Counting matching models…
This is a tool board protective base with a fan mount for cooling the Orbitool tool board mounted to a Orbiter2 extruder. I remixed it to support a 4010 fan and the umbilical cable. Printed in ASA 5 walls, bottom and top. Orca 2.2.0 If…
Secure the mount to the frame with m3 screws and T-nuts. The threaded hole fits a PC4-M10 PTFE coupling.
This cover was designed to clamp onto the umbilical cable without needing to disassemble the cable. Based on Fiction's Exhaust Cover , but re-implemented in OpenSCAD. Scad files included for customization. Requires adrianschlatter's…
Designed for my own printer, I needed a low-profile umbilical mount since the rear fan duct may overlap the rear profile during movement. the holes are M5 screw holes to be used with M5 T-nuts, i use two M5x14mm screws the hole for the…
This is a top hat for a Voron Trident 300 that I'm calling an Ascot because of the jaunty angle ;-) . This gives extra height for an umbilical setup in the rear yet allows a complete unobstructed view into the chamber while standing in…
this was patched together from 2 files…i made it in mins so it sucks…. but the one i found wasnt actually for pg7 it was too small…
I switched to a CANbus umbilical setup and wasn't happy with my initial solution of sending the umbilical cable through the bottom deck, so I came up with this. The strain relief is meant for the USB cable going to a Beacon eddy current…
PCB holder for Dragon Burner with Sherpa Micro You need 6 M3x5x4 heatset inserts, longer bolts for extruder and 4 M3x8 for carrier itself.
You will need 2x Standard Heatsets and 2x M3 x 12mm SHCS. The Parts should be printed in the orientation shown in the image for optimal strength Note the Standoff and Spacer are unchanged from the original design
This support allows the use of a PG7 cable gland on the StealthBurner toolhead when using the SB2209 CAN board, providing a cleaner, safer, and more reliable cable management solution. The design properly guides the CAN cable, reducing…
Simple extrusion mounted umbilical + ptfe tube holder for the duender. Use with PUG cable strain relief https://www.printables.com/model/378567-pug-parametric-umbilical-gland
Note: This setup works but is not ideal. You should probably remove the Y drag chain altogether. I recommend checking out my final solution: If you can't do that right away, then this part will work and fit nicely. Print using the…
As you may have noticed, the Sovol Zero has an issue where the floppy umbilical cable that goes to the toolhead falls low and prevent proper homing resulting in an errror and alot of unpleasant noises. Some simple solutions exists such as…
Quick Edit to allow for the use of a PUG Gland instead of PG7 in the corner next to the Z Chain for an Umbilical The Y End stop its designed to work with is this one..…
Print using the recommended Voron settings: Sourcing Information | Print Settings. Find the bumper to be mounted on the X Axis here . Use M3×5×4 threaded inserts as provided with standard Voron 2 kits. Min. required: 2 for the PUG mount…
Drop-in replacement for PUG, but more flexible and durable. I like PUG a lot, but one of them broke after using it for a while. (Printed in ASA) I tried using TPU 95A, which is much more durable, but it came out way too soft. This remix…
Only changed the logo to print multi color better without supports
remixed the awesome frame by kyleGB and added a strain relief to zip tie the umbilical cable to.
Just wanted some sturdy strain relief that could be done after assembly rather than remembering to pre-load some nuts after deciding on a mod
EBB36 Umbilical Mount and PCB cover compatible with the LGX extruder without springsteel only flat surface and i enlarged the cable tie openings to get bether fit
You will need an M3x12. You may be able to get away with an M3x13 and two extra nuts on the back, and some cable sleeve to keep all the wires together. I used a ziptie to keep the sleeve at the box where the wires come out, and one at the…
I wanted a better & cleaner way to mount my CPAP hose and the toolhead wiring, and this is what I came up with. Uses a single 8" zip tie to hold everything in place once you screw it into the aluminum brace. You'll need: ABS or ASA…
Looking for mounts for PUG ? Thanks to all users who create mods to run PUG on their machines. If you've designed a mount for PUG that isn't listed below, contact me and I'll add it. Alternate PUG: by pixel shock by nhchiu Toolhead : by…
Overview: This model was inspired by the Farscape1 LUT. New parts have been made to make it exact per the original NASA 75M-05120 and 75M-05121 drawings. The farscape1 model was pretty sparse so many additional parts are provided by…
PUG mount based on hartk's PG7 mount that uses the new standoff mounting location (other PUG mounts hook into the extruder motor threads, which is not recommended). Tested with LDO Nitehawk-SB If you have an SB2209 RP2040 see Ozuwara's…
How did you end up in this dark corner of the internet? Have you built a Voron 0.2 and have noticed the bowden tube rubs slightly against the XY belts? This is a small part that can be bolted to the umbilical circuit board that pushes the…
a screwable mount for the umbilical cord with relocated y-endstop
I was looking for a plate that not only would let me pass the CAN cable to the toolhead but also had passes for extra chamber stuff like LEDs and sensors. Since I didn't quite liked anything I made some right here. What you can choose…
Quick and dirty SB2209/2240 CAN bus umbilical mounting post for Galileo 2 Extruder. Use a M3x50 SHCS to mount the post instead of the cable chain holder, then fixate the umbilical with a zip tie. Print without support to keep the cavity…
Use with the CW2 cable bridge.stl from BTT. Too big to work with the regular cable cover so i added a cutout. You'll have to print it with supports. Add two M3 heat-set inserts into the clamp. Secure with M3x16 screws (or longer, but they…
I widened the vcore 4 umbilical guide and opened it up to accept more wires for the umbilical cable to the toolhead.
