric go-kart build. I needed something stiff that I would never have to worry about. Designed for the 40V series of Greenworks batteries. Features polarity…
For stronger holders, print flat with supports. If printed vertically where you don't need supports you end up putting the weight of the battery on the layer lines and you could blow out the bottom of the holder. Thx Okcazure for the…
This is a storage solution to hold your Ryobi 40V batteries. It's a bit over-engineered and more beefy than other options out there. I have some 6aH batteries that are really big that this model holds with ease. It will also fit all 2aH…
Holder for a 40v 4ah Ryobi battery and the slim charger
A wall mount for the Ryobi 40V leafblower that contains a clip/slot mount (as seen in the pictures). This can vary between leafblower models. This was remixed from the referenced model to make it sturdily wall mountable. This is a…
A battery release button for my Kobalt 40v Leaf Blower broke, and there are none online that I can find, nor does Kobalt (Lowes) sell replacements. I have created this in Blender, printed it in PLA and have since used it successfully.
There are two versions, the first version is standard and can be cut to fit smaller printers if needeed ( in slicer cut recommended ) The second version is modified to fit Bambu P1 and X1 or printers with the sane print volume without…
Made this to mount the 40V battery charger from Ryobi. Remixed to allow you to take it off the wall without unscrewing if you needed to. Snap fit! Works great. Wall mount part allows you to screw it in without measuring. Remix of:…
This mount allows the Ryobi 40v Expand-it trimmer to be hung from the wall with the trimmer head still attached. The only holder that I previously found for the Ryobi was for the power head only, but didn't have enough space to allow the…
Update 2024: Since it is impossible for me to control the printers, filaments and slicer settings of those who print my models and having been told that my model is not sturdy enough to withstand drops (it was not designed for that…
I needed to inflate a raft and I had a Ryobi 40V blower. FTIJPI! I printed the first couple of layers to resize the part. I suggest you do the same and simply scale the part. I have also included the STEP and SolidWorks files as well. I…
Greenworks 40V Battery Holder for IKEA SKÅDIS System 04/27/24 UPDATE : I made a version 2 that now has the same alignment plugs as my other Skådis designs, for easier installation. Also threw in a Greenworks logo like the Makita parts. I…
A wall mounted clip for the Makita 40V battery system. Nothing special to print, as the overhang already has pre-included support. I printed it .4 nozzle/.2 height, 20% infill, no supports. As I live in Arizona, i printed mine in a heat…
Updated my 40V Batteries mount for Ryobi Link model by adding a 25 degree tilt to allow for easier add/removal of the batteries. This model allows you to hang three 40V Ryobi batteries using the Ryobi Link system. Printed at .30mm without…
Updated my 40V Battery mount for Ryobi Link model by adding a 25 degree tilt to allow for easier add/removal of the battery. This model allows you to hang a 40V Ryobi battery using the Ryobi Link system. Printed at .30mm without supports…
Wall mount for Kobalt 40V Max 520 CFM Gen4 Leaf Blower
Includes Fusion 360 project
Check out my updated 40V Batteries mount v2 for Ryobi Link model. This model allows you to hang three 40V Ryobi batteries using the Ryobi Link system. Printed at .30mm without supports using OVERTURE Grass Green PETG. Portions of the…
Couldn't find a model so I made one real quick, using it to convert a powerwheels truck from 24v to 40v, used spade connectors glued into mate up to the positive and negative ports, added holes for ¼'x20 bolts to mount it, it's a snug fit…
Modeled with onshape, feel free to remix, link to my drawing is below. https://cad.onshape.com/documents/52dd3a7b840d64e9c8ea258c/w/a0fd00a7e60ab31e420b362e/e/53f1746f45fafb936a6825e7?renderMode=0&uiState=65be84c66471622ccbb0cf19
I dropped my leaf blower and the latch that holds in the battery broke. I submit my replacement, the kobold. What else would you expect from route 3D6? print 100%infill with supports on bed and sand the pins, I had to shoot some wd40 onto…
Check out my updated 40V Battery mount v2 for Ryobi Link model. This model allows you to hang a 40V Ryobi battery using the Ryobi Link system. Printed at .30mm without supports using OVERTURE Grass Green PETG.
Wall mountable holder for Kobalt 40V batteries. Designed to store my many Kobalt batteries up and out of the way by attaching them directly to some 2x4s along my garage walls.
