120 modeli
A 49mm lens cap that I made. Works great with my Sony lenses. Be careful to use this lenscap with too rounded lenses as the backside of this lens cap is flat for easier printing. I made a lite version, see "49mm_lenscap_V3_lite.stl" which…
The Donut Espresso Shaker is an espresso shaker that enables even distribution when preparing espresso for a wide range of portafilter sizes. What makes the Donut Shaker special is that it achieves this result with any portafilter size…
A lens hood for your 50mm lens (filter diameter 49mm). No thread - just push on. Use the Fuzzy Skin option in PrusaSlicer if you wish. No support required. Paint the interior matte black. Do you like it? Please consider to buy me a cup…
A simple filter to adapt 49mm lens filter to 52mm lenses. Threads are 49x0.75 and 52x0.75. Avoid tightening the filters too much, it might be difficult to remove after (remove the 49mm filter first). Print at 0.1mm layer height for best…
Hey there :) Step 1: Load the files into the slicer Or you use the prepared gcode, just look at the requirements Step 2: Correct the orientation of the models: The FRAME is printed with the Logo facing down and the bridging should be from…
Printable without supports.
This is designed to replace a broken Sony 49mm lens cap but may be able fit other lens with the same diameter, as long as the lens curvature is fairly flat. This can be printed as one piece with a fair amount of bridging, or as two pieces…
I wanted a thin lens cap for my Fujifilm X100 that has a lens hood so I can put it into a case I bought easier without stretching the case so much. I imagine it would work for other cameras that accept a 49mm filter thread as well.
A simple filter to adapt 49mm lens filter to 55mm lenses. Threads are 49x0.75 and 55x0.75. Avoid tightening the filters too much, it might be difficult to remove after (remove the 49mm filter first or use the handle version). Print at…
I designed this step-down-ring to be able to attach a ø49mm variable ND filter to my vintage 50mm Minolta lens with a ø55mm filter thread. Attaching this setup to an APS-C camera does not cause any vignetting.
A self leveling tamping station designed for the 49mm basket of a pre-millenium (generation 2) La Pavoni Lever Espresso machine. The basket sits flat in the base and the funnel screws on top. The funnel was designed with a straight…
This adapter will allow you to use your 49mm or 52 mm filter on a Hasselblad lens, having a B50 bayonet. In addition, you can still use the original lens hood without interference. Print instructions Category: Camera Print Settings…
The tolerances should allow it to be used with needles that have the metal or the rubber handle. With needles that have a <20mm handle and a needle length of 40mm (without the handle) there is no need to cut the needles. The files contain…
This is a relatively low profile 49mm filter thread adapter for the OM System TG-7 and other Olympus Tough cameras. This lets you use the same filter size as you might use on a Ricoh GRIII, which can also use the same batteries……
49mm lens cap with flaps for easy screw and unscrew.
I bought the kit with the telezoom lens. So I needed a lens cap holder for both 40.5mm and 49mm. I could not find a solution so I created this. Print instructions Category: Sport & Outdoors Summary I bought the kit with the telezoom lens.…
This is a low profile 49mm threaded compact lens hood/shade with a few versions. I recommend printing at 0.10mm layer height in PLA for best results with the threads, but it should be fine at 0.15 too. Fuzzy skin modifier makes it look…
I got an action cam for the motor bike, but the mounts that came with the cam doesn't fit very well at the bike and to be honest I do not trust them. So I created some new mounts for the action cam. I think the holder should be identical…
Fuji X100V / X100VI camera filter adapter 49mm - angular version II Model is designed from scratch using BoltFactory Blender plugin. Adapter outer walls are tilted to the same angle the stock lens has, so it better fits overall style of…
Using same needles and same countersunk bolts. Trim needle handle to 7mm and add 20 and 30mm for the actual needle. No mods beside needle positions to make them work when scaled. Will work with standard 49mm Pre Mil La Pavoni and IMS…
UPDATE [2024-04-26] : Designed improved adapter angular version II 49mm adapter ring for Fujifilm X100 series cameras. UPDATE 01-02-2024: Added V2 with more smooth walls. Remixed the source adapter by doubling its 49mm thread to other…
