Liczymy pasujące modele…
*NOTICE* If your duct is not centered to the nozzle, please print the offset version of the duct that offsets the ducts 2mm to the right to try and correct for this. There does not seem to be a reliable pattern for what machines need the…
Opening a door as a firefighter, law enforcement officer or emergency doctor can be a challenge sometimes- but KEEPING it open can be just as important. If you are tired of jamming doormats and trashcans into doorways then this print is…
Want a quick, firm, durable connection for your PTFE lines? For quick diagnostic, quick swapping , without afflicting much damage on the PTFE itself? Want a universal connection that can act as an extender, terminal at the same time? Want…
A design by EGoe from Thingiverse for a J1772 Tesla Adaptor Lock, with some considerate modifications: Bi-directional There is a small press-fit that helps keep the ring attached to the adaptor while you carry it around. There are two…
parts required 2x 3/16" washer (Ø14mm and 1.2mm height) 1x M3 14mm socket head screw (leftover from the Prusa MK3S kit). Slightly longer or shorter is okay. 1x spring from unused pen optional 1x M3 washer I was inspire by FreddyZ and…
This model is a bidirectional cable chain based upon the igus Triflex series energy chain. These are used to wire up rotational systems where the cable cannot be routed through the center of the axis of rotation. An example use case would…
Blog: https://dev.joesturge.com/p/3d-print-in-place-a-design-journey/ OnShape Files: https://cad.onshape.com/documents/5b146e263caac3060752204d/w/15bde26dc6901519c376ed2c/e/cecbda455fb1c20a8470df09 Features Fully print-in-place – no…
This is a omni directional wind turbine designed to be installed outdoors on the rails of your deck or just stick it in a potted plant. This design will catch wind from all directions and the turbine does not have to face the wind. I have…
My wife wanted a pumpkin clicky fidget for her elementary school class. I have a box of knockoff blue cherry mx key switches, and found the model that she saw online. Unfortunately, the included key cap wouldn't work with these off-brand…
To vent exhaust air in a specific direction if you have your desktop up on a table like me. Reduced noise by ~3db (roughly, measured on smartphone at where my head usually is) idle and ~6db under load. Also heat isn't dumped near my face…
This is a modified XRP chassis with swerve drive modules. I tried to keep most of the original XRP features, so the size and mounting rails are the same. Both the battery and the controller are mounted in a frame as in the original…
Remix from: https://www.printables.com/model/767068-spinning-filament-swatch-display-lifts-swatches/remixes Wanted to have the model spin both ways so I just mirrored the ramp. Let me know how it prints for you! Mine worked great.
I have used various cable chains on my printer, but over time I wanted something simpler. So I designed this octagonal cable chain to solve all my problems! Each chain link is one piece (no covers to snap on!) No supports are required to…
Model designed in Autodesk Fusion. Antenna created with Moxgen software. Dan Maguire AC6LA https://www.ac6la.com/moxgen1.html Design under Autodesk Fusion360. Mount for navigation holder. Mount for Ikea Tisken suction cup.
This is a directional air duct vent for a 120mm PC case fan to guide the airflow. I would recommended to use support material as some parts of the internal slope are quite steep. It should be quite easy to remove this support material…
These are single-piece directional Multiconnect snaps for openGrid that allows for increased weight compared to the non-directional version. This is a remix of origin415 's openGrid full/lite Multiconnect Multiboard Adapter but…
This is another one of those telescoping widgets, scaled into a smallish twisted cube. It prints in place without supports. I've included 2 models: one that prints ready-to-fidget, and another with small tabs across the bottom of the part…
The Foam Comb (Fomb) is a simple printable tool for picking up nearly any dart type no matter their orientation! No need to aim, simply stab the ground with the Fomb to pick up darts and use the bucket fork to offload! The only…
I done this file, so long ago, I used the base of the original file with a lot of modifications in tinker cad, which was not easy for me LOL I needed to direct the heat away from my unit printed this upside down
Self made directional WLAN Antenna EXTENSION in YAGI style for 2.4 Ghz WLAN with regular copper rods. To optimize you WIFI environment. Instructions Use 0.75 mm² (1 mm diameter) Copper Rods for 2.4-GHz-Antenna-Extension: Position -…
This is a fully 3d printed mecanum drive for your XRP perfect for indoor and small spaces. For outdoor exploration I would recommend you some of my other mods like the xrp off-road mod , the xrp track system or if you wanna go to water…
This is a bidirectional bolt, inspired from https://youtu.be/cDfMI5ahbJI ,.
