Liczymy pasujące modele…
This computer case was designed for my Beelink SER5-Pro 5800H Mini PC but it may fit other Beelink computers and possibly other brands. Here are the steps to figure out if your PC will fit into this case: The hole is 131mm wide, 118 mm…
The Beelink Mini S12 perfectly fits in a server rack as a 1U device. I have designed a simple rack mount for 10" racks. Use the supplied screws that come with the Beelink mini PC (for the VESA adapter) to secure it to the baseplate, then…
This works for the Beelink SEi12 and SER5 Pro, as seen in the images. It's also pretty self-explanatory to tinker with the scale and make it wider or thinner to better facilitate the Mini PC you're dealing with. Original shape is inspired…
Made in PLA, 3 perimeters, 15% infill
I've created a remix which allows me to rack mount my Beelink EQ12 mini-pc.
This base is for BeeLink Mini PC with size 103x116mm, in my case it’s MINI S model My base is very lightweight and does not add extra bulk to the body, and it does not trap air as it does not have a grille. The standard rubber feet of the…
Vertical stand for Trigkey/ Beelink mini PCs. The PC slides in from the front. Feet are optional and should be made from TPU.
Remix of a remix. Fits the Beelink Mini S12 Pro. Have not tested with the non-pro model, but I imagine it works all the same. Friction fit so it is tight and doesn't move around once it's in place. Can use just the blank bracket mount to…
Beelink Mini PC 12th Gen Intel Alder Lake N100 tried to keep it accurate to 0.02% mm
Didn't come with the Mini PC so designed my own in F360. There are 2 versions v1 - VESA mount screws are NOT receesed v2 - VESA mount screws ARE receesed Forgot to take photo before it got mounted VESA screws are M4 - x4 and Mini PC mount…
1U! Print with petg due to heat requirements and likely deformation from thin walls. Will need to remove rubber feet in order to get it to fit in the 1U form factor. Can mount the PC into the tray using the screws included with the…
This Modkit is divided into two parts Upper part Lower part How to install 0. Remove the Lower part of the stock case and the Motherboard 1. Mount and Support the motherboard using the Upper part of Modkit Apply foam tape (2mm thick) in 2…
10" Rack mount for your Beelink SER5 Pro. Created using spuder's awesome tool here: https://makerworld.com/en/models/1765102-10-inch-mini-rack-generatorhttps://makerworld.com/en/models/1765102-10-inch-mini-rack-generator Had to slightly…
Modified and built for SER8.
Adding 10G and Sata functionality to the Beelink ME Mini
3D Holder for Beelink SER8 – Monitor Mount This is a custom-designed 3D holder made to securely mount your Beelink SER8 mini PC to the back of your monitor. It helps keep your workspace clean and organized by hiding the PC behind the…
These are three rackmount trays to hold my homelab components. 2x BeeLink S12 Minis 1x UCG-Ultra 1x FlexMini switch I modeled the front plate and trays together and split them in the slicer. The front plates will barely fit a standard i3…
A 10-inch Rack mount for Beelink EQ12 mini pc with PSU mounted on side.
This was made specifically for the Beelink U59 Mini PC https://www.amazon.com/dp/B09H5QXS6K?ref=ppx_yo2ov_dt_b_product_details&th=1
My original design was a 2 piece that bolted together. I didn't like the aesthetic of the screw heads sticking out of this bracket when all the rest of the machines in my rack have flat faces, so I redesigned the model as a single piece.…
A 1U bracket to mount a Beelink EQ14 in a 10-inch rack I designed and printed the Skeleten , a 10-inch rack to house my homelab. I wanted it to contain everything I needed, except maybe a NAS. From top to bottom: 2U - Vented TP-Link…
Enclosure for a Beelink Ser6 MiniPC along with an External Hard Drive for a super portable LAN party gaming computer. Includes BricsCAD (AutoCAD Compatible .dwg) model file. Designed in BricsCad. Vesa mountable to back of Monitor.
