P
Printables
HELIX COMPOSE CiX E50FM-S4 Cover
The cover must be printed with support material. It is recommended to use only ASA and a layer height of approx. 0.16 mm.
Search results: e5
Counting matching models…
P
Printables
Brother PT-E550W Case Latch
Printed using PETG, but any material should be fine. You'll need a little bit of flex to get the latch onto the corresponding pins of the hinge. On the hinge, enable “Supports on build plate only”. On the latch, I used paint-on supports…
P
Printables
Preh ME5A Latch Plate (improved)
I had a broken Preh ME5A switch which would no longer correctly lock into the switched on state. Luckily this video by DIY Chris existed, which explained the issue and offered a solution. The little plate with a peg, which is responsible…
P
Printables
Karcher SE5001 spare part
Spare part for KARCHER extractor Printing Material - PLA, PETG Layers - 0,2mm Supports - YES Other info I recommend printing at 99%, I made the model with the dimensions I measured and it is quite tight in the hole.
P
Printables
DDD Dewalt Grabo lifters DCE592B vacuum clamping system
This project provides the models for a printable vacuum clamping system utilizing the Dewalt Grabo DCE592B lifters. All fittings are ¼" push connect lines and ¼" NPT thread. BOM Dewalt Grabo DCE592B lifter Minwax Polycrylic sealant 1/16"…
P
Printables
Charge Cover Renault Zoe ZE50
During a charge where it rained very hard, the soft material on the inner lid became soaking wet. Several hours later, the car failed to charge, likely due to moisture in the port. This cover shields the charging port from rain and snow,…
P
Printables
Dell Latitude E5440 Laptop Hard Drive HDD Caddy Caddie
Printed in a Prusa mini+ Print settings: 0.20mm QUALITY PLA filament Supports: None Infill 15% Used Filament 1.92gr print time 14 min
P
Printables
Dell Latitude E5430 Laptop Hard Drive HDD Caddy Caddie
Printed in a Prusa mini+ Print settings: 0.20mm QUALITY PLA filament Supports: None Infill 15% Used Filament 1.92gr Printing time 14 min
P
Printables
Brother E550W/PT-H500 bracket for Multiboard
A bracket to hold the Brother E550W/PT-H500 label printer (P-touch system) on a Multiboard wall. Note: This will not work with the Brother P-Touch E560 which is slightly larger. You need two or four Multibuild Lite Fix Points to attach…
P
Printables
Acer Aspire E5-774 series charging cable port movement blocker
When the charging cable keeps falling out or never quite connects put this tiny part in the gap near the charging port to fix it from moving if the tiny plastic bits are broken off from cable's sides or the casing is damaged in a way that…
P
Printables
NVMe fan for Machinist X99 E5-MR9A Pro
The purpose of this project is to increase airflow and lower the temperature of the NVMe slots on the Machinist X99 E5-MR9A Pro motherboard by adding a dedicated fan. Before utilizing this solution, average NVMe temperatures of 60 °C were…
P
Printables
VRM cooler for Machinist X99 E5-MR9A Pro
The stock VRM cooler on the Machinist X99 E5-MR9A Pro uses a very poor-quality fan, developed an annoying rattle, and is overall inadequate. This project replaces that stock cooler with a mount for 2x 40x20mm fans and copper heatsinks.…
P
Printables
Renault Zoe PH2 ZE50 ZE40 Wireless Charger
My charger is 102 mm in diameter. Used doublesided tape to mount the charger to the body. Not sure if the side braces are needed.