Huge props to the original creator @triton_9, I just remixed. This remix contains a few tweaks to the design; specifically: I created a female adapter so you can go the other direction The wooden track adapter/prong was too long for my…
Remix to divert exhaust straight back. I was looking for similar files and liked the minimalist design, however I did want the exhaust to go back as I do use the short attachments. I was finding the regular exhaust was blowing debris…
This is a 12-sided omnidirectional speaker design inspired by https://www.thingiverse.com/thing:24308 (but designed from scratch). It fits 120 mm speakers (YD120-1). I will try and provide a more detailed description of the build, but…
Noctua posted a teaser video and images of this design on Twitter. I looked at the images and designed this. It works alright with NF-P12 I printed with custom paint-on-support
I stumbled upon a pair of these vintage loudspeakers on Craigslist and while I couldn't justify buying a full-sized pair, I thought they were so unique that I wanted to recreate them in 3D printable form. Each speaker consists of a top…
This robot is meant to be an improvement to the existing XRP robot drive base. The robot utilizes three omni-wheels to allow the robot to move in any direction at a time. By enabling holonomic motion with this drive base provides students…
The T shaped directional golf ball stencil insert provides a fun marker friendly logo that stands out on any golf ball that works with the PrintSphere Golf Ball Stencil Holder ( hinged or unhinged ) or the Golf Ball Spray Paint Stencil…
I looked at the duplo compatible bracket and thought, hey, why not do this is every direction! My eldest child really loves this one. They used it to make a robot head : )
This is an Dremel press extension for the Highly Adjustable Ball Vise System https://www.printables.com/model/1109371-highly-adjustable-ball-vise-system You can engraving sanding drilling ceramics, wood, 3d printed parts form all…
There are no tolerances built into these models, so you can add your own xy-tolerances in your slicer of choice. (in S3D the setting is called Horizontal size compensation)
This is a remix of Syntaxcuemi3D's Twin Wheeled Filament Guide. This Is a multi directional filament guide for Spools mounted above printer. Not only does the head turn, but it slides in the top channel for least amount of resistance on…
I needed a quick way to splice 4mm OD PTFE from my Bambulab AMS to my P1P, and needed it to have no resistance as it was being fed through. The center guide is slightly larger than the 2mm ID as the filament exits the AMS side, and…
Here's a couple of omnidirectional scrapers you can use for removing prints. I've resized them to something a bit more appropriate (i.e. 50% of their original size). Note: I didn't update the renders of them, so they just look large in…
Blackmagicdesign Mirco Converter BiDirectional SDI/Hdmi Holder The converter slides in and does not slide out. I sliced with Cura and used tree supports for overhangs. Cheers Print Settings Printer Brand: Creality Printer: Ender 3 Rafts:…
The wheel adaptor will fit over the main button relay but you will need to change the Hex bolts to M4 16mm instead of its default ones. To attach the wheel - wood screws 8gauge 14mm x6 screws My settings .2 layer height 3 walls 60% infill…
This is a remix of the Chimes_Industries wheel, built for installation on 12mm RC models, easy to install and removable
Easily attach your rockit to any stroller or bedframe. Single print can be attached in any feasible direction with just two zipties. Prints without supports easily if printed on the small, bottom base. None of the other existing models of…
Cam lock that visually shows you when it is in the open direction. I had found my v0.2 r1 cam lock would often move out of alignment when the lid was open. With a hex this was hard to tell. The arrow points to the opening to resolve this.…
Mounting a Blackmagic Design BiDirectional SDI Converter to a DAP 2HE 19" Rackmount . Combine with other available Parts for RasperryPi and others. Replace the existing M3 screws on the bottom with two M3x8 or better M3x9
This is exactly the same as the remixed library however it allows the grid to work for vertical shapes as well as horizontal. Just call cuboid_grid([x,y,z], hex_width, wall_width); And the grid will render on the side with the largest…
Hardware: M3*20 Hex socket machine screw: 4 M3 nut: 4 4mm diameter, 2mm height magnet: 4 Assembly: Prepare all parts. PLA is fine for all parts, but i suggest PETG for the "slider latch" which has flexing pins. Print with 4+ walls and 30%…
a fan cover for 120mm fans, with directional slots
Designed to fit in Artic P14 or any 14 cm PC fans to directional air flow.
There are many Makita LXT 18-volt battery holders…. this one is different! All the other holders you will see out there are unidirectional. You can only slide the battery on from one side. This one allows you to slide the battery on from…
Fully mechanical binary counter that can count up and down. It's modular so you can extend to whatever digit you want. Update 04.07.2024 I modified the bases, connectors, handles and added a lock to the left side to enhance the design…
This allows you to spin nuts in different directions on the same bolt. It’s a very fun fidget toy.
