140 modeli
NOTE! You may need to scale the model up about 1-2%, I designed it with very tight tolerances. New v2 Version! Now includes a larger cut face, and a hole where you can put an m5 bolt thru along with a t-nut to clamp the guide onto the…
This is a cable channel for the Enderwire conversion. It's mounted with M3x8 screws to the frame. You can use the zip tie points to hold some cables down. Feel free to break off some of the studs in the center if they are in your way :)…
I didn't want to buy an original Keybak because it's expensive to get in EU. Planning to switch to motor brake PCB anyway. This fits cheap door pullers from aliexpress. I bought this one:…
I didn't like the square model of the printable TPU Foot for Switchwire, so I made a round one. Print with TPU and 10 to 20% infill (depending on how hard your TPU is).
Small buck converter mount meant for the Voron switchwire/enderwire
Brenden D'Paula made an excellent mod to use the Bambu A1 silicone brush. I was looking to make one from scratch but decided to remix his instead as it was designed very elegantly. I remodeled it slightly so that it will work with the…
Darkdog supplied an stl to mount the nevermore v4 at the front of an ender 3 switchwire conversion, I have mixed this with the original front panel mount to create these mounts, left or right or both. I have revised the mounts with…
Depressor Mount Enderwire Switchwire for ERCF Filametrix https://github.com/sorted01/Filametrix settings filametrix ( _MMU_CUT_TIP.cfg ) variable_pin_loc_x: 23 variable_pin_loc_y: 180 variable_pin_park_x_dist: 6.0…
BTT Pi Mount for 2020 Extrusions / Enderwire as it has a slightly different hole pattern than the Raspberry Pi. It is also moved away from the extrusion to allow room for 90 degree connectors.
The Enderwire non-pro 's Y axis is quite wobbly due to the single MGN12h rail in the middle of the whole assembly. I searched for a solution to use two MGN12h rails while still using most of the original conversion files, so i came up…
This addresses the issue brought up in the DaRk_dOg's Ender SW repo: https://github.com/boubounokefalos/Ender_SW/issues/39 The cutouts were taken from the original Ender 3 bracket. I made sure the original design aesthetics remained…
Enderwire Stock Power Inlet modded to fit the parts of my Ender 3 v2. For Power Inlet Huaconn HC-99-F1 and Rocker Switch Huaconn HS9-C2 from stock Ender 3 v2
This is a Remix of Voron Switchwire BTT TFT35 SPI V2.1 Housing made by Ken226
you need 2x M5x10 Button Head Screw 2x M5 T-nut 4x M2x10 Self tapping screws you can use old salvaged screws for self tapping.
This is a nevermore V6 micro mount for your enderwire conversion it only uses 1x m3x16 SHCS to hold the nevermore in the mount
Although there are many models of Nozzle Wiper for the Ender 3, I've not been able to find one that fitted my Enderwire Conversion. My model uses the Silicone Brushes from the Bambu Lab A1 as I'm not a fan of Brass Brushes. There's a…
This mount allows you to mount a 15mm(OD)x10mm(ID) cable grommet to a 4020/4040 extrusion. I used it together with my umbilical cable mount for the Voron Stealthburner…
Its a trident style insert for your enderwire build to pretty up your skirts press fit it into your front extensions
Update 24/02/26: Corrected an issue with the bearing retainer threading and file names. This is a remix of nhchiu 's fantastic Switchwire Double Shear Motor Mounts redesigned to work with the Enderwire conversion. Other than the supplied…
This is a remix of the alternative keybak for Voron Switchwire or Ender 3 to Switchwire conversion. With this mod you can use the Voron standard heat inserts (M3x5x4) Cheap door puller as keybak: → https://www.aliexpress.com/item/100500…
An X carriage adapter for the Sprite Pro Extruder that allows the use of a linear rail and the belt driven Core XZ motion system of the Voron Switchwire. I printed with ABS+ using Voron's recommended settings found in the beginning of all…
Original Y endstop by @DaRK_dOg still has its uses pending the brand of electronic endstop switch you use.
