102 models
Yet more DJI Mini/Mini 2 Landing Gear Extensions. These are light, about 5.5 g for all four. They add about an inch (25mm) to the height. I used PETg, but they should be fine with other materials. I used .20mm layers. Could have used .15,…
Remixed from bbeavis design (https://www.thingiverse.com/thing:3063090) I printed his but it was too thin, so I decided to beef it up and also change the design. It's also 2cm longer to be closer to your shoulder. I advise you to print…
Printed upright with no supports. Large sticks can be removed using an m3 screw down the centre, to push the original stick out. Or use the steak knife method by gently cutting a split and they remove nice and easy. I cleaned the inside…
I 3D modeled the legs that came on my Two Trees TTS-55 Pro and added a 3/8-16 thread to the bottom to add extension risers of various lengths. The extensions are 10mm, 20mm, and 40mm columns with the same 3/8-16 thread. I also made a…
These slide over the factory rear vents to extend them past and over the floormats to increase cooling to the back seat. I suggest printing them in PETG or ABS so withstand the heat from a car. I will be adding models with more options at…
Logitech Paddle Shifter Adjustable Extenders These clip-on paddle shifter extenders offset the stock paddle shifter to better fit aftermarket wheel adaptations. These are designed to fit perfectly with my other hot swap wheel connector…
Huge thanks to Ryan of V1 Engineering, the Generous Genius, for sharing his wonderful machine designs with the world. This is a remix set related to the amazing LowRider v4 DIY CNC . For orientation on what is meant by “front” of the…
These models extend the handlebars of a G30P 25mm for better control. For use with stock grips. This update vastly improves rideability of the scooter. Snug fit, will require a rubber mallet and finesse. I suggest printing more than two.…
I did found one similar model, but it was way to small - couldn't push them on extrusion and rubber feet didn't fit also - so I amde my own :) For ender 3 v2 users: remove PSU (black) cover, the PSU will become cooler and then the feets…
Note: I had to print it at 105% scale for it to fit properly, however I don't know if this is an issue with my printer or controller so I'm keeping it the same size as the model I'm remixing. I've been playing a flight sim recently and…
Axial SCX6 battery extenders for the Gens Ace Bashing Pro 157mm 3S (8000mah and 6700mah) packs and the XL version for Gens Ace Bashing Pro 178mm (15000mah). New - Looking to get these tray extenders, but don't have a printer? Checkout my…
Mazda MX-5 Miata seat belt extenders for the NA/NB models.
Hi there! After levelling my heatbed, I noticed that the back build plate stops were a bit short. Sometimes, the build plate would sit on them, causing it to be slightly raised in the back. To solve this, I designed some build plate…
Mavic Mini Joystick Extenders I wanted longer joysticks for better precision with my Mavic Mini. I designed these extenders to fit over the stock joysticks. Leveraged the foam on the original sticks to create a nice snug fit. I have a…
I made these Flightfin extenders for some people and figured I could just share the design with the world. Yes, the bottom is flat and that isn't as nice as having a curve there as well. The thing is, it is so much easier to print them…
To install, Unscrew the mag base. Then screw the new one in (super simple). The extenders are somewhat untested, let me know if there are any issues.
New Version 1.1 Note: In September, 2023, a fellow V1E maker ( @steved on the V1E forum ) needed a little bit of adjustability on the location of the right-side belt-tensioner+endstop mounts, and so I made a v1.1 remix of this design ,…
Designed to fit Ikea lack table legs and extend thier height multiples can stack together. 2 legs and one foot is the same height as one ikea lack leg so you can mix and match as you see fit (foot is optional) Designe to print with 5%…
I use bar end extenders on my bicycle's straight handlebars. I wrap the extenders with padded tape (for cushioning). Recently on a ride, the compression fit end plugs that were provided with the extenders came loose and the tape started…
Thumb stick extenders for the PS4 DualShock 4 controller, available in three different height options. Surprisingly comfortable. ATTENTION! Be careful when putting on, or else you may tear the rubber on the tumbstick.
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
NOTE: In September, 2023, a fellow V1E maker ( @steved on the V1E forum ) needed a little bit of adjustability on the location of the right-side belt-tensioner+endstop mounts in his metal-strut-based LowRider, so I made this v1.1 remix of…
The Stryfe Heel extends the trigger grip of the Nerf Elite Stryfe to fit adult hands. Luke has always had a problem with his hand sticking off the bottom of the grip, so this was the perfect solution. It fits very snugly with a hidden M3…
Simply print one out, attach it to your Xbox controller, and enjoy your game.