A servo horn that allows endless rotations by moving back and forth (only one direction) - fine ratchet as only two mesh
Dual 5015 Fan assembly for cooling drone VTX on the bench when FPV drone is connected to battery, to avoid overheating. Powered through switch, and used DC to DC buck converter to keep voltage at 12v regardless of the battery type plugged…
Useful for washing down the inside of pipes, for example boat trailers. Important: This requires supports around the opening where the water comes out. Gardena version:…
This is a directional nozzle for air humidifiers. Thanks to it, steam comes out in desired direction. Works with these humidifiers: Malatec 16404 Powermat PM-NPO-4W Caruzzo ULTRASONIC-JS1802 Recommended print settings layer height: 0.1 mm…
Used to hang items from string/rope and be able to point them in any direction you want. *Some supports required.
The OEM 8-way restrictor only has positive engagement in the UpLeft, UpRight, DownLeft, and DownRight directions which leaves Up, Down, Left, and Right with a sloppy feel. This gives the joystick positive engagement in all 8 directions.
A nozzle to allow 360 degree coverage of the cutting cool from only one Loc-Line. Solved the problem I had where with only one nozzle, sometimes the cutter of my CNC router or the part geometry would stop the coolant from reaching the…
My implementation of a multidirectional stand for the Nintendo Switch, utilizing the joycon rails on the console itself. This design emphasizes simplicity and minimalism. It works in normal (horizontal), vertical and reverse vertical…
Print the main bracket strong. Other than that, have fun and choose a nice color!
2/3/2020: Anchor Firing Gun: Modeled in Fusion 360 after I found some really good refs, I've attached them below. According to the guide books the connector bit is supposed to turn so I put it in there separately in case anyone is really…
I own a repair shop in the middle of a small rural area. People, God love them, have trouble figuring out that they need to push the door open, so they wind up standing outside and just knocking. To remedy this, I created these signs. One…
12 Sided Die Multi-Directional Display (Solid or Vase Mode) Put open side down with tealight for all around glow effect, tilt on side for display, or open side up for a decorative vase. Looks great in white. Printing Instructions Vase…
OFRT-8a - Omnidirectional Full-Range Tornado, model 8a, loudspeaker. This loudspeaker features a single full-range driver facing upward, accompanied by two conical-shaped sound reflectors. The driver placement facing upward, ensures that…
Support me: Post a Make and Comment PayPal Venmo: @paulorfo Cash App: $paulorfo ------------------------------------------- Disclaimer: Posted as original design because the designer Keep Making didn't post it here. He made a dedicated…
3D PRINTED DIRECTIONAL DEVICE TO GUIDE FILAMENT WINDING ON A SPOOL. FILAMENT DIRECTOR FOR WINDING PROCESS. Project for 5 cm wide coil. For +/- cm, need adjust.
How often have you found that Lego Technic pieces don't have a pin-hole in the place you want, or in the right orientation? Then this piece is for you! Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: Yes Resolution:…
I designed a clip for the Boya BY-M1 Omnidirectional Lavalier Microphone as mine broke and needed and urgent replacement. I tested the model and it works perfectly. Best printed with: 1.6 mm layer high for strength
The only change in this remix was to make a bidirectional version of the cradle. Works no matter which side of the gantry you attach it. Major kudos to Ryan of V1 Engineering for releasing the LowRider v4 CNC ! This FluidDial CRADLE v2.3…
Print a custom nozzle organizing box suited for your exact needs. Designed for each nozzle size to be printed in a different colour with one labelled version per size. Inspired by my old linear connecting design, this time with improved…
BOM and Size Speaker : 3", Bolt Circle Diameter : 85mm BT Amp : 47mm x 47mm x 18mm ( 47mm x 67mm x 18mm ) USB-C PD to DC : 2.3mm x 1.2mm or DC 5.5 connector M3 Insert and bolt
Designed case for "NFJ's SmartSpeaker Assembly". Parts(per 1 unit): Speaker Assembly NFJ's SmartSpeaker http://nfj2019.livedoor.blog/archives/4354571.html https://store.shopping.yahoo.co.jp/nfj/s0393.html base plate 120mm FAN blank panel…
Rational I wanted to test 60 degree overhangs in all directions to calibrate the fan speed and print speed for PETG. I wanted a model that would print quick to avoid wasting hours testing multiple settings. So I created this simple “star”…
It's a marker for scuba diving
Needed a simple air scrubber for inside an enclosure, wasn't requiring an extractive style venting system due to the materials being printed but wanted something that would filter the air trapped inside. An air scrubber fit the bill and…
Small side hook to attach the converter with a zip tie or a 1/4" screw to your camera. You will need two M3x8 screws to attach it. I printed them in PETG.
