Liczymy pasujące modele…
I needed a dropper compatible under saddle mount for my cateye rapid mini. I really liked my solution for Ergon Saddles , and copied the design over to the saddle rail interface from this solution . IMPORTANT NOTE : PETG will creep, I…
A rear bike light mount specifically for the Cateye rear lights (specific models below) to mount under an Ergon QuickClick supported saddle. Ultralight and sturdy! Saddles Ergon saddles with Topeak's QuickClick mount. Locate a threaded…
This is a mount for Cateye rear light that attaches to saddle rails by zip ties. It's semi universal, it won't fit every saddle, but it should fit most of them. There are 4 versions for different saddle rail sweeps: 9°, 20°, 30° and 41°.…
Cateye Ampp adaptator for GoPro mount
Users say that it works with other Volt models (e.g. Volt800) Update to version 2: I changed place where the mount is located (now it's in the back), so it helps to stabilize the lamp when mounted BELOW Garmin bike computer mount. Volt400…
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999). Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. As bonus I added reinforcing ring for my…
I really liked my solution for Ergon Saddles , and copied the design over to the saddle rail interface from this solution BUT a design that wouldn't interfere with my saddle position being pushed totally forward like this one would . So,…
I lost the original nut and could not mount the LED anymore, this is the replacement of the original nut Print instructions I printed mine using Prusament PETG, no supports required
A bike light mount designed for the Cateye TL-LD130 / TL-LD150 and similar Cateye lights. A 6-32 screw and nut works well to secure it. It's a friction fit with the bike light, if your tolerances don't provide a tight fit, then scale the…
I have tested it with the Strada, but it should work with other Cateye models that use the same adapter. Print Settings I did not print this myself, but outsourced it to my local university shop, so I do not know all of the settings other…
Cateye AMPP400 Mounting Bracket My original Cateye Bracket for AMPP400 light spacer broke, and no replacement was to buy in my country. So did a model of it. Matches AMPP400 (Maybe others as well?) Original sparepart: 5340920 Printing…
I printed this model out of PLA with a 0.2 mm nozzle. A 0.4 mm might have done the job too. The part fits great, it is very similar to the original. It might also fit other cateye products.
I just didn't wanna buy this one, which is oem CATEYE OF-100 Out Front Bike Computer Bracket so I made this! REQUIRED HARDWARE: 2x m3 nut 2x m3x8mm, or really, anything longer than 7mm ….thats it PRINTING RECOMMENDATIONS: Filament: PETG,…
Blendr compatible GoPro mount for CatEye AMPP lights. Use of Supports is recommended. It might be due to my tolerances, but the mount itself is quite tight and the mount on the light did not reach the end initially but moving is back and…
Works with every saddle with 7mm axes. Very simple, no screw. Cateye light only (Viz and Rapid mini)
Custom CatEye light mount I made for a friend to replace his broken original mount. This was used for a Volt800
Update 2025-01-24 : Fixed an unattatched sketch in the FCStd file. The clips on my Cateye Reflex Auto broke and I could not easily find a replacement. This is why I decided to model and print a replacement shell. That was a mistake. This…
My little one fell and the original broke. this is 100% Copatible. I Printed in black PETG for the flex. Sideways because of the bending of the part.
This started out a a request by a friend who bought the wrong bar fly mount for his Cateye Micro wireless cyclo computer. He didn't want to return the thing so I made an adapter based on the stock tube mount and the bar fly. NOTE: When…
Replacement clip for the cateye ORB bike light. Basic but does the job. Print hot and slow for better print strength
Mostly same as original, I used 0.1mm layer height. Filament: PETG Infill: >30% Perimeters: 4 Bottom Layers: >5mm Layer height: 0.2mm (0.1mm for smoother finish) Orientation: flexing tab should be flat to bed (see gcode example) Supports:…
The original Brompton saddle light bracket is neat, but makes the light not very useful because this can be easily covered by the hem of your jacket or your clothing in general. So I thought of an extended version of it, to drop the light…
Update 12 Oct 2019: The original design worked pretty well, but wasn't perfect. I redesigned it from scratch in Fusion 360. There are now three pieces: Cateye cage top bolt locator Cateye cage top bolt spacer Cateye cage bottom bolt…
Intended to be used Magnetic Mani Nail Polish Velvet Effect Magnet Holder (separate files for both short, long ), it suspends a bar magnet over the top of the Velvet Effect Holder, creating the Velvetized Cateye effect. Requires one…
Cateye makes great mounts for their lights, but centrally mounted ligh looks so much better. It's also more aero, but if you are into that you have probably figured out that no light is even more arero, duh! Hardware required:…
A Cateye light mount for a 22.2mm handlebar diameter. The design comes in two variations depending on what screws you have laying around: #4x1/2-inch wood screw PC case fan screw (5mm major diameter, 10 mm length) Print conditions: PETG…
Printed in PLA or ABS, mount on you Bike using M4 Screws Paste Reflector tape as you wish ;)
I printed in ASA right side up and was fine.
