Wyniki wyszukiwania: sg105

Sortowanie

Liczymy pasujące modele…

P

TP-Link SG1005P | SG105 10-inch Rack Mount

A sturdy 10-inch rack mount adapter for one or two TP-Link SG1005P. Also works with the SG105. To install the switch, simply slide it in. However, if you already added the rubber feet, remove them before installing the switch in this…

Pobrania
1095
Polubienia
89
Ocena
5
P
PrintablesBlenderBender

TP-Link SG105 10 inch rack mount

This is a 10 inch rack mount for a TP-Link SG105. I have printed it whit ABS. No support needed, I have added a custom support in the model. If you need a 10 inch rack mount for a different brand or you just need a cover plate I will…

Pobrania
724
Polubienia
64
Ocena
4,5
P
PrintablesKIL0

TP-Link TL-SG105 mount

Mount for TP-Link TL-SG105 with cut outs for air vents. Under the mount are two channels for the dc supply cable. Mounting is done with 4mm sink head screws. Print with front facing down.

Pobrania
534
Polubienia
47
Ocena
4
P
PrintablesDiew

10 inch rack TP-Link SG2210P - SG2008 - SG105-M2

It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…

Pobrania
415
Polubienia
45
Ocena
5
P
Printablesjnr0790

TP Link TL-SG105 Mounting Plate

This is a remix of this mounting plate by asp55 on Thingiverse. This one has the inserts a bit closer than the original to fit newer TL-SG105 switches. Just use double sided tape or whatever you want to mount the plate and attach the…

Pobrania
320
Polubienia
22
Ocena
5
P
PrintablesAngel Rivas

U1 10" Inch Rack Mount for Raspberry Pi 4 and TL-SG105

UPDATE: 25/02/2025 I have updated the design, to compensate for the MicroSD card in the Raspberry Pi, and also adjusted the end of the router back to fix some occasional XYZ errors while printing. U1 10" Raspberry Pi 4 and TL-SG105 Rack…

Pobrania
307
Polubienia
38
Ocena
4
P
PrintablesDanielmaxsteel

TP Link TL-SG105 under desk mount

I designed this holder for mounting the TP-Link SG105 under my height adjustable desk. I used 2xM3 screws with fitting nut and 2x M3,5x16mm wood screws. I placed the nut inside the Screw-Terminals of the switch and fastend the screws…

Pobrania
302
Polubienia
40
Ocena
5
P
PrintablesJascha3D

TP-Link TL-SG105 10-inch Rack Mount

TP-Link TL-SG105 10-inch Rack Mount 🖥 Keep your TP-Link TL-SG105 securely mounted in any standard 10-inch rack! This remix adapts the original 8-port TL-SG108 design to fit the 5-port TL-SG105. It adds a robust latch rather than relying…

Pobrania
295
Polubienia
27
Ocena
0
P
PrintablesBak3

tplink tl-sg105 1U rack shelf

1U rack shelf for 8 port ethernet switch tl-sg105 print settings: 15-20% infill 0.2 layer height

Pobrania
282
Polubienia
50
Ocena
0
P
PrintablesTdewulf

TP-link TL-SG105 mount

Wall and ceiling mount TP-link TL-SG105 made in thinkercad 3mm thick walls

Pobrania
269
Polubienia
16
Ocena
5
P
Printablest0b1

Hanger for TL-SG105 network switch

Wall mounting bracket for our TP-Link TL-SG105 network switch.

