134 modeli
Bulkhead inlet mount for 2 SO-239 Connectors with the flanges. making this for a friend who was putting his HF radio into one of those black plastic Harbor Freight Tools brand protective carry suitcase.…
Wydruk około 1,01 €–1,23 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is the bulkhead fitting needed to install a valve in the wall of a rain barrel. While commercial fittings are available, they can be expensive. The ID of the fitting is sized for a ½" pipe thread valve (very common in the US). The OD…
Functional bulkhead and cap model that doubles as fidget toy, or workspace decor. Ideally printed without supports. Can be used functionally when printed with appropriate material like ABS, the gaskets should also be printed in TPU or…
A PTFE Bulkhead to cover the PTFE entry slot and not put any additional stress on the PTFE lines uses 8 - PC4-M10 Fittings and 2 - m3x10mm thread cutting screws (steal 2 from the top of your enclosure)
Manpack Rail System for RT95/AT-778UV – 3D Printable File Hey everyone, I’m excited to share my latest 3D design—the Manpack Rail System for the RT95/AT-778UV ! As a passionate Ham radio operator and off-roading enthusiast , I wanted a…
Back nut that is suitable for Foster and PCP bulkhead connectors. Specification: 1/8 NPT thread 3/8" diameter thread 6.4mm nut height 15.8mm nut outer diameter Print high infill, no supports required 0.1 layer height, but works on 0.2…
WIP ! WATCH THIS THING in case of updates. This is my version of the 1995 bulkheads that were designed for Necromunda (but re-used in latter boxed sets). They were designed to work with cardboard pieces to create platforms, catwalks and…
Low profile "bulkhead" style screw in place vents for terrariums/vivariums. The mesh features 1.2 mm holes with 0.8 mm ribbing. Both the insert and nut have M28 threading with wide tolerances for easy printing. The low profile design is…
This lets you make a connection from a 1/2" poly hose to a tank. Instructions You'll need to add a garden hose washer so that it won't leak. Print it with a 100% infill, otherwise the bottom of the connector may break off as you tighten…
A Gunderson-style straight taper bulkhead. I designed them to slide onto the ends of an LGB long(54' in 1:29) flat and snap in place. They fit best if the top of the stirrup detail is shaved off. Ladder, Grabs and Brake parts best printed…
Printed with CF-Nylon or ASA vor high strength. For 25mm inner diameter tube / Für Schläuche mit 25mm Innendurchmesser. Printer Settings: Printer: Creality Ender 2 Infill: 100% Supports: No Raft: / / Speed: slow 25mm/s Material: ESun EPA-CF
This is an Anderson Powerpole connector designed to take two sets of connectors. It can be used for passing through a bulkhead up to 20mm thick. Includes Nut. This is the final competed model Fixes from previous models: Thread depth…
This is a bulkhead fitting for connecting flexible hoses to containers. It is designed to allow for easy drainage, since the existing parts I found available didn't allow for good drainage due to surface tension around the inlet. You…
Generic filament bulkhead for building a dry box. Inspired by the many variants available on Thingiverse , I wanted a simple bulkhead to guide my 1.75mm filament out of my dry box. I came up with a few variants while experimenting with…
This is for XT60 bulkhead connector, it allows to mount the connector inset into the trim. You can glue it to your surface or use sealant to mount it with screws.
General The 25mm version is compatible with 1 inch cable grommets as shown in the picture below as well as M25 cable glands. But you can use the blank plate to remix your own version if you have different needs for your car 😄 The gasket…
Bulkhead fitting for filament dry box, using the magnetic joiner concept. requires a 12mm hole, 5mmx3mm magnets, qty 6 per bulkhead fitting and cover, available from Amazon : 5mm dia x 3mm thick N42 Neodymium...…
Adapter na 3/4" hadici, šroubovací průchodka M36 Vrtám díru 40mm, tloušťka stěny nádrže je cca 3mm. Doplnit ploché těsnění s vnější strany , závit netěsní na 100%. Z vnitřní strany není nutné těsnit. Hadici před nasazením nahřát, aby…
While this is registered a s a remix, it is actually a completely new set of models with STEP files included. There are two versions. The threaded version is designed for use with standard g 1/4 fittings for water cooling. The three small…
Updated to have better socket retention and more solid clip engagement. This is an ATX 24 pin bulkhead pass through for the Thermaltake Tower 900 case. For securing ATX 24 extension cables. The rubber grommets from the Tower 900 case can…
A niche design for cable bulkheads or glands, for those cables with large molded connectors. It's base size works on HDMI cables, and can be scaled for a range of sizes (I've tried 60 up to 110%) The flat part of the cores may need to be…
I needed fittings to pass wiring through the bulkhead on my printer controller case. I came up with these 5mm and 7mm fittings. I printed mine at high resolution (0.15mm) on a Malyan M200 using Solutec PLA at 205C on a 60C heated bed…