Rack for mounting Beelink Mini S13 on a 10" Lax Rax Server Rack For use with M6 OD8xL5 Heat Set Inserts as the original Lab Rax PETG highly recommended, as the Beelink Mini S13 could get hot and make the PLA sag a lot
Why another rack mount for the Beelink? TLDR: The others were just too flimsy for me. Modeling my own also gets me the features I want. The Beelink mini PC is ~40mm tall, which leaves only 4mm spare inside the thin 1U rack slot we all…
Wall mount for a Beelink SER5. The Beelink has long standoffs on the bottom, so the mount will only attach one way. I printed this with 70% infill, PLA+ and it clicks in place quite comfortably. Depending on what material you print with,…
VESA mount for BeeLink SFF PC. May work with others. PC mounting holes are slots not circles, making it able to fit differently spaced holes. Model files included. SFF PC mount = 3mm screws (recessed for buttonhead) VESA monitor mount =…
The model easy to print. Just cut it in a middle, print and glue it back together. For precise gluing use short peaces of filament. Printing parameters Nozzle: 0.4 Layer: 0.2 Perimeters: 4 Infill: 40% Top/Bottom solid layers: 10 Material:…
As requested by a Reddit user. Work in progress!
This lets the side vents work better to suck air from the bottom and vent out the top and back. Prints without supports.
This is a fitted 10" rackmount for the Bee-Link EQ14. It has cutouts for ventilation, and a bottomless design to accomodate the router without going over 1U in height. Required hardware: Screws and cage nuts that came with your cabinet,…
Print with the front face down, 100% infill or 4 thick wall thickness. This mount is intended to decrease glutter while allowing for optimal cooling
I got one of these Beelink mini pcs to use for a plex server. It comes with an empty internal bay for a 2.5 inch hard drive, but there is extremely little clearance around it. The hard drive I wanted to add was apparently more rubenesque…
Did a quick cover for my Beelink ME mini. to gewt the airflow and space for heatsink for nvme. Work in progress, But it works and the thermals are good. It can be installed without the bottom screws. I made a latch (ident) This is REV 2.0…
There are two M3 threaded holes in the nettop case. Distance between holes 32 mm.
A simple bracket model to allow for under table mounting of the Beelink SER8 Mini PC
A quick holder for the Beelink T4 PRO to mount to surfaces. Air holes for improved ventillation and recessed wings for double sided tape. In use currently as a holder for the T4 Pro on digital displays. It hides the device nicely on the…
Tight fit for the Ser5 Pro, so the walls aren't as thick, due to the height of the device. I had to remove the rubber feet on the bottom of the device. I used supports on my print, though you may not have to depending on your printer's…
Very simple model. Uses the same screws as the original bottom, and additional m3 screws.
A 10 inch rack mount for a Beelink mini pc and a jet KVM. I've oriented the 3MF and supported it where necessary to allow for IO.
Made because I was worried about the temps on this machine running for a long time. Comes with mounting through holes for a 120mm fan. After multiple revisions after failure with magnets to join the two halves, I decided to just use…
Designed for Beelink SER7 You need 3pcs of M3 self tapping scew
Suitable for the Beelink EQ13 mini PC, there are two cutouts on the underside for the fan and the ports (USB, LAN, Power, HDMI). Printed with PLA, 3 perimeters, use 3.5mm countersunk screws. The Beelink EQ13 is a perfect and powerful mini…
I designed a stand for the Beelink GTi12, GTi13, and GTi14 mini PCs. Since the ventilation holes are on the bottom, this design ensures that the PC gets enough airflow. Of course, it should also look stylish, not just be practical. I used…
This is a remix to add a Beelink MiniS 12 Pro to Robert's excellent 19" 1U Modular mount system . Since the Beelink is too wide to fit in a single module, I remixed the entire right and left side pieces. This is a precise fit, and the…
💻 Skadis Mount for Beelink Mini PC SER5 A compact, 3D-printable holder designed to mount the Beelink Mini PC SER5 directly onto the IKEA Skadis pegboard. Attachment: Uses three integrated hooks for a secure, sideways mounting position.
120mm fan adapter to connect to beelink GTR7 mini PC. I get -5C max temp and quieter operation. Print main plate facing down and support from plate to legs. Print Settings Rafts: No Supports: Yes Resolution: 0.25 Infill: 15% Filament: any…
Case for the Beelink SER9 Pro HX 370 with mounting holes for attaching to a HSW using the M3 nut inserts. Use M3x10mm BHCS. Has a variety of mounting points but I've only used the ones in the corners and the PC is rock solid. The holes…
Wall or Underdesk mount for Beelink EQI12 series mini pcs.