I acquired a bigger number of IKEA pencils but they are way to short to write with, so i designed these extenders. One is for one pencil, the other one combines two pencils at the back. The single-pencil extender prints without supports…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
These are 1x2 gridfinity modules. Their function is to be an angled baseplate. They are low, but they will still raise up any module on them as well as angling them forward. There are versions with angles in 5º increments up to 20º. This…
This is the design for parabolic reflectors for a DJI Mavic Pro (original). I assume that it will fit other DJI drone controllers as I think most of them use the same antenna design. It can be printed in a single piece with no supports or…
These are extenders and snap together to add some extra length for 12" and 24" Cricut mats on the Cricut Maker. All versions can be “rocked” into place. To separate, just slide apart sideways. Version 1.2 and 1.3 have a more solid…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
The Dual Screen addon blocks the power / volume buttons when used with the Retroid Pocket Mini, this is a janky fix. Can't really think of a way to have the volume-up button as stable as the other two, and honestly the power button was…
This is the “WOOD INSERTS EDITION” of LowRider 3 CNC - table extenders to use LR2 table (with metal struts) with LR3 - endstop/tensioner supports . It serves the same purpose as the original design — enabling use of metal struts (aka…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
Just some gimbal stick extenders for RC Transmitters that take m3 screws/threading. STL uses a m3*10 screw with 2 m3 nuts (see images). I used cheap superglue to put the two pieces together and they have yet to come apart. Only tested on…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
>print >for the middle hole use M2.5 screw and nut on the middle or use glue >two holes on the sides for screwing it in place >voila Printed on: Ender 3 V2 | PLA+ | 0.2mm | 10% infill | Brim
use a tiny dot of hot glue on an xbox one controller and it will extend the buttons for the device
Snap-on trigger and shoulder extensions for the Nintendo Switch Pro controller. This modification allows for easier use when the controller is being used on a tabletop . nondestructively attaches to the controller and can be easily…
One of my Polarpro leg extenders broke and Polarpro no longer sells them. So I made a replacement. This leg extender slips onto a front leg to raise the Mavic 2 up off the ground. You'll still need the rear leg extenders. These extenders…
These are just hole insets of the “whack a mole CATtoy” for preventing the moles from being stuck when they are being pushed too far in. The extenders have cutouts for allowing the arms to go all the way up. For this reason I recommend…
Added Y-rail clips for 32mm tubes, and Y-rail unistrut-placement-jig for 32 mm tubes. NOTE: tested by a fellow maker, and reported as working. Kudos and thanks to Spadman , @Spadman_112096 , for doing the testing. NOTE: I encourage new…
These were made to elevate my Sovol SV05 to a height which will allow me to install a couple modifications I make to all my printers. Beneath the frame is where I like to install SD card reader extensions, a power switch, and a volt meter…
A small set of pencil extensions, made to fit the classic Staedler. The internal part is tapered, so it should fit other kinds of pencils (but you can always scale the model before printing). The set includes a basic one, one with a…
English : I created this Ikea Adils desk stand extension (or other 40 mm diameter stand) to raise the desk by 45 mm. Français : J'ai créé cette extension de pied de bureau pour pied Ikea Adils (ou autre pied de 40 mm de diamètre)…
It is recommended to print the model using a strong, engineering-grade plastic or to mill it from metal.
JEEP Renegade rear license plate mount extenders for M6 nut to be pressed in. Allowing to mount standard sized US WA license plate firm using all 4 sockets. M6 nuts need to be pressed in using vise (I'm using large pliers). You also need…
Compatible with standard 1/4" (6.35mm) bits and precision 4mm bits , made for IFIXIT Screwdrivers in mind, but should be fairly universal. Extenders come in SLIM and SEMISLIM versions tailored for tight spaces. 35mm to 125mm sizes. 🖨…
Our new utility tub legs needed to be extended about 6 inches. So I designed these. these legs are 155 mm tall
Screw down the foot holders to keep the B1 in the same place while raising or lowering it. After installing the feet, I engraved a grid to the surface so I know where it is lined up. There are leg extenders that raise it 60 mm (2.36”) and…
