345 modeli
This is a repair clip for your broken Ethernetcable. You can easy print it. The clip makes it possible that the cable does not always slip out so easily when the clip is broken off at the top. To print: you can use PLA too Use supports
Wydruk około 0,25 €–0,31 € nettoWstępna wycena dla PETGMateriał u źródła: PET
An anti-tamper lock for RJ45 Ethernet Cable connectors. I have cleaned up the original, made the hole smaller and cut off two of the corners to make it fit in more scenarios
Wydruk około 0,16 €–0,19 € nettoWstępna wycena jednego wariantu
Hello! Forgot to add the boot/cap/cover to your RJ-45 cable and you crimped it already? been there, done that. Hope this helps. This is a work in progress (W.I.P.) as it's not the easiest print using FDM printers, yet. Update 2022-09-07…
Wydruk około 0,42 €–0,51 € nettoWstępna wycena jednego wariantu
Dust cap for network jacks with easy pull tab
Wydruk około 4,67 €–5,71 € nettoWstępna wycena jednego wariantu
Note: Please see my remix https://www.prusaprinters.org/prints/155787-prusabox-enclosure-enlarged-buck-converter-box-wit for an enlarged version of this same design to more easily fit all the wires with the relay in the lid. This is a…
Wydruk około 5,30 €–6,48 € nettoWstępna wycena dla PETGMateriał u źródła: PET
RJ45 Extension Holder for the Prusa Mini Enclosure, which can be screwed to the back of the enclosure. This makes the enclosure more transportfriendly because now you have an easy to reach connection for your LAN cable. All you need is a…
Wydruk około 0,59 €–0,72 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I remixed this to fit a GMRS extension RJ45 (CAT5) cable that's routed from the arm rest through the panel...I resized this to fit the smaller port in the bottom, and added two cutouts: pass through for CAT5 Cable for install larger hole…
Wydruk około 0,29 €–0,35 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This clip was design to fix/repair/secure the broken or loose tab of a RJ45 Ethernet connector and avoid crimping. Designed to prevent from moving, wiggling, falling from the connector and easy to install. UPDATE 27/01/2021 Added the 3…
Ethernet (RJ45) Port Dust Cover cap with grip for easy removal. Just added: New slimmer/narrow model for switches with closely spaced ports. Check out all other port covers: USB-A port cover -…
These are replacement clips to fix broken ethernet cable clips. The clips attach to the Ethernet cable and replace the broken clip so that the cable stays locked into an Ethernet port. EDIT - For some reason Simplify3d doesn't like this…
This design is a unique combination of the short designs, where the latch is fixed at the connector and the longer designs, where the clip is mounted to the cable behind the collet. The design considers the exact dimensions of the collet…
Ethernet cable fix which prints WITHOUT SUPPORTS. The layer line orientation aids in keeping the cable in the port. Print settings: layer height 0.2mm 3 thick walls Infill: Does not matter since the piece is too small to even have infill…
Designed to protect the RJ45 sockets of my small Ubiquiti Unifi Flex Mini Switch that sits upright on my desk. Can be used on any other RJ45 sockets… Recomended Material : PLA Nozzle Diameter : 0.4mm Layer Height : 0.2mm Support : YES…
This print is intended to help you load wires into the RJ45 easy plugs. Just put it in, one by one and slide it a little and you are good to go. Loader should fit int the plug and is supposed to stay inside. Using 1 line model is…
Cable Organizer / Cable Clip - Clip RJ45 - USB Ø3mm USB Ø4mm - Ø6.5mm - Ø7mm - Ø8mm - Ø9mm - Ø10mm 12/01/2025 added: CPM_USB CPM_Ø7mm CPM_Ø9mm 19/01/2025 added: CPM_Rj45 Long Patch CPM_Ø6.5mm 10/03/2025 added: CPM_USB Ø3mm CPM_USB Ø4mm…
This is a tool to assist in the migration of a Cisco or Meraki switch with a new Cisco or Meraki Switch. You would move the existing cables from the old switch to the tool allowing you to keep the cables in the same port locations. Then…
Summary Slim RJ45 Ethernet Cap / Coupler that will save your ethernet cables and especially the plastic retaining tabs on your ethernet cables in bags cluttered with other cables. There is one open ended file to customize to your…
Fits Leviton and other Cat5/6 (RJ45) Brand Keystone Jacks
An ethernet RJ45 repair clip with a working snap lock that locks the plug in the socket. Prints without supports added from the slicer thus it prints quicker and and uses less material. NOTE: Needs to be printed with 3 perimeters (3…
Optimized overhangs (removed 90 deg. angles) 1x, 2x2, 3x3, 4x4, 5x5 and 10x10 files.
