2,924 models
The charging cable always breaks at the same position, just right under the plug. Don't replace it, Repair it with this easy print! This works for Apple USBC and lightning, as well as for samsung charging cables! No glue or tape is…
Print approx. €0.04–€0.05 excl. taxPreliminary estimate for one variant
You can put them on the handlebars in the normal position and turn the bicycle afterwards. They are designed for the handlebar with a diameter of 23 mm . I printed them with 4 perimeters, 15% honeycomb infill, without top and bottom…
Print approx. €5.27–€6.44 excl. taxPreliminary estimate for PETGSource material: PET
Ethernet cable fix which prints WITHOUT SUPPORTS. The layer line orientation aids in keeping the cable in the port. Print settings: layer height 0.2mm 3 thick walls Infill: Does not matter since the piece is too small to even have infill…
Print approx. €0.11–€0.14 excl. taxPreliminary estimate for one variant
This is a repair clip for your broken Ethernetcable. You can easy print it. The clip makes it possible that the cable does not always slip out so easily when the clip is broken off at the top. To print: you can use PLA too Use supports
Print approx. €0.25–€0.31 excl. taxPreliminary estimate for PETGSource material: PET
A little support is needed but comes off quite easy
Print approx. €2.93–€3.58 excl. taxPreliminary estimate for PETGSource material: PET
Easily 3D Printed tool that is used to remove adhesive between two parts that have tight tolerances between them and are fragile. Most commonly used when removing touch screen from an phone or tablet. IF YOU HAVE A RESIN 3D PRINTER I…
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for PETGSource material: PET
All-in-one Repair Kit for a Broken Flush Mechanism. Straight and Angled Levers included. American Standard. No Supports! Higher Infill on Lever Arm Recommended. Assembly Order: Bolt (Cut-out towards the Chain) Nut (Counterclockwise…
Print approx. €1.92–€2.35 excl. taxPreliminary estimate for one variant
What is it? Printed part to connect the particleboard floor of a drawer to its chipboard backpanel. Tested with a repair and enhancement on my 2012 IKEA MALM chest's drawers. Might work for others with the same design too. Why use it?…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for PETGSource material: PET
Zip-Tie Garden Hose Coupler | 16mm Water Line Connector This simple yet effective 3D printed connector lets you quickly join two 16mm diameter garden hoses without specialized tools or fittings. Perfect for extending your watering reach…
Print approx. €0.24–€0.29 excl. taxPreliminary estimate for PETGSource material: PET
An ethernet RJ45 repair clip with a working snap lock that locks the plug in the socket. Prints without supports added from the slicer thus it prints quicker and and uses less material. NOTE: Needs to be printed with 3 perimeters (3…
Print approx. €0.11–€0.13 excl. taxPreliminary estimate for one variant
Modification of the model by Plutho to accommodate two instead of three AA batteries. This model may need to be customized as needed.
Print approx. €1.81–€2.21 excl. taxPreliminary estimate for PETGSource material: PET
This is a large, useful toolbox for small tools and parts. I use it for repairing my 3D printers because of all the small parts and tools needed. I have several printers that are used a lot. Anyone that really puts their printer to good…
Print approx. €4.37–€5.34 excl. taxPreliminary estimate for one variant
While you are staying safe at home, you might have something break that you'd typically go buy a replacement or perhaps a repair bracket for. (For example, the snack drawer's increased contents and enthusiastic children might result in…
Print approx. €0.44–€0.54 excl. taxPreliminary estimate for PETGSource material: PET
An RFID chip repair case is a practical accessory designed to address common issues with RFID chips. When a new RFID chip is inexpensive but new one may encounter registration problems, this case offers an alternative. If the side cover…
Print approx. €0.49–€0.60 excl. taxPreliminary estimate for one variant
Creating a spacer for an M3 screw Spacer for large screw hole Easy and fast printing Printing: Material: PETG Supports: no Orientation: can be printed from both sides
Print approx. €0.04–€0.04 excl. taxPreliminary estimate for PETGSource material: PET
War of the Ring Army Token Repacement. Orginal tokens are boring and easy to overlook.
