Aoue-MCL8 Lesu dozer blade
2.0 mm layer height, 20% infil, 3 perimeters. Tree Supports.
Wydruk około 3,28 €–4,01 € nettoWstępna wycena jednego wariantu
- Pobrania
- 64
- Polubienia
- 3
- Ocena
- 0
Liczymy pasujące modele…
2.0 mm layer height, 20% infil, 3 perimeters. Tree Supports.
Wydruk około 3,28 €–4,01 € nettoWstępna wycena jednego wariantu
Coupling for microwave oven TEKA ML820BIS. The coupling on my microwave oven broke (it split where the motor
Wydruk około 0,39 €–0,48 € nettoWstępna wycena jednego wariantu
The only hardware you need to supply are two M3 inserts (I use ruthex) and two M3x6 (or 8mm) screws. I printed mine in PolyLite ABS, but PETG would probably be more than enough. I don't recommend PLA. Be sure to account for shrinkage if…
I consider this a WIP due to how variable my experience with the inkjet print process has been . Please comment with feedback from your experience with the process. Model Info This is designed around standard NFC PVC Cards (54mmx85.5mm).…
This light mount holds your Varia on the seatpost of your Tarmac SL8 elegantly. It weights only 9.8g with M3x22 stainless bolt, M3x5x4 insert and a 15% infill. Works fine with PLA if you like colors, but prefer PA-CF for durability. Print…
Remix of original model: https://grabcad.com/library/the-male-figure-carl Changes on model fits to seat of 3Dsets Model 8 Buggster his right leg is shorter, fits to pedals right hand on other position brand new ears less belly fat more…
Tested on my HSKRC XL Frame (XL9 Arms), which is very close to the iFlight XL7. Standoffs in my case are 5mm (which could differ from the iFlight model), so the holes are tailored to that size. I added a TBS crossfire antenna holder to…
This is a simple adapter to fit the Xiaomi Mijia Lite monitor light onto the LG 27GL850. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: Office
Simple case & snap-on lid for the RTL8720DN BW16 board. I couldn't find any other models available for this board, so I made one! The snap-on lid press fits snugly, and has supports to help hold the board in place. Pins are exposed on the…
Remixed version for cheap multimeter XL830L
Rail adapter for ICS L85 Series to enable mounting of RIS/picatinny mounting optics and accessories. The model has a built in support. Print on the support side, with no supports for best results.
This adaptation features several improvements that make the clamp more secure: the part that goes around a seatpost is shrunk by 1%, the holder part is narrowed down by 1mm and canonical design is added to lower the force exerted on the…
For refilling Epson L8050 (and probably other printers with a 6mm filling sprout) with CUYI sublimation ink. No drips, no ink on the hands. The silicone sprout of the ink bottles fits snugly. Printed on a well-tuned Bambu Lab X1C. Torwell…
etsy.me/3n6BXUo bit.ly/42oqoYP SA80 / L86A2 Pistol Grip by saxonite - Thingiverse Please leave like if you download this model, it goes a long way in motivating me to continue making polymer furniture & replicas, I appreciate it! Replica…
Simple medium shelf. Dimensions W:85mm, D:65mm. Prints with no supports. Works well with PLA and PETG. If this was in a hot garage I recommend PETG which will hold up better to high temperatures. Additional necessary components You also…
Adjusted with PrusaSlicer, so it may not be pretty, but it just works. -You may need to hold the right side down as you screw in to prevent the print from twisting. -The right screw threads into the print. Refrain from over threading.…
This is an original adapter plate to allow mounting an Ali-Express 2.5Gbit RTL8125b adpater to the HP Mini's FlexIO V2 slot Designed it to mount the socket upside down so it better aligns to the slot at the rear of the HP mini. Also have…
A box with lid for the popular TL866 II EPROM programmer. Helps keep all the accessories together and saves you having to work out how to get it back into the cardboard box it came in. Lid is pretty loose, so best kept in a drawer…
etsy.me/3n6BXUo bit.ly/42oqoYP L86A2 LSW Vertical Grip / Rear Pistol Grip SA80 by saxonite - Thingiverse Please leave like if you download this model, it goes a long way in motivating me to continue making polymer furniture & replicas, I…
Water funnel for filling Lelit Grace PL81T from the left side, since mine is positioned under a sloping roof on the right. Still able to use the original lid to close the top.