P
Printables
Starseeker E55 Coffee Grinder Portafilter Holder
Portafilter holder to be mounted on the Starseeker E55 to grind straight into the portafilter. The model fits multiple versions of the 58 mm E61 standard (depending on the diameter of the out portafilter). The model still allows for the…
P
Printables
Bosch (Rechargeable vacuum cleaner MOVE 2in1 BBHMOVE5N) attacment nozzle extender
It’s the attachment nozzle of the Bosch (Rechargeable vacuum cleaner MOVE 2in1 BBHMOVE5N) handheld vacuum — the little piece you clip onto the mini‑vac to focus the airflow. Used for: - getting into tight spaces (corners, sofa creases,…
P
Printables
SKADIS Holder Battery Charger Canon LC-E5
SKADIS Holder Battery Charger Canon LC-E5 Use Skadis T-Clip System - Low Profile Flush Mount Clips Dimensions:
P
Printables
Zyxel BE5100 BE6500 wire cover
No hardware cover for the BE5100 and BE6500 access points by Zyxel. It is held in place with pins that extend into the screw recesses I printed mine in PLA with the top PIN SIDE on the plate and internal organic supports. The cutout is to…
P
Printables
NE5532 mixer enclosure
Small enclosure box for NE5532 mixer boards, which you can get for cheap from Aliexpress. The lid is really simple and has to be put with M3 screws. For keeping the board itself in place I made some 3mm holes to also fit M3 screws. All…
P
Printables
OnePlus Nord CE5 Phone case
Impact resistant with corner bumpers that leave a gap for extra cushion from falls. Printed in TPU 95A with enough walls to make everything completely solid. Print with the camera side up with supports to hold up the honeycomb mesh back…
P
Printables
Dewalt Grabo lifters DCE592B vacuum clamping system REMIX
Dewalt Grabo lifters DCE592B vacuum clamping system REMIX Total credit goes to DDD Dewalt Grabo lifters DCE592B vacuum clamping system by luma | Download free STL model | Printables.com by LUMA Restriction by Luma’s project is you need to…
P
Printables
Mercury One Skirt E5 (squash ball) Rear Corner w/power input ONLY
For my ender 5 pro upgrade journey, I re-located the power switch to the front of the machine. I love this skirt upgrade and wanted to keep the aesthetic of it intact while removing the blank hole where the switch had accommodations for.…
P
Printables
Repuesto Cascos JBL TUNE510BT
Hoy os dejo una reparación de unos cascos bluetooth JBL TUNE 510BT de mi hija. Para arreglarlos hay que desoldar algunos cables como comento en el video.
P
Printables
Dell E5570 Vertical Stands
I needed to free up some space on my desk at home to work more comfortably in smart working, so, since I have a monitor and a keyboard, I decided to put the PC vertically. It is definitely inconvenient to turn on the pc but I never turn…
P
Printables
Rocker Molding Clip - Mazda (NE56-51-SJ3A)
These retainer clips go on the bottom of the rocker panel.
P
Printables
Huawei E5577C Mounting Bracket
I printed it lying on the back side with supports everywhere.
P
Printables
SR Suntour FEE501 replacement
Replacement FEE501 part for SR Suntour XCM (older version - may not fit newer one)
P
Printables
Apache550_RAK_2X18650
Print this out of ASA or ABS. Insert fits the Harbor Freight Apache 550 Cases here: https://www.harborfreight.com/550-weatherproof-clear-case-56378.html Their SKU is: 56378 Use M3 Self-Tapping screws to mount a RAK19007 Baseboard into the…
P
Printables
Stihl FSE52 grass trimmer wall mount
A wall mount for a Stihl FSE 52 grass trimmer, may suit other models as well. prints without supports, I used PETG
P
Printables
Swivel Bracket for MikroTik SXT Lite5
The standard MikroTik Bracket fastens around a pole with a clamp. I wanted to mount it in a protective cabinet against a wooden board. Also needed to point it at an angle. The standard bracket was also too high to use in cabinet. First…
P
Printables
Dewalt DCE570B 10oz Conversion Adapter
DCE570B typically takes 29oz tubes this adapter allows for standard home caulk tubes to be used. The front and rear shim “may” be unnecessary however they help with racking when the tube is under pressure
P
Printables
NE555 Scratcher
Well, what can I say. Enjoy. Print with the text facing down without supports.