Its a prototype for now, I printed this from Nobufil ABSx for now with 5 top- and bottomlayers and 5 walls with30% cubic infill in 0.2mm layerheight. ABS isnt the ideal material for this, i would recomend something like PC or Nylon due to…
Mount for BTT Pi for enderwire Printed with standard voron settings. Uses M2.5 screws
The mount fits into the right z_bearing block, but you will need longer M5 screws (+1cm). It allows to use all PUG models. You will need to print the modified part with supports. Otherwise print with Voron settings.
This allows the use of the EVA cable mount for your umbilical cable strain on the Stealthburner.
I needed USB and LAN on the back of the printer, so I remixed the middle rear skirt for keystone inserts
I am currently working on an Ender 3 Pro Switchwire Conversion, using the Enderwire design from boubounokefalos. He already added the 3D printable version of the top cover, but not the lower cover. It uses the standard M3 threaded heat…
I remixed the SKR Mini E3 V3 mount that comes with the boubounokefalos conversion to fit a Manta E3 EZ board
I Printed it in PETG and fits great! Uses 4-M3x6 to mount buck converter to board, and 2-M3x8 with T-Slot Nuts to mount into extrusion.
BTT Manta M5P mount for Enderwire. (5) M5 x 10 screws w/ (5) M5 Spring nuts needed to mount to frame, (4) M3 heat inserts m3x4x5, and (4) M3 x 8mm hex screws.
Purchased the Fysetc DSI display as it was much cheaper than the BTT one but found that it's a much slimmer display with the ribbon cable in the middle instead. Remixed to make it work for the Fysetc 5" DSI display. Update : Added a…
This is a Fan Holder 30x30 for the Raspberry Pi. You can use it alone or with the Fizzy tech Pi Holder for the Enderwire. See Here: https://www.printables.com/de/model/558357-ft-ems-mounts-repository Youu need : 30x30 Fan 4xM3 Heat…
Ender 3 Pro/V2 to Switchwire Conversion ver.2 y endstop mount is correct in this model and a switch can be installed.
I was not happy with the way the stock Enderwire's (nonPRO) enclosure panels are mounted. VHB tape is not a good way to make the whole assembly rigid. Therefore I created this mod to fully implement a frame out of 2020 extrusions while…
I found that the gantry would always tilt in one direction or another if there was a minor crash or if I moved the gantry by hand with a tad bit too much force on one side. I found that the main cause was because of the flat faced bearing…
ENDERWIRE nonPRO - Printable deckplate Basically this is based on the original Ender3 to Enderwire nonpro deckplate, but… cutted 3 pieces for able to printing in smaller printers make clearance for easier placement on a builded machine…
BigTreeTech HDMI5 1.2 mount for the Switchwire or Enderwire.
This is non pro version of Enderwire EMS. There is no space for rear y motor mount as well as moved the mounting point for main EMS under the Y extrusion.
I revamped the model to remount the Ender 3 12864 LCD screen to the Voron Switchwire grills. This allows to keep your start up costs low.
Front grill mount for the Ender 3 switchwire mod by DaRk_dOg, adding HartK tft mount
Modified cable channel to line up with the wider frame cutout on the Ender3 V2.
Front grill mount for the Ender 3 switchwire mod by DaRk_dOg, adding HartK tft mount
Added second body to the grill models in order to follow eddietheengineer's method for configuring an accent mesh in the slicer. Here is the reference video. FYI There seems to be an issue with the original models where Prusa Slicer will…
This mod for the enderwire by Ultrawaffles. It adds a second stepper motor to the Y axis to increase acceleration and speed. This mod requires a motherboard with a free stepper driver. Hardware: 3x M5x8 3x 2020 M5 Tnut 4x M3x25 1x Nema 17…
I wanted to have 2x 6020 fans for the underside so I created these remixes from the Ender Switchwire github.
move the inlet to middle
It's not perfect, but will get the job done. You can also find this model in OnShape for making any adjustments you may think it needs.
