Counting matching models…
Vortex One (V1.0) Dual Gear Direct Drive Printhead for Ender 3 and 3 pro the Vortex One, a stylish, high-performance printhead designed for the Ender 3 series. Equipped with a dual gear direct drive extruder, it ensures precise filament…
Accidently mis-labeled by afterburner head, and had requests for a stealthburner. Untested as hotend is installed in my afterburner - but has ~1mm clearance requires the V6 collar to be fitted. Nozzle should sit ~3mm below airduct Voron…
After successfully releasing my 2-in-1 printhead and receiving many requests for a single-extruder version compatible with Trianglelab-mount hotends , I decided to design and share this upgraded printhead with you. This lightweight,…
This effector is designed for use of the E3D V6 hotend with M12 mount, and the DC42's IR bed leveling sensor. This can also be fitted with a 80mm Cob LED ring for light. Parts needed to complete this printhead: E3D V6 M12 hotend DC42 IR…
the Space have the right height for Triangle Labs CHC XL with and without extender. The correct distance for Carthographer is 2,6 - 3,0 mm The Distance with the Spacer is 2,8mm but changes with other nozzles.
StealthBurner phaestus Dragon printhead mod with more Airflow rather than pressurized but hotend.
Ich habe den oberen Deckel meines CoreOne + mit Magnetstreifen befestigt. Der Magnetstreifen ist 15x2 mm. Da deshalb der Druckkopf das Lüftergitter nicht mehr öffnen kann, habe ich diese Verlängerungskappe entworfen, die einfach auf den…
I made this model to replace the original printhead. The nozzle is located exactly in the same place as in the original printhead, so there is no loss of print area along any of the axes. The mounting of the original Z offset sensor is…
The mount has sufficient clearance where it connects to the chain, allowing it to move slightly, reducing stress on the wire during printing. Enjoy!
I recently upgraded my original CORE One to a CORE One+, mainly for the automatic vent opening/closing feature. In my experience, the vent would properly close but it would not open entirely, leaving about 1.5mm of possible travel…
This adapter does not need the difficult to install heat set inserts. It also removes material that can be used for cable clearance so I did away with the redundant mounting holes and added cable clearance and a pathway to snake the…
Modified Phaetus Dragon High Flow mount for Stealthburner v2.2 with Filametrix Mod . update on 8/5/2026 add FilamATrix Mod
I haven't seen many casings for this specific type of 3d printer. The cooling options have not satisfied me too. So I decided to make it myself The casing is printed flat, than you bend it with hairdryer. I highly recommend bending over a…
To produce dual color printing, use lerdge 2IN1 hotend, modify the upper opening and rear mating holes, and modify and adjust related mating parts. Can be made of PETG or stronger materials Enjoy printing!…
Der Druckkopf braucht folgende Voraussetzungen zur Montage. X-Achse auf Rail MGN9 umgebaut (frontseitig) Bondtech LGX Extrude, Revo Six Hotend, Makerpanda PCB ab C/D/E-Version The printhead requires the following prerequisites for…
Print it face to the buildplate with a support for the screw housing (as pictured) V1.1 Update: Noticed that i forgot the 2mm recess for the extruder. Added it to prevent it to touch the gear.
This is a mod for the FLSUN SR to mount the Phaetus Rapido HF Hotend on the Effector and use the parts of the original extruder to replace this thing with an Vz HextrudORT to create a good Direct Drive System for this machine. For this…
Features: M3 threaded Inserts (ADXL spacing 15mm) Improved the heatbreak duct curvature for better airflow. Improved heat-break fan fitment + fan alignment (new). Improved LED PCB clearance/fitment Reinforced mounting lugs Hex Key access…
BETA The printhead brackets supplied at Github allows for pressure fit around the neck. However there is a tiny bit of wiggle in this mount but the Aliexpress version also allows for removal of the neck to expose M2.5 bolt holes. These…
I needed the stealthburner to fit volcano size nozzle and filametrix.
This version is printed in one piece and includes a receiver at the top for a PTFE tube. Installation: 1. Attach the filament sensor to its original plate. 2. Fit the sensor with the plate into the mount by tilting the sensor so that it…
Install so the board is facing backwards.
I added a kind of ram to the fan shroud, to prevent smaller things getting stuck between the fan an heatbed when using continuous print. A longer M3 bolt is needed for the top mounting point of the fan.