Mounts a pg7 cable gland to the trident frame that feeds directly into the extrusion t slot. Added the Archetype logo for added style points.
Keyback umbilical support bracket. printed in ABS. Use two M5x20mm screws and two M5 nuts to replace the existing two top hat acrylic mount screws.
Single tool umbilical plate that is designed to work with my Stealthchanger umbilical restraints and covers
Hello, I had an Orbiter 2.0 with the filament sensor add-on, and I needed to add strain relief for my umbilical. I could not find an Orbiter 2.0 strain relief model that added a port to accommodate the Orbiter filament sensor wire…
This is an exhaust cover for a Voron 2.4 with threaded mounting holes for both a PC4-M10 Bowden tube fitting and a PG7 cable gland for a CANbus umbilical. I printed it in ABS with a color swap to use the primary and accent colors of my…
Mounting bracket for umbilical with a PG7 mount for Stealthburner / Clockwork 2. Puts the end of the cable in a reasonable spot for an LDO Nitehawk SB. Easiest to print upside down.
Retractable Keychain 2020 holder for umbilical cable.
Plate that holds fysetc ucan board in place, with holes for daylight wires to pass through.
Added a guide to the center to use an umbilical style feed for the hot end. This should allow for taller builds and reduce rubbing and kinking of the bowden tube.
This remix allows the use of a LP-12 connector on the gantry. I used this Rear Umbilical with PG7 mod.
This is a tool board protective base with a fan mount for cooling the Orbitool tool board mounted to a Orbiter2 extruder. I remixed it to support a 4010 fan and the umbilical cable. Printed in ASA 5 walls, bottom and top. Orca 2.2.0 If…
Secure the mount to the frame with m3 screws and T-nuts. The threaded hole fits a PC4-M10 PTFE coupling.
Voron 350 center skirt with 5 integrated Wago 221-2401 connectors in rear center skirt for quick disconnect. Added a klipper expander version The 5th wago is for 12v output from the mcu to run delta part cooling fans 300 version…
Voron 300 center skirt with 5 integrated Wago 221-2401 connectors in rear center skirt for quick disconnect. Added a klipper expander version 350 version please leave ⭐ review and rate. https://cults3d.com/en/users/3DeezNutZ/3d-models…
I have remixed tetsu97 's umbilical mount for G2SA with PG7 fixing point by moving it to the right. Added channels for zip-tie that is meant to secure the umbilical cable. The stl is print oriented and includes sacrificial support (in…
I remixed the original A motor cable cover with PG7 threads in order to attach a PG7 gland for umbilical setup.
Requires the following hardware 2x M3x4x5 Heatset inserts 2x M3x8 SHCS Part A needs supports to print correctly.
Printing options: Use ABS/ASA/PETG Voron definition BOM: 4pcs M3x12 HEX SHC screw 2pcs Hammerhead/slideing insert M5 2pcs M5x10 HEX BHC screw
Galileo 2 stealthburner umbilical mount for CAN Cable and steel wire mounted on standard 2 hole cable_chain. https://github.com/JaredC01/Galileo2/blob/main/galileo2_extruder/stl/cable_chain_2_hole.stl
The original LDO model is good, but as I watch my prints, I started to get uncomfortable with the amount of movement that the wires are seeing right at the connector. This is a common failure point for a moving cable, and I wanted to…
Ich habe das teil so konstruiert das es möglich ist die kabel ohne den Klavierdraht oben zu halten.