Print approx. €1.95–€2.39 excl. taxPreliminary estimate for one variant
Description: A buckle designed for easy replacement of a broken one without the need to unstitch your bag. Simple to print and assemble. Recommended materials: ASA or PETG. Supports are required – organic supports were used. Fits: 19mm…
Print approx. €1.40–€1.71 excl. taxPreliminary estimate for one variant
You can use these clamps when repairing for instance an iPad screen and you need to clamp the edges while the glue sets. I recommend using automatic support painting on the C part of the clamp and using organic supports. When printing in…
Print approx. €2.16–€2.64 excl. taxPreliminary estimate for one variant
I searched for a repair solution to the problem of kitchen cabinet door hinges being pulled off breaking the screw holes in the cabinet. I tried a couple of solutions but really they were not effective. I found that the hinge wasn't…
Print approx. €1.78–€2.18 excl. taxPreliminary estimate for one variant
This remix is for the standard handle bar diameter size of 22,2 mm. Perfect for working on your bike without scratching your handle bar or your bell. Makes it more stable as well. Print settings: Material: PETG, PLA might be too brittle…
Print approx. €3.37–€4.12 excl. taxPreliminary estimate for PETGSource material: PET
A simple way to organize your screws or parts while repairing.
Print approx. €0.60–€0.74 excl. taxPreliminary estimate for one variant
Quick fix for some 4 colors pens. It's mounted in force. I didn't make any thread. Some glue might be needed. Printed in PLA, 200 µ height.
Print approx. €0.37–€0.46 excl. taxPreliminary estimate for one variant
The mounts are designed for handlebars + handlebar tape with a diameter of 40mm and increased ground clearance. I printed whit PETG them with 4 perimeters, 10% honeycomb infill, without top and bottom layers.
Print approx. €2.36–€2.88 excl. taxPreliminary estimate for PETGSource material: PET
I had to repair our Kitchenaid mixer during lockdown with no access to a parts supplier. This little gear did the trick. The OEM part is nylon and designed to fail if overstressed, thereby saving the rest of the gear train. It's an easy…
Print approx. €0.97–€1.18 excl. taxPreliminary estimate for one variant
Print two identical shells (there are four different lengths available) to repair your lightning connector. Before put both parts together use some silicone to fill this inside the two parts. Afterwards put your connector with both parts…
Print approx. €0.13–€0.15 excl. taxPreliminary estimate for PETGSource material: PET
Se imprimen tres partes por separado: base, asa o manija y tapa. Luego de imprimirlas se debe pegar el asa o manija con la tapa. NO requiere soportes. Fácil para limpieza después de su uso.
Print approx. €1.90–€2.33 excl. taxPreliminary estimate for one variant
Better looking
Print approx. €1.21–€1.47 excl. taxPreliminary estimate for PETGSource material: PET
REPAIRED correct files loaded scaleable and easy to print
Print approx. €9.27–€11.32 excl. taxPreliminary estimate for one variant
A repair "kit" for USB-C plug casing. Depending on how much of the casing is missing, print “USB-C_cable_plug_repair_additional”. If only one side broke of then you can skip “USB-C_cable_plug_repair_additional”. Please also note the…
Print approx. €0.31–€0.38 excl. taxPreliminary estimate for PETGSource material: PET
Holden VY / VZ Centre Console Flip Lid repair TAB, This will also suit some US & exported models. Printed in ABS, 50% Honeycomb Infill, 0.15mm Layer height, Print 3 or 4 at once. Brim can be used if you have adhesion issues, These have…
Print approx. €0.41–€0.50 excl. taxPreliminary estimate for one variant
I created this model to remove the arm from a Ikea FRIDANS roller blind but the model may also be used to replace broken parts of common roller blinds. The mechanism is working quite well, if you are having issues please write a comment…
Print approx. €5.02–€6.14 excl. taxPreliminary estimate for PETGSource material: PET
Needed to fix my patio umbrella. Two of the arms broke after the wind knocked it over. Just needed to use some M5x35mm bolts with some washers and nuts. I used some nylon washers since it's supposed to be able to to articulate when…
Print approx. €1.77–€2.17 excl. taxPreliminary estimate for PETGSource material: PET
My Print Parameters: Resolution: 0.2 Nozzle: 0.4 Seam position: Aligned Infill: 15% Top Layers: 6 Bottom Layers: 5 Perimeters: 2 Rafts: No Supports: No Material: PETG Prusament Signal White/Lipstick Red, Urban Grey Happy printing!