Pobrania
264
Polubienia
23
Ocena
5
P
PrintablesBasti.mp4

TP-Link SG105E 10" Rack mount

Little remix to mount a TL-SG105E in your 10" Rack. You have to remove the two little screws under the switch. After that you have to slide the switch in the mount until its flush with the front. The last step is adding two M3x6mm screws…

Pobrania
257
Polubienia
18
Ocena
5
P

TP-Link SG1005P | SG105 | OC200 6-inch Rack Mount

A 6-inch Rack Mount for the TP-Link SG1005P | SG105 | OC200 series. This model is part of a series of 6-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a coffee ;) Print…

Pobrania
254
Polubienia
22
Ocena
5
P
PrintablesSpeeter

TP-Link TL-SG105 mount for IKEA SKADIS

An easy way to mount you TP-Link switch to the SKADIS pegboard

Pobrania
214
Polubienia
20
Ocena
5
P
PrintablesCeleste

Sturdy 10 inch rack mount for the TL-SG105E consumer network switch

------------------------------------------------------------------------------------------------- UPGRADED PARTS AVAILABLE! Click the link to get to V.2 of this part:…

Pobrania
211
Polubienia
36
Ocena
5
P
Printablesflyingtoaster0

Mount for TP-Link TL-SG105 Network Switch

This is a mount for a TP-Link TL-SG105 network switch. This can be used to mount the switch under a desk or to a wall. Printed on an Elegoo Neptune 3 Pro with Elegoo PLA. I used 6 x ½" wood screws for mounting. To ensure a snug fit, the…

Pobrania
197
Polubienia
13
Ocena
5
P
PrintablesHenri S

tp-link TL-SG105PE Switch 10 inch rack holder

You need zipties for the power brick. The switch slides into the mounting brackets and locks itself in place. There is also a version for 19 inch racks:

Pobrania
186
Polubienia
30
Ocena
5
P
PrintablesDiew

10 inch rack TP-Link OC200 - SG105

remix from 6.5 inch rack i dont have device to test this print, use at your own risk If you enjoy my work, please consider support at link in profile.

Pobrania
175
Polubienia
9
Ocena
0
P
PrintablesiKlaus

TP-Link TL-SG105 Skådis Mount

Mount for TP-Link TL-SG105 Switch on IKEA Skådis pegboard

Pobrania
170
Polubienia
14
Ocena
5
P

TP-Link TL-SG105-M2 2.5G 10-inch Rack Mount

A 10-inch rack mount for the TP-Link TL-SG105-M2 2.5G switch. This model is part of a series of 10-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a coffee ;) Print Settings…

Pobrania
147
Polubienia
12
Ocena
0
P
PrintablesKaosuNeko

Tenda SG105 Gigabit Ethernet Switch DIN rail mount

Tenda SG105 Gigabit Ethernet Network Switch DIN rail mount You can use standard mounting holes. Lock the nut into the part and tighten the screw so that the network switch is firmly in place. Try a few times. You can also use a drill, for…

Pobrania
144
Polubienia
18
Ocena
0
P
Printablesidcrook

10" inch 1U rack mount for side-by-side Raspberry Pi 4 and TL-SG105E Ver. 3

Wanted to use in my 10-inch rack setup since I need the extra space under the Pi for an errant tall PoE HAT in a 1U rack below where this rack will be installed. I subtracted some of the material from the print model surrounding the…

Pobrania
142
Polubienia
8
Ocena
0
P
Printablesottk3

TL-SG105 Screwable Mounting Plate

Mounting Plate for TP-Link TL-SG105 switch. Material: PLA+ Infill: 20% Support: Touching Buildplate

Pobrania
141
Polubienia
7
Ocena
5
P
Printablesmaciek18339

TP Link SG105 mounting bracket

This mount is easy to print, resource friendly and reliable. There is no need to use two handles. But it can certainly add grip security. You can use doublesided tape/something else to make it REALLY tight. I'm recommending PET-G or ABS…

Pobrania
128
Polubienia
21
Ocena
5
P
PrintablesDespairFlare

TP-Link TL-SG105 Wall Mount - Renter Friendly

This is a renter friendly wall mount designed for the TP-Link TL-SG105 5-Port Desktop Switch. Add 3M Command Strips (or something equivalent) to the back of the mount, put it on your wall, and hook the network switch onto it. Printed in…

Pobrania
128
Polubienia
8
Ocena
0
P
PrintablesSwampy

TP-Link TL-SG105 Cable Bracket

Update 11/18/2024: I have added a version with larger openings for round cables. This is a quick little cable bracket for the TP-Link TL-SG105 5 port ethernet splitter/switch. Bracket will snap or slide into place on the unit. It allows…

Pobrania
125
Polubienia
21
Ocena
0
P
Printablesbatonikleonardo

TP-LINK TL-SG105 rack10 mount

Rack10 mount for switch TP-LINK TL-SG105

Pobrania
121
Polubienia
21
Ocena
0
P
PrintablesiahiMsogarD

Tplink TL-SG105E Rack mount

Print with the wing on the bed.

