3063 modeli
The width is 110mm, although the printed version in the photo has been scaled in the slicer to 120mm. Thanks to the gentle slope, all remaining water flows easily into the sink. Any material, but the smaller the layer height, the better…
Wydruk około 1,64 €–2,00 € nettoWstępna wycena jednego wariantu
Keep your drains clean with this simple but super-effective 3D printable drain cleaner snake! Designed with fine hooks and a slim, flexible profile, it easily slides through most drain grates to grab hair and debris — no need to remove…
Wydruk około 0,20 €–0,24 € nettoWstępna wycena jednego wariantu
There are plenty of drain snake STLs out there, but this one has bite. The design allows larger teeth while keeping the snake small enough to slip into drains. Prints in less than 30 minutes and works well at 0.20mm layer height. Fun…
Wydruk około 0,26 €–0,32 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Use tree supports on build plate only + 3 walls, 5 bottom layers. The Washing Machine Drain Tray is a low-profile container designed to catch water when draining or cleaning your washing machine filter. With a height of only 25 mm , the…
Wydruk około 9,26 €–11,32 € nettoWstępna wycena jednego wariantu
A simple and effective drain cleaning tool for sinks, washbasins, showers, and similar drains. The flexible, barbed shape easily catches hair and other debris from places that are otherwise hard to reach, helping to clear partial clogs…
Wydruk około 0,17 €–0,21 € nettoWstępna wycena jednego wariantu
Bonsai Pot with Drip Tray, Drainage Mesh and Small Feet Looking for a modern, elegant bonsai pot? I was too — until I designed one myself! This set includes: A stylish bonsai pot with a drainage hole A matching drip tray to catch excess…
Wydruk około 1,79 €–2,19 € nettoWstępna wycena jednego wariantu
Should fit into a drain of around 50mm in diameter. The print is split into 2 parts in order to print cleanly without supports. I experimented with snap fit design, it takes some fiddling to put the two pieces together but it works better…
Wydruk około 0,75 €–0,91 € nettoWstępna wycena dla PETGMateriał u źródła: PET
drain pan to avoid the oil from filter messing up the engine front. the new version with an enlarged hose fitting an better coverage under filter's housing
Wydruk około 9,15 €–11,18 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I recently lost my Drain plug to my Yeti cooler. So I made a new one! This project includes one plug that you can use with no gasket. There is another plug too this one is to be used with a gasket, and I've also included a gasket to be…
Wydruk około 2,87 €–3,50 € nettoWstępna wycena dla PETGMateriał u źródła: PET
After reviewing a few comments, it became clear to me that the new jugs not only had a larger diameter screw-on, but the cup was larger too. My wife likes to use the original small cup and I am guilty of not thoroughly investigating the…
Wydruk około 5,66 €–6,92 € nettoWstępna wycena jednego wariantu
I recommend sticking a piece of gasket on the entrance edge. It is designed for old Bosch washing machine, but you can use it for any other machine for which it will be suitable. The neck of the container is 30 mm from the ground.…
Wydruk około 2,05 €–2,50 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Hi, this is just a remix of the magnificent work done by the original creator. I've just add some holes on the bottom of the pot to drain the excess of water (when the pot is in the exterior) I've printed in 0.28 layer Hight. No supports…
Wydruk około 2,57 €–3,14 € nettoWstępna wycena jednego wariantu
Adapter for emptying the water drain to the side without spilling water unter the mashine. Out it on the drain, then open the drain carefully. Ideally, place a bowl at the end ot the tube and remove the lid. Straight adapter see:
Wydruk około 3,31 €–4,04 € nettoWstępna wycena jednego wariantu
Ever needed to drain your washing machine because the pump got jammed? Yeah me too. Twice. In one month. Kids… Gotta love 'em! What I don't love is siphoning off a whole machine 1 liter at a time using buckets, so I decided to make this…
Wydruk około 0,23 €–0,28 € nettoWstępna wycena jednego wariantu
