348 modeli
This is a housing for: Wemos D1 Mini / ESP8266 ESP-12 0,96" OLED Display I2C SSD1306 CO2: Senseair S8 as well as MH-Z19 is fitting I've soldered a BMP280 and a SHT21 for temperature and humidity together Used DuPont cables Many…
Wydruk około 1,53 €–1,86 € nettoWstępna wycena jednego wariantu
Uchwyt GPS BetaFPV Pavo Pico / Pavo20 / Femto BZ121
Wydruk około 0,14 €–0,17 € nettoWstępna wycena jednego wariantu
The Senosor became too hot on the first model despite the honeycomb on the lid. For this reason, I also had to design the outer wall with honeycomb. Now there is no heat problem in the housing and the sensor measures the content of CO2 in…
Wydruk około 0,38 €–0,47 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a air quality lamp for CO2 metering. I used the design from Lilifee (look at the remix). The original was for the BME680 Sensor. I needed the case for the MH-Z19. So I changed the inner of the case and the "Top"-part. The…
Wydruk około 0,38 €–0,47 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Il existe d'autres modèles à imprimer pour protéger les batteries NP-FZ100, mais celui-ci est une version minimaliste conçu pour protéger juste les contacts, sans prendre trop de place ni de poids. Le couvercle est bien serré sur la…
Wydruk około 0,43 €–0,53 € nettoWstępna wycena jednego wariantu
⚠ Requires additional parts for full functionality, sold separately. 🛠 This model is a remix of IBM's publicly available z17 design, and the additional parts (lid, backplate, powerbutton and stand) are original designs created by me,…
Wydruk około 7,27 €–8,89 € nettoWstępna wycena jednego wariantu
Intro This is an updated and modified version of my previous Workbee dust shoe . The previous version had a wing nut sticking out of the side (which I found a bit annoying although it wasn't hitting the Workbee frame) and the attachment…
Wydruk około 2,88 €–3,52 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I created this to replace one that melted when a bulb was misaligned. I recommend PETG, ASA or something better. It fits the vehicle I made it for just fine. The Oneshape model is linked below, feel free to make it better. Use at your own…
Wydruk około 1,38 €–1,68 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Depending on accuracy of print , feet may require clearancing with rotary tool or engraver to fit over studs.
Wydruk około 9,85 €–12,04 € nettoWstępna wycena dla PETGMateriał u źródła: PET
⚠ Requires additional parts for full functionality, sold separately. 🛠 This model is a remix of IBM's publicly available z16 design, and the additional parts (lid, backplate, powerbutton and stand) are original designs created by me,…
Wydruk około 7,40 €–9,05 € nettoWstępna wycena jednego wariantu
Filament: - JAYO - white - PLA+ Objektgröße: ca. L:B:H in cm Drucker: Prusa MK3S Düse: 0,4 Schichthöhe: 0,2 Infill: 15% Stützen: keine Druckzeit: 15min Der entworfene GU10 Ring für die Deckenbleuchtung, ersetzt den original Haltering.…
Wydruk około 0,23 €–0,28 € nettoWstępna wycena jednego wariantu
⚠ Requires the: Mainframe z17 Modular Case (Free) or Mainframe z16 Modular Case (Free) for full functionality 🔌 Raspberry Pi 5 Extension for the Mainframe z16 and z17 Modular Case This extension pack is designed to make the Mainframe…
Wydruk około 0,06 €–0,07 € nettoWstępna wycena jednego wariantu
I strongly recommend printing the model horizontally to give the snap lock more stability and durability. Feel free to support my work and leave a tip.
ETSY Enhance your ROG Ally gaming experience with this Xbox-style grip designed for the Z1E model. This ergonomic accessory improves comfort during long gaming sessions by providing a familiar controller feel. Perfect for handheld gamers…
Sony NP-FZ100 battery case would be nice if you could post some photos after printing
Transform your ultra-portable Arzopa Z1FC 16.1" 144Hz gaming monitor into a permanent workstation setup! This custom 3D-printed adapter adds standard VESA 100x100mm compatibility , letting you mount it on walls, arms, or stands for…
The NP-FZ100 battery is used in the Sony A9 and A7-RIII. I had previously designed a battery for the A7-RII's batteries - something that was really needed given the rate you go through them. Now with the additional A7-RIII body (and…
This is 4x holder for the Sony NP-FZ100 battery. There is also a 2X version in the files. The lid attaches to the holder with 3x3mm magnets. Also attached are the Fusion 360 files. If the fit is too snug, please modify the current offset…
Very practical battery holder for 2 NP-FZ100 batteries + 2 SD cards and 2 Micro-SD cards. I got the idea from the Sony Facebook Group, but the creator removed the file from thingiverse and it is nowhere found again. As i found the Design…
------------------- Sept 2026 Update ----------------------- Following some helpful feedback, the original models have been marked as "DEPRECATED". The updated versions have an improved fit, and should hold the batteries more securely…
edit: Just added 2 “angle” files which increase the angle back by 7.5 and 10 degrees. I feel this is better than the straight vertical ones I had before but I have left the vertical ones just in case someone else prefers them. I took the…
I've printed vertical ('sony' face on the plate) with support only for the top retention overhang, the small guides on both internal borders can be printed without any support. I tested it with 0.1 layer and with 0.2 layer, 20% infill;…
This is another version of the ROG Ally Z1/Z1E dock port cover (XGm port) with a snug fit so it doesn't accidentally fall out. There is some risk involved so make sure your printer has good calibration for an accurate fit. There are 2…
The idea was to use one per battery. And write on each side if the battery is full or empty. Push the battery from the open side until it snaps in.