Quick fix for RJ45 plugs whose little clip broke off. Because there are so many variations of RJ45 plugs and every one needs a different version of this model, I uploaded a .STEP file and an editable Fusion 360 file where all the…
8/18/2024: Updated pictures to match the updated stl and CAD files. Printing with organic supports and no top interface layer provides the best results I have found. 8/9/2024: Printing the fillet edges has been particular difficult to get…
I have another advanced version of this that has various sizes (30, 32, 35, and 40 to ensure your adapter will fit). https://www.printables.com/model/886799-rj45-ethernet-cable-rj45-keystone-mount I could not find something to protect the…
Made a shield to fix the illumination from my wifi accesspoint led light. Tape didn't cover the light enough. Using a printed piece makes it removeable again. Best to print with some more infill and darker color to block the light.
This is an add in RJ45 keystone connector for drop-in use inside an enclosure. It should however be printed at a slant so that the the overhangs will print properly and then no supports are required on the inside of the connector. In your…
This is a problem that has plagued me for over 20 years. I was so pleased to see several 3D printed solutions. Unfortunately the original design by guss67 typically requires supports. To combat this there are designs that print in the…
I need a tool to help me replace network switches and ensure that all cables are connected to the correct port. This allows you to securely clamp the network cables and go back 1 to 1 after replacement. I have created a 16 and 24 port…
Remixed from dual version: https://www.thingiverse.com/thing:4273415 IG post: https://www.instagram.com/p/CHvzaRlB7cl/
I created this parametric model from blueprints, and I've been using it for a couple of years without issue. See the photos for the 3 sizes I use the most (1, 3 and 4). Fusion 360 link: https://a360.co/4cxypP1 Printing: without supports…
Tips: Set PLA temperature to 220℃, even 230℃. Consider using PETG - it's better suited for flexible joints. Try 0.12 mm layer height Scarf joint is required to prevent flexible tab breakage Print on the side with supports to achieve…
Aufputz Patchpanel für 4 mal Keystone RJ45. Um die Stützstrukturen zu sparen habe ich das Panel in mehreren Bauteilen gezeichnet. Leider habe ich es noch nicht drucken können da ich gerade Dienstlich unterwegs bin. Wird aber gleich…
This is an enclosure for this board from Waveshare with POE-module and OV2640-camera which you can get on Ali and other sources. not fancy or pretty, but functional, lightweight, space-saving and filament-saving ;P Addons I also made an…
just a simple single port wall plate for ethernet with a RJ 45 keystone
If you break off the handles they even work as a port lock. I printed them in PETG with a 0.6mm Nozzle and they fit pretty well. You'll have to use Flush-Cutters to cut them out of the grid or sand off the edges. If you want to print many…
made a mock-up for this board from Waveshare with POE-module and OV2640-camera so that I could build an enclosure around it. The enclosure can be found here Updates 2025-06-15: added LAN-LEDs and WS2812 LED locations
This is a remix of joostns “Dual RJ45 keystone wall mount” to fit better on my circumstances. I changed the rotation of the keystone mounts to make it more easy to unplug both, the keystone module and the rj45 cable. I noticed that the…
An ethernet RJ45 repair clip with a snap lock that locks the plug in the socket. This model is optimized for sideways print so that the snap lock prints with the layer lines to increase the strength. Use: 3 perimeters (walls) supports To…
Network Cable Protector – Durable RJ45 Clip Guard Protect your Ethernet cables from everyday wear and tear with this sleek black network cable protector. Designed to fit securely over standard RJ45 connectors, it shields the fragile…
RJ45 dust cover for any device (switch, router, computer...). Pull tab that make easy to remove Wide enough to cover all the port but small enough to fit in side by side port (network device). Print Settings Printer Brand: Creality…
We have switches / PLC's at work that occasionally get relocated. Every now and then, the wrong un-configured ports get used to re-connect these devices. These aren't really to stop people from pulling them out if they wanted to with some…
I was inspired by the many designs for RJ45 repair clips, but they all suffered the same issue - the retainer part was bulky, fragile and never fitted my oddball collection of cables. They also required supports. The cable tie method fits…
Easy to print RJ45 dust cap cover with no supports
A NAS and a switch tend to illuminate my bedroom due to unfortunate (but unchangeable) placement. I made a very slim RJ45 LED plug cover, which slides on easily and does not come off on its own when unplugging cables. Works also with…
I designed this tool, to assist in fabricating ethernet cables. It maintains wire formation, in preparation for insertion into the RJ45 Jack. It also assists in precisely cutting wires to (13mm) the correct length.. Strip off about an…
Based on: https://www.thingiverse.com/thing:4687836 I printed some of the clips of the above thing and noticed that they break quite easily because the clips are very thin. Also, I was struggling to get it to print nicely in PETG and had…
M920q cover for a 2.5gbe A+E keyed RTL8125B adapter. Probably also fits other Lenovo ThinkCentre variants
Hello i made this very simple but effective RJ45 keystone holder. this part can be implemented and mixed with other 3D designs that need a RJ45 connector to them. recommended to print with PLA and not with ABS. ABS is more prone to…
I wanted a quicker access for my ADXL345 Board, connected to the Raspberry-Pi under my VOROn 2.4 Printer. So i grabbed a “deleyCON Keystone Jack Modul” from Amazon, designed a Skirtinsert and there we go. Unfortunally, because of the Size…
A bracket to hold a X540-T2 in place on a m720q
RJ45 Ethernet Network Switch LED Light Shield Cover Print with any material
This is a remix of https://www.thingiverse.com/thing:2943086 modified to match the RJ45 connector specifications. There are several versions of the same model, regarding the wire diameter: 5.00 mm (4 dots) 5.25 mm (3 dots) 5.50 mm (2…
Holder for RJ45 Network Cable Tester that works with the Gridfinity system.