Simple mount for the CatEye ViZ series of lights (tested with my ViZ450). Should be compatible with other CatEye lights (Reflex Auto, Tight Kinetic, Nano). Mounts to my Axiom Streamliner DLX rear rack, which has vertical holes 19mm apart.…
Supports required. Printed in PLA/PETG/PC. Tested on a bike. Printed in 45 degree angle provides more strength for locking pins. V3 has a better detachment of Cateye Omni lamp.
Cateye Rapid X3 holder for ebikes
A sleek, bolt-on solution to mount your CatEye rear light directly to Specialized or Syncros saddles using their integrated threaded holes. Say goodbye to rubber straps and enjoy a cleaner, more secure, and aerodynamic setup.
Adatpor for Wuben X4 light for the CatEye H34 mounts ( handlebars , gopro , fork ), suitable with the Brompton mount for Cateye. I used screws form the original Wuben bike mount . Also requires a spring, original one is 3x7x0,5mm. I…
Bicycle Signal Holder CatEye LD610 Taillight front: cone frame ø50 ø60 150mm 16° rear: seatpost 30.8mm -16° https://www.aliexpress.com/item/4001119231828.html Category: Sport & Outdoors
I wanted a better way to mount my Outdoor Tech Buckshot 2.0 speaker, so I made this. This thing was made with Tinkercad ( remix it ).
The mounting kit is no longer made, but the computer still works fine. Why throw it out? You need some thin tinned wire to make the contacts. Solder quickly with good no-wash flux so the plastic doesn't have time to melt. It's fine - just…
Printed with 0.2mm layer height. Rotate so that it lays flat on the bed, support required for hole. Remove strap from bike light and attach to mount. Use a cable tie (zip tie) to attach it to the handlebars. Update 25/01/25: Made the…
The original Cateye clamp has the quick release for the light already. So I created an adapter to use that by creating a very short cylinder for the clamp to fit on and then a slightly offset tab that accepts a bolt and not to attach to…
Custom CatEye light mount repair I made to replace broken original mount. This is being used for a Volt400 over last 2 years daily.
I designed and made this for my son who recently got his bike stolen, and unfortunately many of the designs I came across made the presence of an Airtag or similar device fairly obvious. This method is far more discreet in my opinion and…
I needed to mount my (very old) Cateye HL-EL 130/138 not to the handlebars, but to the handlebars stem. Since the stem is at an angle, this needed to be angled as well. So there are 4 distinct parameters of the model: CLIP_TO_BAR_ANGLE :…
Update 12 Oct 2019: The original design worked pretty well, but wasn't perfect. I redesigned it from scratch in Fusion 360. There are now three pieces: Cateye cage top bolt locator Cateye cage top bolt spacer Cateye cage bottom bolt…
Have this rear light of which the rubber broke a while ago BUT its a good light. This is a replacement for that so I can use this light again. The seat post mount is for 31.8mm seatposts (which should be standard for most bikes). Parts…
This is a holder for the CATEYE WEARABLE safety light. I designed it so that it can be attached to the helmet with a cable tie, but I also provided a standalone holder so you can edit it so that you can attach it wherever you like.
Simple remix adding baseplate that can be drilled to fit mounting holes on bike racks
A bike light mount designed for the Cateye TL-LD130 / TL-LD150 and similar Cateye lights. A 6-32 screw and nut works well to secure it. It's a friction fit with the bike light, if your tolerances don't provide a tight fit, then scale the…
Chevrolet Silverado GMT800 Cateye Wall Art; can be scaled easily and can be hung or stand alone. I also take requests
Rubber protective replacement part for back charging usb port. Printed with Overture TPU and standard Bambu TPU settings. Matches very good. Does not fall off. Sticks very well
Description This is a holder for installing the Cat Eye RAPID mini tail light TL-LD635-R horizontally on a Specialized power saddle. It is common to attach it vertically to the seat post, but by attaching it to the saddle, you can raise…
A Strada Slim computer will lock in place and allow the user to change the computers mode by pressing the bottom of the computer just like the factory clips. This model is intended to be fastened to the handle bars using two ~1.5x2.5mm…