This is the Super Stealth Orbiter, a super low profile mount/housing for your Orbiter 1.5 + voron stealthburner with easy access for servicing the Orbiter without removing it from the printer/housing. Features To have an unbroken PTFE…
This model pairs with Cliftoce's Voron Trident Horizontal Umbilical Chain . It runs much quieter than stock, at around 38dB. BOM For fastner sourcing, I've found the following to be good places: AliExpress – slow delivery ~2 weeks…
Background After switching my Trident over to using a CAN toolhead and removing the X/Y cable chains, the one thing that I wasn't satisfied with was umbilical wire management. Unlike on the Voron 2.4, piano wire isn't very practical since…
I wanted to mount my umbilical to my gantry. It seemed like the best way to minimize its run length and avoid getting it caught in my z-chain. I couldn't find an existing STL, so I hacked this together. It's not a work of beauty, but it's…
Might want to test different top infill patterns to change the look and feel but sanding up to 1500grit will give a texture similar to a matte plexiglass. I recommend adding a chamfer to get a snap fit. These are the recommended settings.…
Inspired by the STLs provided by the Voron 0 Umbilical and the Voron 0 Umbilical Plus https://github.com/VoronDesign/Voron-Hardware/tree/master/V0-Umbilical https://github.com/skuep/V0-Umbilical-Plus The Umbilical Strain Relief Frame v1…
I needed the PUG connector to the left of the Bowden tube as I am using a BTT Filament Runout Sensor V2, and having the PUG cables near center would collide with sensor. I started with the design from Impact 3D@3DImpactt as it already had…
Needed the larger gland in order to use the 3DO CAN Bus + USB cable, as well as I wanted to attach a fiberglass rod to the cable through a cable sleeve to keep the wire from sagging. I am Paring it with another remix I made…
This is an umbilical mount for the back of the RatRig V-Core 3 or 3.1 that is compatible with Enclosure 1.0 for those few of us who have it :). I decided to fit my printer with RatRig Printhead 1.0 for the V-Core3.1 and that presented a…
The mount fits into the right z_bearing block, but you will need longer M5 screws (+1cm). It allows to use all PUG models. You will need to print the modified part with supports. Otherwise print with Voron settings.
Uses a PUG for cable strain relief https://www.printables.com/model/378567-pug-parametric-umbilical-gland Uses https://www.printables.com/model/506687-wago-221-415-mount to mount wagos. Mounts into…
I designed and use these for my Nitehawk-SB based Stealthchanger build. Print from ABS/ASA or other high temp/strength materials. Uses two 2mm wide zipties for indirect tensioning. Allows for two 1mm lengths of piano wire to run through…
This is a replacement exhaust plate for the Voron 2.4 intended to allow umbilicals to pass into the print chamber. Print from ABS/ASA. Requires modification to rear enclosure panel, three M3 heat set fittings, and three M3x8 SHCS.…
After about 100 hours of printing one of the wires on my umbilical wire harness broke at the Molex pin crimp. Turns out this is fairly common if strain relief at the frame end of the Voron 0 is not sufficient. I had to modify the original…
Found many different versions, but none met my specs. So I designed my own. You can mount a EBB36 board behind a Galileo 2 standalone extruder stepper. In my case on top of a XOL toolhead. Umbilical is placed besides the boad to not lose…
2 hole mounts to be used with IGUS Chains
Remix of Mauxx91 's Umbilical cable cover to add compatibility for PG9 or PG11 cable glands
There are other solutions but I couldn't really find one that uses PUGs and didn't have the toohead umbilical routed so I made my own clamps. The bottom clamp can be used on the gantry side as well if you don't have the wires routed in…
Ended up with this when I moved to sensor-less homing removing the cable chains. This is not designed to fit stock rear panel. It will forfeit at least 20mm of Z height. It may rub wires long term No supports Built in counter bore…
this uses the motor mount screws so no added hardware simple take the 2 screws out put this in place and tighten back down. run wires down through the gantry motor cutouts and up through your cable chain on the z axis and you're good to go!