Update 1: I have designed a saucer for this pot. The pot can either be loosely placed in the saucer or you can put the corners of the base into the keyed edges of the saucer. When placed into the keyed edges, the footprint of the saucer…
Wydruk około 1,57 €–1,91 € nettoWstępna wycena jednego wariantu
The most recently purchased jugs of all® detergent have a larger diameter screw-on cap. My guess is they are standardizing with the rest of the industry as the new cap is the same size as OxiClean™ and several other bottles of various…
Wydruk około 4,52 €–5,52 € nettoWstępna wycena jednego wariantu
This is a remix of roosteralex82's drain hose holder for those of us who have to empty their portable washing machines into the tub (ask me about my Panda washer!). It juuuust fits a ~4" rim (~10.16cm) and, at 6.75in/171.4mm width, can be…
Wydruk około 5,04 €–6,16 € nettoWstępna wycena jednego wariantu
My wife has 2 styles of commercial tuna can drainers. But when the can company went to pull tab lids, the commercial models quit working as the diameter of the new lid was slightly smaller. I took some measurements and studied the…
Wydruk około 3,66 €–4,47 € nettoWstępna wycena jednego wariantu
I wanted to mount the reolink Argus3 camera with it's corresponding solar panel on a 100mm drain pipe. I printed in PETG. Let's see how lang that is going to last in the sun. Material for camera mount: 1 x 20mm M6 screw 1 x M6 hex nut 2 x…
Wydruk około 3,58 €–4,37 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a nut I designed for my kitchens sink drain, as the others I tried didnt fit well enough and it leaked. I will also upload the .SLDPRT file in case anyone needs to edit any of its dimensions, whether it is the inner diameter…
Wydruk około 3,78 €–4,62 € nettoWstępna wycena jednego wariantu
Why spend $20 on Hornady's Powder Measure Drain insert, when you can print one for 14¢? Printing Notes Contact area on the build plate is very small. Use a brim. A little bit of wet-sanding may be necessary.
Wydruk około 0,71 €–0,87 € nettoWstępna wycena jednego wariantu
The STL has a solid bottom. I added drainage using a 109.37 x 109.37 x 2.4mm cylinder modifier in prusaslicer with 40% gyroid infill and 0 top or bottom layers. You could also use a simple cylinder modifier if you prefer a single hole for…
Wydruk około 2,60 €–3,17 € nettoWstępna wycena jednego wariantu
With this tool, the oil change can finally be done without a big mess. Simply loosen the drain plug of the oil filter a little with a ratchet, then completely unscrew the screw with the printed special tool. The oil is completely…
Wydruk około 2,74 €–3,35 € nettoWstępna wycena jednego wariantu
Spare part/replacement for water drain plug: Kayak: Prijon T-Canyon (ca. 1995) Possibly also fitting for other Prijon Kayaks. Main Slicing parameters: - Slicing parameters used for Prusamet PETG - 0.2mm layer height - perimeters: 4 -…
Wydruk około 0,71 €–0,86 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Remake of sink drain sieve
Wydruk około 0,80 €–0,98 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Washing machine drain hose adapter to DIN 32, DIN 40, DIN 50, DIN 75 or DIN 110 standard sewage pipe. This rigid adapter allows you to connect a standard washing machine drain hose to a DIN32/40/50/75/110-compliant drain pipe, which are…
Wydruk około 0,98 €–1,20 € nettoWstępna wycena dla PETGMateriał u źródła: PET
My wife has 2 styles of commercial tuna can drainers. But when the can company went to pull tab lids, the commercial models quit working as the diameter of the new lid was slightly smaller. I took some measurements and studied the…
Wydruk około 2,26 €–2,77 € nettoWstępna wycena jednego wariantu
A modification of jmbinette's ECM Synchronika Drain Pan upgrade ( link ), which is itself a major upgrade of the drain pan provided by ECM. This variation is sized slightly smaller in the corners to make it printable on a Prusa Mini, and…
Wydruk około 17,71 €–21,65 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I created these Plant Pot Spacer Rings to tackle a common problem: stagnant moisture building up at the roots of plants in flower pots. After noticing some of my favourite houseplants struggling with soggy soil, I designed these rings to…