This is 868Mhz LoRa Meshtastic Yagi-Uda directional antenna with 6 elements and square boom. Actually calculated for 869Mhz, since this is closer to real meshtastic working frequency in UE). Dimensions were taken from widely-known DL6WU…
This 2-way restrictor plate fits Sanwa JLW Joysticks. The restrictor plate mounts either vertical or horizontal for optimal fitment. Print yourself a replacement 2-way restrictor.
All-in-one door wedge for Paramedic
A mounting solution for a tablet or other screen for the common 10mm microphone swingarm mount. Designed for the 7" Waveshare Universal Display Monitor. The screen clip has a dovetailed connection on the rear, which allows the screen to…
Botón cinco-direcciones del mando del Fimi X8 SE (Si, el botón que se suele perder...) Imprimir con altura de capa de 0.1mm, muy despacio y con ventilador de capa. Otra posibilidad es imprimir varios al mismo tiempo para un mejor…
Notes: The vent body does not rotate inside the AC vent opening as it uses the size of the print to push itself into the AC Vent hole. Print Setting Instructions/Tips: Use PETG or ABS or ASA or stronger material with better heat…
this is an incredible design by @Jude3d, and then it was remixed by @ArduinoPrints3D and I was very impressed with it, but felt it would be more fun if it were longer, so here I have lengthened it so where the original screw was 111mm…
Print with 4 walls and 15% infill. You will need 2 M3x20 socket head screws and 2 M3 Nuts
The models are Fusion360 files
Premise The idea behind this whole endeavor was to use the new FS2026 system without having to waste filament on printing an entirely new lid or having to drill a hole into the box, and consequently being able to use the box in its…
IMPORTANT: There are many different Blackmagic micro converters all named very similarly. Please confirm that your unit's name matches verbatim to the model name! ~Blackmagicdesign Micro Converter BiDirectional SDI/HDMI 3G I made this…
See these lovely hooks in action here: https://youtu.be/qIaC3iQplTU
Like the one below, but with gardena connection https://www.printables.com/model/220631-omnidirectional-spraying-nozzle-for-garden-hose
Sanwa JLW restrictor plates can break when the screws are inserted too tight. Print yourself a replacement 4-way restrictor.
UBBI added to little arms so you can screw-mount them to your aluminum extrusions. Credit to Tyguy94920 for the first attempt/conversation on Discord. “Up” and “Down” refers to which side the UBBI quick disconnect is on.
I have built a dust collection system for my workbench. I needed some custom adaptors for the different piping i use and Blast gates. The idea is that it always cup the intake and goes inside the outtake everything is parametric so if you…
A simple remix of the work by BuildX to create a quick and simple over hang test allowing multiple angles to be tested. This modification allows testing to be isolated to one direction to test overhang ability and account/test for…
A directional louver for a Coleman-Mach RV air conditioner found on the Winnebago Rialta RV. This part directs the cold air inside the cabin. Twelve fins are required for the ceiling distribution assembly mounted inside the coach under…
A simple cover for a BR30 directional light shade that covers a portion of the light directionally. Recommended for LEDs I imagine it's a fire risk if it's a hotter bulb Print instructions Printing Bottom Up seems to work fine, the…
Print in place with a 3 wall thickness and 5% infill, I also used a brim and 50 degree overhang supports to stop ball (wheel from moving) . I would also suggest at least 10% support as %5 was a bit messy. Have also updated the file with…
I needed a directional sign to show guests where the bathroom is in our house when we have people over during our backyard parties. There is both a left and right version. You only need the stands if you plan on putting the sign on a…
UBBI - Universal Bidirectional Bowden Interconnect - Spacer
I hung up a clothes line, a singular one. Found out my batches are usually quite large, so i needed a second line. Instead of making 2 new holes to hang the line, i simply anchored one side and changed the direction so that I had it in a…
Lengthened neck to make it work with most talon blasters comfortably as well as a mirrored catch making it ambidextrous/ omnidirectional Lengthened neck to make it work with most talon blasters comfortably as well as a mirrored catch…
MONO a fore foot (ball) shoe hold between your toes So first this isn't the shoe to walk for hours. It is when you have slippers at the door and annoyed that they always facing the wrong direction ( sure you also can leave them at 90° )…
This is a proof of concept of a printable two-way clutch. Feel free to improve/remix this idea. The clutch is freewheeling when the lever is not engaged. When the lever is engaged, it drives the output gear in the same direction as the…
The mount was created to accommodate the original arrow, with a recess to pass the cables without disconnecting the connector and a guide to be able to fix it with a nylon tie. If you want an angle different from the 25° that I used,…
