Liczymy pasujące modele…
I needed a more low profile mount for the DS18B20 to place it inside my enclosure without it interfering with the 3D printer. This design does just that, allowing me to access the printer without the thermometer getting in the way. You…
Direct die cooling is done at your own risk! Noctua cannot be held responsible for any damage that may occur to CPUs or other hardware components when removing the heat spreader and using direct die cooling. Customers can easily 3D-print…
Clamp for connecting DS18B20 to 15 or 22 mm pipe. Used for temperature measuring heating radiator. Best to print with ABS or PETG because of temperature used for the heater. Category: Electronics
Just a simple DS18B20 Temperature Sensor mount. I printed it with PLA but if you need it in a place that gets hot you better use something that can withstand the temperature. Slide the sensor in from the top or the bottom. It has a tight…
Like it? Please don’t forget a like any maybe a follow, thanks a lot. (morg For more Project’s and insights, see my Instagram or TikTok Account (Link in my Bio)
DS18b20 temperature probe holder for probe measuring 6mm OD x 50mm length. Use double sided tape for mounting.
This is an aquarium (or other glass surfaces) mount for temperatur sensors DS18B20 / DS18S20 (6x50mm). the sensor just snaps into the mount and there you go. you need two suction cups (small ones) like the EHEIM 6803…
These Servo-frames are perfect for the KST X10 or similar Servos in same size. Best filament-choice is PET. 100% infill, print time for 2 frames is about 52 minutes.
Climate shield made to hold 1x DS18B20 (waterproof) sensor. Including a mount that fits the railing system inside Juliana Greenhouses and the corresponding bolts/nuts (might fit other greenhouses with similar systems) Needed materials: 4x…
These are holders for the DS18B20 temperature sensor designed to be attached to a water heater to monitor the water temperature. The first holder can be fitted with four 6x3mm neodymium magnets such that it attaches to the stainless steel…
I use a DS18B20 temp sensor to measure the outdoor temperarture in Home Assistant, but my sensor was always dagling loose somewhere. 10 minutes in Tinkercad and voila, a nice smaal wall mount for it.
A simple quick print to mount a ds18b20 One-Wire temperature sensor outside. parts glue together. i printed it in ABS to not deform in the summer sun.
3D printed shield, against overheating of the thermometer in direct sunlight. The doubling of the shield makes it possible to better shield the salve heat from the heated outer shield. Assembly manual
I've designed a simple case for the Rotation LED Clock. The enclosure has cutouts for the lightsensor and the thermometer and of course for the Display. The holes for the Buttons, the speaker and the mini-USB-Port are located in the…
This mount was built for this project: https://github.com/BrobstonCreations/delta-tango Specifically to mount a DS18B20 temperature probe to the outside of an HVAC duct, but poke the temperature probe into the duct. In my case, this will…
Box for temperature sensor
Clamp to hold a DA18B20 waterproof sensor on a 50mm PVC pipe
Simple holder for temperature sensor DS18B20. Fixing with binder strips. Holders for internal diameters 18,20,22 mm For better heat transfer I used a heat conductive pad (blue pad)
A simple DS18B20 mount for sensors with a metal 6mm tubing and wire Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PETG Category: Electronics
DS18B20 holder to monitor the temperature in your aquarium! The model is a holder for a DS18B20 temperature sensor suitable for 5 mm aquarium glass. You can fix the clamping of the sensor with a small screw. The cable can be fed through…
This is an adapter for putting a 60 mm fan into your trusty Rigol DS1054Z oscilloscope inspired by https://www.prusaprinters.org/prints/10300-rigol-ds1054z-converter-for-60mm-fans . I'm using a Noctua NF-A6x25 FLX with their low noise…
This is an Holder for the 6mm DS18B20 Sensor for ZIP Tie and screw montage Photo printed in Prusa PETG orange
Printed in PETG Printed on its Side Uses #4 Screws to mount
Electronics and DS18B20 sensor housing with battery power for outdoor use. The project transmits data by radio over mysensors protocol. The sensor is powered by a single 18650 cell which is easy to replace thanks to the unscrewable bottom…
Stand to hold a Uniden SDS100 Scanner upright, tilted back 15 degrees to aid in reading the display.