Wydruk około 2,46 €–3,01 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Introducing the 3D-printable Berry and Fruit Washer with Drainer , a two-part kitchen essential designed to simplify your fruit washing routine . The innovative design includes a base where water collects and an upper compartment with…
Wydruk około 4,53 €–5,54 € nettoWstępna wycena jednego wariantu
My second approach for an easy to use and rarely to clean strainer for floor level shower drains. This time I replaced the original tube ("TECE Tauchrohr" see pictures) by an own designed one.The new tube is for the siphon-function in…
Wydruk około 2,02 €–2,47 € nettoWstępna wycena jednego wariantu
Motivation Before the rain season starts, I was urged to create this model for covering a broken (already missing) drain strainer cover, so water from the rain can go into the sewer pipes but not get full of leaves or other material that…
Wydruk około 4,32 €–5,28 € nettoWstępna wycena dla PETGMateriał u źródła: PET
My rain barrel I paid for (dumb move by the way… got a massive cistern for $30 that was used for soap that works a billion times better) had a ½" NPT connection on the top and bottom. Not sure why they'd do that, since so few of anything…
Wydruk około 2,39 €–2,92 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The sift is intended for bathtub drains where the plug has an 8-mm center shaft. The model has a 3-mm inner screw, so that you can strengthen and weight the printed shaft with a 3-mm metric screw.
Wydruk około 1,10 €–1,35 € nettoWstępna wycena dla PETGMateriał u źródła: PET
If you found that the strainer doesn't fit completely with the drain (too small), please print along with the sleeve and put it on the outside of the strainer for better fit. They were successfully printed with PLA. I recommend not…
Wydruk około 1,22 €–1,50 € nettoWstępna wycena jednego wariantu
I was sick of having cutlery soaking in water so I made this riser. It's meant to work with ORDNING Stainless Steel Cutlery Stand and the EKIPERA plate. It prevents drying cutlery to come into contact with excess drain water. Edit feb…
Wydruk około 2,05 €–2,50 € nettoWstępna wycena jednego wariantu
Large support for perfect stability without adding extra weight. Height is adjustable using pre-drilled holes with m4 screws. For North Americans, the sliding foot can be replaced by a 2 "x2" wooden one, cut to your requirements. The…
Wydruk około 0,32 €–0,39 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The JOSEPH JOSEPH dish drainer has a water drainage slide that is unfortunately too short to reach the sink in the house. The faucet's position does not allow the dish drainer to channel water into the sink. I designed a 3d-printed…
Wydruk około 2,08 €–2,54 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Model Odor trap cover for a drain pipe with a 40 mm inner diameter. Print Material PETG or PLA Nozzle 0.4 mm, layer height 0.2 mm 4 bottom layers, 3 top layers Scarf joins as needed Bottom infill pattern: Concentric (simply looks better)…
Wydruk około 0,80 €–0,98 € nettoWstępna wycena dla PETGMateriał u źródła: PET
ENGLISH Bathroom organizer/shelf for shower gel, razor, soap, washcloth, hairbrush and much more. The sloping base plate allows the water to drain to the front. Water no longer accumulates under objects that are on an elevation. It stays…
Wydruk około 6,70 €–8,19 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Combined 2 designs in one. Used this one also https://www.printables.com/model/879721-bog-planter-with-moat
Wydruk około 9,55 €–11,67 € nettoWstępna wycena jednego wariantu
This is a drain cover. Part of the Impey wet room drain system. It is the top cover. I used an Ender 3 S1 Pro to print this. The model is undersized by 0.3mm and printed on PLA+ with 50% infill. It locked in to place, and no issues so…
Wydruk około 5,14 €–6,28 € nettoWstępna wycena jednego wariantu
I designed this because any other designs that I found on Printables had holes too small and did not allow water to pass through and so ended up blocking too easily with very small amounts of debris.