Fixes from previous models: Thread depth increased for improved thread definition. Thread changed to standard right hand thread (earlier prototype was accidentally made with left hand thread) Thread width: 25mm Body: 23mm Flange: 35mm…
This is a grommet insert giving you a bulkhead that will accept two 8-pin ATX power connectors. Either EPS/CPU or PCIe are compatible. This secures the cable and gives it a very clean look. The design allows you to run extensions from…
As the original Tamiya parts seem to be unobtainable in Europe at the moment I designed this parts for my Daughters DT-02 Nissan Titan RC Stadium Truck. It is a direct replacement and seems very strong when printed with 4 outer layers in…
Allows you to create a watertight (when using gasket/o-ring) seal to a rain barrel or bucket which allows you to connect 1/2" propylene tubing for overflow or tap. I used PETG and “99” walls to print it to help prevent any leaking. I used…
I needed a 4in duct fitting after installing my AC Infinity AC unit as there were no more pre installed holes. This worked great. I used 5mm brass inserts in the plate. printed with the shorter length down with supports. The nut plate…
This bulkhead lets you embed a USB-C PD Fixtured Voltage Module inside of itself allowing you to use a USB-C charger at a fixed voltage based off the type of voltage module you purchase. Simply take the module and place it inside of the…
A simple bulkhead/passthrough model for PC4 1/8" BSP compression fittings. The hole in the nut is sized appropriately for a 1/8" BSP tap, though you may be able to get things to work with a 10x1mm. These fittings are pretty much always…
3mm panel x 4mm bowden tube. 10.5mm minimum to 12mm maximum hole diameter required in panel Print instructions .2 resolution .3 initial layer height, Printed in PETG 15% infill, no supports. Collet cone points up, Collet Nut Cone Prints…
Simple bulkhead lamp for models. This light fixture is about 30.2x15.2x11 mm in size, and therefore roughly scale 1:8. Made for two 5mm LEDs, you might need to sand the top of the LED to have it fully seated. Picture shows an XT-60…
The AD5X partition, passing through a through-wall made of PTFE with a 45-degree rotation. Displacement of the tubes in the middle of the part. added a sleeve inside the case/ PC4-M10 pneumatic fittings are used print vertical thread
Bulkhead for my formicarium for 11mm tube Print Settings Printer: Creality Ender 3 Rafts: No Supports: No Resolution: 0,12 Infill: 10% Category: Hobby
I wanted an external USB connection for my Hiker Trailer to power some awning lighting, but no one makes what I was looking for. This was printed with Prusament PC Blend and NinjaFlex Chinchilla. The design is similar in appearance to…
I designed this wall/bulkhead mounted shelf or tray to hold my reading glasses in my boat but it could equally be used at home or workshop. I fitted it below deck but there is no reason it couldn't be above deck as I have included a drain…
Files will print a ship's clock case that will accommodate an inexpensive quartz movement available from Klockit or Amazon. Included are multiple spacer and shim options for different clock shaft lengths. The clock face requires a…
Originally designed for a Startech.com 6U wall mount server rack. But should work with their entire line of wall mount server rack products. It's a two piece design. You can installed the CAT 6 terminated or unterminated it doesn't…
Bulkhead for adding a blow-off tube or bunge to any plastic surface such as the lid for a five gallon bucket. I didn't find anything like this online and I needed it for the top of a blowoff bucket that I was making. It would work as the…
This is an alternative bucket mount for the patio strawberry hydroponic planter. Requires 6 M6x1x30mm bolts and washers. This is in 2 parts. There is a under lid ring, and a top ring and adapter.
This is intended for mounting under an RV / camper trailer, screwing it to the underside of the electronics bay, providing a good place to mount a RJ45 through bulkhead mount. This provides a weatherproof connection point to bring…
Bulkhead fitting contoured to the shape of a 4" PVC tube for a better water seal. Will update the description with the o-ring sizes that I used. My other 4" PVC pipe designs: Hydroponics 4" pipe clamp for use with 3mm paracord Hydroponics…
After some brainstorming and wanted a alternative for a bulkhead i came up with this diy bulkhead this should be as efficient as a normal bulkhead though using existing pvc couplers since bulkheads are not available where i live this…
Use the notched connectors to prevent rotation. Include single and double connector versions. Double version comes with a short mount. Secure with a piece of filament: align the connector with the face of the print, make sure the…
I've resized the hole to fit a standard 4mm PTFE tube. I don't like the noise or scratching sound when the filament slides through the original hole.
