Liczymy pasujące modele…
No supports required! Designed to minimize filament use, while maintaining strength! Entire print fits inside a single Prusa MK3 bed! All perimeters are sized to perfectly print with two perimeters with zero infill! (except the base…
Wydruk około 5,69 €–6,96 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Edit 2026 - added a new model which doubles the thickness of the walls to 2mm (four walls) - should hopefully add a bit of resilience! As the guy stuck with maintaining our communal driveway's gate (how? why?) I was getting tired of…
Wydruk około 2,60 €–3,18 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Are you feeling overwhelmed by your monitor taking up too much space on your desk? It's time to take a stand and reclaim your workspace with this French cleat, low profile monitor wall mount. This mount is designed to be both strong and…
No supports required! Cut the positive and negative wires, and terminate them in one of these blocks. Then connect the block to a 12v USB boost - USB Boost Line Power Supply Module 5V To 12V Power Cable Depending on your fan model, you…
It’ll be a cold day in hell before I waste my precious PLA on support material. After countless iterations, I’ve nailed it—a snug, snap-fit under-desk mount for the Ubiquiti USW-Flex-Mini gigabit switch. Prints in 37m51s on my P1S, using…
Adjusted this excellent model to fit this generic 7 Inch LCD touchscreen from Aliexpress - specifically the IPS version. 7 Inch Raspberry Pi 4/3/2/B/B+/A+ Monitor 1024x600 IPS 5-Points Capacitive Touchscreen Drive Free HDMI Display For…
While the G3 Bullets are weatherproof, it can't hurt to protect them from the elements. I use this shroud to protect my G3 Bullet while captuing an outdoor timelapse of the countryside, attached to a pole on my roof. UPDATE: Added slotted…
Honestly, this design isn't super great.
Everybody knows that dogs are better than cats. But did you know that Schnauzers are the best dogs? This is a leash hanger, with an adorable Schnauzer's face. Uses Prusa Slicer's built-in filament-colour changing feature alongside…
Covers the busbar (and the nuts!) to reduce the chance of a short circuit. Available in 2x and 4x cell configuration. Friction fits on 11.2mm nuts - this allows clearance on any BMS wires/attachments. No supports required - designed to be…
An idiot (me) ordered these cameras expecting the cable to pop out of the side - aka, I could sit them on surface - NOPE. The only way to use these cameras is to drill a hole in a surface, then screw the camera to said surface. … not…
Great model, just remixed to remove the requirement for supports. Also reduced the depth of the threads to ensure printability.
Surprisingly sturdy, this set of legs elevates your RØDECaster Duo approximately 10mm off your desk, positioning it at a comfortable 45-degree angle while freeing up valuable desk space. Printing Instructions: Quantity: Print two of each…
Apparently I'm the first person in the history of the internet to want to mount an Orange Pi Zero to my Prusa MK3 frame. Huh. Print at 0.2mm, no supports required. Needs 2x M3x8mm bolts to screw into the Prusa frame, just above the…
Print standing up. No supports required. More perimeters, the better. Designed so that the “last” hanger or two sits on the stop itself, holding it more in place. The rod used for the ELFA is 25mm - this design is 24.5mm, so snaps on…
Well, this might be the dumbest (but most useful) print I've ever designed. Long story short, I wanted a 6th Gen iPad in my kitchen to display my Home Assistant Dashboard. Decided I didn't want to put any holes in my wall, nor did I (or…
Replacement garage door wheel for ProfessorPetulant
Illustrating how to include a belt clip without relying on layer adhesion, as per this thread. Holds 8x 6.5mm diam arrows. - print auto-orientated, no supports required.
Remove the magnetic cover from the front of the device. Pull the top of the joystick off, leaving behind the flat "nub". Unscrew four small hex screws, two on top, two on bottom and put them somewhere SAFE - they are VERY difficult to…
Print flat side down. Uses existing screw. Modeled after the original foot. Printed example with fuzzy skin - Contour, Combined, Voronoi, 4mm feature size.
To wszystkie aktualnie dostępne wyniki.