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for PETGSource material: PET
Weight plates for blinds sometimes become brittle and break when removed from the connecting chain. Several popular repair solutions ( https://www.printables.com/model/147266-89-mm-lysel-slatted-curtainvertical-blinds-weight ) suggest…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for PETGSource material: PET
Small parts tray for Feedback Sports Pro-Elite bike repair stand As I have enough storage space / room in the workshop (workbench etc.), I didn't need a large tray for the assembly stand. The holder is sufficient for valve caps, disc…
Print approx. €7.91–€9.66 excl. taxPreliminary estimate for PETGSource material: PET
Anakin Skywalker Model cut and prepare for print 3D and gluing
Print approx. €1.45–€1.78 excl. taxPreliminary estimate for one variant
Clip to replace a broken one on your dryer horse with 15mm inner diameter rods. Print two halved pieces that join when forced into the rod. No supports needed due to half cut design.
Print approx. €0.51–€0.63 excl. taxPreliminary estimate for PETGSource material: PET
This is a repair for a Ford Transit headlight housing. Housing arrived with a broken tab and instead of returning, crafted a repair. This was on an upgraded Ford headlight (projector beam) on a Storyteller Camper Van. Printed in ABS and…
Print approx. €0.50–€0.61 excl. taxPreliminary estimate for one variant
The handle of a pool skimmer basket is broken. It breaks at the end that fits into the basket. The plastic must be poorly resistant to the aggression of salt-treated water over time. The handle is rigid and it is by distorting the basket…
Print approx. €0.57–€0.70 excl. taxPreliminary estimate for PETGSource material: PET
With this thing you can rapair your broken protective rubber sleeve on the Beyerdynamic MMX 300 headset cable. You have to print the part twice. To open the earpiece you hav to do a few easy steps. Remove the earpiece cushion, than you…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for one variant
Roof/Railing Patch -Repair _____________________________________________________________________________________________ This Customizable patch can repair your broken corrugated roof or railing. You can set your own dimensions with FCStd…
Print approx. €3.10–€3.79 excl. taxPreliminary estimate for PETGSource material: PET
I had only used my Igloo Portable Ice Maker for a little less than a year before it gave out. I came home one day and it had just stopped working. I searched the ‘net for answers, and finding few, decided to just tear the machine down and…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for PETGSource material: PET
We have a few Tommy Bahama Beach chairs and after many years the plastic part that connects the chair frame and allow for the chair to fold broke at the main junction. The challenge was to create an ASA 3D printable part that can take the…
Print approx. €6.36–€7.78 excl. taxPreliminary estimate for one variant
This part is for this particular water bottle that is sold online and in stores in North America: “Zak Designs Minecraft 18/8 Single Wall Stainless Steel Kids Water Bottle with Flip-up Straw Spout” No doubt, there is probably…
Print approx. €0.25–€0.30 excl. taxPreliminary estimate for PETGSource material: PET
The wings and hook are completely my own design as they were missing from the wreck. Made some modifications to the undercarriage to make it more durable.
Print approx. €3.54–€4.33 excl. taxPreliminary estimate for PETGSource material: PET
The brackets of the cable routing got brittle so I decided to redesign and 3d print them. Now my retro garrett headphones are like nw. You can re-use the screws and nuts. More infos on my blog:…
Print approx. €0.80–€0.98 excl. taxPreliminary estimate for PETGSource material: PET
TL;DR A broken plastic part with less than 1 g has been redesigned and 3D-printed, thus avoiding 975g of garbage in the form of a defunct mixer. Machine to repair Our Siemens hand mixer MQ90001/02 broke about 3 years ago. Thanks to the…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for one variant
Commonly failing plastic components in motorhome window blinds can be a persistent issue. This repair kit provides a durable, 3D printable solution to replace worn or broken parts, restoring full functionality to your blind system.…
Print approx. €0.95–€1.16 excl. taxPreliminary estimate for PETGSource material: PET
