Counting matching models…
Since I could not find the ideal temp tower that meets my expectations, I designed my own. Features: - Uses little material because it is not too big - Different overhangs, 45° and a curved one - A thin wall at the overhang to test the…
This simple tool helps find the proper offset for your Cartographer probe in relation to your nozzle tip. Having a 2.6-3mm Z offset is critical for reliable operation of Cartographer Touch (nozzle probling). The Y offset ruler is just a…
Features: - Uses little material because it is not too big - Different overhangs, 45° and a curved one - A thin wall at the overhang to test the layer adhesion by breaking it - A bridge, from 30mm length in the back to 35mm in the front -…
This enclosure was built to house the ESP32 and sensor that measures humidity, temperature, pressure, among other things for use in HomeAssistant. You can print in PLA as it is used in room temperature indoor conditions. This is designed…
Tethered caps for sharp needle type multimeter probes. Print Settings Printer: Artillery Sidewinder X1 Rafts: No Supports: No Resolution: 0.12mm Infill: 100% Filament: Any TPU Any Category: Electronics
Test probe shield for the FNIRSI 2C53T DMM test leads. The probe it is very long and sharp, but if you are probing near other terminals, this cover will reduce the risk of shorting to something nearby. I used tree supports for the inside.
V3.0 is the latest version and more compact due to the 90 degree turn i did with the probe
Print on PETG tap the hole with a M5 Tap so you can use the go-pro screw
2/15/26 - UPDATE: Added an adapter to go from Creality CR-Touch to BTT MicroProbe, based off of user feedback (untested by myself). This is an adapter to mount a BTT MicroProbe in place of a BLTouch V3.1 (might also work to replace a…
Part cooling duct for biqu h2 and biqu microprobe mount. Need 2x m3x3x3.5 heat set inserts for fixing the 5015 fan and 2x m3x3x3.5 heat set inserts for fixing the probe. Added v2 for less supports when printing. Apply some glue to…
Adapter for input shaper probe https://www.printables.com/model/422330-clip-on-rp2040-zero-adxl-345-input-shaper-probe
Designed to hold 12.5mm diameter probe on 6mm glass. Original printed from PLA, but i suggest using PETG or something else a bit more flexible than PLA.
I designed this calibration probe to use the leftover 4mm dowels and bushings from a StealthChanger build. It's also built around the hartk1213 sexbolt Z endstop PCB. It works similarly to the sexball probe that is commonly used for…
This custom-designed probe holder is made specifically for my Rigol DHO804 oscilloscope. It should work with any DHO800 series scope and possibly DHO900 series (need to verify). It provides a secure and convenient storage solution for…
This is a holder for the two probes for the Rigol Desk Multimeter DM3058 and others. I printed it in white PETG and laying on the side with support (for the clips)
Requires two hot melt inserts. I placed the wiring on the outside so that it is easy to reach and has a smaller x-offset for the probe. I printed mine with ASA at 100% infill.
YouTube demo video: https://youtu.be/58Jl6n0qayw YouTube build video: https://youtu.be/NGpEOg99Y-0 A radio controlled version of the 'Prober' vehicle from the 'Jonny Quest' show. The episode is S1E18 called 'Pirates from Below'. It's a…
The original one was a bit short. Remixed it to make it have a bit of extra wiggle room. Cover images taken on iPhone 14 Made in Fusion 360
I needed an easy way to store and pull the ZProbe for my XCarve. This is 2x4 size grid. It has filleted corners and finger pulls. I did this in PLA but PETG should be fine as well.
Wall Cradle Bracket for Sonoff 02LD Temperature Sensor & Probe. I recently purchase the SONOFF SNZB-02LD IP65 Zigbee LCD Smart Thermometer (Probe Version). With the probe attached to the boiler flow pipe the temperatures can be monitored…
Ce conduit de refroidissement personnalisé améliore le flux d’air autour de la buse pour la Comgrow T500 équipée de l’extrudeur Biqu H2 V2S . 👉 Le support intègre un positionnement optimisé pour le probe de nivellement automatique (type…
Mount for the E3D PZ Probe PCB for use with Stealthburner with a Cartographer3D CNC carriage. It can also be used with a printed carriage that you can get from Gusk's model . This model has a shallower angle for the PCB than the original…
Multimeter probe holder for easy one-handed changing. Two probe sizes with a diameter of 10 mm and 8 mm. держатель щупов мультиметра для удобного изменения одной рукой. Два размера щупов диаметром 10 мм и 8 мм.