Cable Holder for Märklin S88 / L88 with Ebrom H05V-K 0,5 mm² Used screws: 3x16 Spax Filament: Prusament PLA Jet Black Category: Electronics
Divers with double or side mount rig are frequently using pulleys, so called miller carts, to carry their tanks. I modelled a holder for AL80CU tanks for my rig. I also enclosed the Fusion 360 files with the parametric design so one can…
WARNING It's static model, so it may doesn't fit some types of rails. You can make it fit by reengineering the bogies ENG: The VL80T (ВЛ80Т) This is N scale model of train "VL80T" It was used on USSR/CIS countries/Russian railroads. The…
My little niece broke the battery cover while trying to replace the batteries on her Lexibook alarm clock. My brother asked me to design and print a new lid. So here it is. Maybe it will be useful for some people too. My Print Settings:…
Hier könnt Ihr euch ein Ersatzrad (für extreme Steigungen) für den Ambrogio L85 drucken. Das Modell ist so erstellt, dass es auf einem Prusa MK3 ohne Support gedruckt werden kann. Gedruckt habe ich alles mit einer 0.6 Düse, 0.3…
Protect the inputs shaft of a 4L80e transmission from damage during storage.
etsy.me/3n6BXUo bit.ly/42oqoYP Butt Plate / Stock L85 / SA80 by saxonite - Thingiverse Please leave like if you download this model, it goes a long way in motivating me to continue making polymer furniture & replicas, I appreciate it!…
Introduction I like to keep everything in my gun safe tidy and make use of the otherwise unused wall space. Since the safe is lined with fabric, I designed a series of magnetic holders for magazines, firearms and accessories. Strong…
3D printable SSD bracket that you can use to attach 2.5" 7mm SSDs in 45HomeLab HL8 and HL4. We recommend using either PETG or PLA with a decent heat deflection temperature (>50C) with 3 perimeters and at least 15% infill.
These are part to be printed for functional Bolt Hold Mod by Frog Engineering. For manual how to do the mod, see link b
Mount your rockbros RHL800 flashlight to a gopro mount. Prinzed in TPU A95, but also ASA would be suitable.
Rail riser for an airsoft ICS L86. The rail I used is proprietary, but I've included the STEP file so you can customize the top to match what you have. Prints in two halves and then is fastened together with 9x M3x25mm socket-head screws.
Case designed for this board You also need this type-c board Print case & cover Place m3 inserts: 2 for board & 1 for cover mounting Unsolder USB cable & solder USB type-c board on rtl8812au board Take 3 m3 screw & assemle it Test it &…
Ein zweiteiliges Modell zur Reparatur des Drehgelenks an der Makita Akku Leuchte DML801. Die Bauteile können ohne Stützmaterial gedruckt werden und ersetzen das original Drehgelenk, ohne das die Kabel im inneren der Leuchte abgelötet…
I needed an Adam Hall 8708 sized dish for my tops, but for NL8MPR connectors. I couldn't find any on the market, so here we are. There are two files: the single socket one has a 42 x 34 mm sticker zone, very slightly recessed. The sticker…
27GL850 has recessed VESA mount, so you need standoff with 5mm thickness you need 4 pieces of M4x12mm or longer
I own a LG GML844PZKZ fridge. The files provided are for that model number. I suspect, that there are other versions with only small differences (ice maker etc. - using the GML844 designator) that those files would work with too. If you…
RP018250 Pivot Pin for Bracket on Flexzilla L8250FZ Retractable Air Hose Reel NOTE: I ordered a set of this part number (pins) from Flexzilla, and they were not correct. The pins in my air hose reel are pointed, and the pins I received…
Create a mount in OnShape for the PCL811. Was inspired by other designs but wanted one with 2 screw holes and can be printed without supports. Top/Bottom can be either side, with #8 wood screw holes as part of the print. I have them 6…
3 perimeters/walls, 0.2 mm layer height, 20% gyroid infill
A couple of Ikea Livboj charger puck holders. One is for larger phones and phablets like my Power Armor that need a 40 mm distance from the bottom of the phone to the charging puck. The other one is for a Pixel 8 Pro. I'm told it works…
Thermal paper roll stand for Model PL80E Polono Thermal Printer I used PETG but PLA will certainly work as well
This is an old, generic percussive (thumping) back massager that came with a couple heads, a rounded one and a bumpy one, and my spouse requested a pointier version of the rounded head to target muscles better. I measured the threads on…
用于ssc338Q相机和RTL8812EU的OpenIpc外壳,用于测试无人机
I didn't like the pegs that eventually break. I think that t-clips are better, so i edited it.