I recently tested the Bambu Hotend on my VZ235 after hearing positive reviews about its performance. Since I primarily print technical parts that require high durability, strong layer adhesion is a key factor for me. Through my testing, I…
These parts tend to crack around the axle, so you only get half page prints, so here is a replacement part. I have no idea what the actual name of it is, so let me know if you know a better name than printhead pusher 😅 The dimensions are…
Vortex One (V1.0) Dual Gear Direct Drive Printhead for Ender 3 and 3 pro the Vortex One, a stylish, high-performance printhead designed for the Ender 3 series. Equipped with a dual gear direct drive extruder, it ensures precise filament…
The mounting bracket for my Neptune 4 Pro broke, so I modelled a new one to replace it. You will need 2 M3 heat inserts for this. I updated the model to be slightly thinner so as to not press on the heater plug as you can see in the…
A simple printhead case replacement for Anycubic Vyper. Main goal was to allow makers to “see” easily when the small strain gauge led is lit (to avoid print head crash into bed). Then I replaced stock air deflectors with wider ones that…
just do 100% infill only adds like 20 minutes and will be way stronger. this should help for setting up the BL Touch: https://github.com/knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S/wiki/Beginner's-Guide-(English ) should be offset with M851…
Upgraded my Cr-10s pro with Afterburner, remixed the a microswiss toolhead to suit this hot end. Nozzle position remains the same, has been printing very reliably since the upgrade.
Accidently mis-labeled by afterburner head, and had requests for a stealthburner. Untested as hotend is installed in my afterburner - but has ~1mm clearance requires the V6 collar to be fitted. Nozzle should sit ~3mm below airduct Voron…
I didn't want to solder the provided micro switches with the mellow kit, so I ordered DFW-05 micro switches from AliExpress. DFW-05 Type H: https://de.aliexpress.com/item/1005007440874580.html Attention: You may need to adjust the…
just for a bit of fun don't forget to share your pictures of the finished print
Here I designed a Bracket to affix the optional runout sensor to the Creality Ender 3 V3 SE Runout Sensor Printhead.
mount the TBG lite with 3 M3x8 screws printed in Extrudr ASA black
Stealthburner printhead for Fysetc Sailfish hotend
Simple clip to be inserted between the ribbon cable and its holding brackets. When the printhead moves to the side of the bed, the ribbon cable tends to slip out of their holding brackets. With this simple model it is kept in place.
MAKING THIS MOD IS AT YOUR OWN RISK, ANY DAMAGE DONE TO YOUR DEVICE IS YOUR RESPONSIBILITY Hardware requirements: 2x 40*10 24v Fans 4x m3*20 screws (no nut, they are resistance fitted) Soldering iron Heatshrink (recommended to prevent…
With this you can upgrade your Vyron Printhead with 5015 Fans for Part Cooling! Attention: you cant use the cover anymore!
For single extruder/ no AMS: Step 1: print the mustache using black filament Step 2: print the eyes (make sure to add a PAUSE AT LAYER 4 ) Step 3: change filament to white and resume printing Glue the parts to your extruder using double…
Installation: Detach the filament sensor from its original location. Fit the sensor into the mount by tilting the sensor so that it snaps into the top tab of the mount and press to fit the tube from the plate. Screw the plate onto the…
Step for https://www.printables.com/model/832598-vz-printhead-printed-version-for-blv-cube
I use TPU a lot, and this is difficult for the Artisan, because there is a gap between the feed mechanism and the hotend. This gap is visible on the cover photo on the second extruder: The white filament is visible in this gap. Flex…
Why this print head? Fits any 3D printer, that uses ender-3 ot similar hotend Printhead can be removed for service by unscrewing only 2 screws Easy to print - no supports needed Improved air flow for both hotend and model cooling BOM BMG…
With this you can add a cable chain / chainlink to your Vyron Printhead!
