Liczymy pasujące modele…
A simple and clean iPod touch case. The case was designed for the 7th generation iPod touch but but will also work with generations 5 and 6 as the dimensions are the same. Printed in PLA with no supports.
Wydruk około 0,92 €–1,13 € nettoWstępna wycena jednego wariantu
Give your fingers a break while one handing your Kindle.
Wydruk około 0,89 €–1,08 € nettoWstępna wycena jednego wariantu
This is a 2-part Ipad case I designed to fit the 10.2-inch Ipad 7th generation device. I designed this in Fusion 360 and this is my first time using the program. The model is untested but was built using a scale model of the iPad. I…
A stand for an ipad 7th generation at a slope of 15 degrees for writing or drawing on it. Has a pen holder of diameter 10mm. Is printed in 2 halves so that it can fit on most print beds, tolerance of 0.12 mm on the slots so should fit…
I wanted to lower the fan noise of my intel NUC and had a Noctua NF-A9x14 PWM lying around. I thought obout replacing the top lid of the NUC by this one and mounting the NF-A9x14 to my lid. I hoped to be able to disable (/remove) the…
Minimalist stand for Kindle fire 7", 7th generation. It will either snap or slide over the body. The stand folds down flat, so it's easy to slide under a pillow. The kick-stand is connected to the holder body via friction.There's little…
Material-efficient dividers for 7th Continent. This was made using the Board Game Insert Toolkit ( https://github.com/IdoMagal/The-Boardgame-Insert-Toolkit ) Category: Games
For my nieces 7th birthday, I designed some extra decorations to fit the Brick Frame by LoryP. She loved it! Print Instructions PLA, 0,4 nozzle 0,2mm layer 15% infill Macaron needs supports and 2 color changes (top-bottom/cream filling)…
its print in place print it with a brim you should print it in pla or petg not tpu
I modified the original plate design, to delete the 7th and reverse gear when not needed. You just have to unscrew the top cover of the Simsonn HS-Pro to change the plate. Link to the product page:…
Intel NUC 7 Thin modell - 19-Inch Rackmount 3 walls 20% infill PETG (for heat resistance) Print face down Parts 5x M5 hex nuts 5x M5 screws
A 3D figure of a fictional fighter. I got inspired by the Russian Sukhoi Flanker Series of Aircrafts. It is supposed to
For my nieces 7th birthday, I designed some extra decorations to fit the Brick Frame by LoryP. She loved it! Print Instructions PLA, 0,4 nozzle 0,2mm layer 15% infill Macaron needs supports and 2 color changes (top-bottom/cream filling)…
I made this Wallmount for the iPad 7th gen. Should also fit 8th and 9th gen I made the fitment a bit tight so nobody could just pull it out. (still possible with force but be careful)
I hated the adds on my Kindle for books that weren't related to anything I was reading. I definitly didn't need the romance novel adds popping up on my kindle at work. I wanted a case that covered the devise screen and stayed closed, but…
Light version of my original card box for 7th Continent. Print like the .stl is. NOT FOR COMMERCIAL USE !! MERCI DE NE PAS FAIRE COMMERCE DE MES CREATIONS, si on vous propose de vous vendre une de mes création, merci de me prévenir.
I've never printed and tested this mod It's Tray for player and equipment for the boardgame 7th Continent. For equipment tray, the main equipment goes to the top and you add the associated equipment underneath. If you put the bag, you can…
It's not super tight, so you might want to scale it down a tiny bit. Two screws should be sufficient to hold the tablet, pick holes as needed :) OpenSCAD file included if you want to adjust hole sizes etc.