A collection of mounts for mounting Ryobi 40V tools onto Slatwall. I usually store my leaf blower without the battery inserted, just in case the little nub that holds it up can't handle the weight, but so far it seems plenty strong…
This is a full build of a power supply based off my previous 18V version, but that again is off of Volon's original design for the 18V adapter plate. This had a whole new redesign of the adapter to fit properly to the 40V Makita Battery.…
This is a bit holder that fits the Makita XGT 40V max. drills DF001G/HP001G (U.S.: GFD01/GPH01). Holds 6 standard ¼" hex bits securely with 5x2mm magnets. Please read the following guide before printig. German version below. Hi! This bit…
I recently bought Harbor Freight's Atlas 80V lawn mower and wanted to mount it outside of the charger and tool so I made a wall mount for the battery. This mount should work for both the 40V and 80V batteries. I don't have the 40V battery…
Simple Hook for Ryobi 40v Expand-it Main tool Printed PETG Infill Modifier around hook area to 100%
This is a wide nozzle attachment for a Ryobi model#RY40402 40V leaf blower. I made it to speed-up blowing leaves and grass clippings off the driveway. It replaces the original (round) nozzle that is included with the blower. I used two…
I hate the idea of having different batteries for different tools or being locked into a tool brand because you've accumulated their batteries. Ryobi have some great 36V gear (40V in the USA) and I wanted to use my existing Ozito/Einhell…
A mod of the Voron Design Stealthburner and Clockwork 2 extruder designed to suit the Bondtech LGX lite / LGX Lite V2 extruder and Mellow SB2040V3 Canbus board. The Mellow SB2040V3 is quite different to the V2 designs and uses a new…
I remixed this to remove some material, shorten print time and make it look a little nicer with chamfered edges.
Fixed adapter from Makita batteries to Ferrex tools. The shape is specifically designed for hand 5W LED light. Contacts for battery are from aliexpres. The tolerances are low, so the contact block fits snug in the place. Between minus (-)…
Printed in 0.2mm in PETG The assembly is pretty self explanatory and everything is held together with 8 screws. The holes are threaded for M3 screws but fill free to use wood screws as well. This requires 3mm screw with flat heads - you…
This is a flat nozzle for lifting wet debris. It comes in 15 and 20 degree angle versions. As this blower is quite powerful there is a significant torque applied by the 20 degree nozzle. The area of the nozzle is 90% of the normal…
Made this Black & Decker 40 volts max battery holder so i can easily store them and so they can stay at reach. I made these models based on the 40 volts max battery that came with my Black & Decker battery powered tools. The battery part#…
This is a model I made to wall mount my 40v Kobalt batteries. I printed it vertically with 20% infill and no supports.
Remix so I can use it as battery storage on the wall Holes are still there for the adapter, you can choose to not use them credit: Thingiverse remix of thing:4928771
Designing around many complex angles was done by trial and error. If it looks a little cobbled together, it was, but it does give it better support from falling over on uneven ground. Downside: To remove the nozzle tube, the stabilizer…
Created this using initial design phase of the triple battery carrier, that I created for myself, because most people pr
An Ikea Skadis (pegboard) holder for Ryobi 40V batteries. There is also a mount on the side that the charger can be hung on. I designed and tested it with the 4ah battery, but higher capacity batteries should have a similar cross-section…
Battery holders for Activ Energy batteries usually sold in ALDI/Hofer. You can select between two types, one is for vertical and horizontal mounting, the other is angled 25° for easier access
This is an accu holder for the Worx Accu WA3536 Printed without support the way you can see in the picture replaced with version 2… fits better and is more stable
I have some Kobalt 40V cordless yard tools. Cordless tools need battery chargers. Kobalt's 40V battery charger works fine, but it doesn't have any keyholes for wall mounting. I came up with this. You will need to remove the four little…
I needed a way to manage and store my 40V Kobalt batteries. Print shown was completed in PETG. This held up fine in an unconditioned garage during a Georgia summer. I have these spaced 19mm/.75" apart. This allows plenty of room to pull…
This model holds the Hart 40v battery charger horizontally for wall mounting. There is a loop for using a zip tie to fasten the power cable into the channel and there is a pocket to allow the strain relief to bend into place. The cap…
I created this because I need 3 batteries to mow the lawn. It was a pain to carry three batteries in my arms with the potential of dropping one. I printed this with a brim and standard support at 1% density (carrier only). Handle needs…
These RYOBI 18V battery mounts can be bolted down. You can make different configurations to suit your need. I've also provided a 12V socket and switch holder models. For an example, I put together a 2S2P system that has a regulated 13.8V…
Mount for hanging a Greenworks 40V battery on a 3/4" (or 20mm) french cleat. Prints well as oriented in the STL. No supports necessary, low infill. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No…
Hanger for the Ryobo 40v powerhead. Hang your trimmer on the wall. Accommodates a 25mm to 26mm shaft. Hang without the battery attached. Print with PETG or ABS if your garage or storage area gets hot. reccomend minimum 30% infill, 4…
I bought the Hiletgo PWM speed controller to change the speed of a 12 volt fan, but it does not include an enclosure box. It was only a bare PCB Board. This model will house the PWM controller using four pegs that will fit through the…
Print with supports standing up. Should only require a few supports and prints relatively quick considering it holds a huge battery. I printed with 15% infill and it holds up fine.