The whole thing is very wobbly. “HDMI5 base” requires support. BOM: 6x16 M3 2x M3 heatinsert Cable adapters I used: USB C: https://de.aliexpress.com/item/1005004456693859.html HDMI: https://de.aliexpress.com/item/1005005750965229.html…
We're fine-tuning Trinity for the Ender 3 and welcome your input to shape its future. While initially for the Ender 3, we're open to expanding compatibility based on demand. Our dedicated team constantly improves Trinity to ensure it's…
I wanted to print the Raspberry Pi holder from here , but my Raspberry Pi's heatsink case uses M2.5 bolts instead of M2, and I had some M4 T nuts laying around instead of M5. I edited this in Fusion 360 using the original Ender_SW CAD files
i will add print-part-pictures soon
This is an remix from Fizzytech Enderwire Mod, I Made a Stronger Relase for the front Rear for it. See here : https://www.printables.com/de/model/588776-ft-ems
Enderwire Bed Model to use with any Slicer. It's meant to be used with 220x220 bed size. Extracted directly from https://github.com/boubounokefalos/Ender_SW Fusion model
This is a modified version of the 60mm fan mount that Steve supplied for the v1 enderwire conversion, I have adapted to to suit the v2 conversion.
For materials, instructions, and for the other final printed part, visit @LivingroomWorkbench's original model: https://www.printables.com/model/560244-ender-switchwire-bed-cable-extension
This is the Splittet Rear Frame of the Original Fizzy Tech Rear , you can print it , on lower Beds.
A 3D Printed mount for attaching a BIQU HERMIT CRAB tool-changer to an MGN12H linear rail. This mount is designed for an Ender 3 with a Voron Switchwire conversion (Ender-wire) but may also function on a regular Switchwire, although I…
INTRODUCTION Since the Raspberry Pi seems to be the go to compute module its only natural for us to support the Raspberry Pi Camera module. This is a 4 piece mount that attaches to the right front panel bracket that attaches the side…
I redid the model to add space to 5mm and suit the original enderwire model j'ai refait le model pour ajouter de l'espace a 5mm et convenir au model original enderwire
Voron Enderwire Manta M5P for rear middle and right grill with pass through for RJ45, USB, etc.
This remix are made for a regular ender 3 switchwire conversion. https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/Gizzle/ender-3_(pro)_switchwire
Printing Recommendations: Standard Voron print settings Use Brim or Brim Ears to avoid sharp corners from lifting The parts are oriented the right way Included .step file can be used to make changes if needed Required Hardware: Nevermore…
Hex pattern inserts for Switchwire front skirts.
I wanted to run a few Bento Minis in my Enderwire project. I used the front panel brackets from the DaRk_dOg / boubounokefalos Enderwire . I am not sure if it works with the official Switchwire. This connects using the M5 and M3 front…
Description in WIP! Servo Model: GuoHua A0090 Umbilical Mod for Stealthburner (using this you will not lose Z height): https://github.com/kejar31/VoronMods/tree/main/CB-C2
I am currently working on an Ender 3 Pro Switchwire Conversion, using the Enderwire design from boubounokefalos. I love his design and the VORON design idea, but I just did not get around to changing the fan mount because I love how it…
See description from Original creator: https://www.printables.com/model/618488-stop-it-z-endstop-chamber-thermistor-mount-for-vor
couldn't get tinkerman's mount to do what i needed without drastic modification, but was inspired
Reacently I bought CNC Voron Tap and after unboxing it I realized that belts are mounted in a diffrent way than I thought. So I creadted adapter for it to fit into my enderwire.
Cartographer mount for Enderwire with Dragon Burner. The mount can be used with standard edition, but you will have to use the belt clamps with cut as otherwise, the socket won't fit. Thanks to @PiotrChaos, it seems the mount can also be…
Made for “USB camera modules” you find on Aliexpress with a 29mm hole pattern. There are a lot! I assemble and configure everything in this stream:
Here are the Mantis V2 Complete Printhead Mount for the Enderwire/Switchwire. The diffrence between the Original is: You can Mount the EBB36 with Can holder Beacon Mount Included Alternative Duct Mount to stabilize it better. The…
Makes the tensioner work with the thomasfjen v1 ender 3 to switchwire conversion.