P
Printables
HELIX COMPOSE CiX E50FM-S4 Cover
The cover must be printed with support material. It is recommended to use only ASA and a layer height of approx. 0.16 mm.
P
Printables
Camera Mount - Creality E5S1
A fairly simple mount for a timelapse camera [Brinno in my case from another project] to attach to the vertical legs of my Ender 5 S1. It clips into the groove of the aluminium extrusion, and can be additionally secured with cable tie in…
P
Printables
Netgear AXE5700 (MS90) Wall Mount
This is a simple wall mount for the Netgear Nighthawk Tri-Band 6E Mesh router and satellites (same size). You'll recognize it by it's square shape. This simply allows you to mount the router. Prints bottom-side down. No supports needed.
P
Printables
Brother PT-E550W Case Latch
Printed using PETG, but any material should be fine. You'll need a little bit of flex to get the latch onto the corresponding pins of the hinge. On the hinge, enable “Supports on build plate only”. On the latch, I used paint-on supports…
P
Printables
Tapa Breaker Ecooter E5
Diseño de un repuesto para la tapa que cubre el breaker de las baterías de la moto eléctrica de la marca Ecooter modelo E5 y E5 Pro.
P
Printables
Tlianglelab MatrixExtruder Sinple5015FanDuct and bracket
Simple 5015 fan duct for Matrix Extruder
P
Printables
Headset Hanger Flexispot E5
Printed in PLA with 0.6 Nozzle, 0.44 Layer Height, no supports and 3 Perimeters.
P
Printables
MikroTik SXTsq Lite5 antenna holder
Simple holder for MikroTik SXTsq Lite5 antenna. No adjustment (it can be done by redesigning the fix part). My printing setup: Material: Prusament PETG Nozzle diameter: 0.4 mm Layer height: 0.25 mm QUALITY Infill density: 30% (Gyroid)…
P
Printables
Hifiman HE560 earpad spacer
After recently purchasing a set of used Hifiman HE560 headphones, I found that after a while the inside of the drivers was pushing on the outside of my ears. A simple solution is to add a little space between the driver and pad, which is…
P
Printables
APC PME5B Wall Mount
Remix of Micke's KOPPLA-wall mount to accomodate APC Surge Protector PME5B power strips.
P
Printables
LED Christmas tree powered by NE555
EN: Component list: 7x LED (red, yellow or green recommended) 1x NE555 1x Capacitor 2,2uF/25V 2x Resistor 100R/0,5W 1x Resistor 47kR 1x Switch 1x 9 Volt battery connector 1x 9V battery Printing info: Printer: Ender 3 BL Touch, Infill: 15%…
P
Printables
HDD SSD Hard Drive Caddy Bracket for Lenovo Thinkpad T470 T480 T570 P50 P51 P70 P71 P72 E460 E580 E15 R14 E14 T14 S3 Caddy Holder
2.5" Drive HDD / SSD Laptop Drive Caddy Disk Tray Bracket for Lenovo ThinkPad. Compatible Models: For Thinkpad T470 T480 T570, For Thinkpad P50 P51 P51S, For Thinkpad P70 P71 P72, For Thinkpad E460(NOT E470)， For Thinkpad E480 E485 R480,…
P
Printables
Preh ME5A Latch Plate (improved)
I had a broken Preh ME5A switch which would no longer correctly lock into the switched on state. Luckily this video by DIY Chris existed, which explained the issue and offered a solution. The little plate with a peg, which is responsible…
P
Printables
Extruder Knob E5p with rotation indicator
Medium sized Extruder knob with a rotation indicator. Rotation Indicator: Fill the small hole with a droplet paint. Mount the knob if needed with a M3 insert. Usefull for any Extruder with a Dshaft of 5mm. Tested on Ender 5 pro. Check…
P
Printables
Bushing for Hifiman HE560 (v1) headphones
Do not use vase or spiraling contour mode. Print at slow speed. As mentioned in the title, these bushings are for the Hifiman HE560 v1 model.