Wydruk około 1,29 €–1,58 € nettoWstępna wycena dla PETGMateriał u źródła: PET
See this post : My next approach to handling the soap bar problem: a floating soap dish with a perforated bottom so drying and draining from below can happen. My journey so far: 1. standard soap dish. It's a slurry mess. 2. fancy soap…
Wydruk około 2,37 €–2,89 € nettoWstępna wycena jednego wariantu
I was tired of cleaning the trap in a sink with no drain plug. All sorts of things get dropped in by accident, not to mention the multitude of hairs. This plug went through 3 revisions to allow decent drainage, while keeping the majority…
Wydruk około 1,47 €–1,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is my simple design of a short drain that can be printed with PETG and without any supports. The idea is to glue or screw this drain on the bottom of a container, pot or pipe to direct the water flow into the desired direction. How…
Wydruk około 1,71 €–2,09 € nettoWstępna wycena jednego wariantu
Výplň 20%, bez podpěr a límce. Materiál PETG
Wydruk około 0,76 €–0,93 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This tool helps you open your drain grate, whether it’s in the shower, outside in the courtyard or for point-type drains. I’ve created two different versions: a single-sided one for smaller holes in channel-shaped shower drains and a…
Wydruk około 0,10 €–0,12 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I had issues with the drain plug on this boat falling out while rowing. Instead of replacing the old stopper with a new one, I decided to practice my design skills by creating this clip. This is for an older Maas Aero. I checked, and…
Wydruk około 0,58 €–0,71 € nettoWstępna wycena jednego wariantu
Works in PETG but better in PA or TPU 95A
Wydruk około 1,34 €–1,64 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Over the years some of the spacers of my ACO showerdrain got lost. The spacers keep the top cover in the middle of the drain and leave enough space for the water to flow below. Best to print it with the two cylinders facing up.
Wydruk około 0,38 €–0,46 € nettoWstępna wycena jednego wariantu
(2.0) Update: New versions to counteract the “benchy hull line” If you're not sure what I mean by “benchy hull line”, read this article. I have rounded out the bottom interior of the planter to counteract the slight layer shift our…
🚨 UPDATE: Check out the improved V2 here: BOM: Printed with ROSA3D High Speed PLA Gray Say goodbye to soggy, smelly sponges. This drip tray features a functional wave pattern on the bottom that lifts your sponge (or soap bar) slightly up,…
Versatile drain cleaning tool available in three lengths—15cm, 20cm, and 25cm—designed to effectively unclog and remove hair and stubborn debris from (drain) pipes. Works with most filament types, provided they aren’t overly flexible or…
This was inspired by the original Laundry Detergent Cup Drain and modeled from scratch in Fusion 360. As is, it fits the new Tide bottle, but the model is fully parametric and therefore can be adjusted to fit other detergent brands. It…
Update: I have uploaded a revised version of this model that decreases the angle on the curve on the bottom of the planter to improve print quality on the overhang. This revision also improves the tolerances on the tray so the planter…
Nothing special, another barbed drain cleaner i designed one day i needed one and didn't want to use one from the internet Should be able to be scaled in slicer in case you need it longer, thicker/thinner or wider I recommend printing it…
Soap bar holder that drains on its own
This bucket is designed to catch dirty water when cleaning the pump filter of LG washing machines. It was specifically developed for the LG F14WD96TH2, but will likely fit other LG models with a similar pump filter position and height.…
This 3D-printable stand is designed to hold sponges, washcloths, and soap, ensuring that excess water drains directly into the sink instead of pooling on your countertop. Say goodbye to soggy sponges and messy countertops with this…