Designed for the Makera Z1 with space for additional collets and tools! The main tray includes the following features: 60x bit holders 36x M5 screw holders 18x 4mm dowel pin holders 2x collet holders 4x top clamp holders 2x side clamp…
I made multiple Sony NP-FZ100 Batterieholders for Gridfinity. 1xBatterie 1x1x3U (6U) 2xBatteries 1x2x3U (6U) 4xBatteries 2x2x3U (6U)
Jackie Chan Movie-CZ12: Chinese Zodiac (Ring ; Pencil Topper) 鼠Rat、牛Ox、虎Tiger、兔Rabbit、龙Dragon、蛇Snake、马Horse、羊Goat、猴Monkey、鸡Rooster、狗Dog、猪Pig FB: https://www.facebook.com/3DPPark/ Category: Fashion
Da bei meinem Intex ZX300 Poolsauger nach jeder Saison der Antriebsriemen für die Reinigungsbürste das Zeitliche segnet und man von Intex keinen Ersatz dafür bekommt habe ich mal einen Riemen mit dickerem ‘Rücken’ gezeichnet und in TPU…
Designed to hold 8 Sony A7SII (NP-FZ100) Batteries
I searched far and wide for a replacement throat plate or a 3D model of a throat plate for Ridgid Saw MS1290LZA, to no avail. The model was discontinued. The old plates became brittle and broke apart. This design is much stronger and more…
Sony NP-FZ100 1x2 Gridfinity bin stores 3 Batteries, and stacks when empty.
I modeled this shield after the dimensions for my MSI Z170 Pro Gaming Carbon. It fits perfectly on the board and in the case, but forgot to take a picture. From my search it should work on the Z170A Gaming Pro/Pro Carbon/M3/M5/M6/G45. If…
I have sliced the model in cura and added supports below the notches. Variant 2 has serrations on the sides that were intended to make it a grippy surface to aid removing the cover. But pressing on the side also jams the cover to the…
As a full time photographer I need a lot of batteries but they don't make nice cases to store them all together so I made one. I had 2 needs with this case which are it had to carry 4 batteries and it had to lock closed. I successfully…
Holder für two Sony NP-FZ100 batterys. I printed two in different colors to know which battery is full or empty.
9/29/22: By suggestion from Astroprinter I reworked v15 to redirect some of the cooling air down through the cone to help keep smoke/debris from flowing up around the lens. Update: I've been doing some wood etching and it's become…
Tisk z PLA, PETG, infil 50%.
Test model of a yamaha yz125
BEAR MINI FRAME - Z10 This modification was initially adopted to achieve better results with flexible filaments (using a direct drive extruder) and a stiffer frame for faster printing. Since then, Input Shaper was given as a free upgrade…
Just some basic pieces to fix te machine in place with screws, also a quick focus gauge.