DeWalt 40v Max charger wall mount plate. My charger is a DCB114 that came with an edger. I printed it with a .6 nozzle and added a 100% infill modifier around the screw holes. Probably not necessary but that's what I did.
Update March 2024: I've decided to move from HSW to IKEA Skådis System . Stronger. Easier. Here's a battery holder for the Honeycomb Storage Wall system and the Greenworks lawn care line. It uses a plug to hold it firmly in place with…
Adapter to use 2.5" shop vac hose parts with a Ryobi 40V leaf blower. There are multiple Ryobi 40V leaf blowers, this was tested with Ryobi model RY404100. It will NOT work with model RY40480. I printed this in ASA with 100% infill and it…
Designed this tiny case with a snap-fit lid for a 2 -channel 5/240V Omron Low-Level Solid State Relay. It has been designed as a very fit, the SSR board and relay modules only just fitting inside. It is symmetrical with cutouts to access…
Walked into Aldi and came out with this very strange power tool battery that can power both 20V and 40V tools. So I obviously made a mount, and added connecting holes for the two positive and negative outputs with the plan to make an…
Greenworks Gen2 40V Battery Charger Mount for IKEA SKÅDIS System New V2 here! This is a Greenworks Gen2 40V charger mount for their line of yard tools (mower, leaf blower, etc) that mounts to the SKÅDIS pegboard with printed M2.5 T-Nuts…
The release clip broke on my 40V Ryobi battery that was past warranty. This print fits perfectly and I hope it helps!
Simple wall mount for a 40V Max string trimmer. You'll need to remove the battery for mounting. See my other designs for a battery mount. No supports. This should be OK with any filament you have - I used a roll of PLA in a color I didn't…
Simple Wall Mount to hold the Greenworks 40Volt Blower. The blower just slides in. About 10hours to print. This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/lfCs7avPZTH Print Settings Printer Brand: Prusa…
Summary Battery holder for Kobalt 40V lawn equipment batteries. The original has 4 screw holes ideally suited for horizontal mounting on either side of a 2x4. This version moves to 2 holes in the middle and includes recesses on the rear…
This is a reinforced remix of the original Ryobi 40V blower wall hanger. While testing the original design, I discovered it also fits the Kobalt KHB-3040-06 electric blower and Kobalt KST-120X-06 trimmer — great news if you run a…
Ryobi makes several AC Inverters and USB chargers. The 40V battery RYi300BG is nice because it has a 300W Pure Sine wave inverter, a USB Type C port 5/9/12/20 VDC rated at 2A, and a USB type A port rated at 3A. Unfortunately it doesn't…
Greenworks Gen1 40V Battery Charger Mount for IKEA SKÅDIS System This is a Greenworks Gen1 40V charger mount for their line of yard tools (mower, leaf blower, etc) that mounts to the SKÅDIS pegboard with printed M2.5 T-Nuts from 6d6178 .…
Greenworks Gen2 40V Battery Charger Mount V2 for IKEA SKÅDIS System This is an improved Greenworks Gen2 40V charger mount for their line of yard tools (mower, leaf blower, etc) that mounts to the SKÅDIS pegboard with printed M2.5 T-Nuts…
My copy of the Makita XGT 40v terminal block I made in fusion For the tabs I used copper pipe flattened out and cut to 17x18mm
This adapter is intended as a basis for other designs. It affixes to the 40V Ryboi leaf blower model RY40402VNM. Original idea for a duster nozzle required too sharp a taper to work properly, but figured the adapter part might be useful…
A simple wall outlet without grounding. In Holland we have 2 different wall outlets. One with grounding and one without. This one is without. The first one I shared was to tight, now the plug can be smoothly inserted. No need for support,…
Bronk's design was a great start, but they didn't have access to an actual mower to test it. I adjusted it to properly fit my Worx 40V lawnmower. Also added holes for an optional string or keychain, and a hole for an M2 20mm machine screw…
Ryobi Adapter more space for cables Ryobi glue or press on logo
I liked this model but needed to mount it to my multiboard setup. I modified it to mount to multiboard using 2x bolts for extra strength. Works with both my Ryobi 5 Ah and aftermarket “6 Ah” batteries.