Pobrania
109
Polubienia
12
Ocena
0
P
Printablescloudybasement

Skadis - TP-Link TL-SG105 Network Switch

Bracket to hold a TP-Link TL-SG105 Network Switch on an IKEA Skadis pegboard using the built-in keyhole mounts.

Pobrania
104
Polubienia
11
Ocena
3
P

TP-Link TL-SG105-M2 2.5G 19-inch Rack Mount

A 2 part modular 19-inch rack mount for the TP-Link TL-SG105-M2 2.5G switch. This mount is part of a 19-inch modular rack mount system I designed, you can mix and match the modules with other mounts. Take a look at my models here to find…

Pobrania
101
Polubienia
7
Ocena
4
P
PrintablesConstantin.B

TP-Link TL-SG105 5-Port Switch Halter

Meine Empfehlung ist denn Halter mit 20% zu Drucken Wird mit 2 3mm Schrauben an eine Holz platte angeschraubt.

Pobrania
97
Polubienia
9
Ocena
4
P
PrintablesCeleste

Celeste's sturdy 10" rack-mount panel V.2 for TL-SG105 (-E)

Notice ℹ This mount also fits the "NETGEAR" and “D-Link” equivalents of the equipment mentioned here, since they all use the same chassis from the same OEM's Accton Technology and Delta Networks .Notice ℹ This mount also fits the…

Pobrania
92
Polubienia
9
Ocena
0
P
PrintablesBlaahen

TPLink SG105 vertical stand

Vertical stand for the TP Link SG105 switch. If your printer is perfectly accurate this should be a decently tight fit. Very stable with a small footprint. Also included a cut out notch as it appears the SG105 has air vents on the sides…

Pobrania
83
Polubienia
16
Ocena
5
P
PrintablesRCmodeleng

TP-Link TL-SG105 Network Box Mounting Bracket

A lightweight bracket designed to hold the TL-SG105 TP-Link Desktop switch. Can be mounted to any flat surface, wall, cupboard etc. The mount is customised to suit the ports and requisite access points of the switch box. the mount is…

Pobrania
66
Polubienia
13
Ocena
0
P
PrintablesK7162

TP Link TL-SG105E Mounting Plate

A mounting plate for the TP Link TL-SG105 E network switch that allows you to attach it to a flat surface using double-sided tape. I recommend using PETG or another strong filament to keep the screw heads from breaking off. Print with…

Pobrania
62
Polubienia
4
Ocena
0
P
PrintablesDiew

6.5 inch rack TP-Link OC200 - SG105

Click to Read About 6.5 inch and Rack Frame 6.5 inch Rack Mount Collection It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on…

Pobrania
59
Polubienia
10
Ocena
0
P
Printablespanji

TP-Link TL-SG105E flat mount

For the TP-Link TL-SG105E. Air vents not coverd, all ports/connector remain useable, all LEDs visible.

Pobrania
56
Polubienia
6
Ocena
0
P
Printablesclemcoste

Hanger for TL-SG105 network switch

As mine broke a few month after printing, I decided to robustify it. Very good design from t0b1 Category: Electronics

Pobrania
55
Polubienia
7
Ocena
0
P
Printablesantonmuentz

TP-Link TL-SG105-M2 Mount

Underdesk mount for the TP-Link TL-SG105-M2 (2.5Gbit 5-port Switch). You can either print the (Bracket Top Left & Top Right) OR (Full Bracket & Magnetic Cable Holder). I have not tested the full bracket yet, will do so soon. Materials…

Pobrania
54
Polubienia
4
Ocena
0
P
PrintablesKieran

Dual TP-SG105 Switch Mount for 10" Rack

Dual TP-SG105 Switch Mount for 10" Rack Takes forever to print but worth it, tolerances don't matter too much, just sand down sides a little if too tight.