This is a remix of original model from sbellon_9461 Added a cutout to the model that was created for the 7th Continent. This cutout allows players of the 7th Citadel ability to see keywords on bottom left of the card, while being able to…
Try this as a smoother, less broken-up version: 20 cm x 20 cm Print Bed Version This is a modified version of the subwoofer enclosure, split into smaller parts so it can be printed on 20 cm x 20 cm print beds. I added connectors to make…
This custom-designed Kindle 7th Gen case is a dual-layer protective solution, combining a flexible TPU inner shell with a rigid PLA outer cover. The inner TPU layer securely holds the device, absorbing shocks, while the PLA booklet-style…
Slim wall mount for Amazon FireHD8 7th gen., which I use as my smart home control panel. room for angular USB connector and hole for cable hole for access to power button bottom openings for speakers wall mounted base plate and face are…
Greetings to those who have gone before.
Kindle Paperwhite 7th Gen case / Kindle Paperwhite 7. Generation Hülle Added honeycomb structure to the back. Cheers to junaling for the original model! Pictures: printed in Anycubic PLA blue on textured print sheet
AMS is optional : the logo is slightly engraved, so it will be visible, though barely. The lid sits pretty tight , especially at first, but with time and usage the pressure becomes optimal. There are slots for 5x2 mm magnets, which I…
This is a model of Ninidazir's Citadel for use in the board game 7th Citadel. The design is based off of illustrations from the game materials. Two versions are provided - a complete model, and one in which the garden is a separate piece…
A set of 3D-printable dividers designed for The 7th Citadel board game, optimized for fast printing. These dividers help organize Adventure cards efficiently while integrating seamlessly with the game's original storage solution. Key…
This is flag pole holder, originating from a use case of the 17th May national day in Norway. It fits the usual small kids-flags and a pole of 60mm. It's easy and quick to fix with some cable binders. We used it to decorate a couple of…
You can find in the provided file a multicolor RAW 3MF file, a multicolor Prusa XL 3MF file, a multicolor Bambu X1C 3MF file and a monocolor STL file. Feel free to remix, I have a lot of idea to transform this model in more useful object,…
Before you go further! This model is available for free for all my supporters in Printables Club 🧡 Consider joining my club to have access to all ⭐⭐⭐ exclusive projects ⭐⭐⭐ and be part of my community! This project is for personal use…
I have an iPod Nano 7th gen and i have nowhere to put it. So i created this little holder so it wont get scratches and dents if it falls and i dont have it secured!
Robot vaccum brush hair cutter date long ago in 17th. century and now you can cut it with style like people are cutting in 17th-18th. century :) :) simple print petg 50% infill enjoy
Unit patch for the 7th Transportation Brigade. 1 inch tall and 2 mm thick. Image of the actual patch for color matching. Load the STL and “Split to Parts” to apply colors. The 3MF file is already painted and will produce 2 each of 1 inch…
Summary The 7th stellation of a icosahedron. It's an inspirational mix of playing around with the 1st stellation and recent experimentation with thin sheet foldable designs. A design was chosen that had points made of an even number of…
I found a project online that utilises old Kindles as weather displays. I will link the project below. In order to make it look a little neater I designed a case/stand for the Kindle. I have 2 old Kindles & the project works on both, but…
This has been my favourite ever 3D design. Macro Deck is a brilliant app that repurposes portable devices running either IOS or Android. You install the client app on your portable device, in my case an Amazon Fire HD8 (7th gen) . The PC…
The example was printed with the following settings on a Centauri Carbon: Sparse Infill Density = 8% Apply fill gap = Top and bottom only Prime tower enabled Flush into support Filament Change at 22 No brim
Replacement plate for a Simsonn 7 speed shifter that blocks off 7th and makes it harder to misshift into reverse. The stock top plate also lets the shifter rod slam into the PCB during use, this should stop you from damaging the PCB while…
AAC Keyguard files for 1st through 7th Generation Ipad Minis This listing will include all the keyguards I have designed for iPad Minis if you are looking for iPad, Air, Pro, Pro 12.9 please look at my profile for other listings. Most of…
Printed with 0.25 mm nozzle, 0.1 mm layer height. Change the filament in correct layers to achieve the multi-color effect.