Remix of @Tom_62253 excellent Stevenson Screen. I wanted the base to be a little more lighter weight and specifically hold a DS18B20 temperature sensor. I also wanted a simple wall mount to screw it to a flat surface. Fits this sensor…
This is a remix to put them all inside a case.
A simple mount for the waterproof DS18B20 temperature sensor. I've mounted this to the inside of my Ikea LACK enclosure, as I'm currently working on a heated chamber design. The temperature sensor holder can be mounted with a single…
NodeMCU case with lid, DS18B20 doesn't contact with model.
Wall mount holder for any 1-bay NAS.
This is a simple drop in 20mm ball mount for the Uniden SDS100 Scanner. I needed something to use with the 20mm Bulletpoint Mounting Solutions system. This mount can be left in the vehicle while the device itself can be pulled in and out…
This is a mounting bracket that holds a JSN-SR04T ultrasonic sensor and waterproof DS18B20 temperature sensor for mounting to a 1" square tube. This is part of a project to measure the water level of a creek. The sensor will be extended…
Adapterplate to fix the DS18B20 one-wire thermistor inside the chamber of a Voron V0. The adapter will be screwed on top of the z-rail extrusions, the wire will be routed through the hole on the right side of umbilical PCB. The thermistor…
- Outdoor holder for DS18b20 temperature sensor - The height can be easily adjusted by adding or removing the number of center rings that are simply screwed together. - The hole for the sensor is modeled narrower because some sensors have…
I was able to acquire a Ryobi WDS1600 drum sander for super cheap due to a broken gear. This gear replaces the main drive gear that interacts with the drive shaft. Only time will tell how long a 3d printed gear will work for this…
These are some short feet for a Rigol DS1054z (or any, I'm guessing, in the 1054 family). I had been using some taller feet that were great, but the extra height got in the way of my tool storage wall behind it. These slip on easily over…
This groove mount can be used to mount a DS18B20 temperature sensor inside your Ikea LACK enclosure. My previous design made it quite difficult (i.e. impossible) to remove the 3D printer from the enclosure when installed. Therefore, I…
Just another DS18B20 Mount. I needed such a mount for my heating pipes but couldn't find one. So I simply designed that mount, which holds a DS18B20 in place with 1 or 2 zipties. I used shrink tube on the lower part to hold the sensor in…
This thing allows you to mount a 60mm fan inside the DS1054Z. I used a Noiseblocker PR-2. Now it is silent. One edge needs to be removed. Otherwise the fan pushes against a pin header on the main PCB. Print instructions Category:…
Together with my kid we made this case for his DIY clock (soldering project). The clock we have is from here: https://www.roboter-bausatz.de/p/bausatz-rotation-led-uhr-ds1302. Additionally, it requires: 5x M3 brass inserts 4x M3 6mm SHCS…
I converted my home HVAC system to be run by Home Assistant, and conveniently had space on the esp attached to the furnace for a temperature sensor in the adjacent cat/laundry room. Thus, a low-profile, supportless, snap-in ds18b20 mount…
I built this EC1515B clock kit several years ago and it has just sat around without a case ever since. There are other 3d printable cases out there for these clocks, but me being me, I wanted something unique. To my knowledge, no one has…
About the print This print is part of a larger project I am working on to implement Mycodo into my hydroponic garden. The goal is to have several modules that can connect independently, with ‘break out boxes ’ for different sensors,…
I would like to see how other people made and use this for themselfs, a ‘make’ would be very nice. Thank you.
With this clip, a TO-92 IC e.g. the DS18B20 sensor can be used as a mooring sensor. It improves the mounting by means of cable ties.
Simple and easy2print stand for a DS18B20 Dallas Temperature-Sensor. This is for the 7mm water resistant ones. No supports needed. Used in a green house to monitor the temperature on the ground.