Pobrania
54
Polubienia
5
Ocena
0
P
PrintablesHenri S

tp-link TL-SG105PE Switch 19 inch rack holder

You need zipties for the power brick. The switch slides into the mounting brackets and locks itself in place. There is also a version for 10 inch racks:

Pobrania
52
Polubienia
4
Ocena
0
P
PrintablesFadenB

Netgear Switch TL-SG105E Bracket for Multiconnect

This bracket is designed to mount a Netgear TL-SG105E 5-port network switch on a Multiboard grid using the versatile Multiconnect connector system by DavidD . Print the Model The clearances are optimized for a tight fit and work well with…

Pobrania
52
Polubienia
11
Ocena
5
P
PrintablesSmarch

6" Rack Enclosure - Netgear TLSG105 PE mount

Remix of the 6" enclosure to mount a Netgear TLSG105 PE mount PoE switch. Printed in PLA, face down, without supports.

Pobrania
51
Polubienia
16
Ocena
0
P
Printableszeitverschreib

TP-Link TL-SG105 mount for Skadis

Just an easy to print mount for the SG105 switch.

Pobrania
41
Polubienia
6
Ocena
0
P
Printablesacn

TP-Link TL-SG105E DIN rail mount (35 mm)

Minimal remix for the TP-Link switch. Fix M3 nuts into the place as on the photo, screw in the bolt to the exact height and attach the switch.

Pobrania
39
Polubienia
2
Ocena
0
P
Printablesfaydee

TL-SG105 1RU Shelf

Simple remix rack mount for the TL-STG105 switch. You can print this face down orientation Should not need any supports I printed it with a 15% infill and 2 walls. I have 2 of these, so I printed left and right. But you can also print a…

Pobrania
39
Polubienia
5
Ocena
0
P

TP-Link SG1005P | SG105(E) | OC200 7-inch Rack Mount

A 7-inch Rack Mount for the TP-Link SG1005P | SG105(E) | OC200 series. This model is compatible with the GeekPi RackMate TT (Affiliated link). This model is part of a series of 7-inch rack mounts I've designed. You can check out the…

Pobrania
36
Polubienia
2
Ocena
0
P
PrintablesderConnor

Under Desk Mount for TP-Link SG105E Switch

This model has tight tolerances. I would recommend printing it from PETG due to the heat that might be produced from the switch.

Pobrania
35
Polubienia
2
Ocena
0
P
Printablesallex

TL-SG105PE 10" Rack Mount

Printed in PLA, seems to be fine with the heat.

Pobrania
34
Polubienia
4
Ocena
0
P
PrintablesOliverP

TP-Link TL-SG105 Holder for Wakoma Nimble Rack Systems

This is a 2 sided holder for TL-SG105 units, that makes them compatible with Wakoma Nimble racks

Pobrania
34
Polubienia
11
Ocena
0
P
PrintablesHelix751

TP-Link TL-SG105 switch mount (screwed+fixed)

My new TL-SG105 doesn't fit the original mount downloaded here. Vendor design changes perhaps? The original mount peg positions are 14.33mm too far from the tab border and are also too big to get through the “+” holes on the switch. What…

Pobrania
31
Polubienia
5
Ocena
0
P
PrintablesBitByteShark

TP-Link SG105 Network Switch Mount for Vesa

Adapter to mount the TP-Link SG105 Network Switch to one of the TV Backside Vesa screws