Beelink Me mini PC/server wallmount I designed it to have airflow and access to all ports I used #8 by 1" wood screws Printed in PETG with standard settings
Loved the AppleTV Mount and needed a similar option for a Beelink SER5 Pro. Widened the gap on the rear hanger arm to allow for it to slot onto the back of a TV wall mount. Fit is a little loose, bit it will hold the SER5 Pro just fine.
Hey folks, I recently purchased a Beelink SER8 and needed something to attach it to my VESA compatible display stand. Since there was nothing around to buy or directly print, I reckoned I'd design one and print it. I chose VESA 75 since…
I was working on some cable management for my desk, which included mounting a Skadis to the back of my monitor. I didn't have a good way to secure a mini PC I use for 3D scanning to the back of the Skadis, so I came up with this. It…
Remix of the BeeLink Mini Vesa Mount but with 80mm spacing for the ikea skadis board.
Riser with optional caddy slot for a 2.5" drive (in a 79mm x 126mm case). Designed to neatly set the Beelink EQ14 on top allowing more airflow below. Tray with optional hex or mesh patterns can be printed and pushed in / glued into the…
Stand for a mini pc or anything else about that size to increase airflow.
Fits ESRack mounts and other accessories used Elegoo PLA
A 100mm VESA mount for Beelink Mini PC SER6-P. https://www.beelink.at/computer/mini-pc-beelink-ser6-p--16-32gb-ram--1-2tb/ I designed it so that the backplate has to be removed to use the screw holes in the device. The case is designed to…
Discover an efficient and innovative solution for organizing your workspace with this meticulously designed 3D model stand for Beelink SER6 Max. This model, crafted by a reputable designer known as Perpetual Printer, uniquely integrates…
This is a 10 inch, 2.5U rack mount for the Beelink ME mini NAS. Features both top and bottom mounting options depending on where you would like to add an additional 0.5U item above or below the NAS. Print the handles (with tree supports…
Beelink SEI8 support, or any kind of device that is 125mm wide and 42mm height. You should print two unit of that. Printed using PLA
This is a Beelink SER9 case ment for a 10 inch rack like the rackmate t1. Printed in PETG to avoid issues with heat.This is a Beelink SER9 case ment for a 10 inch rack like the rackmate t1. Printed in PETG to avoid issues with heat. The…
I am in the process of building a new control cabinet and stand for my CNC plasma table, I am using a Viewsonic ViewSonic TD2211 Resistive Touch Screen Monitor, with a Beelink EQi12 for the CNCPC. I wanted a way to mount the the little PC…
Secures the SER9 to the back of the monitor/television while allowing full-access to all plugs and, depending on the contour of the monitor back surface, may create additional air flow into the bottom of the computer. Spacers can also be…
Beelink S1 Mini mount for the wall. Uses m3 Flat heads to connect the top and bottom shell, with holes to secure the mount to the wall with wood screws. Assembly is a bit tricky, so print at your own risk.
This Modkit converts Beelink ME mini NAS to use an External DC power adapter. You can Remove the Internal Built-in PSU that generates heat inside the device and Replace it with an External DC adapter. Items Needed Multimeter (to check DC…
I couldn't find any mounts that would allow the usb ports to remain free on the t34. This allows you to mount the mini PC to the wall with 4 screws, and to the mounting holes with two m3 SHCS or BHCS.
Ikea Skadis mount for Beelink EQ14
I printed it with 0.2, 40% infill, brim and supports and worked well with PLA. Have not tried other settings. This is an original model, inspired by brackets for similar other Beelink models with different dimensions.
This is a bracket I created for mounting my Beelink Mini PC to a 4" diameter pier at Starfront Observatory. I have added holes for zip ties to pass through the body of the bracket for securing to the pier. There are also some rectangular…
I make this top cover for my Beelink ser6 pro for easy access to the fan from the top. is 122mm x 110mm x 2.5mm. you will need to drill the holes for the m2 bolt.