EN : To avoid to trash my glue gun, I realise this fast print to repare the little part who connect the trigger and the glue stick actuator of my glue gun, I dismantle it and take measurement and then conceptualised with F360 the model…
Print approx. €0.09–€0.11 excl. taxPreliminary estimate for PETGSource material: PET
During replacing of the batteries of the hue dimmer switch V1 the very weak strip of the main housing was brocken. Because of that, the battery cover does not mount anymore in the right way. With this part the problem is solved. Während…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for PETGSource material: PET
EN: Yesterday, the connection piece of the hose of the above-mentioned blood pressure measuring device broke off. A replacement was needed. Here is the result. It works. Could be that it also fits other devices. The inner diameter…
Print approx. €0.13–€0.16 excl. taxPreliminary estimate for one variant
The part is printed with PETG. Print instruction: supports: YES | default setting recommended layer height: 0,2mm nozzle diameter: 0,4mm brim: YES (recommended to ensure good adhesion on the print bed) enclosure: NO Assembly instruction:…
Print approx. €0.51–€0.63 excl. taxPreliminary estimate for PETGSource material: PET
Vytvořeno na opravu ulomeného zámku 4pin konektoru Fabia 1 (6Y5) palivového čerpadla. Mělo by být kompatibilní s dalšími starými modely koncernu VAG (VW/Audi/Seat/Škoda)
Print approx. €0.25–€0.31 excl. taxPreliminary estimate for PETGSource material: PET
This model contains two parts - one is the motor yoke to hold the motor, and the other is an insert (print in TPU) that provides some grip and shock transmission. My West Marine transom saver had fallen down and dragged the road - and the…
Print approx. €9.95–€12.16 excl. taxPreliminary estimate for PETGSource material: PET
Part can be printed in two pieces without affecting functionality. Attached are both the two piece and one piece model files. One piece print will require supports, two piece will print without, just add brim and print. On the two piece…
Print approx. €10.96–€13.40 excl. taxPreliminary estimate for one variant
Repair of the postal lock key The plastic handle of the key is broken. It was based on the keychain of the author of the Modern Key Hanger model. The size of the inserted part of the key is 8.6 mm x 1.7 mm I printed myself in brown…
Print approx. €0.45–€0.55 excl. taxPreliminary estimate for PETGSource material: PET
This repair module for the Sigma ROX bike computer can be glued onto the device if the tabs of the quarter-turn mount are broken. Tested with Sigma ROX 4, but should be compatible with ROX 2,7,11,12. Please comment if you have tested it…
Print approx. €0.44–€0.53 excl. taxPreliminary estimate for one variant
With time the wheels of my Craftman lawn mower came loose and got out even if the bolt is in place. The wheel hole now has a conical shape and the back of the wheel is worn too. With those 2 parts no need to change the wheel. The flange…
Print approx. €0.20–€0.24 excl. taxPreliminary estimate for PETGSource material: PET
This is a simple, yet effective repair piece designed to fix broken foldable clothes drying racks. When one of the welded joints on my drying rack broke, I created this bracket to restore functionality and extend the life of the rack…
Print approx. €0.07–€0.09 excl. taxPreliminary estimate for one variant
Erleichtert die Reparatur von Radios und das lästige Umdrehen. Scheiben und Füße "müssen" in TPU gedruckt werden, alles andere in PETG. Mit Scheiben aus PETG, PLA usw lassen sich die Arme mangels Friktion auch mit Gewalt nicht festklemmen…
Print approx. €4.25–€5.20 excl. taxPreliminary estimate for PETGSource material: PET
Hello! Have you ever broken the plastic part of a similar key that you use to unlock your front door at home? If so, you know how much it costs to have a duplicate made. No worries, because with this model, in about 10 minutes, you can…
Print approx. €0.13–€0.16 excl. taxPreliminary estimate for PETGSource material: PET
Sharan spare wheel winch cable guide repair. When the wheel broke down, I discovered that my spare wheel located under the car could not be removed. After disassembly, it turned out that the steel rope that winds the wheel is twisted…
Print approx. €1.48–€1.80 excl. taxPreliminary estimate for one variant
Mount these to your wall for a place to keep your sponges. Long live physical media!