Printing the hilarious wheellock nerf blaster by CARNYREX I wanted to complete the accesory by a matching powder flask - only to find no suitable model at all (are all pirate/highwaymen/musketeer cosplayers using original ones, or just…
Kleiderhaken Boykott seit dem 27.02.2022 NORDSTREAM 2 ist in meinem Haus geschlossen ! Dies ist ein Modell meiner Gas-Hauptleitung die unabhängig von politischen “Entscheidungsträgern” seit dem 27.02.2022 geschlossen ist. Ich hoffe, dass…
The Iconic swept hilt Rapier. In the early 17th century, this is your sidearm. Fast, and good on the battlefield. One handed, ideal for dueling, and looks great. Category: Props
3D model description Frame for Thin or Thick Model iPod models from 2005-2013 (5th 5.5 6th &7th Gen) included. YOU WILL NEED: 4x M3x16 or M3x17mm Screws (Thin) 4x M3x19mm or M3x20mm Screws (Thick) 4xm3 Nuts (acorn nuts give a finished…
1980 - 1986 Ford F-150 7th Generation Wall art Bullnose
its print in place print it with a brim you should print it in pla or petg not tpu
I modified the original plate design, to delete the 7th and reverse gear when not needed. You just have to unscrew the top cover of the Simsonn HS-Pro to change the plate. Link to the product page:…
Intel NUC 7 Thin modell - 19-Inch Rackmount 3 walls 20% infill PETG (for heat resistance) Print face down Parts 5x M5 hex nuts 5x M5 screws
I made this to fit a BOSS single din radio (616UAB) into my 1982 Ford F-250, I had a plastic insert in the truck that allowed for 4 sheet metal screws in each corner for fasten the panel into place. Hopefully someone else has a need for…
A 3D figure of a fictional fighter. I got inspired by the Russian Sukhoi Flanker Series of Aircrafts. It is supposed to
A handy little case to customize the style of and protect your IPod nano 7th Gen! Print one CASE, and one of each button, VOLUME and POWER. Printing Use slicer to add color/designs to the back of the case. The case should be printed in…
Changelog: 5/12/26 - Base has been updated to be a hollow shell, and the VESA Hinge has some added ribbing A VESA mounted bracket and stand for an iPad 7th gen tablet. The iPad latches into place with an over center latch and the bracket…
Today I had an F650 come into the shop that was missing the lower 2 license plate clips, decided to design and print some up when I was on lunch using a factory clip as a reference. I designed the 5mm hole one originally because I wasn't…
Suitable replacement. Original disintegrated. Did not model upper locking feature. Glue on install to vehicle frame. Recommend a removable adhesive (urethane, B-1/2, etc...). Print with clip standing on its narrowest edge (most vertical…
A fidget spinner in the shape of March 7th's brooch. The spinner uses standard 608 bearings (8mm ID x 22mm OD x 7mm Thickness). This is intended to be printed on a single-extruder printer without supports in multiple parts. The brooch is…
Magnet model of the US Air Force 57th Wing patch. Designed to fit small 6mm x 3mm magnets. Base layer should start as a dark grey, I used Overture Space Gray in my photos. Red on patch is painted with red acrylic paint. G-Code has…
This is a remix of the excellent 7th Continent Storage Solution by turbo_gecko - https://www.thingiverse.com/thing:3708123 . This fits all current content for 7th Continent. I wanted the boxes to have better lids and I didn't need them to…
Kindle Fire 7 (7th Gen - 2017) Wall/Switch mount. This was made to mount a kindle fire over a 3-gang wall-switch, with the switches still being available from below if needed. I wanted to stop the kids/wife from turning off smart bulbs at…
Remix of https://www.thingiverse.com/thing:2773222 by thatdude902 Loved their design but wanted it to be the full length of the tablet. I split the part in Solidworks, added the extra length to cover the full length of the tablet, then…
Works seamlessly with Scottyujan design, requiring glue to connect the two parts securely. Achieves a perfect fit with both iPad 7th and 9th gen models.Experience a sleek and functional design that complements your iPad seamlessly.…
I made a charging dock for my daughter's 7th generation iPod Nano. I glued the lighting cable into place. The flat surface is for embossing a name. Printed in PETG 0.15mm height. Shouldn't need supports.