A backplate for using the single port RTL8125B network cards with the Lenovo ThinkCentre M720 Tiny. Tested and fits the Fenvi 2.5G RTL8125 PCI-E network card, but should fit most other models and brands as they seem to use the same…
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
Printed with tree supports, oriented cup-side-up. Recommended PETG or better for UV and temp resistance. Install is simple, pop original blanking plate out with flathead screwdriver on side with indent, then slot in with arrow facing…
This is a travel case for the L87 Digital Voice Recorder found here - https://www.amazon.com/dp/B09XF2Z12G The red one in TPU and the black is PETG printed with fuzzy skin enabled. The PETG case snaps together better and holds together…
Filler neck for my “Lelit Kate” espresso machine As my coffee machine is placed under a kitchen cupboard, filling the water tank is not very convenient. Unfortunately, I couldn't find a suitable model that I liked, so I designed my own…
Replacement for a worn out Sigenia TL860 Balcony Door latch. Print instructions Best print out of a very sturdy material with 100% infill to withstand the forces of the door closing.
To protect the housing of the Heckler & Koch SL8 / G36, I wanted to cover the part next to the ejection chute. I used TPU filament for the print. Thin double-sided tape is recommended. Category: Sport & Outdoors
This is a spare part replacement for the stem of a sink plug. The original stem was in plastic and broke in a few months. Most of the stem of the brand Franke are metallic but this one is plastic and has a notch to switch between open and…
Pretty self-explanatory I think! It printed best for me with the AirTag hole facing down and a little bit of support. It worked without supports but best with a little support. Make sure to install it with the drain hole facing down!
This is an adapter to mount a Fanatec CSL DD in the top head tube of the Simul8r racing cockpit. Parts needed: 8 x M6x8mm t-slot nuts. Wheel base includes 4 but you will need to purchase 4 more 8 x M6x20mm cap screws 2-4 M6 bolts with…
The model contains a support for the screw recess
Adaptation for Lenovo M720 or M920 for XWYWX X2R2115 version of Realtek RTL8125b dual 2.5 RJ45
A compact solution for fastening a Spedal CL871 touchscreen for Apple CarPlay / Android Auto to a common 22mm diameter bracket on my wife's Honda Transalp XL 750. What you need Please note: All links to Amazon ( amzn.to ), AliExpress (…
This is transport for following tripod and camera light. VIJIM Ulanzi MT-08 Foldable Tripod VIJIM VL81 LED Video Light Camera
Electrode Tweezer for ABL800 (700, 800, Flex etc.) Designed to remove the electrode from its position without the need for direct contact with the electrode itself. This method ensures safety by minimizing the risk of accidental contact…
De KPN-afstandsbediening muurhouder is een handige oplossing om je afstandsbediening altijd binnen handbereik en netjes opgeruimd te houden. Deze muurhouder kan op twee manieren worden bevestigd: met een schroef voor een stevige,…
Sparepart for repairing the ampstut of a BL8000
these plugs are for blocking the intake ports on the cylinder head for gen 5 GM small block LT engines. in your slicer you may have to scale the model up or down a couple percent due to gm not making all these things exactly the same.
An under-bottle mount for daysaver essential8. Unlike the branded version, this one does not require spacers to fit under a bottle cage. Print with supports at high infill. I used PETG; for all the weight weenies my print (60% infill,…
Wall mount for Extech TL809 Test Lead Kit. Attach to wall or shelf with flat head screws. Print Settings Printer: Sindoh 3Dwox Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 layer height Infill: 15% How I Designed This Imported my…
I build this frame for my old Grundig isolation transformer
The battery on my Samsung L830 expanded making it unusable so I made this adapter that uses the original bms to trick the camera into running off any 3-4.2v power source. The original battery door doesn't fit with this mod so you will…
Cube_4x4x4_E1_K3_L8 - Peng Song A size 4 cubic puzzle of 3 pieces, rated at level 8 (moves to remove first piece). Adapted from web page: https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
A) NOTICES (herunterscrollen für deutsche Version / scroll down for German language version) Non-commercial provision of construction files in . stl-format for a chainstay frame plug for my Specialized Tarmac SL8 Pro road bike by the…
These are sprockets for 8mm film, specially designed for the T-Scann8 scanner. They are designed for a 5 mm D-shaped shaft. Be warned: they are nearly impossible to print, the teeth will most likely require post-processing to turn out…
This is a 1x5 Gridfinity nest for a bigger-than-average desoldering pump (IYKYK)... It's usually blue and yellow. The plunger hangs off the edge of the tray, which allows this tray to be printed on most printers. Otherwise, the tray would…
Cube_4x4x4_E1_K5_L8 - Peng Song A size 4 cubic puzzle of 5 pieces, rated at level 8 (moves to remove first piece). Adapted from web page: https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
The Spedal CL871 is a great affordable screen for your motorcycle. But the 600 nits struggles a little in daylight. This sun shade is modelled to fit the contour of the unit. It fits pretty true but, if you ride a thumper like me, you…
Gontier_5x5x5_E1_K4_L8 - Peng Song (Gontier adaptation) A size 5 cubic puzzle of 4 pieces, rated at level 8 (moves to remove first piece). Adapted from web page:…
Cube_5x5x5_E1_K8_L8 - Peng Song A size 5 cubic puzzle of 8 pieces, rated at level 8 (moves to remove first piece). Adapted from web page: https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
This paper roll holder for the Polono PL80E is an improved version of an existing roll holder. It is now possible to use much larger paper rolls. The roll holder can be printed using all standard materials.
