Liczymy pasujące modele…
A very quick remix of the BentoBox base w/magnets and an additional magnetic wire guide for use in the Elegoo Centauri Carbon (though both will likely work on other printers). Uses the same magnets as the BentoBox itself (since you likely…
Just a quick and dirty adapter to convert the 2510 mounting to 3010. This is mostly intended as temporary solution while you wait for a 2510 fan to come in the mail, as I do not have them on hand readily as none of my other printers use…
Simple latching clamp/clip used to prevent PTFE tubes from being pulled into driers or AMS units. Printed in PETG, PLA may work but was not tested. Simply clips over the tube and locks. If you have issues with it being overly tight on…
JST-XH 2-pin boot for male connector for use making inline connections for fans, thermistors, battery packs, etc. I could only find male 2-pin JST-XH connectors as pigtailed assembled connectors, which meant I'd have unnecessary…
Simple desiccant holder that can also fit a hydrometer. Cap is built in two sections, the main cap ring and the bottom snap-in “floor” to the cap. This is so that everything can be printed with no supports. The bottom desiccant cage…
This X-axis cable chain mount for the Anycubic i3 Mega Pro was designed for use with the cable chains in Anycubic I3 Mega - Cable Chains - All Axes by dmaMods . The mount included in the original did not fit the Pro version of the i3 Mega…
Bottom feed desiccant holder for cereal box drybox. This is intended to be used with a top-mounted drybox shelf such as Drybox shelf for Anycubic i3 Mega by clickbangdead . It should fit the cereal boxes used for dryboxes like: Dry boxes…
This is a Side Shelf for the 46" x 18" Husky mobile workbench cabinet. It is designed to mount to the side of the workbench using the existing holes and M6 bolts. Two 8mm or 5/16" rods are used to attach the center shelf to the two side…
This is a PCB Standoff for the display in an Aquarite salt system. The originals in my system had degraded and snapped. I whipped this up quickly so I could get the device up and running again, there could likely be tweaks to get them to…
This is a hotbed carriage for linear rod upgrade for the Voxelab Aquila printers Y-Axis. This is designed to be used with the Y-axis rod mounts from https://www.printables.com/model/446502-ender-3-v2-x-and-y-linear-rodshaft-upgrade. This…
This is an enclosure and mount for the HBVCAM v20234 v22 for Qidi X-Plus. It mounts directly under the front lip of the top cover where there is a pre-formed screw hole in the plastic housing, so no drilling is required (see pictures).…
This is a hotend mount for the KevinAKASam Frankenstein Duct. This was specifically designed to allow the use of a cheap Bambu labs X1C (or P1P/S) style bare hotend rather than the more commonly recommended TZ V6 hotends. The base mount…
This is a new motherboard mount for the Geeetech A20M to allow installation of the Big Tree Tech SKR 1.4 along with a Pi Zero 2W form factor device and MP1584 buck converter. Main features are: The microSD card of the Pi is accessible…
This is an internal bracket for the Anycubic i3 Mega Pro that replaces the existing SD card reader with a mount for a Zero 2W formfactor SBC (Rasberry/Orange/Banana, etc.), allowing the Pi's microSD card to be accessible from outside (for…
This is a remixed touch probe mount for the der Skorpian fan duct (https://www.printables.com/model/18904-der-skorpion-fan-duct-for-geeetech-a10m-and-a20m-d) for the Geetech A20M to allow the use of a 3DTouch probe. The 3DTouch and…
Adapter for 7 inch felt filter bag to attach to a 1 1/2" PVC connection for use as a pool slime bag or dust filtration. I made this adapter for this 7" X 32" felt filter bag: https://a.co/d/hf8bH57 This had a plastic collar that this…
This is a set of stabilizers for the Geeetech A20M for use during/after conversion to KevinAKASam's Belted Z mod. It is intended that for one of the stabilizers you use the 355MM leadscrew as part of the stabilizer, while the other…
Bentobox mount for Qidi X-plus. This is made to fit on the left side of the printer; it friction fits in a gap in the panel and shouldn't require any holes or drilling. There are two holes for heatset M3 inserts, I used 8mm depth ones,…
Spool Spacer for Qidi X-Plus for use with carboard spools on the internal spool holder. When using some carboard spools with the X-plus's internal spool holder, they can get jammed if they have a lip or overhang at the spool hole (see the…
I made this case for these multimeter needle probes: ANENG PT2003 Pen Extension Needle Tip 1 Pair Probe Tip Test Fine tip 1000V/10A Bendable Probe Detachable Accessories Tester Tool - AliExpress 1420 May work with others, step file is…
This is a simple Print-in-Place V6 nozzle organizer. There are holes that the nozzles slip in, then a rotating strap that holds all the nozzles in place. Detents are used to make the strap stay in the locked or open positions. Nothing…
To wszystkie aktualnie dostępne wyniki.