P
Printables
Table decoration (chinese5)
Decorative object for the New Year's table (Chinese New Year). I printed it (x-70%, y-70%, z-100%), I think it's a good size and it will take 1 hour and 30 minutes. I think the time is acceptable. Happy Chinese New Year!!!, and enjoy it!!!
P
Printables
Wired replacement battery Canon LP-E5 for EOS DSLR
The Rebel XSi DSLR on the shelf had not been used in at least 5 years and the original battery pack was long dead. The Canon official wired battery replacement or new battery packs have been out of production for years. I could buy a…
P
Printables
Karcher SE5001 spare part
Spare part for KARCHER extractor Printing Material - PLA, PETG Layers - 0,2mm Supports - YES Other info I recommend printing at 99%, I made the model with the dimensions I measured and it is quite tight in the hole.
P
Printables
Hilti TE5 case latch
This is a replacement latch for the older Hilti TE5 case and possibly other Hilti cases using the same design.
P
Printables
Reolink E540 -40 degrees bracket. Mocowanie do kamery Reolink E540 -40 stopni
Reolink E540 -40 degrees bracket. After mounting the camera, it allows you to set it for downward viewing, e.g. when mounting it at a high altitude. The holes are matched to the factory bracket mounting spacing. Mocowanie do kamery…
P
Printables
ZeroG E5P Filament Sensor Mount w/ Double Compression Fittings
I currently use an Eibos Cyclopes filament dryer, but the bowden tube coming from it did not connect directly with my filament runout sensor. I found Matt M's model that added the compression fitting to one side and modified it to have…
P
Printables
Voron 2.4 PTFE Tube Pass Through using GE5C Radial Spherical Bearing
This is a great way to get the PTFE into the chamber if you are planning on using a ERCF. You just need some (2)M3 X16 mm Screws and (2)M3 Nuts. I am going to add a version with threaded inserts as well. I ordered HiPicco GE5C Radial…
P
Printables
GE5C Z Joints REMIX
I was having problems with the magnets not triggering the Hall XY limit switches, so I changed the position of the magne
P
Printables
TP-Link Deco XE5300 Wall Mount
I wanted a wall mount that keeps the router a little further away from the wall surface, to help with signal reflection and obstruction as much as possible. I used random #8 wood screws that I had on hand. One screw is likely enough to…
P
Printables
Cubierta Pantalla Moto Ecooter E5
Cubierta para display de la moto Ecooter E5 de sumco. Imprimir en PLA translucido y en el software de laminación de la impresora 3D, y en las capas superior e inferior, usar el patrón concéntrico y 0 capas de la superficie superior del…
P
Printables
Helix CiX E50-S4 Exciter Stand
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
P
Printables
Aprilia Tuono V4 1100 Factory E5 Spiegeladapter
Adapter zur Anbindung von Lenkerendspiegeln an der Aprilia Tuono V4 Euro 5. Durchmesser 30mm.