Pobrania
31
Polubienia
7
Ocena
0
P
PrintablesBitboard

TL-SG105 Network Switch wall mount

I designed this model so that I could mount my network switch to my wall for my homelab. The model was designed in TinkerCAD, and the design can be accessed here: https://www.tinkercad.com/things/6CWzo7I8oKr-tl-sg105-cradle

Pobrania
30
Polubienia
11
Ocena
0
P
PrintablesGrumpySquatch

TP-Link TL-SG105 5-port Gigabit Switch Shelf Hanger

Needed a way to get a small 5-port network switch off of a shelf to make room. Decided to hang it underneath the shelf above. Designed this holder specifically for the TP-Link TL-SG105 switch and to hang from standard hardware-store wire…

Pobrania
30
Polubienia
6
Ocena
0
P
PrintablesGreyBoy

Skadis Hook for Teda SG105 Switch

I needed to hang my tenda SG105 switch on a ikea-skadis-like pegboard so I took Juan's hook and attached it. Original thing: https://www.thingiverse.com/thing:3413856 I would print the hooks first and then either the horizontal or…

Pobrania
27
Polubienia
2
Ocena
0
P
PrintablesAntonioGPS

Minimalist support for TP-LINK TL-SG105

I have a small communication box where I need to fix the TP-LINK TL-SG105 unit. Most models I have found have floating parts or are too big, so I decided to have my own minimalist design

Pobrania
26
Polubienia
1
Ocena
0
P
Printablescreichert

TP-Link TL-SG105-M2 5 port Wall Mount

A wall mount for the TP-Link TL-SG105-M2 5 port 2.5Gb switch. Uses command strips. The keyhole mounts are 150mm apart, so this mount may fit other devices with this keyhole mount width. The keyhole pegs will work in either the vertical or…

Pobrania
26
Polubienia
2
Ocena
0
P
Printablesfuzzylogic88

TP-Link TL-SG105S-M2 Switch Wall Mount

Remix of DespairFlare's "TP-Link TL-SG105 Wall Mount - Renter Friendly" model for M2 version

Pobrania
25
Polubienia
4
Ocena
5
P
PrintablesErovia

TP-Link TL-SG105S switch mount

Mount the TP-Link TL-SG105S switch on its power adapter to avoid/reduce under-desk clutter. The switch slides in from left side and locked in place by the cables. Notes : I designed this with the UK adapter (Type G) in mind, can't test it…

Pobrania
25
Polubienia
3
Ocena
0
P
Printablesjublin

Pegboard Hanger for TL-SG105 network switch

Took the model for TP-Link TL-SG105 Switch https://www.printables.com/model/66935-hanger-for-tl-sg105-network-switch and added pegboard pegs from https://www.printables.com/model/225209-pegboard-peg/files

Pobrania
22
Polubienia
1
Ocena
0
P
PrintablesKrekos

10" rack mount Tp-Link SG105 and PI4

Mount for TP-link switch SG105 and PI4 on 5mm standoffs

Pobrania
20
Polubienia
3
Ocena
0
P
PrintablesScoobert

TP-Link TL-SG105S-M2 | 5-Port Multi-Gigabit 2.5G Ethernet Switch 10" Rack Mount

Fits that specific model, but may be tweaked for other models as needed via the main files.

Pobrania
19
Polubienia
2
Ocena
0
P
PrintablesMasta Blasta

TP-Link tl sg105 mount bracket

The power cable "ring" doesn't require supports, but the mounting plates does. I recommend using an interface material with a ironing function on the top surface of the supports to achieve a smooth surface (hints in the screenshot). For…

Pobrania
17
Polubienia
3
Ocena
0
P
PrintablesLvL_Dani

SG105 & OC200 modular rack mount

SG105 & OC200 modular rack mount requires 1u rails https://www.printables.com/@LvL_Dani_470947/collections/2036642

Pobrania
16
Polubienia
1
Ocena
0
P
PrintablesArty1223

TP-Link TL-SG105 Diagonal mount

I did this to mount a switch under a table. I recommend printing as shown in the picture (the .3mf file is exactly the same) to minimize the risk of layers peeling off from each other during screwing down.