This is a modified version of the hook-on dragonburner cowl with screw holes on the side and a mounting piece, which allows operation of the Cartographer probe (or similar). It was designed for my toolchanger but should also work well as…
These are realistic models of ultrasound probes commonly used in the emergency department for bedside ultrasound. They’re an excellent way for students to become familiar with probe handling before using the real (and expensive)…
In my continuing quest to bring the most obscure props of Star Trek (original series,) I have done my best to recreate what the “Star Trek Technical Manual” (1975) identified as a Ray Gun. In the TV show, it's never used as a ray gun. In…
A box for the high voltage probe. The key feature is the cutaway at the bottom. These probes have cables coming out of both ends, which makes it not a good fit for a standard box. Updated design which has holsters for probes, oscilloscope…
This enclosure was built to house the ESP32 and sensor that measures humidity, temperature, pressure, among other things for use in HomeAssistant. You can print in PLA as it is used in room temperature indoor conditions. This is designed…
New nozzle to probe Y offset is now 21.65mm instead of 22mm.
A relatively simple addition of an eddy probe to the front cover of SB. Allows for it to be easily added to a tap setup with a small (Y-25mm) offset. In my case it can scan the whole bed in my BLV meets trident mashup. This model was…
Bracket designed to allow for mounting of 5015 fan and 8mm inductive probe to NF-Wind (or clone of thereof) extruder. Mounting height is optimised for use with TriangleLab CHC Pro. 5015 fan to be mounted via 3mm screws with heat-set…
I was wanting to have a good place to store my Amprobe AM-510 multimeter. None of the premade Rugged Box Parametric files fit. So this is my first attempt using Fusion360. Credit to another box comment for the pocket having no walls (top…
Overview Kataan Probe – Star Trek: The Next Generation This is a detailed, multi-part replica of the Kataan Probe from Star Trek: The Next Generation, inspired by one of the most emotionally powerful episodes in the entire franchise. The…
This is a print in place magnetic field probe. Use this to view 3d fields around magnets. A 50mm by 10mm by 11mm magnet fits inside the holder, although some might be loose. To make the probe work with weaker magnets, I found taping two…
Mounting solution for a BTT Eddy probe on the Ender 3 S1 and similar Sprite extruder models. Only tested on Ender 3 S1 Suggest ABS or similar heat resistant material. Support will be required for the alignment guide. I printed my original…
The magnets are in slightly different positions in the DB zeroclick cowl compared to the ZeroClick probes magnet position. (This might be because of the ZC probe versions are not followed through on the DB github.) I was afraid it will…
Test probe shield for the FNIRSI 2C53T DMM test leads. The probe it is very long and sharp, but if you are probing near other terminals, this cover will reduce the risk of shorting to something nearby. I used tree supports for the inside.
These parts attach to a RepRapMicron Axis Driver to turn it into a Z Axis with a print head. The print head allows deposition of UV resin in 10μm or finer droplets, or subtractive fabrication and manipulation with a stouter probe tip,…
A box for fluke accessories. It is wall mounted because it holds a lot of weight when fully loaded. Screw size is #8, which is what comes with wall anchors from home depot. One side holds two boxes of fuses. The other side holds two…
Also need a D = 5mm transparent pin for light transmission
I'm setting up a new cnc mill, and after organizing my machining drawer I needed a safe and secure way of storing my WP-500 touch probe, needing to use a 2x2 grid I had space to add in two ER16 nut holders (slightly different types, one…
A remix of the Klicky Probe mount for the Voron 2.4 to adapt it for use with the Duender Medusa HC by Sergei Irbis.
V3.0 is the latest version and more compact due to the 90 degree turn i did with the probe
Variation of "dock mount variable part 2". The part is 5.5mm shorter.