Print with 4 walls @ 215c with PLA for best layer adhesion. 25% infill gyroid. I have tested these to be an extremely precise fit with my ender 3 v2 to some ebay carbon fibre bars, I also made another version fitting to a common ID on…
-Paddle Shifter Extenders For Moza ES Wheel that you can screw on, bolt on, or tape on. (uses M5 bolt/screw) -Changed these to make them larger for use on larger 13-inch wheels. -Also changed the pin setup for an M5 screw hole
Made a few different sizes, 50mm 100mm 150mm 200mm Print laying flat. you'll see how the model it "notched". This is for strength. You'll want to add a few strips of hockey tape to that area to build it back up before regripping. slides…
I was struggle with stock sticks on pocket, so i found those, but i dont have long enough screw, so i remixed it for m3x12 screws which i have on hand. I hope this model will help you too :) Advice: Print with 100% infil, and 0.1 layer
Insert the bar end into the end of your bar. As you tighten the screw, the cones get closer together and spread the jaws apart. Additional parts required: 1x M4 Ruthex or similar 1x M4x35 Zylindrical Head Hex screw 1x m4 washer rubber…
Some U1 hoods do not fully seat onto the four flexible mounting points on the top of the printer. This adapter bridges the gap and allows the hood to fully seat to the printer. It is a two material print - the top is TPU so it goes up…
My kids have a Montessori table from Sprout Kids and the chairs are adjustable but the table requires replacement legs to adjust upwards. I created these extenders that slip on the end of the default 12" legs to raise it up to various…
Upgrader version of my older aux usb extender. Added 1 more USB port. Printed vertically by the width. Printed on: Ender 3 S1 | PLA+ | 0.2mm | 10% infill | Brim
Our robot vacuum kept bumping into our IKEA cabinet because it was too high for the Lidar to see and too low to drive under. That's why we decided to raise the cabinet two centimeters. the adjusting screw has to be removed from the leg…
All credits go to EastFreak for modelling the rack, sadly I was out of M5 threaded rod so I designed extenders to be printed. they can be bolted on with M4x8 screws, glue or just press fit them in. Print instructions Category: Animals…
Ikea Enclosure lack leg extenders They run between the original feet and the Lack legs, and will mean you need a longer screw. I created them due to finding out I needed more space AFTER printing all the other parts, I simply glued them…
I needed a table wide enough (600 mm / 60 cm) to fit my big printer, but the IKEA Lack tables are only 550 mm. So I improvised and made these simple extenders — and they worked great! 🔹 Print settings I used: 5 walls 5 top / 5 bottom…
I made a more permanent set of raised feet for the A1 Falcon so you don't have to keep removing the screw together ones that came with the rotary chuck .
If you are using 12-inch or larger wheels with Moza ES/ESX, you've probably noticed that standard paddle shifters are too short and it's hard to press them with the tips of fingers. This model extends them so that it's comfortable for you…
Multiple versions of extenders for GoPro
Our chairs were too short for the table so I created these to raise the chairs. Printed with PLA 0.20 using slicer Strength setting. You will need to scale depending on your chair leg size.
It is meant to be laser cut out of .2in wood but you can also 3D print the parts. This is still a prototype so please let me know if you experience any issues.
These are basic IKEA Lack table leg extenders. I needed to put the table over a computer and needed just over 2cm extra height, so I made 3cm leg extenders. They complain that they need supports. Don't do the supports. The legs are hollow…
When I installed 6.5mm hex extenders on my Typhon, the screw pins wouldn't fit the driveshaft so I had to use the standard pins. Since I was worried about the pins falling out, I made this sleeve that slides over the hex behind the tire…
This is a stackable 1x4 Gridfinity bin for 3/8" socket extenders that can accommodate either one 6" or two 3" extenders per slot. Printed in PLA with 10% infill.
I'm using some quick-load paper towel holders, but when I mounted them I had a quite large roll, turns out they are being sold in different sizes (never noticed before tbh). To enable some rolls that are too short for the current mounting…
Small inserts to extend the standard handlebars of your MTB. In the past I created two models that worked on two of my bikes. I created two models to extend the handlebars by 10 mm or 25 mm on each side and for handlebars with an internal…
Adapter to fit in 9mm hole and connect a baby gate with extension. Recommend using the included .3mf which orients the object horizontally.