This STONE PUMP BUILDING is printed as a single unit. It will take 7+ hours to print, but the wait is a very satisfying model for your layout. It is printed with Prusament PLA. Print the main structure in the color filament that…
This OLD LITTLE CHURCH will take many hours to print, but the wait is a very satisfying model for your layout. It is printed with Prusament PLA. If you plan to light the model make sure you paint the inside black so the walls do not glow.…
This HO scale RETRO-TRUSS BRIDGE is a combination of a Walthers Cornerstone Modernized Double-Track Truss Bridge kit (#933-4510) and 3D printed open structure trusses. Use the Walthers truss sides as a template for cutting and mitering…
This little STONE/ROCK PEDESTRIAN BRIDGE is scalable within reason. Print it black or dark grey and then paint multi-colored rocks. I exclusively print with PLA and have found that ordinary clear lacquer thinner (Nail polish remover) is a…
This HO scale (1/87th) SHANTY SHED is under construction. Depending on your printer, some components may require some minimum minor trimming. I exclusively print with PLA and have found that ordinary clear lacquer thinner (Nail polish…
This HO scale (1/87th) VICTORIAN MANSION is to look like it is under construction. The model at this posting is for the first floor only. Depending on your printer, some components may require some minimum minor trimming. Commercially…
This is the second floor of the VICTORIAN MANSION model. Depending on your printer, some components may require some minimum minor trimming. Commercially produced 4'x8' plywood flooring wasn't produced in this country until 1927. So the…
This is the attic floor of the VICTORIAN MANSION model. Depending on your printer, some components may require some minimum minor trimming. Commercially produced 4'x8' plywood flooring wasn't produced in this country until 1927. So the…
This is the roof rafters of the VICTORIAN MANSION model. Depending on your printer, some components may require some minimum minor trimming. I exclusively print with PLA and have found that ordinary clear lacquer thinner (Nail polish…
Back to weird old art but this time a bit later and much better art. This piece is based on this drawing by Jacopo Ligozzi drawn some time between 1590 and 1610 . I would like to see how this prints on a decent printer as my Anet A8 can't…
Cake topper that you can print for your friend's passing driving test celebration. Printed from PLA but I recomend PET (food safe) if you really plan to put this in a cake (i don't cause my Jennifer didn't pass again on 7th time, but…
A 17th century goblet fragment foun at Rathfarnham Castle, Dublin http://irisharchaeology.ie/2014/11/lost-and-found-excavations-at-rathfarnham-castle-dublin/ Fragment was scanned than based on shape and known design at the time rebuilt as…
⚫ Sonic Screwdriver 7th Doctor ⚫ It's finally here. Another sonic screwdriver this time from the Seventh Doctor. More sonic screwdrivers coming soon! ➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖ Follow me on YouTube for more info about what you can look forward for.…
We Dutch are known for our tulip flowers. But what not many people know is that special vases were designed for tulips as early as the 17th century. You can read more about the tulip vase on Wikipedia. I designed this tulip vase to be…
Intel NUC Rackmount Kit for 10" server cabinets. The NUC is attached to the cage using two VESA mounting screws on the bottom. Alternatively, it can be fixed with a velcro strap. The front plate has 6 connectors, in which a keystone…
I designed a 3D printable version of our old cap badge. Printed with 6 different colour PLA filaments. Colour order silver white, red, darker red (ral 3003), black, blue, yellow prusa mini+ 0.4 nozzle 0.10 layer height select Avoid…
I updated the lids for this awesome storage solution a bit, the new lids stay in place on the containers and do not slide around. Many thanks to turbo_gecko for creating this beatiful insert! Category: Toy & Game Accessories
As seen on X and YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