I recently built a Vzbot gantry on an Ender6. For the hotend I had a V6 style hotend and an Eddy BTT. I initially created a holder just for the BTT but then I realised that it would rattle when using the printer as normally the V6 Fan is…
Design for mounting the DSO-TC3 mini oscilloscope and probe on 2020 extrusion
Set up the following way (back to front): 1 mm insert for thin PCB (Nooelec UWB antenna) 6x square holes for cheap Ali/Amazon probes 2 mm insert for normal thickness PCB (1.54 mm): H-Tool SL-10 mini LogPer antenne 2x mount for VHF and UHF…
No more poking sharp probes into your hands, while searching in your tool bag! This part is a variable probe holder for your multi meter, that tidies up your multi meter and probe mess. Flexible Probe Holder for your Multi Meter Storing…
These probe holders are deisgned to hold oscilloscope probes in place for debugging and testing. Use with 1/4oz adhesive wheel weights to help keep them stable along with 9mm OD rubber bumpers. The source design files for SOLIDWORKS and…
I was looking to upgrade my Voron LDO Rev D Trident with an A4T toolhead, Xol carriage, and Beacon probe. I did not want to go sensorless for the X/Y as the switches have been reliable so far, but quickly discovered the new…
replaces the stock screw on cone cap for the probe that fits newer 2.0Ghz seizure-less taps. prevents damage to the pin, reduces contact with water and dirt, and provides easier storage of, and access to, the probe. can mount to meter bag…
fits the smaller SA style AOI probe. keeps the probe from getting wet, dirty, and generally banged around. also helps with managing meter jumpers. mount the holder to your meter bag with a zip tie print with a few extra walls (3-4) and…
fits the KS plunge probe for older RF taps, 1.2Ghz and lower. Better than the old shotgun-shell style cap they come with. prevents damage to pin, reduces water and dirt. holder attaches to meter bag with a zip tie at 90degree…
I designed these to work with my Craftsman multimeter probes, they may or may not work for yours. The probes snap in so that they will not fall out. Printed without supports using 95A TPU. Do not print with PLA or any filament that is not…
A simple locking PicoPi case for making the Pico programmer and Debug device PicoProbe, The Raspberry Pi Debug Probe is a USB device that provides both a UART serial port and a standard Arm Serial Wire Debug (SWD) interface.
A swingarm dock and toolhead mount for the Medusa HC and/or Duender. May work on other printers as well. BOM:
I saw a similar sort of thing on the internet, so I thought I'd make my own design. It's a holder for two probes so they can be held in one hand leaving the other hand free to manipulate the item being tested. I've added two more holders…
I don't like how sensorless homing is just a semi-controlled crashing of my printhead, so i wanted to keep my physical x and y endstops on my trident. Heres a quick remix of the klicky probe module to add an extension off the side to…
I greatly appreciate the work that stew675 did to create a Beacon mount and code for the Plus 4 printer. I found that the mount was compciated to install and blocked the front view to the nozzle. Swapping nozzles and removing the little…
Just a small adapter to put a ADXL345 accelerometer with a 14.5mm mounting pitch onto an M12 sized bed level probe. Screw the ADXL to the adapter with a pair of short M3 screws, then put the adapter on the end of the probe and secure…
I needed a place to put probe that works with multiboard but din't exist so made my own
This is a universal probe holder for the RIGOL PVP3150 passive probes that come with the DHO800 / DHO900 series oscilloscopes. The probes are held securely in place with a satisfying snap. Other probes with a diameter of around 10.5 mm…
This is a holder for the FNIRSI DMC-100 digital multimeter, including a convenient way to attach its probes. The probe attachment piece snaps satisfyingly onto both the multimeter and the two probes. Behind the multimeter, there is a bit…
hey guys this is the 3 point probe that i made what you need will be 3 x 3mm pins (i use used 3mm drill bit to make that) 3 x 3mm bearing balls, this is for over travel alarm sensor 3 x 6mm bearing balls, for the raw stock touch probe 1x…
I love the petsfang fanduct, and I recently got the Biqu Microprobe, but there are a few minor issues with the petsfang probe mount. The probe mount is quite far away from the nozzle, so it won't be as accurate, and making the fanduct…
I wanted a tish more adjustment up/down on the Eddy probe mount, to match the recommended offset by BTT with the nozzle. The model assumes one would use the stock hotend I assume. (I have a phateus.) I added slots to the back of the mount…
A remix of Darksideee's dental probe holder. No support required. A full size HSW insert was added, one is plenty for a light load. Thanks to Darksideee and RostaP for the original designs.
A little holder for four dental probes or similar objects to fit the openGrid system. Thanks to Darksideee for the original design. Thanks to DavidD for the openGrid system.
Is it a bull? Or a mouse? A mousebull? A holster/sheath/scabbard/holder for a Thermapen TX-1002X-NP Pro-Series Waterproof Needle Probe. Fusion360 design file included - feel free to remix!
Holder for attaching the probe to the place for the electric heating element.
Wall mount suitable for 3D probes with 6mm shaft and side entry USB-C connector Screw holes are for 4mm screws (no. 8)
I made something like a lightweight case and holder for multimeter probes and cables, for easy carrying. All the parts are glued together after printing.