I mostly use the 3D touch probe on the makera Z1, so i designed a probe holder that can hold both the laser height probe, as well as the 3D probe. Be careful when installing the screws, the spindle cover does not have metal inserts, so…
Box na Sony baterie NP-FZ100 dvě varianty pro 6kusů a 12kusů (skládá se z vrch, spodek a 2x latch) Adaptér pro SD 5ks nebo CfA 7ks (zabírá místo jedné baterie) Je potřeba použít M3x30 šroubek na jeden box 6ks (4x latch, 2x pant) Jedná se…
I designed my own version of an air assist nozzle for this laser engraver/cutter. The air pump that I’ve got was a bit of a trade off between power and noise. Therefore I designed the nozzle to minimise air leakage and get the most out of…
stackable gridfinity 1x2x8 holder for two sony fz100 batteries. sd card slot is a bit of a ‘had-some-room-left’ sollution but it is possible to get it out ;)
Technics AEH-AZ100 charging case protective TPU skin
Náhrada originální krabice transformátoru PIKO FZ1 pro modelovou železnici
Belt driven gear, HTD 5, 120 teeth, 20mm hight
Belt holder for sony battery. It is equipped with a fuse, it is very tight. Printable version without supports it is possible to overcome the fuse by force. Version for printing with supports, the fuse must be unlocked before removing the…
Single sided battery protector / cap
Printed with fuzzy skin fuzzy skin thickness 0,1 fuzzy skin point distance 0,1
A remix of a Mainframe z16 model in Fashion scale/Barbie 1:6 size with scaling at 327.84%. Size (HxWxD) approx. 35,6cm x 11,4cm x 22,2cm Remix differences The model is cut into 4 pieces with assembly joints for M3 threaded inserts The…
The Algorithm™ Corporation forbids users from tampering with the device. It has a built-in system that will report to the nearest authorities if it is removed, tampered with, reflashed or reprogrammed. Consume the people that feed you.…
Air quality sensor SEN5x MH-Z19 SSD1327 Hello; I would like to present my take on air quality sensor made out of: ESP32 board SEN55 - PM/NOx/VOC sensor MH-Z19 - CO2 sensor SSD1327 - display Chassis will require : Filaments Geetech marble…
Shorter Gamesir G8+ holder for RRTronics extender. settings: .2mm nozzle
A short front fender for my emtb with 27,5" wheels. Bracket printed in PETG CF, normal PETG should be enough. Mounted to fork with two M3x16 screws(I used cylender hex head DIN 912) and a big washer (~9mm outside diameter). Bracket is…
This is an adapter for a parkside team 12v battery for a Metabo BZ12SP drill. I use this design for the team 12v battery adapter and I have design the adapter the Metabo. It use the genium steel connector of the drill. You must open an…
ROG Z13 got a big XGM slot. I not sure it come with any cover or not because i dont see one. so i made one. I Print it with TPU because it not easy to break . I scare any plastic break inside the slot so I suggest you print with TPU aswell.
This is a new version of my interpretation of the operation of basic logic gates as they could look like in the Zuse Z1 programmable calculator. The information is from pages 216-221 in the book described below. The illustrations are from…
I designed a custom monitor mount for the Arzopa portable monitor, allowing easy attachment to the IKEA SKÅDIS modular pegboard system. This mount provides a secure and adjustable solution for integrating the monitor into a workspace…
Skadis batteryholder for sony camerabattery.
I designed a Z height adjustment for the 10 Watt laser on my Comgrow Comgo Z1 which is more convenient than the original bracket with thumbscrews. Print Settings Printer: CTC Bizer Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm…
This battery dispenser can hold 5 Sony NP-FZ100 batteries. This helps you cycle through your batteries more consistently instead of using the same one over and over. The support structure breaks off very easily. The support structure is a…
Insert USB through top hole, down cable channel and out through hole in arm.
Case for Sony Xperia XZ1 Compact. Disclaimer: I had issues slicing this model with Cura - it seemed to have problems with the thin 0.8 mm walls. Slic3r handled it just fine though. Double checking the layers before printing might still be…
Schrittmotor Kurbel mit Zahnrad D6-SW3-H8-Mod1-Z15 und Schrittmotor Kurbel mit Zahnrad D5-SW3-H8-Mod1-Z15
This is a so you can mount drives in a Zalman Z11 Plus in case you have lost the included parts. You will also need to purchase some #6-32 screws that are 3/8 inch long. You will need four of them per drive. It is recommended to print…
I/O shield for motherboard Z170 Pro Gaming from Asus. Not my model, only reupload. Very nice model so you can use.
Stand for Oclean X/F1/Z1 toothbrushes
Ölfilterschlüssel Z19DTH Vectra C Astra H Meriva Erfolgreich getestet.
I designed this chain guide insert to fit with the stock YZ 125 chain guide aluminum shell. It is almost identical to the stock rubber insert. I can confirm it fits into a 2005 and 2006 stock chain guide. It's designed to be printed as 2…
I wanted to learn how to use Blender and boy what a ride... as I needed some sort of extra protection for my Flow Z13 as there is simply no extra protections for this device other than vinyl decals. Therefore, I went and use a caliper and…
I had a AsRock Z170 Pro4S Motherboard laying around, unfortunately I lost the I/O shield. I modeled this one up as a replacement to finish up the build before I sold the computer. Unfortunately, I didn't take any pictures of it installed…
Extendable to any bitlength (in theory, see README). The Z1 certainly had *some* form of binary counter to control its microprocesses (as described in [Konrad Zuse's Early Computers (Rojas,…
Oil filter wrench for Kawasaki Z1000 2010 oil filter. Fits for HF303 Hiflow and original Kawasaki oil filter. Ratchet 1/2in. Category: Hand Tools
90 degree vacuum adapter for the Makera Z1 CNC machine. Perfect to attach your shop vac.