Print approx. €1.69–€2.07 excl. taxPreliminary estimate for PETGSource material: PET
i design it to repair my shower, work by adding teflon on the thread to make the thread water tight SUPPORT NEEDED use 99 wall to print it to make it watertight and use heat resistant filament idealy
Print approx. €2.35–€2.87 excl. taxPreliminary estimate for PETGSource material: PET
Our Miller welding shield's side adjustments broke, so we printed a new part and installed it in under an hour. It is always a good idea to keep consumables around, even small simple pieces like this, so that you minimize downtime in the…
Print approx. €0.38–€0.47 excl. taxPreliminary estimate for one variant
This model fits into the “receiver pods” on the 106 Repair Stand Work Tray add-on for Park Tool bike repair stands and holds a magnetic parts tray. I made two versions to hold either a 4" magnetic parts holder or a 6" magnetic parts…
Print approx. €2.04–€2.49 excl. taxPreliminary estimate for one variant
Vehicles are now more costly than ever. You can make cosmetic repair parts for your ride. You can also use the part as a mold for Body Putty or Fiberglass, or Simple apply the part and be done. You can also use a Heat Gun to make it more…
Print approx. €2.78–€3.40 excl. taxPreliminary estimate for PETGSource material: PET
Suddenly the salt&pepper grinder didn't work. Cause was the broken plastic shaft of the turning top part. The metal quadratic shaft turned inside, as the splitted shaft opend and can't withstand the force. The replacement part is easy to…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for one variant
I have had to fix my mouse "double clicking" a few times before. For mechanical mice it is a relatively simple repair that has good tutorials on youtube already. The repair requires you to open the mouse, open the mechanical switch, and…
Print approx. €0.04–€0.05 excl. taxPreliminary estimate for one variant
SBACH 342 EPO RC airplane repair kit for rudder mounting rudder mount for 12x16mm hinges back wheel steer base For 12x16 mm hinges If you like it, please support me: Paypal: [email protected] Skrill: [email protected] ★…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for PETGSource material: PET
This is a replacement for the Farberware vegetable peeler part that holds the blade. The old blade is use in the replacement part and a pause in the g-code allows the blade to be inserted into the part as it is being printed. The…
Print approx. €0.35–€0.42 excl. taxPreliminary estimate for PETGSource material: PET
I have a snapper model 280812BE (80422) - Snapper 28" Rear-Engine Riding Mower, 8hp I designed this as a drop in replacement part for: Snapper 7022344 CABLE, Brake (Superseded to 7022344YP) The issue is they wanted to charge me ~$40.00 w/…
Print approx. €1.39–€1.70 excl. taxPreliminary estimate for one variant
I found my vacuum cleaner stuck at middle of room with stuck right wheel. When I took it apart, I found that screws what hold wheel in piece jumped out and blocked rotation. They jumped out because threads on opposite side of wheelhalf…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for PETGSource material: PET
The ON/OFF/TARA button of a kitchenscale a friend of mine was broken (just the cover, the microswitch was ok). So I tried to design a new one in FreeCAD and print it. (Sorry for the terrible FreeCAD model, but for me it worked.) I printed…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for one variant
Replacement for a destroyed part that connects the eyelet to the handle Need more padding for greater strength of the part Recommended material for printing is PETG
Print approx. €0.69–€0.84 excl. taxPreliminary estimate for PETGSource material: PET
The stick of my whisk broke and so I modeled a replacement. I printed it in PETG with 15% infill and a bigger rim, just to make sure it will stick to my print bed :) No support is needed. It fits tight and i also used hot glue, just to be…
Print approx. €0.14–€0.17 excl. taxPreliminary estimate for PETGSource material: PET
The tap in our downstairs toilet started to wobble when used. I looked up under the sink and could see that the original metal washer had started to rust and come loose. You can see the rust stains in the photos. Using Fusion 360 and…
Print approx. €0.24–€0.30 excl. taxPreliminary estimate for one variant
The mount on the bit so that it can swing has fallen victim to my sons' play warning. You can renew this with the STL. The old ones that still exist must be removed. Attach with 3.5mm Spax screws about 4mm long and you're done. I printed…
Print approx. €2.84–€3.47 excl. taxPreliminary estimate for PETGSource material: PET
Heat the top of the hanger. Push it in all the way and rotate it while the plastic cools.
Print approx. €0.26–€0.32 excl. taxPreliminary estimate for PETGSource material: PET
Part Fauteuil repas avec coussin chair by Sifas (part of the Oskar furniture set): https://www.sifas.com/product/fauteuil-repas-avec-coussin-oskar/ Story My father has 5 of these chairs on his lake boat, but was dissapointed when the feet…
Print approx. €1.22–€1.50 excl. taxPreliminary estimate for PETGSource material: PET
It's time to prepare summer. Doing it last weekend I discovered that one of the wheel of one of my old deckchair was damaged. It wasn't possible to securely repair it using glue and as usual no way to find replacement or a cheap part that…
Print approx. €0.43–€0.52 excl. taxPreliminary estimate for PETGSource material: PET
The FAO Schwartz Laser Tag electronic game includes a “vest” containing the receiver which signals a hit from the opponent's laser gun. The vest includes straps which connect the receiver via 4 brackets. The brackets often fail as the…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for one variant
Replacement parts for broken suitcase handle, that wont move up and down anymore. To repair, unscrew the handle and replace inner parts. used print settings: printed on Ender 3, 40% infill, Gyroid.