This Lens cap is designed to be printed without supports at 0.15mm layerheight and has some tight tolerances so the locking mechanism most likely has to be broken loose wich is best done by carefully bending the parts in different…
Threaded two part filament guide designed to pass through the top of an IKEA Lack table. Simply use a 1 inch hole saw to drill the hole for it to pass through, I had to shave the hole in the table a little bit with an exacto to make it…
This is a magentic lens filter case for 49mm Filter. Customized version of https://www.thingiverse.com/thing:43781 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=43781 All credits got to:…
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/lakqtHH3Esh Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Yes Supports: No Resolution: .16 Infill: 20 Filament: eSun PETG Black…
This is a remix of a very good model, I had to adjust it a little to work for my 49mm lens element cap. Many thanks
lens cap for a 49mm diameter lens Printable in 4 pieces in any material
This adapter ring works with standard camera filter threads (~0.5mm depth, 0.7mm pitch). It adapts smaller diameter filters to work with larger diameter threads. The thickness is as low as possible to reduce optical problems. Since there…
A clip to hold your 49mm/67mm lens cap, for your camera backpack strap, jacket, belt or pocket. I edited the lens cap buckle to be more minimalist and compact, and combined with the clip to be printed on its edge without supports.…
49mm to 52mm filter adapter for Fuji X100V / X100VI camera - angular version II This model is allowing to use more common 52mm filters on Fuji X100 series cameras. Model is designed from scratch using BoltFactory Blender plugin. Adapter…
Low profile 49mm to 58mm step up ring with tabs for leverage. Printed for use with Helios 44-2 or any other 49mm filter size lens. Standard lens m.75 thread pitch.
This lens holder is designed specifically for the Olympus XA rangefinder camera. It accommodates a 43mm filter, which minimally obstructs the lower portion of the viewfinder, ensuring accurate framing while taking photos. The design…
Tool mount for a 65mm VFD spindle
Dose zum schrauben für Fotofilter mit 49 mm Durchmesser. Die Dose hat innen einen Durchmesser von 52 mm und eine freie Höhe von 12 mm. Eventuell innen mit Schaumgummi oder Velour auskleiden damit der Filter nicht klappert. Gedruckt mit…
Migrating from thingiverse https://www.thingiverse.com/thing:4362313 Original here https://www.thingiverse.com/thing:3797754 Added the retaining tab to prevent it from sliding out. happens when trowing large amount of water. especially…
This is a replacement spring for a Minolta 49mm lens cap as found on my Maxxum Lenses. This will replace a broken spring and should be printed with 100% infill and in PETG for the flexibility. I've tested this in a Maxxum 35-70mm Lens as…
A simple funnel for 49mm baskets that are used by the Olympia Cremina or older La Pavoni models. The funnel sits well on my 14g baskets without the need for magnets. It allows for WDT and tamping for minimal mess in the kitchen :) Printed…
Hello :) Today I have a new 3D model for you. I made a lens cover cap because I didn't like the alternatives here and some of them didn't offer a secure hold of the lens cover. This lens cover fits the most common covers with a diameter…
Thread with a layer height of 0.1 mm
Canon M50 Stock Len's Cap holder for Stock Lens 15-45mm. Will not drop or lost your Len's cap again! Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 80 Filament: Any PLA Brand…
External thread: M49x0,75 Internal thread: M52x0,75 Tested with basic PLA, no support, 0,4mm nozzle, 0,2mm layers
A lens hood for 49mm lenses. Tested on Minolta DiMage 7i but may be compatible with additional models (and brands) using 49mm lens.
49mm to 52mm filter adapter for Fuji X100V / X100VI camera - angular version II This model is allowing to use more common 52mm filters on Fujifilm X70 cameras. Model is designed from scratch using BoltFactory Blender plugin. Adapter is…
Originally posted by rzschokke on Thingiverse: Use this to adapt a 44mm, 12 spline bottom bracket socket tool (such as Park Tool BBT-79) to a 48.5mm bottom bracket. I already owned a BBT-79, but when I replaced my SRAM DUB BB with…
Adapter which uses a PVS-14 eyecup retainer ring to mount to camera objectives which use standard 49mm filter threads, such as the Canon EF-M 15-45
50T Gear for a Nitro car spur gear
I printed it with 250mm/s and a 0.3layer
Basic watch strap holder for my 49mm Apple Watch Ultra 2. Compatible with the titanium watch band from Nomad as well. It has one centered hole for a screw to mount it to the wall. I'll add a hidden screw mountain in the next version.