First Special thanks to MirageC a wonderful design. I Remixed the design of MirageC for my requirement This project is very helpful for pre-heating our 3D printer filaments. The main aim to remove the moisture level of the filaments which…
This mounts a DS18B20 probe on a 2020 or 3030 profile. You can attach it parallel or at a 90° angle. There's two halves to prints, so that makes for 8 files. Assemble with two 2mm x 10 self tapping screw screw and a ziptie. If the probe…
the scanner guys sds100 stand
A simple slide in holder for a DS18B20 temperature sensor, like these: https://www.amazon.com/gp/product/B0924NBNZP
Remix of the Original holder, smaller distance between wall and cone and smaller screws
Simple probe holder for 2 probes (DS1052) just glue to the side of your scope This probably won't work if you still have the yellow tips at the end of the probes, you will need to modify it to make holes bigger
These are probe holders for Rigol RM-DS1000Z rack kit. 4x M4x12 or M4x14 countersunk screws are needed for mounting. Designed for RP2200 probes.
The signal generator is a useful tool for the electronics enthusiast's work bench. You can spend a lot of money for a powerful signal generator. The UDS1000S series of signal generators are feature rich and low cost. The module is readily…
Microcontroller case with lid and a separate section for the DS18B20 temperature sensor. Prints perfectly on Ender 3 Neo, with 0.2mm layer heights, only the lid need supports for the 4 legs. Printed in like an hour
O'scope came with 4 color bands, none of which matched the dark-blue of channel 4.
Small mount / stand-off for a common metal-encapsulated DS18B20 temperature sensor. I use two of these, monitored by Octoprint, to watch temperatures of the enclosure and a filament dryer. Base has a recess for an M3x8 nut; use an M3x6…
A simple case to hold DS18B20 Temperature Sensor that uses 6x3mm magnets that snaps together and magnet cable management. no support, .2 and 15% infill
This is a mount for a DS18x20 sensor for ventilation temperature monitoring
Remix of the original holder , but with a foot with magnets for attaching to a metal sheet windowsill. Using six 5x3 millimeter magnets. Print the top and and three of the middle thing and glue together. Insert and glue magnets.
I built this digital clock from a kit and needed an enclosure. So i made this. This is the clock-kit: https://www.roboter-bausatz.de/p/bausatz-rotation-led-uhr-ds1302 Category: Electronics
When you use the retractable feet to tilt the instrument, the oscilloscope tends to slip or the feet collapse. With this model, you have the same angle as with the retractable feet, while the entire instrument is stable. You can also…
Designed this little tool to mount the waterresistant DS18B20 (7mm stainless-steel version) on top of a Capacitive-Soil-Moisture-Sensor to watch the earth temperature and the moisture level via IOT in the flowerpot on the balcony. With a…
I was struggling finding an appropriate spot near my couch for my portable scanner. I designed this up in fusion for the radio and other storage for a can. Could probably scale up 1% for a little more room as the fitment with the radio is…
Simple print, these two brackets give the scope a slight downwards angle so that it can be mounted higher up (I have mine over my monitor). The scope clicks into these brackets and is very firmly held in place. Let me know if you like…
The enclosure has two mounting holes and a DS18B20 sensor holder in the center. It also has four holes for running the cable inside the enclosure, so it won't be visible outside the enclosure. I recommend printing with PETG or ABS. I've…
A quick little case to hold a PSU and ESP8266 (D1 Mini) for monitoring the temperature of the hot water cylinder for my home automation system. The PSU came from BangGood:…
This clock housing is designed for wall mounting od DIY DS1302 Clocks ( https://de.aliexpress.com/item/4000311133709.html ). The USB Plug can not be used anymore, instead 2 wires need to be soldered to the appropriate power holes. There…
A DS18B20 Thermal Probe Mount I made to hang them in my attic. The two holes are for mounting. The probe snaps into place in the front and is secured with a zip tie, and the wire is secure with a zip tie as well for strain relief. The…
The DS1 diameter sensor is an ARTME 3D® kit for building a sensor to measure filament diameters ranging from 1.5 to 2 mm. The kit is supplied with all the necessary components. Only the 3D printed parts need to be printed yourself and…
Dallas DS18B20 temperature sensor cover 1x - M3x10 screw
Small Housing (50mmx50mmx14mm) for the Loxone 1 - Wire Temperature Sensor https://shop.loxone.com/deat/product/200109-temperature-sensor-set-1-wire There is one version with a clamp to hold the Sensor made by Loxone and another one…
The design (remix) allows replacement of the rather loud 24V power supply fan with a Noctua A6 60x25 and a Dallas DS18B29 temperature sensor used in conjunction with the ESP32 and more ESP32 controller board. This board allows temperature…
Not my original design but can't find the original anywhere, please let me know and I'll update the model settings for correct attribution.