UPDATE: V3.8 added +3mm on Y. BL offset is X-32 Y0, Adjustable (On Y) X belt holder. new STL-s and STP. Printhead for KP3S with BMG/V6/BLTouch and X belt tension. You need: -LH BMG (Mirrored)! (When you have a RH version you can print the…
This is a remix of qidi_back_v4_3. I increased the diameter of the screw holes a bit as I couldn't get magnets to fit in the holes without taking a drill bit to them. I removed the layer between the magnets and the screws, and rounded the…
A printhead with nozzles for the Anycubic Viper, versions A to D using the original fans. I got a used Vyper with a broken printhead. The fusion-file from https://www.printables.com/model/105320-wide-deflectors-anycubic-vyper-printhead…
printed in abs at 90% for carriage, other parts can be printed in other material and with a lower infill, the part you need: 5 heat press 5 3mm screws 3 v-wheels (can be taken from previous printhead) 8mm inductive probe (bed leveling) 1…
Elegoo Centauri Carbon Printhead Fan Cover A bit loose but it can rotate when there is wind blowing from the layer fan <3
🔧 Custom K1 Printhead Housing with Adjustable BTT Eddy Mount The stock Creality K1 head is decent, but not always mod-friendly. So I designed a custom housing that: ✅ is easy to disassemble ✅ provides better access to fasteners ✅ allows…
I use my k1 with chc pro (so for unicorn you need to make it longer for 2mm) And also i don't use mcu on a head, so i am not sure that it will fit to the stock k1. prints without supports
I got tired of removing the two bottom screws every time I needed access the rear of the printhead, so I remixed the probe mount and a rear printhead cover so you can remove the rear cover separately, and the probe remains attached to the…
For those who are chasing less weight or just want to see the internal mechanisms
This is a custom direct drive (DD) setup for the Anycubic Kobra Go, designed to work with the stock ABL sensor. The original hotend has been replaced with a TZ E3 2.0, and the extruder is mounted using the HGX-LITE system. This…
But this is not compatible with the stock klick, you will need to put a spacer between the head and the klicky mount.
На фото модель с уклоном 80 и 70 градусов. Доработанная модель. Печатать с поддержками дерево, ПЕДГ. 2 периметра. Заполнение 10%.
EBP Reborn - Ender 3 / Sherpa Mini / Volcano printhead Original K3D EBP model by Sorkin has been significantly reworked to achieve following goals: more compact and lightweight design improved balance by moving motor to the back of X…
Kobra 3 Lightweight Printhead V2 For those who are chasing less weight or just want to see the internal mechanisms Difference from the first version Beam thickness increased Diagonals added
Front part of the lightweight print head For mounting, use special supports (2 pieces) Removed LED
A magnetic back cover for the printhead, that can be used with the original Printhead without further modification. To mount it, just put the original screws back in and add 6x3mm magnets at the appropriate layer. The probe gets mounted…
I made one like this awhile ago, but it was getting kind of old so I thought I would update it. Has a color change so that you only have to glue it to the printer when it is done. Printing Settings: Resolution : 0.2 Support: NO Infill :…
I adapted the Elegoo Centauri Carbon Printhead Fan cover (credit: magedark) to utilize the High-Efficiency fan grille STL developed by Noctua (credit: Noctua_at). I'm not sure about any actual efficiency gains from this fan, but according…
This was designed in conjunction with a duender build with the challenge of not using any other parts than the parts that came with 2 ender 3s bought on fb marketplace The printhead was made with the same overall height as an assembled…
Fan cover for printhead pla+ first layer height 0.2 layer height 0.2 first layer speed at 30mm/s first layer acceleration 300mm/s
This a box for distribution board (PCB) of the " Direct Drive Upgrade Kit " for the TronXY X5SA Pro printer.**** I needed this because the gantry holder/gantry plate of the upgrade kit, which holds this PCB originally, cannot be used with…
The Core One Printhead Left Cover with cutouts for access to the heater and thermistor connectors. There is a compromise I made between the ease of removing the connections, printability, and still functioning as protection of the rest of…
After successfully releasing my 2-in-1 printhead and receiving many requests for a single-extruder version compatible with Trianglelab-mount hotends , I decided to design and share this upgraded printhead with you. This lightweight,…
This is a remix of this fantastic model for Elegoo Centauri Carbon with 10mm round magnets , which I had on hand. Another some minor modifications for a better fit. This model provide open air ducts for best hotend cooling and hole for…
Ender 3 V3 SE/KE Filament Sensor Mount on printhead (PTFE Tube)