Requires (4) M4x14 OR M4x18 bolts, (4) M4 nuts, and (4) mounting screws, I used 1" drywall screws. Orient parts so that no support is required. Be sure not to over-torque M4 bolts to avoid layer separation. Tested with 4Ah battery, holds…
This is a modified version of the flyeddy_v21 mount by Hammelbein which is compatible with the v3 Fly Eddy board.
Mounts a B&D 40V Max battery to your Multiboard. The mount is 10mm deep, and the multiboard is ~6mm. I used the 20mm large shank bolts from the standard Multiboard library (not included here). It's purposefully slightly wider to…
Printed this out of PLA. No brim or supports needed.
Since Ryobi doesn't cool their batteries in any way, my lawnmower cooks them. Earlier I made a vented battery shell for my 7.5Ah battery & so far I've gotten around ~30% more battery life out of it as a result; with it being cool to the…
This model uses the popular 30 mm diameter USB car charging socket to provide USB power from both Ryobi 18 volt and 40 volt batteries. The charging socket I used was the only one I found that had the input voltage range for both the 18…
This is intended to be used with the honeycomb storage wall https://www.printables.com/model/152592-honeycomb-storage-wall Included is a screenshot of the print orientation I used with organic supports only needed for the honeycomb wall…
Ryobi 40V Lithium Battery USB-C PD Power Bank Adapter Enclosure Parts: [10AWG Adapter for 40V Ryobi Lithium-ion Battery](https://amzn.to/3CjG3Ay) [High Voltage USB-C PD Outlet](https://amzn.to/3DUMg6g) Wire cutters, strippers, connectors,…
I added a pi for octoprint and need a way to power it. This was my first 3d so keep that in mind it seemed to work
I needed a holder for my Lithium-Ion batteries 40V to fix on the SKÅDIS pegboard The batteries are rebranded for LANDI Okay 40V 2.5 Ah having model number R3-360-AH-U-01 The holder uses a dovetail system ( Skadis Dovetail Peg System )…
Description: Durable battery mount designed to securely hold and stabilize a Matrix X-ONE Li-ion battery (e.g., 20 V or 40 V system). Ideal as a replacement part or custom mounting solution , this holder ensures a tight fit and reliable…
I needed to hook up my table saw with my Ryobi 10gal shop vac. Tested with: Saw: Sawstop Jobsite Pro Vac: Ryobi 10gal wet/dry shop vac (40v) (Yes, I know a shop vac isn't the best - its what I have right now)
Allow me to introduce you " Voltage Tester 1.5-40V 1.5A - Case STEP-DOWN LM2596 + voltmeter ". I assembled this project because, had a lot of schemes with adjustable voltage. I needed to know exact voltage of each and decide to use LM2596…
If you want to leave the printer's power supply inside of the HomeCube use this cable grommet for the 240V power supply cable. For my power supply cable I need a 30mm borehole so that the plug fits through the hole. The outer ring of the…
Wall mount for 40v Hart battery. Slide in from top. Non-latching. Printed in PLA, no supports
I recently bought a "LED Power Supply" from eBay for my LiPo charger, and found the instructions and STL from bastian___ - but unfortunately that cover didn't fit my PSU, so i designed a new one. The PSU has the model number DY01, accepts…
Ryobi 40V battery mount compatible with the DDD Printable Wall Control System ( https://www.printables.com/model/52618-ddd-printable-wall-control-system Additional parts needed: A left and right 3x0 DDD Flat for mounting. Six (6) 4x8x10mm…
I was inspired by some other holders, so I decided to make me one, that would fit with my IKRA battery. Since I haven't found any on the internet I made one in TinkerCAD. It's simple to make without any supports or brim. Just use standard…
IMPORTANT UPDATE : there is a V2 of the spacer that provides way more stability (just make the bar 90 degrees off from those 2 posts just like the V1 version) it it prevents the blade from oscillating about the x-y plane over those little…
This is a heavy-duty mount for the Ryobi pole saw head. Storing these can be a pain because they're top-heavy: Locking Version: This one has a specific "lock-in" tab at the bottom to prevent the mount from flipping up or shifting when…
ABOUT: Looked all over and couldn't find a specific trigger for my tool. So I made it. Both versions work. V2 is just a little more sexy looking. =) PRINTING SUGGESTIONS: I would use ABS or PETG, It shouldn't take more than 1hr to print.…
When installing a MicroAir thermostat in my Alliance Valor 40V13, the trim work got in the way. Rather than trimming the trim work, I created this adapter plate that I screw into the wall, then use 3M Command Velcro strips to mount to the…