DS18B20 sensor holder with 8x4mm magnets
I have adjusted to Hydroponic Tower Filling Module to accept the 6mm Sonoff DS18B20 Temperature sensor https://itead.cc/product/sonoff-ds18b20/ The DS18B20 sensor just snaps in place but I have extended the two internal mounting tabs if…
TDS sensor + DS18B20 thermal probe holder
I wanted to make a compact enclosure to hold my D1 mini thermometer for monitoring temperatures for my pond. This enclosure is tough and compact. Uses hot glue to hold the board in place, and to hold the thermometer cable in place as…
Note: If you choose to make one for yourself, then make sure you buy the three-button, SMD LED type. Otherwise, it probably won't fit the case! I picked up a pre-assembled DS1302 (or, "DS just after lunch" as I call it!) clock module from…
Replacement in case you break the tab off like I did Designed for: https://shop.homeseer.com/products/z-wave-door-window-sensor HomeSeer HS-DS100+ Z-Wave Door / Window Sensor
Got tired of accidently pressing the AUTO button and decided to do something about it.
This model goes with my DS18B20 (Waterproof) Temperature Sensor Mount and fits over the sensor to keep it out of direct sunlight and or rain.
A simple set of models to make a stevenson screen. These slide over a 6mm Dalas based temperature probe cheaply found on ebay. For more information about Floaty McFloatface, from which this thing is from, visit…
HOLDER DS18B20 FOR PIPE
Temperaturmessstation Hier ist der Link zu den Platinen: https://www.pcbway.com/project/shareproject/Temperaturmessstation_34478d1d.html Und hier könnt ihr selber Platinen bestellen: https://www.pcbway.com/ Temperaturmessstation mit LCD,…
This is a reproduction of the speaker cover for a Citroën DS19 made with FreeCAD. The original piece is the brown one and the reproduction is the orange one (do note that the photo display an old version, printed in draft. Since then, I…
Introducing a purpose-built base designed specifically for mounting the DS18B20 Water Temperature sensor with precision and stability. Crafted with attention to detail, this rectangular base provides a secure platform for seamless…
This design is made to accommodate a Samsung PS-DS1 speaker, but any other speaker should work as long as its smaller than 88mm x 72mm (width x depth). You will need a 1 inch (External diameter) tube (in my case Aluminium). It's designed…
A Klicky Dock with integrated DS18B20 Mount for the Ender NG 1.2
Designed to mount DS18B20 temperature sensor on interior shelf rack rail for Frigidaire. Printed with 0.15mm layer height, hooks facing down on build plate with supports.
This is the back plate I've been using for a year now on my ratrig vcore 3.1 300. Some visible holes are not completely drilled to optimize the rendering when printing the first layer. It is designed to accommodate the cpap cage (remix).…
This clip will hold the DS18B20 temperature probe 90° turned on a 3030 extrusion.
Simple Housing for DIY LED Clock DS1302 Link: https://www.roboter-bausatz.de/1719/bausatz-ds1302-rotation-led-uhr The Base is 2mm smaller than the Front to put a little Bit pressure on the clock The Base_Wide should fit without pressure…
MoleBox system - 3D printed boxes compatible with BITBEAM construction kit (therefore even with LEGO Technics/Mindstorms). The main purpose of MoleBox is covering a particular sensor or the entire module and simultaneously allowing…
Case for D1 mini and ds18b20 sensor
If you like this model and use it please upload a like, it really helps others find it! I hated having my scope on my desk and the cables getting in my way, especially when not in use, and I already had a “portable” touch screen mounted…