UPDATE NOTE 12/18/2025: The initially uploaded model had a misplaced retention pin hole. It could be used, but was not optimally placed with regard to the retension ribs. The 12/18/2025 upload corrects that issue. Please note the pin hole…
This is a 1 wide by 2 slot antenna mount for a BNC Female Bulkhead radio antenna connection. This will allow you to move where the antenna is located on your person and keep it out of the way, such as mounting the radio antenna to your…
Nothing clever to add here that wasn't clarified in the summary. Pretty straightforward part to be honest, definitely not tens of hours of work and 50+ features.
4-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match terminals…
Replacement part for a Second Hand for Smiths Ships Bulkhead Clock - looks the same as the metal when printed in black and installed on the clock. Sized to gently push on.
Buddy wanted to add some airflow to his dinosaur costume. Designed this to be installed onto the costume for air flow. Fit in place, punch screw holes and use M3 screws to hold in place, then cut out the center fabric for the vent
I added some threads to the original design as well as adding some material to buffer the filament from any potential rubbing against the fitting edge. The size was scaled up 104% in the X and Y directions and 101% in the Z direction. I…
The weak point of the Team Losi Racing 22x4 4WD buggy has always seemed to be the front gearbox/bulkhead, often breaking to leave the shock towers ‘floating’ above, and the repair is not quick during a race event. These simple braces act…
I wanted to connect my Creality Space Pi Filament Dryer Plus to my CORE One Printer. The dryer comes with rubber pass-throughs which work OK, but allow the PTFE Tube to slide in and out of the dryer. I wanted to capture the PTFE Tube so…
I lost the bulkhead for my flex and couldn't find one. Save yourself 10$ and just print this one. I used this nozzle with it. Enjoy. https://www.printables.com/model/819851-fluval-flex-15g-low-flow-spray-bar Supports aren't necessary,…
For other Prusa MMU stuff: https://www.thingiverse.com/AbeFM/collections/abes-mmu2-stuff I have used a lot of bowden style feed-throughs that use purchased parts. These can have small outlets which drag on filament. I wanted something…
Quick 1/2" PVC pipe bulkhead. Needed a version with a pass-through hole. Mounts with four #8 screws. Very slight taper on the inside surface so you shouldn't need to fuss with printer tolerances too much. Banana for scale. 1.100"…
I designed this to allow my filament to enter my enclosure while keeping things pretty well sealed. Fits a ½" hole (say 12mm?) and threads together using hollow M10 threads. each piece accepts a 10mm bowden PTC fitting (which doesn't use…
This is a two piece "clam shell" fitting that encloses the stock humidifier hose that comes with the AC Infinity humidifier. The fitting is then clamped around the hose and held in place a nut. Works great!. I've added two nuts, one with…
This is a Bulkhead shim for a Team Associated B6 / B6D. It goes between the chassis & bulkhead, you can choose between 0.5mm & 1mm. It provides a smoother steering response and increases mid-corner steering. Some may find 1mm to…
I designed this for my CNC router enclosure i made out of 80/20 to run the suction hose threw the top of the enclosure. printed at 50% infill and uses 1/4-20 hardware. Category: Machine Tools
This bulkhead is designed specifically for LOC/Precision 4-in (102mm) body tubes. It was designed specifically for use with my 4 inch coupler but will work with paper couplers of the same size. It has been tested to work with Apogee 4-in…
B6 Bulkhead Ist jetzt nur eine einfache gerade Version die sogar bei einigen neuen Modellen mit 0° Standart ist. Wer unbedigt die 25° oder 30° haben möchte muß dann das Original kaufen ;) ---------- It is now just a simple straight…
This is an electronics tray and bulkheads for the BlueRobotics 6" ROV (149 cm inner diameter of cylinder). The Bulkheads are modified from the ones supplied by the BlueRobotics website for the 4" model. NOTE: I was unable to attribute…
Grow tent duct bulkhead with holes for a 120mm fan. 50mm & 75mm versions. 50mm just a bit short for me. Fan I used out of the computer didnt work for me.
This model is a panel or bulkhead fitting for two anderson 45A powerpole pairs. It is sized to fit in a 33mm hole in an panel up to 12mm thick. A cap is provided for protection when not in use I printed the Body1 part with the shorter…
This is a stock replacement bulkhead for the KidzTech Yamaha Sr Viper 1:6 scale snowmobile. I have made the A-arms mounting points beefier (my factory bulkhead broke there). Print it standing up, with supports everywhere or experiment…
A little bracket to mount a BNC Bulkhead connector under the shelf of a workbench. Black PTEG. Mounting holes designed for Flathead #6x1 in Wood Screws.