This Aztec Pattern Planter is the perfect size for any small to medium cacti, succulent, or other houseplant. The design includes a series of drainage holes, as well as an optional, custom-fitted drip tray. The default size of the planter…
Print-in-place articulated Scrub Daddy sink holder designed for easy, support-free FDM printing. Prints in about 2.5 hours and uses roughly 45 grams of filament . Articulated legs hang over the sink edge, arms support the sponge, and a…
🎯 Recommended Print Settings For Best Results Print this design with a standard 0.4mm nozzle at 0.24mm layer height for that sweet spot between speed and detail. We're keeping it lightweight with just 8-15% infill, which gives plenty of…
Update: I have now uploaded slightly improved versions of the planter and tray models. The tray should now have a snug fit with the planter, keeping it from sliding around and getting off-center. The pictured print was done in matte gray…
A Soapdish tray for the kitchen or bathroom. Self-draining, large enough to hold soap bottle & sponge. Small version to hold a sponge or soap bar. Filename: 1 x Kitchen_Bath_Soap_Tray_Large_v1.stl Large enough to hold soap bottle & sponge…
BOM: Printed with ROSA3D Starter PLA Black Say goodbye to soggy, smelly sponges. This upgraded drip tray features a functional wave pattern that lifts your sponge (or soap bar) up, allowing air to circulate underneath and water to flow…
Aspire Planter: The Aspire Planter is the perfect size for small to medium sized houseplants, succulents, or cacti. The planter features built-in drainage holes and a drip tray that is perfectly contoured to the bottom of the planter,…
Thanks to MrTheKod for the re-remix! The original re-remix file had some internal geometry issues and needed to be repaired before it could be printable. I made some changes to make it print more easily, faster, and with less material and…
A soap/sponge tray which allow for airflow and fast drying.
Fits 70mm drains, allows for good flow even when partially blocked. Should be printed with heat resistant filaments if its going to be exposed to boiling water, I found that PETG and ASA will warp, while PC is able to resist warping with…
I just made a very slight modification to an already fantastic design by davwilso. The new cup that Tide supplies has a larger diameter so it no longer fit in the original design. I I just added a wider lip at the top to contain the new…
This drain snake was created to have extra long barbs to help grab all that stubborn hair that can get caught in the drain. PLEASE NOTE: you need to have a drain opening that is greater than 4x12mm in order for this snake to fit in your…
With everyone staying at home your drains might be getting clogged more quickly. You can't call anyone to take care of it and you can't go out to buy a drain cleaning tool or chemicals, so why not print your own!? This 8.5" drain snake…
Update: v3 Release All three parts of the planter have been updated for this release. The main change is to the drainage pot. Now, the interior overhang is much less steep, enabling printing without supports ! The bottom interior surface…
"There are so many spiral cups and planters on this website, why would you design another one?" Well… first of all, hello. I am glad you asked. Like, I am sure, so many other designers, I frequently see models online and think “I like…
This design stores the laundry detergent cup for Tide and Gain brand liquid laundry detergent containers and drains excess leftover soap back into the container. Single print design (Print in Place) Fits North American Tide and Gain 4.43L…
A collection of kitchen and bathroom drain strainers, stoppers, and drain pads. Useful for kitchen sinks, bathroom sinks, utility sinks, bathtubs, and probably more! Before printing, please review the list of models and their respective…
Practical sponge box with a drainage groove to keep your sponge dry and hygienic. Compact design saves space at the sink and fits any kitchen.