This is an arm that holds bowth of my cables, nitehawk sb and btt eddy, they are going within the extrusion chanels and coming down from the top. The arm itself holds the cables by using zip tie. 3x2.6mm zip tie 1xM5x16 Bolt SHCS 1xM5 Nut…
This is an 'Overmold' style strain relief for 14 and 16 pin microfit connectors, commonly used for umbilical and FYSETC Catalyst toolhead PCBs. Use the 14 pin for common Umbilical (i.e. LDO), and the 16 pin one specific to Catalyst V1.…
This cover was designed to clamp onto the umbilical cable without needing to disassemble the cable. Based on Fiction's Exhaust Cover , but re-implemented in OpenSCAD. Scad files included for customization. Requires adrianschlatter's…
I just deleted one hole from the original so I could use on the rear without the PTFE tube and without leaving an empty hole. I kept the bump to make it easier handling the clip when you take it out. PS: Assembly-wise, I used a cable…
PG9 without thread Please use two suitable M3 screws to tighten
Designed for better seal (3mm foam), umbilical through PG7 and PTFE through PC4-M10 connector.
Print using standard Voron settings. Hardware: 2 - M3 inserts - Voron Spec (M3x5x4) 2 - M3x16 SHCS 1 - M3x25 SHCS
Credit goes to https://github.com/N3MI-DG who made the Voron version of this file. I adapted it to fit the sv08 with https://mandalaroseworks.com/products/sv08-back-panel-voron-style The supplied files assume the docks are spaced. This…
There are six options to choose from: umb_ptfe_wire_ziptie.stl has spots for an umbilical cable, PTFE tubing, and a music/spring wire. umb_ptfe_wire.stl same as above with no ziptie. umb_ptfe_ziptie.stl has spots for an umbilical cable…
LDO Nitehawk Umbilical Exhaust Plate for Voron 2.4 - 4 Toolheads I modified this for a Stealthchanger with 4 toolheads (still working on it) Print off the original PG7 blocks (add a little lubricant in the tracks for ease) Hardware: 5 M3…
Heat set inserts are now installed from behind the plate. Additionally there's “_short_offset” file, I noticed that the rear holes were not aligning with my micron carriage, so I moved the holes 1.5mm up to better align.
This remix was made to allow usb connection with BTT SB2209 toolhead board as the original model blocks the USB input. PUG Clamp and Bottom Standoff parts as exactly the same of the original model, but I provided them here for…
Modified the original back centre skirtpiece to allow for a umbilical passtrough. You can pair it with this excellent parametric design by @10suo_330679 : https://www.printables.com/model/862631-parametric-umbilical-passthrough. hole size…
Connector protection against ejection and cable protection against cable breakage Update: I added another version of the cable holder. The cable is attached with a clip on the other side and there is more space for the toolhead to travel.
- Cable holder for Umbilical - Also includes ADXL PCB holder - You will need 4x threaded insert
This is my take for read umbilical modification for Voron V2.4 printers with Funssor CNC motor mounts (see attached photo to confirm that you have compatible motor mounts). This model will not fit printers with official AB motor mounts.…
Remix Details: Improved chamber seal, rear panel is now sandwiched between the cover and trim when tightened. Bowden entry threaded for a PC4-M10 fitting. Added a PG7 Key for easier tightening or removal of PG7 strain reliefs.…
Dopo tanto tempo, finalmente nel 2021 comincio con la realizzazione del complesso di lancio della missione Apollo. Questa è la sezione didicata alla LUT (Launch Umbilical Tower) che permetteva l’accesso alle parti più importanti del razzo…
Modified the LDO Nitehawk Umbilical Clip to use 3mm wide by 1 zip tie.
Designed for my own printer, I needed a low-profile umbilical mount since the rear fan duct may overlap the rear profile during movement. the holes are M5 screw holes to be used with M5 T-nuts, i use two M5x14mm screws the hole for the…
Checked a few models online, none quite fit my idea perfectly and most where a bit bulky for my taste. I took some ideas and modelled these to fit tightly and be as small as possible while sturdy enough. Print the parts in the orientation…
Intended for use with the large gear clockwork2 designed by nhchiu.
cable clip for ptfe tube and cable to toolhead. i use it with cable tie 9mm
I found the existing options for cable relief of the BTT EBB SB2209 USB were lacking in one way or another. So I made my own. My goals: Relieve strain on the umbilical cable. Compatible with the PUG system. Allow greater access to the…
This arm uses two F623 bearings, which are usually used to attach a drag chain to Stealthburner (which you don't need anymore because you are switching to an umbilical set-up). You can use one or two piano wires up to 1mm with this arm.…