Pobrania
14
Polubienia
1
Ocena
0
P
PrintablesSupreme2k

Tenda SG105 5 port switch wall mount

Bracket for the Tenda SG105 to mount to the wall, or even under desk/table. remixed to fit the smaller switch, and to use #6 screws.

Pobrania
14
Polubienia
0
Ocena
0
P
PrintablesLukáš Šuba

Mini Rack – Raspberry Pi 4 + TL-SG105

Homelab Mini Rack – Modded Edition This is a remix of the original mini rack case, modified to be more functional and give it a PC case aesthetic. Modifications: Honeycomb front grille with 40mm cable management extension – gives extra…

Pobrania
12
Polubienia
3
Ocena
0
P
PrintablesAljaz_s55al

DIN Rail Mount for Tenda SG105 Network Switch

Description This is a custom DIN rail mount made for the Tenda SG105 network switch. The mount allows the switch to be installed neatly inside an electrical cabinet, control panel, server box or any other DIN rail based setup. It is…

Pobrania
12
Polubienia
0
Ocena
0
P
Printablestownjams

TP-Link TL-SG105 v4 Switch Case

Simple case for v4 of the TL-SG105. Prints without supports. PETG recommended for heat resistance. Features air vents and full access to DC power input and Kensington lock slot. Perfect for mounting the switch with Velcro or similar…

Pobrania
6
Polubienia
0
Ocena
0
P
PrintablescoolestDaniel

TL-SG105 mount

Added speed holes so the internet goes faster

Pobrania
6
Polubienia
0
Ocena
0
P
PrintablesBoxed

SG105 Mount n' Route

SG105 mount with cable hooks to easily route the cables backwards for a cleaner mount. I used an infill modifier for the top side and hooks @ 100% for stronger hooks but it is not required. Turned out quite strong with the modifier.…

Pobrania
5
Polubienia
1
Ocena
0
P
PrintablesDemonik28

TP-Link SG105E V5.0 10" Rack mount with cable holes

This is a remix of the original rack mount that includes: - 0,5mm play on each side to more easily push the switch through - Rails for rubber legs that are included in the newer versions of the switch (v5.0 in my case) - Clip for the rear…

Pobrania
5
Polubienia
1
Ocena
0
P
PrintablesBoxed

SG105 Mount

Simple TP-Link SG105 switch mounting solution. PLA will work fine as these do not get too warm under most conditions. PLA 15% Infill No Supports

Pobrania
4
Polubienia
1
Ocena
0
P
Printablesel_rafa092

TP-LINK SG105/E 10" Rack Mount

10" rack mount for tp link sg 1205/e

Pobrania
4
Polubienia
0
Ocena
0
P
PrintablesHoopy

Skadis mount for TP-Link TL-SG105PE switch (98 x 100 x 25 mm)

Mount your TP-Link TL-SG105PE switch (or any other switch from the army of clones on the market with dimension 98 x 100 x 25 mm) on an Ikea Skadis board. Two M3x8 countersunk screws are needed to screw the bracket to the base plate. You…

Pobrania
4
Polubienia
1
Ocena
0
P
Printablesjimmy_cr

Tenda SG105 gigabit ethernet switch Multiboard (Multibuild) mount

Easily attach and secure Tenda SG105 to Multiboard (Multibuild) grid. horizontal / vertical version securing snaps for vertical version to avoid slide-off Vertical mounting: attach Tenda SG105 onto two pegs, slide it "to the end" snap-in…

Pobrania
3
Polubienia
0
Ocena
0
P
PrintablesCharly

TP-Link Omada 10’’ inch 1U Switch Rack Mount (SG2210P / SG2008 / SG105-M2)

I did not want a server rack cluttered with patch cables that ruin the visual aesthetics of my front panel ! I chose a TP-Link Omada SG2210P switch with the RJ45 ports routed to the rear to maintain a clean design on the front face of my…