A custom baseplate for the not-so-well-loved member of the Beelink family, for additional venting. I uploaded the 3MF file where the parameters should already be set to print the mesh properly. Model is split into 2 parts. The mesh part…
This mounting bracket provides a convenient way to mount the Beelink MINIS 12 PRO mini PC—or similar 104L x 116W x 40H systems—to an equatorial mount, wall, desk, equipment rack, or other suitable surface. The bracket features a mounting…
This is a frame to hold a Beelink Mini S computer. I wanted to guard the power button from accidental presses, and hold the box steady for easy insertion and removal of a USB stick. I also wanted to be able to remove the entire computer…
I added to the wonderful ESRack collection originated by @EvilProphet. I designed this module using Fusion. It fits a BeeLink EQR6 + 1 JetKVM + 2 Keystone jacks in a single 2U ESRack bracket. According to BeeLink website, EQR7, EQRi12 and…
My S13 was throttling hard under load. So I designed a custom case with a 120mm case. Full project on hackaday Unleash the N150 CPU aka "Pimp my Mini PC" | Hackaday.io The pcb and code will released as open hardware/software Current state…
Designed this to use as a stand for my Beelink SER6 MAX Mini Desktop PC. I also included two stops that snap onto the rear end stops just incase you needed them. also printed with no supports but used optimal setting on ender 3 v2. Print…
It is designed for M4 x 30mm machine screws (hopefully similar to the stock fan screws). The fan is rotated relative to the base to leave access to the holes for screwing in the base. Insert the fan into the wider slot cutout on the top…
Wall mount compatible with Beelink ME mini. I couldn't find any wall mounts to hold my Beelink ME mini, so I made one. Keep in mind, the Beelink will need to be rotated sideways to reach the I/O ports. Currently this is hanging in my…
Overview (English) This two-part holder mounts a Beelink EQR6 mini PC vertically on an original IKEA SKÅDIS pegboard while preserving its intended airflow as far as possible. Installed orientation: - textured top cover toward the SKÅDIS…
This BeeLink EQ14 mount is designed to be used with Multiboard, using four Mulitboard Flush Snap Small Thread Holes.
A VESA bracket that gets your Beelink SER8 Mini-PC off the desk and onto a monitor arm. The mini PC sits in an open cradle rather than being clamped or strapped, so it drops in from the top and lifts straight back out — no disassembly…
Wall mount for BellLink EQ12 mini pc. No supports. Holes sized for #8 drywall screws.
If you like what i'm making, Please consider buying me a beer 😀 📦 Ready-to-use versions of my designs, made to order and shipped to you. 🔩 All hardware included for a quick install. 👉 Mixmeister3d A 19-Inch Rackmount for 3X Beelink S12…
Description Mount your Beelink MiniS (or similarly sized) mini PC to a dovetail with this 3D-printed adapter. It is designed for Aperturea D or V series clamps and is likely compatible with any clamp that uses 35mm screw-hole spacing and…
Please note that this stand does not have ventilation channels. It is designed to be placed on a mesh or other open surface that allows air to flow from below. See the attached photos for an example. I will soon make another version with…
Wall mount for a Beelink SER5. The Beelink has long standoffs on the bottom, so the mount will only attach one way. I printed this with 70% infill, PLA+ and it clicks in place quite comfortably. Depending on what material you print with,…
Did a quick cover for my Beelink ME mini. to gewt the airflow and space for heatsink for nvme. Work in progress, But it works and the thermals are good. It can be installed without the bottom screws. I made a latch (ident) This is REV 2.0…
This is a Beelink SER9 case ment for a 10 inch rack like the rackmate t1. Printed in PETG to avoid issues with heat.This is a Beelink SER9 case ment for a 10 inch rack like the rackmate t1. Printed in PETG to avoid issues with heat. The…
A 10-inch Rack mount for Beelink EQ12 mini pc with PSU mounted on side.
This is a bracket I created for mounting my Beelink Mini PC to a 4" diameter pier at Starfront Observatory. I have added holes for zip ties to pass through the body of the bracket for securing to the pier. There are also some rectangular…
This BeeLink EQ14 mount is designed to be used with Multiboard, using four Mulitboard Flush Snap Small Thread Holes.
This is a frame to hold a Beelink Mini S computer. I wanted to guard the power button from accidental presses, and hold the box steady for easy insertion and removal of a USB stick. I also wanted to be able to remove the entire computer…
I added to the wonderful ESRack collection originated by @EvilProphet. I designed this module using Fusion. It fits a BeeLink EQR6 + 1 JetKVM + 2 Keystone jacks in a single 2U ESRack bracket. According to BeeLink website, EQR7, EQRi12 and…
This is a fitted 10" rackmount for the Bee-Link EQ14. It has cutouts for ventilation, and a bottomless design to accomodate the router without going over 1U in height. Required hardware: Screws and cage nuts that came with your cabinet,…