This extender will raise the seat height of the IKEA Oddvar with 11cm. They are super solid, with thick 4mm walls and ribs. The base part has holes to use self-tapping screws to secure them to the insert part, but these are not necessary…
Designed for valances (curtain toppers) that attach using two notches to hook into a metal wall-mounted bracket. This extender pushes the valance 60mm further from the wall, allowing it to extend beyond the curtain-holding bracket of the…
Allows you to extend a variable tension rod by a few more inches! I bought a pack at goodwill for $1, but these 16" - 28" rods were too small for my 31" window. With these extenders, you can pop off the rubber ends, put these on, and add…
designed to be printed in flexible filament to hold the hex pencils firm but simple to use. one simple shape, short version, where you need two small pencils back to back to have enough length. one more complex shape that also can hold…
This is a stand for Miele Motif Dispenser with extenders (10mm and 20mm). I design this to make always the same quality prints on the coffe :) You can use it with cups with different height with the extenders. Print Settings Printer:…
I think this is the cheapest, easiest option for storing a huge amount of filament. 60 rolls easy. The rack isn't quite the right size to fit rolls correctly. This little extension makes it work.…
These base extenders are for 20x20mm and 25x25mm models to become 40x40mm, and for cavalry base models to become 50x50mm, for 4th edition Kings of War
Pool Fence Extenders and Spacer. I Came up with this design when shovelling dirt under my pool fence to meet the new regulations set out by my lovely Government. I thought there has to be an easier way. The regulations stated that the…
This is in order to accommodate the Prusa MMU 2.0 in the future. the Top corners replace the originals, the extenders are on top of the original bottom corners Category: 3D Printer Parts
LDARC X43 Custom Tire Extenders/Expanders - print in flexible material and add gripping material like anti slip mat, cut down to size. Adds a lot to ground clearance - see the comparison pic, the scales of the two photos is matched even…
This 3D-printed magazine extender increases the capacity of our OOD Original Tachi and Koda magazines. Pop off your base plates and very firmly press-fit on until you hear the one-way detent hooks click. This accessory continues the…
No idea how many types of calipers these will fit on, but it's worth a try? The calipers in the photo are anytime shock-proof calipers, but they also seem to fit well on some no-name metal and plastic calipers I've found. Each foot adds…
These are extenders for the "Stackable Battery Holders Improved" by KLXL. These extenders have ramps to avoid battery jams. I haven't added the tabs on the side as I'm planning to attach them to the wall but I've included the Fusion 360…
A simple and practical 3D-printed extension designed to increase the length of the pins that support and secure the rear window panel of the Jeep Renegade . These extenders are useful when the original pins are too short or when…
📝 Description These TPU foot extenders are designed as a clip-on upgrade for the original Voron 0.2 feet . They attach directly to the stock feet, increasing the contact area and significantly improving vibration damping and grip. Printed…
I bought the Buddy3D Tasting pack PLA, which comes with Buddy3D PLA Black (250g) Buddy3D PLA White (250g) Buddy3D PLA Blue (250g) Buddy3D PLA Lila (250g) Buddy3D PLA Red (250g) Buddy3D PLA Green (250g) Buddy3D PLA Yellow (250g) Buddy3D…
Adjustable hand grippers are a simple and efficient way to train grip strength, but most models have handles that are too small for comfortable use. Here’s a parametric set of handle extenders designed to significantly improve ergonomics,…
I do a lot of leather embossing with brass stamps, this is going to be a great help. My normal brass stamps are 9mm or 12.25mm in height. Print suggestions: 20% infill 3 perimeters 5 bottom layers Brute 2-T Hand Operated Clicker -…
Use colouring pencils, graphite pencils and crayons right down to the last few centimetres instead of throwing the stubs away: push the stub into the split collet and it grips. Three extenders, for standard pencils, thick pencils and…
I was struggle with stock sticks on pocket, so i found those, but i dont have long enough screw, so i remixed it for m3x12 screws which i have on hand. I hope this model will help you too :) Advice: Print with 100% infil, and 0.1 layer
This is a stackable 1x4 Gridfinity bin for 3/8" socket extenders that can accommodate either one 6" or two 3" extenders per slot. Printed in PLA with 10% infill.
Adjustable hand grippers are a simple and efficient way to train grip strength, but most models have handles that are too small for comfortable use. Here’s a parametric set of handle extenders designed to significantly improve ergonomics,…
📝 Description These TPU foot extenders are designed as a clip-on upgrade for the original Voron 0.2 feet . They attach directly to the stock feet, increasing the contact area and significantly improving vibration damping and grip. Printed…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
⭐ Love the GEN2 system? Support the project by joining the Jerrari Club or picking up a premium faceplate collection , it means a lot and helps fuel future designs. JERRARI3D.com The GEN2 Modular System is a 3D printable storage solution…
To install, Unscrew the mag base. Then screw the new one in (super simple). The extenders are somewhat untested, let me know if there are any issues.
![[unofficial] LowRider v4 DIY CNC - for use with Unistrut / Superstrut / metal strut - table extenders, rail clips, and rail placement jig v1.0](https://media.printables.com/media/prints/1178649/images/8868018_3e4f06c2-c883-4012-9e58-fbac3acf33a3_d3c9d2f1-d15d-488f-bb0a-152d6677cd7c/img_0275-with-labels-retouched.jpeg)
![Now for 32mm tubes - [unofficial] LowRider v4 DIY CNC - for use with Unistrut / Superstrut / metal strut - table extenders, rail clips, and rail placement jig v1.0](https://media.printables.com/media/prints/1216751/images/9130470_1760b9a1-f78a-4636-b5a1-a896a5953a1f_91313862-e5a6-4c8f-9f7d-795777348020/img_0275-with-labels-retouched-now-for-32mm.jpg)