A small sponge drain rack, sutable for two sponges and two mini brushes. Supports are required when printing
I designed and 3D printed this minimalist soap dish to solve a common problem — soggy soap! It features a built-in drain channel that allows water to run off easily, keeping your soap dry and lasting longer. The open design promotes…
Maceta cuadrada para plantas pequeñas, con drenaje de agua incluido. Especificaciones: Las macetas tienen 50mm de altura. El grosor de las paredes de la macetas son 2mm. los agujeros de drenaje de agua son de 4mm de diámetro con el…
Summary Drain spout sized to 65 mm that fits a Samsung washing machine (my model number: WW70K44205W/EG). The Reason to Publish I searched across all major platforms and found various models that could work for my washing machine, but all…
Default size is checked and tested. It's safe if you want to print size bigger, but smaller please check the wall thickness before printing. Instruction video:
Resin vat drainer for anycubic photon mono Summary Resin vat drainer Print Settings Printer: Voron 2.4 Rafts: No Supports: No Filament brand: PolyMaker Filament color: Black Filament material: PETG Notes: Resin vat drainer
Remix of glsf91 model https://www.printables.com/model/138644-solar-panel-water-draining-clip-for-flat-roof This model fits 35-40 mm panels, 8 to 12 mm lip. Measure if this fits. Should fit DEMGC 485, 490, 495 W monocrystalline panels.…
Chikorita pot, in two versions: with or without drainage hole. Modified to be a flower pot from a model downloaded from the internet. Macetero de Chikorita, en dos versiones: con o sin agujero de drenaje. Modificado para ser macetero a…
My old drain hose holder that came with my washer was too narrow to actually hang on my sink. I designed this one to fit a countertop/sink combo that's up to 90mm wide. This can accommodate a 30mm hose, so it's wide enough to fit a common…
Give your bathroom sink a clean and modern look with this practical soap dish for standard soap bars. The raised radial ribs keep the soap above collected water and allow air to circulate underneath, helping the soap dry more quickly…
Solar module drain clip for 30mm panels. Wonderfull in flat roofs (<30º) It drains the panel completely avoiding accumulation of dust. Insert it in the lowest panel side. Solar module drain clip for 30mm panels Tested with AE Solar panels…
This is an MMU painted version of patrickart's bulbasaur model with a hole carved out in the back so that it can be used as a plant potter. I carved a tube through its butt as a drainage hole so that it's a proper pot. Very anatomically…
A versatile sink drain strainer designed for sinks with an Ø82, Ø86, or now Ø90mm diameter, featuring an integrated plug. The press-fit design accommodates a drain plug stem that fits most modern drains (Ø8mm) and includes a gasket for a…
Creator:muskokaresearch https://www.thingiverse.com/thing:5352444
Fed up with getting the mop out every time you clean the washing machine filter? I designed and 3D-printed a small, cust. It is made in PLA in two interlocking parts. Samsung Eco Bubble WF70F5E0W4W
If you have solar panels on a flat roof and the panels are less then 15 degrees mounted, some water will stay in the lower edge of the panel. After some time your panel become dirty in the lower part and it reduces photovoltaic panel…
ENG: This pot can be used both as a self watering pot and as a classic pot with draining holes but with a modern design cover pot, since the bottom of the internal pot doesn't touch the one of the cover and allows the water to drain,…
My sister asked me to make her a soap holder like the one by Kitsch but with two slots instead of three like their product, and seeing as it was a pretty simple form, I threw this model together and printed it for her. Turned out quite…
UPDATED 11th March 2020: Added straight-through Y pattern, optional flow arrows. Having a european-built caravan in Australia, I found it very difficult to get the 28mm diameter sink and drain pipe plumbing these are fitted with. I tried…
Designed to print on its back without supports. 2026-09-21 : Added model with inside width 216,6, (first model have 146,6)
A flexible Sink Caddy for your indoor or outdoor sink. Dimensions (with lower cup): L:180mm; W:92mm; H:135mm Features Store your soap; sponges and brushes in a flexible configuration. Divider allows for 1/2 split or 1/3-2/3 split. More if…
Wall mounted planter - with insert drainer. Easy to take it out and water the plant. Note: it is easier to print the insert with tree supports. i might update it so u dont have to do that.