I wanted to print this, but didn't have a printer big enough, or a way to cut acrylic. I cut through the internal walls to try to give the glue more to grab. My prints came out pretty rough, did them quick and dirty with a .80 nozzle, and…
I liked how some of the 7th Continent player boards held the State cards vertically but I didn't want a full player board. I decided I could just make a standalone card stand for 80mm cards. The slots are wide enough to fit cards with…
I loved the 7th Continent Discard tray by Aarcana, but I wanted to make it so that it could hold both the discard and the action deck. This was a quick clone and merge in Meshmixer. It has slots to hold the Discard insert on either side…
Card Tray+Lid for The 7th Continent boardgame I made back for the first edition when they sent replacement cards that people could use as a standalone version game by recreating the box and a few other accessories. The box is made to fit…
This is a card holder for the 7th Continent. I use 1 card holder for state cards (red hand) as well as bonus cards (green hand). Furthermore I use 1 card holder for experience point cards. This can also be found on thingiverse:…
March 7th from Honkai Star Rail. 3 versions. STL file with separated parts (with key to connect together)
I made this Wallmount for the iPad 7th gen. Should also fit 8th and 9th gen I made the fitment a bit tight so nobody could just pull it out. (still possible with force but be careful)
Intention to print these 4 parts and then use ½inch nominal (0.472 in) plywood for top and bottom. To use threaded rod (¼-20 or similar, those are 6.5mm holes) to clamp shut Still expect to have some revisions for detail geometry, maybe…
A tiny blocker for the Thrustmaster TH8A shifter. It's a bit longer than other models, to block the path to the 7th gear. In a normal movement to the right, you will hit the print and with a bit pressure you can go into reverse. Print…
I did my best to keep this description spoiler-free, but it might still spoil the plot, so be aware. If you haven't yet, I do suggest checking out the scenarios book with Dissociation. You may find it at DriveThruRPG . At some point in…
This is a collapsible version of a combined Action Deck and Discard Pile for the boardgame The 7th Continent . It's a very trivial print because you print all the sides flat and then slide them together. The only thing is to have the…
This is a card holder for the game The 7th Continent . It can be used to hold either the content of the Satchel or the players' hands (red cards, or even green/blue cards). It was inspired by Thing 3691427 , however I wanted the cards to…
This is a adventure card tray for the boardgame The 7th Continent . It measures 240 mm x 50 mm x 88 mm. The dividers in the picture are Thing 3700844 . Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution:…
Dividers for the game The 7th Continent . The first upload had the dividers with 1 mm thickness. After printing a couple, I think having them at 0.6 mm is sufficient. You can still scale them in Z axis if you want a different thickness. I…
Needed way to mount iPad to Sim Rig. Main use case is to use iPad as MCDU in Flight Sims. Found great wallmount from Bear_Grills and used it as base of this work. iPad slides in pretty well and is securely hold down because of the angle…
More divider cards for all the expansions of 7th continent and 7th Citadel. Possibility to print numbers with a different color changing filament ad layer #3 Added the base divider and numbers used if you need specific numbers to create
I made this insert box so that all miniatures could fit in the main box of The 7th Citadel boardgame. The only one that couldn't fit is the one in the small cardboard box written “Do not open”, that still fit beside the print, in the main…
![IRON MAN BUST_by max7th type2 [colouring 3mf remix]](https://media.printables.com/media/prints/d2dc7e58-03e3-4a65-b4c4-773ebaef8a87/images/11160928_13adb216-96db-4444-bea8-ff39c6e24c1d_68f0da33-d401-4a1b-9b02-270c69edd817/20251114_231404.jpg)