P
Printables
Belt clamps adapted for TorxFighter GE5C and Beefy Idlers on Voron ChaoticLab Carbon Fiber Bracket Kit
This is a set of adapted V2 BeltClamps if you use the ChaoticLabs Carbon Fiber Bracket Kit together with TorxFighter Zero offset Clamped GE5C Mount for Voron 2.4 + Beefy Front Idler The V2 BeltClamp design is used where possible and the…
P
Printables
Box pro wifi spínač Sonoff re5v1c a lišta pro upevnění kabelů
Jedná se o krabičku pro upevnění WiFi spínače Sonoff re5v1c včetně lišty pro případnou montáž. Na lištu se dají zároveň upevnit i kabelové svorky (dle foto). Pro sestavení krabičky jsou třeba imbus šroubky M 3x12 (DIN 912 3x) a čtvercové…
P
Printables
TP-Link AXE5400 Wall Mount Bracket
Hi! I was tired of worrying whether my WiFi booster would fall off of the wall recepticle so I modeled this neat little bracket, it simply attaches to the wall with standard sheetrock screws. Both brackets work, I decided to use the V1…
P
Printables
NE555 Fridge Magnet
The Body.stl part has 4 holes in the bottom for 13x3mm Magnets. The Body_closed.stl has holes inside for mid print placement. Set the Pause hight to 4.2mm When you want to change the color for the NE555 Text, you need to stop at 24.5mm…
P
Printables
Venom Face by dode513
I think that you can make a cool 2 color print with this, enjoy ! I don't know how to make them fit perfectly, but if you know a minimum of 3d modeling, I think you can do it. I created to make a sticker, so don't judge me :))
P
Printables
AmScope ME580 Microscope Rotating Stage Inserts
I recently got an Amscope ME580 ‘metallurgical’ microscope. I'm an electrical engineer/RFIC designer and my main use of [this] microscope is to take photos of and analyze integrated circuits… Unlike biological/metallurgical samples,…
P
Printables
AmScope ME580 Microscope Integrated Filter/Polarizer/Diffuser Storage
‘Integrated’ storage for your polarizers, filters, etc. Holds 8 pieces… Designed for ME580 scope, may fit others… Attaches to scope using existing threaded holes and a couple M3 x 8mm bolts. Printing: No supports required. Re-orient model…
P
Printables
Modified Creality K1 Max Hunter F1715HE5 HEPA Filter holder
I liked the HEPA filter holder design from: https://www.crealitycloud.com/model-detail/65ad2a306215a15789505406?source=5 However, the interface to the printer required double-sided tape. I also liked the following design:…
P
Printables
E5 blaster for B1 droid
E5 blaster for B1 droid 45cm https://www.printables.com/model/1300564-star-wars-battle-droid-b1-real-size
P
Printables
Propeller protector for Drone Pro/E88/E99/E58 - Nubs removed
A propeller/wing protector for the inexpensive Drone Pro/E88/E99/E58 drone. This drone is a knock-off of the toy quad-copter, the “Eachine E58”. You can easily find this USD $20 drone on marketplaces such as Temu and AliExpress. Tested…
P
Printables
NC MX-5 Miata FE51-ST-232
See The reddit link below for reference on the part. I printed at 100% infill with PETG, though another material may be superior. Mine has held up for eight months as of June 2025.…
P
Printables
Alpicool GE50 Divider compressor fridge
I needed a divider for the smaller and the bigger part of the fridge, that goods do not fall down. Added cutouts for better ventilation. Printed with PLA at 0.25mm Layer height and 0.4 nozzle.
P
Printables
huawei e5573 battery dummy
I get the idea from this forum thread: https://www.hovatek.com/forum/thread-38775.html I used 2x 1000uF/10v electrolitic capacitors in paralel, 10k resistor, 10ohm resistor and piece of copper wire. After soldering everything I covered…
P
Printables
Flexispot E5 Lite Button Guard
Simple guard to prevent your chair ripping of the buttons of the control panel.
P
Printables
Huawei E5783-230a Wifi wall support
DE Ein einfache Möglichkeit um den Mobile WiFi Huawei E5783 an einer Fläche zu befestigen. Ich habe mir das konstruiert um den Router in unserem Wohnmobil sicher mit Doppelseitigen Klebeband zu befestigen. Zusätzlich ist auf der…
P
Printables
Nissan e51 universal air filter adaptor plate
Plate size 95x95mm Bolt pattern size 76.5 mm between centre of bolts Outer diameter 89mm or 3.5 inches Part not sitting close to engine. But still recomend high temperature resistan filament. No support needed.