I designed this to replace the stock lower chain roller on my 2005 YZ 125. Printed 100% infill in TPU. Just insert your 608 bearings and you're good to go.
Changed a housing for NodeMCU V2, DHT22 and MH-Z19B to hold the MH-Z19B and a Wemos D1 mini. Removed all holes for screws since the lid clips in now. There is also space to add a single WS2812B led above the Wemos. The Wemos clips in but…
Print standing upright and glue two half's together. Do a less messy glue job then I did. ;-) Orca slicer fuzzy skin settings use 0.3/0.3
Remix this to give more strength to the part. Thin parts will bend and for small increments the axis will not move, for example z-hop. Rocksolid part now. Need longer screws and an ajustable motor mount like:…
Wahoo adapter for the Z1 Cycplus mount, pretty inexpensive and easy to find in AliExpress or similar webpages. I also increased the height so the Wahoo doesn't touch the mount when mounting it. You will need M3 heated inserts for…
Instantly boost your COBOL skills and save the department of labor by turning your Raspberry Pi 3 into a mainframe!! Show all your fellow cobalt-colleagues what you are made of by hacking directly into the mainframe from home. Do not…
transition batery parkside X20V to drill Metabo BZ12SP print: pla in the future I will also complete the project
Super simple battery holder for up to 4 Sony NP-FZ100 Batteries.
Suports: yes
Holds four, Sony NP-FZ100 batteries with a snug enough fit to hold batteries securely while in a backpack. To remove a battery, just give it a little push from the hole in the 'bottom' side. I like to keep the fully charged batteries with…
Protective case for the Sony NP-FZ100 battery. No support is required for printing.
I printed as oriented without supports. 3 walls, 10% gyroid. I intentionally designed it in a way where the bottom screw is a little tricky to install. (Leaving more structure at a thing point.) It needs to be placed into the lower probe…
I made these to have the faders more visually present in the dark. Therefore, I printed the faders with GlowInTheDark PLA Filament. The mounting holes on the bottom side took some experimenting before they exactly fit the Z1 faders. If…
This is a gridfinity storage caddy for the Makera Z1 accessories, including: 5 pins 1 collet wrench 4 top clamps 2 toe clamps 2 collet adapters 2 6mm to 1/8" adapters 15 fixture screws. There is a version without the text for the collet…
The Ricoh Theta Z1 camera has 2 problems, that can be solved using this model: The camera can not stand on its own if you want to use the USB-C port (e.g. for 360-Livestreaming) When using a tripod, the USB-C port is covered by most…
GUIDE https://www.instructables.com/Z100s-3D-Printed-Symmetric-Wireless-Mouse-Guide/ VIDEO GUIDE: https://youtu.be/o0P37Avcor0 -60g with AAA. Mass will vary based on battery and print material. -Wireless using G305 Internals -Rechargeable…
I would suggest printing it up right beacause that way, the plastic is sturdier and can whitstand the bending better. Also use 3 walls so the clip doesn't contain any infill. This remix is using the Oclean wall holder by Marcus24 as well…
Hello Two different feet for the Traktor Kontrol X1/F1/Z1 mk2 version of DJ controllers. One to make it flush with a controller, for example the S4 mk3. But you either need to add the rubber feet or use the step files and increase the…
Two versions: One with 4 tool holders and one without. This bin includes a spot for the two locating pins, three M4x10 screws, and 2 tightening wrenches. I have included a fourth hole for a screw so that there is a place to put the screws…
I only made this case, original build instructions are here https://emariete.com/en/meter-co2-gadget/
I recently bought a Beeline navigation device for my motorcycle. The mounting option for my type of motorcycle were either limited location wise, or bulky and ugly otherwise. So I decided to create my own option. In the cockpit attached…
Designed for to delete the rear fender of a 2021 Kawasaki Z125 Pro, I just used some 2 part epoxy to put the 2 pieces together, Re-use stock hardware Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Infill: 100%…
An N-scale car, designed with a well for the camera to sit in, so that it'll better fit in tunnels or other low-clearance spaces. Designed to hold the Sony HDR-AZ1 action cam. Video of car/camera in action:…
Air Assist for a Comgow Z1 10W Laser. Fits on the original Housing. You need: 1x V6 Nozzle drilled to 1.5mm 1x KJH04-M6 2x M3 Screw 8-10mm Edding to darken the V6 nozzle. Works very fine.
![[WORK IN PROGRESS] Mini Brake Stand / Mini Brembo Z18 for Mini Wheels](https://media.printables.com/media/prints/371322/images/3128148_7a32e244-fb8e-485a-aa52-3109f892af8f/bremsooooo.jpg)