The Estes 1/45 scale Little Joe 2 is one beautiful model, but it has its issues. Even if you've solved the adhesive compatibility problems, you still risk melting the plastic dress-up nozzles when you launch it. One solution is to remove…
The Bulkhead Style Dual NEMA 5-15 Cord Grommet is a single grommet adaptation of the kabeldurchbruch 3 grommet designs. Created a fixture to pass two nema type plug cords in to an IP65 demarcation box housing the smart power strips & my…
Threaded bulkhead access plate, cover and key. Originally designed as an access plate for a custom funerary urn, repurposed for use on a sailboat.
Needed a convenient way to route filament from my filament dryer into my printing chamber so I had the idea to use some heat sets and spare bowden fittings to do this Parts are clamped together using M3 screws and melty inserts Printed in…
This is a fitting for a through-bulkhead vacuum attachment. To work it will need some kind of rubber grommet to make the seal work. This could be used for example to make a simple vacuum chamber from a mason jar (if used carefully).…
UPDATED: to allow easier feeding of filament through, now has inner guide and stop for PTFE tube. Just a bulkhead fitting for the Prusa enclosure, to allow PTFE tube to pass through Uses M10 4mm OD fitting both inside and out. prints with…
This adapter allows a tube to be run through the wall (or cap) of a container. This second version of my tubing bulkhead / panel fitting requires no additional hardware, though is less compact. The body and caps are printed in different…
This model is a panel or bulkhead fitting for a single anderson 45A powerpole pair. It is sized to fit in a 30mm hole in an panel up to 12mm thick. A cap is provided for protection while not in use. This version does not have a flange for…
Parametric 32 mm Pool Filter Hose Bulkhead Connector A fully parametric bulkhead fitting for connecting a 32 mm filter hose through the flexible wall of a small inflatable pool. The connector is inserted from inside the pool. An outer…
I needed fittings to pass wiring through the bulkhead on my printer controller case. I came up with these 5mm and 7mm fittings. I printed mine at high resolution (0.15mm) on a Malyan M200 using Solutec PLA at 205C on a 60C heated bed…
Compression style, press fit bulkhead. Modeled after a Uniseal.
3-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match terminals…
These inserts are designed to help stabilize the bulkhead in an Oru Inlet foldable kayak. The oval-shaped pieces fit between the orange bulkhead and the top of the kayak, providing additional support through friction. They can also be…
Component already rotated for correct print position
Vivarium Vent for Crested Geckos/Arboreal Reptiles
4-inch Fiberglass/Carbon Fiber Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match…
This is a replacement plate for the bulkhead connector/hole in the firewall. Designed to allow for an updated pass-through harness with a seal casket. Designed to use the OEM Clips, OEM connector gasket. Designed to use the firewall…
This is a P9 gland that has a hole for a RP-SMA Female Bulkhead Mount (such as https://a.co/d/9098BcL ) I removed the nut, washer, and lock washer from the antenna extension cable and passed it thru the hole in the gland. I then…
4-inch Madcow Avionics Bay Bulkhead. AV Bay for Quantum Tubing. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for…
5.5-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match…
Estes Rocket Bulkheads Designed for durability and functionality, these custom bulkheads provide essential structure and support for your Estes rockets. Created in Onshape and optimized for 3D printing, they serve as a robust anchor point…
This Bulkhead when fitted to the Honda NT 1100 will enable you to mount 2 * Power sockets under the seat of the NT 1100. One can be used for USB and the other can be utilized for 12v Power the combination is up to yourself. You will need…
Note that there is now a second version of this design. That one requires no hardware, but is a little more bulky and probably a little less robust than this one. Wanted to make a brake bleed container for my car and realized I could just…
Transform your space with this authentic industrial bulkhead light 3D model that captures the rugged beauty of maritime and warehouse lighting. This meticulously detailed STL file features a classic cage-protected dome design with…
Just put a usb a female cord through this bulkhead to pass wires through something
I designed this to fit CC 2" bulkheads. I printed at 100% infill but I'm sure it was overkill.
This 3D model is of a bulkhead plug with 1/8 BSPP (British Standard Parallel Pipe) threads. Ideal for sealing unused bulkhead ports, this plug offers a secure fit and reliable seal for various automotive and industrial applications. The…
Allows airflow on converted Vivarium Sterilite containers
Designed this for drybox use. it is a feedthrough that allows a 45 degree outlet. Threads for the "10mm" PC4-10M are NOT 10mm standard. (in fact they are BSPT 1/8in, tapered). the threads in this design are 10mm, .91 pitch non-tapered - a…
7.6-inch LOC Precision Avionics Bay Bulkhead. I design my parts to be replaceable as much as I can. So, nothing is glued on my AV bays. I use lock nuts and lock washers instead. Components I use: 4-40 threaded rods for the e-match…
Bulkhead‑Style Drain Fitting This is a compact bulkhead‑style drain fitting designed for clean, reliable pass‑through drainage in enclosures, tanks, coolers, or custom 3D‑printed projects. The fitting installs through a 1.5‑inch hole,…