P
Printables
Frame Braces for E5+ with frontbar relocator
Frame braces that tie into the front bar when you've installed @fadedhero636's Ender 5 front bar relocator . The top front bar gets lowered by this mod and doesn't hold the front uprights apart as solidly anymore. Adding these corner…
P
Printables
E5 Shinkansen (N Scale)
I wanted to make a decoration of the E5 for my desk, which I thought would have a model available due to its popularity… To my surprise, there was not! only paid models for a large amount of money (sometimes over 70 USD!) So I made my…
P
Printables
Dell Dock spacer for E5450, E5470, E7240 E7440 etc.
IMPORTANT: while this part fit perfectly for me, people in the comments report it's too long. It was printed on my old printer that perhaps wasn't well calibrated, so if it doesn't fit please try the remixed version that's a little bit…
P
Printables
Intel XEON E5-XXXXV3
I had a Intel XEON E5-2673V3 lying around, then I measured it and modeled it. It should fit as a dummy (for slot protection)
P
Printables
Guide pare choc Ar X5 E53
Vous en avait marre d être pris pour un mouton par Bmw et acheter cette pièce plus de 60 euro? alors n hésiter plus et télécharger mon fichier Imprimer en petg 100% de filament , plateau chauffant a 70 degrés , buse a 230 degrés. temps d…
P
Printables
Mazda Striker Hook NE51-R1-344A
This is the hook that keeps the soft top down when stowed. Mine snapped and it was more convenient to model and print a similar enough version. Costs about $15-$30 depending on your local dealership or factoring in shipping.…
P
Printables
Water tank funnel for Xiaomi Robot Vacuum E5
Description: This custom funnel fits perfectly into the Xiaomi Robot Vacuum E5 water tank opening, making it easy to fill without spills. Works great with water filter pitchers (like Brita) or tap water - no more struggling with the tiny…
P
Printables
Passive speaker - folded horn - Phone / Iphone5
Passive speaker - folded horn - for Iphone5/6 i made this to fit my Iphone5s with cover. Inspired by Fab_ster, design in Dec 11, 2015: https://www.thingiverse.com/thing:1191352 Opened he's design in Cura for printing, the printing time…
P
Printables
Asus RP-AX58 / RP-BE58 Range Extender Repeater AiMesh Node Stand
UPDATE V2: I adjusted the length of the foot for better stability and added some material above the plug mount for better strength. The side contours have been adjusted for aesthetics. The RP-AX58 is an excellent value for those who need…
P
Printables
iphone5 SE cover/case - Dovetail
Iphone5 SE Dovetail cover/case. (fixed and strengthen) reinforced models, with or without side-ring for string or chain.. different models.. These here is made in Tinkercad, better and more precise design made with Fusion360 is found at:…
P
Printables
Roomba irobot i7 e5 gears
Gears for the rubber brush drive mechanism. If the socket for the square or hexagonal pin of the rubber brush is damaged, the roller will stop rotating and Roomba is no more capable of picking up the dirt from the floor. Repair requires…
P
Printables
Flir Exx Series E53, E75, E85, E95 Thermal Camera Lens Cap
This is a lens cap for the Flir Exx series handheld thermal imaging camera This cap should fit: E53 / E75 / E85 / E95 E54 / E76 / E86 / E96 Step files attached.
P
Printables
DDD Dewalt Grabo lifters DCE592B vacuum clamping system
This project provides the models for a printable vacuum clamping system utilizing the Dewalt Grabo DCE592B lifters. All fittings are ¼" push connect lines and ¼" NPT thread. BOM Dewalt Grabo DCE592B lifter Minwax Polycrylic sealant 1/16"…
P
Printables
Flir Exx Series E53, E75, E85, E95 Thermal Camera USB Brace
This is a USB Cable Brace for the Flir Exx series handheld thermal imaging camera. Just like the Flie E series, there is a bit too much pressure applied to USBc cables when plugged in, so this reduces the pressure put on cables while the…