Just a big ole RJ45 Cat5 Ethernet Lan end. The bigger you print it, the more internet you get…. probably…. For faster-est internet, print with clear PETG and glue a cable to the end. PETG Whatever inner fill you want Supports required
RJ45 connector cover. Be sure to print with TPU! 100% fill required.
A simple wire management solution for securing network cables. It hold 14 ethernet cables and has multiple holes for mounting inside a server rack or under the desk.
Based of a great Thing Original didn't work for me with S3D, model was disconnected. Took a look in Tinkercad and there where some issues that I 'think' i got rid off
I needed some strain relief, but all I could find was not optimal for 3d printing. I modified Eiki Martinson's design a bit ( cable hole was too small, the ribs needed some fillets to be able to print properly and had to make the lever…
Cable Manager - Clip RJ45 Resize to adjust dimension If you download/enjoyed this file, please leave a like - Thx Category: Hobby
XLR to RJ45 Keystone Jack adaptor plate. It does what it says. Screw on the back of a D series XLR pane hole and push in any Keystone RJ45 socket. Print large side down, There is a sacrificial bridging layer to avoid need for any support,…
Simple RJ45 cable jack protector with no sharp edges, which can be printed without any support. Print instructions Category: Computer
RJ45 Inline Coupler Keystone Case This thing is a 3d printable housing for an RJ45 keystone. The reason it was developed was so that I could mount my spare Cat5e coupler into my CNC case without having to change the case design too much.…
RJ45 network signal cable fixing frame, you need to add adhesive by yourself
I wanted to be able to install my USB over ethernet adapter inside of my computer case. This is due to me preparing to move my pc into a server rack mounted case and I cannot have loose components hanging off the back of the computer.…
This is a baffle for the rear PCIe slot of Lenovo Tiny PCs including the M720q and others. The original baffle is from a user on Thingiverse by the name of simbaja and can be found here . I took the original model and tweaked it to my…
Designed a cover for the RJ45 Jack. Uses the geometry of the plug to hold it against the port nice and flush, however if your port is inset it will not work and you will need to edit the file to lower the bottom tab that the plug pushes…
Maj 24/07/2023 : Nouvelle version pour modèle X1 (non compatible avec adaptateur x2) sfpng_base3.stl Maj 05/07/2023 : ajout d'une version avec davantage de jeu : “cache-rj45-fit_large.stl” infill 100%, hauteur couche 0.15 ou 0.20 max pas…
Did not find here what I was looking for. So, another keystone mount. What do I think this can do better: sturdy lightweight easy to assemble releases keystone easyly is tight, but not too tight developed and tested with the cheap…
A little lock inspired by the panduit rj45 lock, this one is not meant to prevent anyone from unplugging cables but actually just locks cables properly so they don't pop out on themselves Print Settings Printer: self made Rafts: Doesn't…
This is a keystone insert for a voron 2.4 front skirt, so that an ethernet connector can give easy access to the SPI port on the controller board or the Raspberry Pi inside the printer. This is to simplify connecting an ADXL345 when…
Used 2 m3x40 screws. printed with: 0.6mm nozzle. 0.3mm layer height. 4top/bottom layers. Esun ESilk Pla.