Extruder ribbon cable strain relief cable guide Fitting a cable guide to your printer allows the ribbon cable to flex gently over its length rather than bending all in one place - which can lead to broken wires. This unfortunately is a…
I've included a STEP file of the whole assembly for your reference For more info go to Smart Orbiter V3 Extruder: https://www.orbiterprojects.com/so3/ Euclid Probe: https://euclidprobe.github.io/ Cheers and happy printing! __Yves
I just measured the original bracket. "Zprobe Ender3V3SE.stl" should be a perfect fit replacement. 5mm shorter should account for normal height heat blocks which I needed to make ~~2mm longer should account for volcano nozzles / heat…
This design is a variation of my spring loaded clip probe adapted for banana (4mm) connectors: https://www.printables.com/model/664568-electrical-clip-probe-spring-loaded It uses a piece of wire (0. to 1mm diameter) a M3 8mm screw and a…
Zugproben angelehnt an DIN EN ISO 527-2 von 2012. Die Probengeometrie ist nach Norm für Spritzgussproben modelliert, die Dicke der Proben wurde von 4mm auf 9mm erhöht um den Einfluss des Infills besser testen zu können. Wichtig ist die…
What is this? Adapter (v5) for mounting in a standard place under the Lidar - table card removal probe from BTT BIQU MicroProbe v1/2. What is needed? 1. Auto-level sensor BIQU MicroProbe v2. ( https://sl.aliexpress.ru/p?key=k0b2Of8 ) 2.…
I installed this cheap chinese sensor in my swiming pool: pH-W18 Yieryi-Tuya Smart WiFi, PH ORP, TDS, EC SALT S My pool water circuit is in 5cm diameter. I used a support collar (see picture) with a ¾ inch thread. Then I printed the probe…
Concept This holder clips on to a standard 40mm specimen sample pot and keeps a fine wire in suspension. The wire itself (typically 0.3mm to 0.8mm diameter, usually 0.3mm 316L stainless steel) is held in place by a croc clip on the tab…
Made to work with King Uni-t Shroud. Will need 24mm long M2 or M2.5 Bolts. Link below for the shroud. https://www.printables.com/model/288580-king-uni-t-shroud-universal-hotend-shroud
This is a replacement part that is easy to print to replace the housing for the sv06+ inductive probe for ABL.
slight remix of the X4 micro probe cover. adding a little strength to the area of the micro probe. Follow the instuctions in the original post.
****************** UPDATE: I have published a redesign of this model at https://www.printables.com/model/985777-biqu-microprobe-mount-for-sovol-sv08 The redesign is far sturdier, and there are three versions for different length nozzles -…
Mount for Euclid for the Ratrig toolhead beta 2. To fit this, you also need a new front piece for the toolhead, i.e. one that does not have the Pinda mounting tube. The new front piece is included. I made this to make the head lighter,…
For some reason I couldn't find this already out so I made this simple adapter to mount the bigtreetech eddy or an inductive probe to a XOL hotend. One mount is for if you don't have endstops and the other mount is for the regular…
I modified the original version to allow a bit more space to work with Nadir's CN3D shrouds. To work with the M12 probe. Print in ABS. It will use the same hardware as the original design.
My multimeter (UNI-T UT61E) probes hang loose and can get untidy. The probes dangle and can get caught and break. To help reduce this dangle problem (but not eliminate), I came up with this design to allow the attached probes to be…
Hi I created the container for the logic probe when our electronics club was building the logic probe with the CD4001 IC and I did not want to use a pipe for a container. Circuit comes from…
This is an enclosure for the "RF active probe 0.1-1500 MHz bandwith SMA output" by 60dBM.com ( https://www.60dbm.com/product/rf-active-probe-0-1-1500-mhz-bandwith-sma-output/ ). It needs a couple of other parts: Two M2.5x8mm button head…
This is an enclosure for the knockoff RIGOL logic analyzer sold on eBay: https://www.ebay.com/itm/224648789536 There are 2 parts - after printing they are to be glued together. I printed them with PLA and glued them with Krazy Glue…
Sometimes, when using an oscilloscope, it is desirable to be able to get the probe attached to the PCB. This may be to lower the loop inductance of the ground lead or just because the probe is difficult to hold in place. This adapter…
This is a simple CNC Z-Probe holder. It fits a generic probe size. It attaches anywhere on a 20x20 or 20x40 aluminum frame using a M5x8 screw and and approprate T-nut. I printed this in PLA at 0.16 layer height and 50% fill. Pictures show…
Dummy model of this part: https://www.ossila.com/products/four-point-probe-head?variant=44570049937624 I made it for work to help design fixtures to attach the probe head on our own equipment.
I designed this tray to nicely store my Hameg Oscilloscope Probes. It will likely work with many makes of probes or you can modify it with the included fusion 360 file. It is stackable. You can experiment with different printer settings…