Print approx. €1.30–€1.59 excl. taxPreliminary estimate for one variant
I developed this repair clip as a remedy for your broken Levelor-branded vertical blind “vanes”. I was growing frustrated to find these vanes lying on the floor after randomly breaking at the attach holes. The vanes have a habit of…
Print approx. €0.12–€0.15 excl. taxPreliminary estimate for one variant
A hook for repairing a suction cup
Print approx. €0.26–€0.32 excl. taxPreliminary estimate for one variant
I have a broken shower holder with an oval hole for the main support bar. So instead of creating a new support I just create a new part for the actual one. It's a niche project, I still hope that someday it will be useful to someone.
Print approx. €3.90–€4.76 excl. taxPreliminary estimate for one variant
Summary: Repair of a rolling device for cutlery drawer inserts After breaking the original part, the opposite left part was scanned with RevoScan Mini. The processing was somewhat time-consuming due to the size, especially the…
Print approx. €0.14–€0.17 excl. taxPreliminary estimate for one variant
The interior door "pull" on my Scion XB fell off when I attempted to pull the door closed. After years of wear, the screw hole in the bottom of the pull ripped out completely, leaving behind the screw. I created this insert so that I…
Print approx. €0.17–€0.20 excl. taxPreliminary estimate for one variant
( oprava držáku sprchové tyče)
Print approx. €1.78–€2.17 excl. taxPreliminary estimate for one variant
The “handle” on this Thermos-brand plastic water bottle lid had broken. Constructed this 2-part “shell” that encases the handle and restores full functionality. Actually might be a bit stronger, although it is quite a bit larger. PETG,…
Print approx. €0.51–€0.62 excl. taxPreliminary estimate for PETGSource material: PET
Floor maintenance mops like the one in the picture sometimes break the handle. With this print you can replace the broken handle yourself. Print from a filament of your choice and replace the broken handle with the new one using the two…
Print approx. €3.67–€4.49 excl. taxPreliminary estimate for PETGSource material: PET
repair side for a cardboard reel filament . for laser DFX file and for FDM . size 210 OD ID 40mm thick 4mm
Print approx. €3.94–€4.82 excl. taxPreliminary estimate for PETGSource material: PET
The PCS-10 line of Park Tool Repair Stands have a collar with “receiver pods” to hold the 106 Repair Stand Work Tray. The work tray also has "receiver pods" to hold tray accessories, but they are spaced more closely together than on the…
Print approx. €1.43–€1.74 excl. taxPreliminary estimate for one variant
add some solidol/lithol inside so that it does not jam the spring P.S: I recommend drilling to 6 mm and using M6x25 screws and accordingly nuts
Print approx. €0.48–€0.58 excl. taxPreliminary estimate for one variant
I have a second-hand IKEA wardrobe that's at least ten years old, maybe twenty. It wobbles. Instead of buying a new wardrobe, I made a few brackets and fixed the wobble. Parts Rod holders: to replace the missing Levelling shims: slide…
Print approx. €0.28–€0.34 excl. taxPreliminary estimate for PETGSource material: PET
La petite pièce qui fait contact quand le robot est verouillé a cassé. Découper la partie concernée avec un disque monté sur une mini perceuse. Coller la pièce de remplacement. Pour pouvoir passer le bol du robot au lave vaisselle il est…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant
Lost one foot for the Hama K210 Keyboard - so I made two new ones. The slot with for the foot is approx 18mm In case this is useful for you please leave a like
Print approx. €0.09–€0.12 excl. taxPreliminary estimate for one variant
Robot Select de maytronic
Print approx. €0.74–€0.91 excl. taxPreliminary estimate for one variant
Gusset for repairing Volantex TrainStar motor wall. If you broke it in this place , just print this gusset and glue it with CA glue! If you like it, please support me: Paypal: [email protected] Skrill: [email protected] ★…
Print approx. €0.44–€0.54 excl. taxPreliminary estimate for PETGSource material: PET
Protective Storage Case for Fragile LED Magnifying Glasses (Electronics Repair Goggles) These low‑cost LED magnifying glasses are handy for electronics repair, soldering, inspection, and detailed work—but the frame and head‑mount are…
Print approx. €6.90–€8.43 excl. taxPreliminary estimate for PETGSource material: PET
![Cable Repair and Protect for iPhone and Samsung [lightning+usbc]](https://media.printables.com/media/prints/590112/images/4827822_b916b887-676b-4723-b0c9-90881c40951e_31bb8182-a7ba-4745-adfd-b9d44646baac/195cfe9b-40fc-4570-b695-c540798fc979.jpeg)