This is an upgrade for the Makita 18V LTX Lantern, 20 LED bulb variant. This may work on the other variants, but I don't have them to test. If you aren't certain which variant you have, the correct version is green & has a USB port. I use…
The Daysaver Essential8 multitool is a pretty slick bit of kit! I didn't buy their Hug tool sleeve when I purchased the tool, but I quickly realized I did, in fact, want to cover the hard corners to reduce the risk that the tool abraded…
Cube_5x5x5_E1_K6_L8 - Peng Song A size 5 cubic puzzle of 6 pieces, rated at level 8 (moves to remove first piece). Adapted from web page: https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
Short Rail Carry Handle G36/SL8 for AEG/ Gel Blaster
Ich wollte etwas Farbe an mein SL8 bringen und habe darum den Magazinkasten erstellt. Auf die glatte Seite habe ich noch ein Symbol aufgedruckt. Das hier ist die "glatte" Version zum selbstgestalten.
한개의 wifi 카드만 사용한 VRX 케이스 입니다.
A cup holder insert to hold your SMOK AL85 so it doesn't jostle around while you're driving. Category: Automotive
printed on my ender 3 on 83% scale. recommend you do the same. (exept the printer.)
This model is a 1U 10-inch rack mount, designed specifically for the ONU XPON PL8800Z All model CAD files are fully open-source and available for download Check out the GitHub repository to explore the project Variants To accommodate…
Ersatzknauf für Regelventil für Sondiko L8010
Insert for LocknLock HPL889 (12L) container for better storage of the filament spool. The dimensions of container are almost perfect, and with the inserts, spools sit inside without moving. The components are interconnected to form…
Hello, I have modeled these covers to fit on a Zipp SL80 Race handlebar where the Sprint Blips would sit. I dont know if it will fit to any other similar handlebars but you can give it a shot. I printed in PETG, also went quite slow and…
Basic simple no support required plate for fastening a 2.5g dual RTL8125B network card into a Lenovo M920Q machine. Is also compatible with M720 machines. Uses all stock screws and is best produced using PETG filament. Please like and…
The Makita XGT ML006G LED Flashlight, and the equivalent LXT DML816, hinges to allow adjustment of the direction that light is projected. This hinge is made of plastic and if the flashlight is dropped it is prone to breakage. This hinge…
Designed for a 2025 L8T 6.6L 2500 GM truck. Print upside down(I added fuzzy skin). Also purchased new o-rings for the oil cap and placed one around the base.
Cube_5x5x5_E1_K4_L8 - Peng Song A size 5 cubic puzzle of 4 pieces, rated at level 8 (moves to remove first piece). Adapted from web page: https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
Holder on the wall for switch HUAWEI S5731-L8P2HT-RUA with adapter. The print must be with supports.
Makita DML800 18V LXT Lithium-Ion Cordless LED Headlamp hanger, wall mounted holder, labelled with DML800. Two versions, horizontal and vertical. Attach with two number six screws. Print as pictured. No supports needed. Battery Holder…
Gontier_6x6x6_E1_K5_L8 - Peng Song (Gontier adaptation) A size 6 cubic puzzle of 5 pieces, rated at level 8 (moves to remove first piece). https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
Gontier_5x5x5_E1_K5_L8 - Peng Song (Gontier adaptation) A size 5 cubic puzzle of 5 pieces, rated at level 8 (moves to remove first piece). Adapted from web page:…
This is a simple cover to protect the lens and the button. Using the cover will reduce the need of unplugging the batter
A simple mount for the inexpensive L80 module from Quectel. This GPS module is based on the mediatek MTK location engine. Find more details here: https://www.quectel.com/UploadImage/Downlad/L80_Hardware_Design_V1.1.pdf The mount makes…