I noticed that my printers sometimes would home inconsistently. I own two core ones that I build from the conversion kit, thus i did the extruder wiring myself. For me, the wiring undernath the cover pushes into the cover, slightly moving…
This replaces the right printhead cover, and has mounting holes for a generic ADXL345 accelerometer. M3 brass threaded inserts are recommended for the mounting holes. I have not yet tested the accelerometer but it should be wired up as in…
Spacer to align eddy on original screw for stock inductive sensor. Use with skinny eddy. Use with any version of BTT EDDY with EDDY-NG. Spacing from bed is just right :-). You can use with stock THR via USB, unfortunatly my THR fall apart…
Передняя часть каретки для печатающей головки Qidi Q1 PRO. Т.к. имеется болячка с вырыванием микропробы, пришлось смоделировать эту часть опираясь на модель предоставленную QIDI TECH. Модель оптимизированна для 3д печати, поэтому я думаю…
inspired by Svennixx's model but redesigned from scratch to put the nitehawk board up and to the left centering it on the toolhead rather than the motor. This is necessary because the heater terminals on the nitehawk interfere with the…
This is a multi-part printhead cover for the Qidi X-Plus 3. It has been remodeled to use multiple pieces assembled with M2 screws. It is based on the newest cover Qidi released, with the side fan and custom blower. All parts have a nearly…
hey folks, Update: so the fan duct is ready, it fits on an 50mm radial fan designed for that…
I liked the fan fittings on the PapaSchlumpf design, but the front fan is still the loudest fan on the printer. I remixed it a couple times to tilt the fan out more. The stock LED on the head is super dim, so I removed the mount and added…
These jigs are for the repair of both the print head and feed assembly side of the feed tube. While this was primarily designed to help owners of my open source kit replace damaged/worn tubes, it may be useful for Cube3 owners using other…
This strain relief was originally made to solve a fire hazard, namely the USB-C cable on the print head, during a print the cable moved a lot and could break free from it's housing causing the cables inside to become damaged and possibly…
v2.1 -Smoother transition for air flow to heatsink v2.2 -Smoother transition for air flow to heatsink -Parts air cooling direction is more under nozzle Print settings: Material: ASA/ABS Layer Height: 0,2 mm Infill: 40% Wall Count: 4 Solid…
Update 2025-11-24 - This model is tested and working but if you are using dtang's cover this implementation is WAY cooler I think. https://www.printables.com/model/1488590-combined-magnetic-top-cover-handle-with-core-one-v Update…
Описание на русском ниже: This printhead based on project of Kirill Plasma https://www.printables.com/model/922675-impact-printhead-for-ender-3-tevo-tornado-lomacho Target of project: I wanted to avoid of need very accurate print of…
With all the great light weight printhead covers available, there is a temptation to operate the printer without the rear cover. Doing this risks the capacitor and heatsink on the PCB banging into one or other of the stepper motors at the…
This model is a custom Archetype printhead mount adapted for Parallax gantry belt routing and designed to clamp the belts directly on an MGN9 carriage . The mount allows the use of the full Archetype toolhead ecosystem . Extra BOM 4× M3…
Remix of the original model that makes it compatible with the kobra 3 V2 variant.
Hi! Here I share the assembly of a print head based on A4T with Cartographer and ProtoXtruder, but the parts, except for the feeder, have some differences from the original. The assembly uses a heavily upgraded carriage from Mantis. The…
I wanted to use the Vzbot Printhead and I had a Eddy Probe already with me so I created a holder for the printhead. There are two versions one very close to the fan (which is the one I'm using) since the fan 3010 is just attached to the…
I wanted to be able to take out the extruder without having to disassemble the whole printhead and I couldn't see a LGX extruder adapter plate (probably because you can screw it directly on the top plate). However, if you don't use the…
Made a small change of SB2209 anchor for clockwork2. During my assmbly I couldn't find an anchor component that fits both spring steel and an umblical. So I simply combined two I found on the website. One from the official clockwork2 stl,…
This effector is designed for use of the E3D V6 hotend with M12 mount, and the DC42's IR bed leveling sensor. This can also be fitted with a 80mm Cob LED ring for light. Parts needed to complete this printhead: E3D V6 M12 hotend DC42 IR…
the Space have the right height for Triangle Labs CHC XL with and without extender. The correct distance for Carthographer is 2,6 - 3,0 mm The Distance with the Spacer is 2,8mm but changes with other nozzles.
StealthBurner phaestus Dragon printhead mod with more Airflow rather than pressurized but hotend.