Seffyr adapted the Switchwire Double Shear Motor Mount for the Enderwire conversion, but originally only for the X and Z motor mounts. To make it work for the Y axis, I needed a more compact housing that sits slightly closer to the belt.…
You can add Keystones to the Part and Micro SD slots. Keystone USB: https://www.amazon.de/dp/B07Z94HYFG?ref=ppx_yo2ov_dt_b_product_details&th=1 Keystone LAN: https://www.amazon.de/dp/B07L9VMFK7?psc=1&ref=ppx_yo2ov_dt_b_product_details…
This is for the right side only, mirror it on your slicer to have the left side.
I promised to cad this up ages ago and as soon as I actually started rebuilding my enderwire I actually did it. Inspired by RockAndRoll for the 2.4, you can tip an open or enclosed Enderwire on its side and and it will be stable. Yes my…
Tired of adjusting belt tension by moving the motor? This solves it. This is a simple and compact belt tensioner designed for Voron Switchwire and Enderwire (XZ axes) . No need to loosen motor screws during adjustment The mechanism works…
Grill dla kobra neo, zremiksowany z modelu dla Enderwire, montaż wymaga nagwintowania otworów w szynie Vslot.
I took the original PG7 - 2 file and created a version for two hole cable chain and had the PG7 thread be at a 45 degree angle so the umbilical would not hit the top of the enclosure when printing the full print height.
The stock creality 42-34 stepper are shorter compared to the BOM stepper. This results in a small gap between stepper motor and enclosure - not only ugly but also bad for chamber temperature. Modified the original wide clip from…
Remixed BOM MGN12h rail bed parts to support a MGN15h option to add stability for your Ender 3 non-pro to Switchwire conversion.
Decided to try and get the Enderwire to print as fast or faster than the Bambu bedslingers. This is my take on the 9mm belt mod for the enderwire which uses a double shear motor mount to support much higher belt tensions, toothed idler…
This is a mount for the M4P in the Switchwire. It's REALLY tight. You need 90º USB adapters to use the USB ports on the M4P, but this blocks the Ethernet port. Installation: I also added a mount for an 8010 fan to cool the steppers, this…
Compatible with enclosure as it acts as both camera holder and panel holder. To mount it, I used an M5X20 screw with an attached nut to make it like an M5X18.
I double-sided taped it to the top panel and used the wire organizer to run USB cord. Mount Uses one M3x30mm bolt with M3 Nut
a mount for the hdmi 5 by btt for the switchwire/enderwire
Building an Enderwire, I have found out that the screen cover wasn't quite suitable for the MKS mini12864 v3 I own. It has different PCB dimensions, a beeper on the back and slightly different components layout versus the BTT (?)…
This combines the top door latch with a C270 Mount Uses one M3 M3x30mm bolt with M3 Nut
This is a Nevermore Micro V6 mount for Fizzytech's variation of the Enderwire. Should work with standard Enderwire builds, the only difference is that the FT Enderwire has holes for the enclosure panels (Fizzytech's enderwire doesn't use…
-use m3x6 or m3x8 screw and t-nuts -its for 25mm gap
The original creator made some awesome revisions to allow for a much more rigid means of mounting the gantry bearing blocks onto V Slot extrusions. I run an umbilical setup on my enderwire, meaning I do not need the cable chain mount on…
Its the same as Ken226's model only difference is it can fit the Y-Idler part of Enderwire using a press fit m3 nut and a short m3 screw. I wanted to use his model and this helped me thought maybe I would upload in case anyone else needed…
Mount made to put a BTT M4P into an Enderwire conversion.
The summary pretty much says it all. I wanted to incorporate my Knomi into my Enderwire seamlessly and could not find a skirt using the v1 hardware. Unfortunately I think I killed the screen on my device before I installed it in the…
Modified front grills for either boubounokefalos (DaRk_dOg) or EzrielDreamurr Ender Switchwire conversions. This allows the use of a 60mm fan on the front, just like the 60mm fan used in the rear grill by default. These can be used on…
Had a couple Disco on a Stick LEDs laying around from a previous Voron 2.4 300mm build and found that it would fit perfectly in an Enderwire. This mount is designed specifically for Fizzystech's enderwire enclosure with holes that align…
A spool holder alternative for the Enderwire which reuses the stock Ender spool holder tube. I designed this variant because I have a roller bearing spool holder and wanted to reuse it on my Enderwire, but it will work with the…