When I got my camera, it came with a lens cap, but only half a clip. I used that clip and reproduced a complete clip that would grab onto the 49mm Rokkor lens thread, and matched the styling of the original clip. Printing recommendations:…
Fuji X70 camera filter adapter 49mm - angular version II 7mm Model is designed from scratch using BoltFactory Blender plugin. Adapter is 7mm long to support full range of close up focusing. Tight fit is sealing lens front from any dust…
Multiple size bins I printed for Full Box stackable 4x4 of 36 base. Bins have 7 h 49mm interior height. The two boxes can be found here: https://www.printables.com/model/1288433-full-stackable-gridfinity-box-18x13cm…
Custom coffee grounds funnel to fit 49mm Portafilter. Measured to fit the pre millennial 49mm La Pavoni Europiccola portafilter. From 49mm to 67mm diameter funnel.
Very simple tamper base station for the 49mm & 51mm naked-portafilter for Olympia Cremina and La Pavoni. It has just enough height to clear the portafilter handle from the ground and keeps it level even when not filled. Now parametric…
Fully tested with Flektogons 35 and Takumars 35, 28 on fullframe sensor, no vignettes, good hood coverage. Threadless, fit tight and possible to lock in position with extra screw+ metal shim. Printer setting: PETG, Supports none, solid…
A small slip-on adapter to mount 49mm ND filters on the back of ISCO 90 f2 and 120 f2 lenses. Best to be printed with 0.1mm layerheight or in SLA.
New base for the portafilter from naked-portafilter.com for the 49mm La Pavoni or Olympia Cremina. I use it with the 14g precision basket with 22mm depth. I needed to cut the needles to a total of 40/50mm. Printed with PETG on Bambulab A1…
You might want to scale this a percent or two. It's quite a tight fit for my filter holder. The inside diameter is 52.2mm
This is a 49mm tamper that I created for my 58 to 49mm step-down basket. It will probably fit other 49mm baskets as well. Pinted in PLA, 0.2 layer height, Structural and default setting. The example shown in the pictures has a height…
This is a replacement for whatever you call the bit that sits inside these late-era Minolta lens caps. This cap came from an MD-mount 28mm f/2.8 from the X-700 era, and the sprung plastic had predictably failed. This cap is a 49mm one,…
Dosing funnel for the Alikisscafe 58mm to 49mm step down filter basket from AliExpress: https://www.aliexpress.com/item/1005010153373261.html Two versions uploaded: with magnet holes to fit 8x 4 by 1.5mm magnets without magnet holes I've…
Remove 49mm filter from it's metal ring and glue it to the model. Glue in 4x1.6 magnets in the holes. Uploaded a revision, easier to hold with tweezers and larger opening for filter. Magnets should "clip" in place, but will still need to…
Simple adapter ring to mount glass from B+W 49mm XS-Pro slim UV filter under the front nameplate of Voigtlander 35mm F0.9 Nokton lens in Fuji X mount Steps: Soften factory glue by dropping few drops of acetone into front filter thread…
A pinch mounting ring for mounting a threaded lens filter onto a lens with no threaded rim. This adaptor is specifically designed for a 49mm filter to mount onto a Sony DSC-H300, which has a 2" OD lens. Printed with tree supports because…
Leveler for the Nomcore tamper on a Sworks step-down basket. Printed in ASA for heat protection, but can be done in PETG. Tolerances might be different for other materials because of different shrink rates. Created with Onshape, you can…
These are numbered bases (1 through 4) for table top gaming minis with 29mm / 2" round bases. They come in very handy for DMs when managing a roomful of trolls. Any more than that, and your DM is being a jerk. Category: Games
After purchasing the stepdown basket, I've forgot to order the baffle (black piece that sits on the edge of the basket to align horizontally), to adapt my 58mm Normcore tamper. So because of that I've designed the baffle based on the…
Overview This is a clean, functional adapter ring (grommet/spacer) designed to fit patio tables with a 49mm mounting hole, adapting it down to fit standard 44mm umbrella poles. It keeps the umbrella securely centered, prevents annoying…
Got an order for clamps to use while dissassembling motorcycle struts on a vice. These are simple but work. Print them heavy if you plan to use the more than once.