There is nothing worst that breaking off the little clip on that long ethernet cable after its been ran through the ceiling and down the wall. Well, maybe trying to 3D print a replacement clip, because they are not design well or the…
RJ45 crimping tool mount
Need to get a network cable from A to B? Already got something in position you can attach to and pull through? This might be for you. This design prioritises strength at the pulling end, without requiring bridging, supports or challenging…
Bad port indicator Cover can be printed to indicate bad ports of network switches, routers etc. This is a remix of RJ45 Dust Cover Project Printer: Creality Ender 3 S1 Material: PETg Red Infill: 50% Support: Yes Layer: 0.15 mm
Rj45 Universal Patch Cable Manager / Cable PASS-Through 90 degree angle for Alu 2020 / 3030 / 4040 Profile Suitable for: 2020 -3030 -4040 -500 V-Slot T-Slot Alu profile - Rack 3d printer frame profile Server / Rack Resize to adjust…
Stop breking off the RJ45 plug latch.
This bracket is designed to be able to use an RJ45 panel mount extender cable to a PC tower. I needed a way to connect a device inside of my case to a network cable. This is the panel mount cable I'm using but it might work with other…
A Gridfinity 5x2 holder for an RJ45 crimper and a wire stripper. Wanted to be able to store these in my drawer without taking up much height. My RJ45 crimper default position is open, so to put it in I need to close it, which the…
Gridfinity holder for network crimper plier, made for a crimper with 19cm length, 6cm width at handle. 2x5x4 no magnets.
I needed one of these for a Leviton Decora insert and nobody stocked the 3-port versions locally. This is a bit of a tight fit to get 3 keystones in while still having the PLA be strong enough to hold. I use Cable Matters keystone jacks.…
In my IT work, I sometimes need to install single RJ45 jacks in odd locations. Wiring standards dictate that wires run into a wall jack or patch panel, but you don't often have the correct plastic jack on hand when you need it. I've used…
Gridfinity tray 4x2 (3u tall) with a hole shaped exactly to fit a very popular RJ45 crimp tool from aliexpress, sold under many different brands. There's a few variations but I'm fairly sure most of them will fit because the hole is…
Sometimes you want to run a wire through a shelf in your closet, but if your shelves are made of particleboard, the hole will be unsightly and sawdust will fall from it. It's even worse when you need a large hole, such as for an RJ45 plug…
I needed a 45 degree angled, single RJ45 wall mounted socket plate. This is based on the mounting for old RJ11 phone sockets (Sweden/EU), M3 screw-holes are 60mm apart. The socket slot fits one standard RJ45 keystone jack, I used…
Can be printed with PLA 0.4mm [email protected] layer height. Might also fit for other models
The Ethernet LAN Cable RJ45 Protection Cap is used to protect connector of the ethernet LAN cable.
Remix of great simple model of RJ45 cover - improved by simple hanger. I recommend using a layer thickness of 0.2
The two parts attach together and snap into place, enclosing the RJ45 cable and the cable itself. The idea behind this project is to be able to add boots to RJ45 cables after they have been crimped.
Simple Cable wall holder simple strong and easy to install No supports need. You will find two versions ( Double and Single cable ) Enjoy, Happy Printing
These are simple boots for RJ45 terminals. They're intended to be printed from TPU or some other EXTREMELY flexible material, otherwise, well, they just ain't gonna work… I printed these in an unbranded translucent purple 95a TPU. They…
Based on Gavitka's Wire Stripper (thing:4897773) I created my own design. It is smaller and it is only for cable of Ø6mm. Print Settings Printer: Voron 0.1 Rafts: No Supports: No Resolution: 0.20mm Infill: 25% Filament: Doesnt matter…
Just a cable clip that holds on to the rj45 port. For now only in a similar size as the “medium” version of the original. I might make a bigger one in the future.
Simple box for single keystone rj45 socket. Socket require slot on bottom and top to properly snap-in.
A box for 3 pieces of Keystone adapter.
About I made this for my ZTE MU5001 Mobile router, its RJ45 port is awesome but id guess it quickly gets full of lint and other stuff if i just throw it into my backpack. Only editing happened in PrusaSlicer, by adding a negative volume…
I was looking to connect two RJ45 and I had to hide them in a power distribution box. I found something similar in amazon but too expensive and not really what I need, therefore I start to design my own DIN Rail element. Printed with…
Under-Desk RJ45 Keystone Jack Bracket – 1, 4, 5 & 8 Port Versions Clean and sturdy snap-fit mounts for standard RJ45 keystone jacks. These brackets let you neatly install Ethernet ports under your desk, shelf, or workbench for easy access…
This is my take on the Voron 0.2 rear skirt which fits my requirement of having a convenient wired network connection and the spare USB port accessible, and the ports located in places that don't get in the way of the standard cooling fan…