Pobrania
3
Polubienia
1
Ocena
0
P
Printablesbroemere

Microlab2 TP-Link TLSG105 Switch Tray Fixed

Fixed the large gap in the original model

Pobrania
1
Polubienia
0
Ocena
0
P
PrintablesJohn Smith

10in rack combo SG105 + Raspberry Pi 3b

Disclaimer : it is flimsy when pushing ethernet cables in. Also the sizing was ... brutish ... You may have to use zip ties to hold the switch in place and need to use threaded inserts for the PI It also uses cheap keystones for whatever…

Pobrania
0
Polubienia
1
Ocena
0
P
Printables

10 inch rack TP-Link SG2210P - SG2008 - SG105-M2

It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…

P
Printables

6.5 inch rack TP-Link OC200 - SG105

Click to Read About 6.5 inch and Rack Frame 6.5 inch Rack Mount Collection It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on…

P
Printables

TP-Link TL-SG105 Diagonal mount

I did this to mount a switch under a table. I recommend printing as shown in the picture (the .3mf file is exactly the same) to minimize the risk of layers peeling off from each other during screwing down.

P
Printables

TP-Link SG1005P | SG105(E) | OC200 7-inch Rack Mount

A 7-inch Rack Mount for the TP-Link SG1005P | SG105(E) | OC200 series. This model is compatible with the GeekPi RackMate TT (Affiliated link). This model is part of a series of 7-inch rack mounts I've designed. You can check out the…

P
Printables

TP-Link TL-SG105 switch mount (screwed+fixed)

My new TL-SG105 doesn't fit the original mount downloaded here. Vendor design changes perhaps? The original mount peg positions are 14.33mm too far from the tab border and are also too big to get through the “+” holes on the switch. What…

P
Printables

TP-Link TL-SG105S-M2 | 5-Port Multi-Gigabit 2.5G Ethernet Switch 10" Rack Mount

Fits that specific model, but may be tweaked for other models as needed via the main files.

P
Printables

SG105 Mount

Simple TP-Link SG105 switch mounting solution. PLA will work fine as these do not get too warm under most conditions. PLA 15% Infill No Supports

P
Printables

TP-Link TL-SG105S-M2 Switch Wall Mount

Remix of DespairFlare's "TP-Link TL-SG105 Wall Mount - Renter Friendly" model for M2 version

P
Printables

10" rack mount Tp-Link SG105 and PI4

Mount for TP-link switch SG105 and PI4 on 5mm standoffs

P
Printables

Mini Rack – Raspberry Pi 4 + TL-SG105

Homelab Mini Rack – Modded Edition This is a remix of the original mini rack case, modified to be more functional and give it a PC case aesthetic. Modifications: Honeycomb front grille with 40mm cable management extension – gives extra…

P
Printables

TP-LINK SG105/E 10" Rack Mount

10" rack mount for tp link sg 1205/e

P
Printables

Tenda SG105 gigabit ethernet switch Multiboard (Multibuild) mount

Easily attach and secure Tenda SG105 to Multiboard (Multibuild) grid. horizontal / vertical version securing snaps for vertical version to avoid slide-off Vertical mounting: attach Tenda SG105 onto two pegs, slide it "to the end" snap-in…

P
Printables

TP-Link TL-SG105 mount

Mount for TP-Link TL-SG105 with cut outs for air vents. Under the mount are two channels for the dc supply cable. Mounting is done with 4mm sink head screws. Print with front facing down.

P
Printables

Montage für lan switch für Nutschine TL-SG105

Montage für lan switch für Nutschine TL-SG105

P
PrintablesIlluSioN

TP-Link Support Rackable for double Switch TL-SG10XXXX / TL-SG105XX

This support allows you to rack a 16 or 24 port switch and a 5 port TP-Link switch on 1U. Ideal if you want to complete your network installation with a small POE switch... Tested with on LEFT : TL-SG1016DE RIGHT : TL-SG105PE TL-SG1005P

Polubienia
2
Ocena
0