Minimal container for any use in misure 132 x 70 x 49mm
Made this basic corner shelf for storing my spices. To Print Sturdy Recommend PETG .20mm Structural Profile at least 4 walls at least 25% Gyroid Infill
Support présentoir Médaille du Travail 49mm x 70mm modèle bicolore pour les 15 et 20 ans
Check to make sure the model has the two holes mentioned. (OrcaSlicer gave an error that it didn't include boolean meshes, but opening the exported STL shows it as expected.) If someone remixes the handle void to hold it more elegantly,…
As you can see in the photos, the original part was broken. I couldn’t find a suitable spare part, nor any existing 3D model for printing, so I designed and made this adapter myself. The Nevada vacuum cleaner I made this for is quite old,…
This is a remix of Kirils Deep 55mm lens cap . The only thing I've done is scale the model by 89% so that it fits lenses that use 49mm diameter caps. I printed mine out of ASA with a 0.1mm layer height.
The original was designed for 1.8" screens that were about 53mm total diameter. This one fits badges that are 1.5" screen with sound and 49mm diameter. Uses the same blank plate as the original print.
🟩 🟦 🟦 🟪 🟥 🟧 🟨 I bought this camera for almost nothing, as I thought it might be nice to fix the broken flash and use it a bit, then maybe sell it on with a bundle of film. The camera still needs the lens fog clearing (I'm on it, but have…
A slim, one-piece screw-in lens cap designed for the Minolta MD 50mm f/1.7 . No springs, clips or assembly – just screw it into the lens’s 49mm filter thread. The extended textured rim makes the cap easier to grip when attaching and…
Check to make sure the model has the two holes mentioned. (OrcaSlicer gave an error that it didn't include boolean meshes, but opening the exported STL shows it as expected.) If someone remixes the handle void to hold it more elegantly,…
This is a replacement for whatever you call the bit that sits inside these late-era Minolta lens caps. This cap came from an MD-mount 28mm f/2.8 from the X-700 era, and the sprung plastic had predictably failed. This cap is a 49mm one,…
When I got my camera, it came with a lens cap, but only half a clip. I used that clip and reproduced a complete clip that would grab onto the 49mm Rokkor lens thread, and matched the styling of the original clip. Printing recommendations:…
As you can see in the photos, the original part was broken. I couldn’t find a suitable spare part, nor any existing 3D model for printing, so I designed and made this adapter myself. The Nevada vacuum cleaner I made this for is quite old,…
A simple insert cover, where the spinner has a 49mm diameter. Just plug it in the spinner hole and job done. Slightly over an hour to print and I used PLA+ 2.0, but I would of thought PLA would suffice. The true test will be when the lawn…
Got an order for clamps to use while dissassembling motorcycle struts on a vice. These are simple but work. Print them heavy if you plan to use the more than once.
Made this basic corner shelf for storing my spices. To Print Sturdy Recommend PETG .20mm Structural Profile at least 4 walls at least 25% Gyroid Infill
The Donut Espresso Shaker is an espresso shaker that enables even distribution when preparing espresso for a wide range of portafilter sizes. What makes the Donut Shaker special is that it achieves this result with any portafilter size…
The hinge is held together with a steel wire and the end covers superglued on.
A 49mm filter adapter designed to press onto the lens of a Polaroid Model 80, 80A or 80B, remixed from Hackaninstant's Packfilm filter. It has been tested on both an 80 and 80B for an upcoming project of mine. Print Settings Printer…
When using an automatic lens without it's camera, it is useful to use an aperture ring to ‘stop’ the lens down. In this model, I took a step down ring and imported the STL into Shapr3D. I then closed off the top of the lens and created an…
A handy ring that adapts 43mm, 46mm and 49mm threads down (or up) to 39mm, designed to fit the Alum Panomicron setup. It prints well with a 0.4mm nozzle at 0.12mm layer height, providing clean threads and a snug fit. Ideal for switching…
Lens cap with a rim on the bottom to fit lens that has it's middle part flush with the filter thread. Remix of @MMichigan_315563's model.
Basic but functional fork seal driver for 49mm fork tube found on Harley touring models. Design is 2 parts the driver body that has a hollowed upper section to fill with media to add weight. I used steel sand blasting media then glued the…
K&F Concept Nano-D Filter 49mm Holder for iPhone 16 pro
This is for a 49mm portafilter off of a Pre-Millenium La Pavoni Europiccola. I hung it to the wall with some double-sided tape or command strips. Simple and effective.
Remove 49mm filter from it's metal ring and glue it to the model. Glue in 4x1.6 magnets in the holes. Uploaded a revision, easier to hold with tweezers and larger opening for filter. Magnets should "clip" in place, but will still need to…
