Liczymy pasujące modele…
V ČR osazuje tento modem T-mobile, zejména pro zákazníky mající zájem o připojení pomocí transparentní bridge. U modemu není řešeno uchycení na stěnu, doporučuji umístit větracími otvory ode zdi i když je počítáno s větrací mezerou při…
Absolutely awesome work from MartinRowan . I wanted to put my fiber optic modem on a sled. Used the provided blank sled .step file and made this sled. I'm including the first iteration I made and the final iteration. Initial: Full sled,…
EN I designed this sliding cover so that the lights of the Vodafone ConnectBox (Compal CH7465) don't disturb my sleep. Preferably in dark filament so that no light gets through. When attaching it, press it down evenly so that no layer can…
The TPLINK TFC311B20 does not have a Wallmount option. So here is one. I heard this TP Link Model is requiered in some areas.
This is the wall mount for a Lite 16 PoE USW-Lite-16-PoE (45W) modem. you probably threw it away with the packaging, here's a replacement
I wanted to rack-mount my cable modem, but these models are slightly taller than 1U, which requires removing the factory enclosure and retaining only the PCB and rear panel. This replacement case is designed for passive cooling, as my…
This is a 2U 10 inch rack mount for assorted Spectrum modems. I don't have an exhaustive list of every model that it will fit, however if you modem has this shaped housing it will likely fit. Printing This model requires a minimum of…
Simple case for a LTE modem module. The both halves hold together by 5 M2 heat inserts in the bottom and 5 M2 screws.
This MultiBoard Holder is made for a Usb MultTech Modem/Fax that I have connected to a RaspberryPi 4 that uses HylaFax+ to receive and send our faxes. I used a 0.2 layer height, and a 5mm brim. Thanks to the tools at Makerworld.com to be…
This bracket allows you to secure a Hitron CODA-5610Q cable modem to a wall. This is one of the modems used by Fizz in Quebec. Design features The bottom bracket is in two pieces to save material, and each side (left & right) has a short…
This Skadis mount is designed to hold the Telekom fiber optic modem using its integrated wall mount. To attach it to the Skadis board, print two T-Clips from the original Skadis clip design that matches your board type.
Rack mount for Nokia Fiber Modem, which provides easy access to the connectors, while keeping the LEDs visible as well.
DESCRIPTION TL;DR A quick print to help you position the Play modem horizontally. Key Features low filament usage sturdy design allows to attach fan, external drive or cable managment using heatinserts MAKING Requirements This is an easy…
Honeycomb Storage Wall mount for your AT&T BGW320-500 fiber modem! I took inspiration from Plexi 's earlier design and mimicked it while adapting it to Honeycomb Storage Wall. Each part is designed to be printed at a 45 degree angle to…
Use screws from original base to mount modem to brackets once they are on the wall. Use M3 for wall screws, spaced 135 mm center/center. Recommend printing brackets on side for strength with supports (touching base only). Can print…
Use this rack mount to clean up your set-up. The Rack is 1U in size and fits 19-inch racks. If the fit is a little too tight simply scale the parts by 1 or 2 % in only the tight direction (do not scale overall or it may no longer fit the…
Discover a functionally designed 3D model specifically crafted to securely hold Telstra Gen 3 Smart Modems. It boasts a small lip that ensures your modem stays in place firmly despite the weight of hanging cables. Creating this model…
This is a small shelf for a router to be fixed to a wall Print Settings Printer Brand: XYZprinting Printer: da Vinci 1.0 Pro 3in1 **Rafts:** Doesn't Matter Supports: Yes **Resolution:** 0,3 mm Infill: 15 to 30 **Filament:** Azure film…
This wall mounted bracket is for an AT&T BGW320 Fiber Modem. It allows you to mount your modem on the wall securely. It includes the mount shelf with retaining tabs, a top clip, and an optional power supply mount which clips to the…
EN I designed this sliding cover so that the lights of the Vodafone ConnectBox (Compal CH7465) don't disturb my sleep. Preferably in dark filament so that no light gets through. When attaching it, press it down evenly so that no layer can…
The TPLINK TFC311B20 does not have a Wallmount option. So here is one. I heard this TP Link Model is requiered in some areas.
This is a drop-in replacement enclosure for the original Vigor 167. The modem uses a single PCB, so the swap is quick and straightforward. Handle the PCB with care, there’s a high-voltage section with its own protective cover. make sure…
Recommend slightly higher infill, e.g. 30%. Supports not needed. Try to use self-tapping screws within 7mm total shaft length. Current model uses a inward-drafted 2mm diameter hole, with modelled penetration depth up to 6mm. Modify with…
My modem was on the ground and I just want to wallmount it and there was no wallmount holes in the back of modem and I created this model to improve cable management.
This is the wall mount for a Lite 16 PoE USW-Lite-16-PoE (45W) modem. you probably threw it away with the packaging, here's a replacement
Rackmount for LM1300 LTE bridge using the esrack system
For mini rack like a deskpi, this holds an Arris cable modem.
Evime fiber ağ bağlattım ve böle bir raf ihtiyacımız oldu umarım sizin de işinize yarar. Solidworks çizimini de birleştirerek ihtiyacınıza göre değişiklik yapabilirsiniz .Ben Pla malzeme ile bastım. Yatak sıcaklığı 60C Nozul sıcaklığı 230C.
I measured the mounting feet on the modem and made some feet that securely slid in and locked in place, then put it on a random L bracket I found. The antennas should be facing a certain way, so it's not just mounted to the wall at a 90…
Stand to vertically orient a DZS Fiber Modem, specifically made for Model ZNID-GPON-2424A1-NA Rev H. When I switched to a new internet provider, the modem they provided was designed to sit horizontally on a surface, taking up a large…
Introduction I've been printing a bunch of ESRack things for my work and home racks and I've always wanted to rackmount these annoying cable boxes. Unfortunately they have a case that's almost exactly 1U high, so the standard ESRack…
Rack mount for the Motorola MB8611 / MB8600 / MB7621 cable modem, with ventilated shelf and keystone jack. Also has a screw mount hole to mount the modem directly to the modem tray. You must remove the base/stand of the modem in order to…
Small 240x125mm shelf for a router or modem that can be hung on a 19mm wide ledge. You'll need 4x M3 square nuts and 4x M3x8 or 4x M3x10 screws ; grab them from the printer's spare bag if you still have it. Installation: Put the nuts into…
1.3U rack mount for the Motorola MB8611 / MB8600 / MB7621 cable modem, with ventilated shelf and keystone jack. Also has a screw mount hole to mount the modem directly to the modem tray. You must remove the base/stand of the modem in…
Print in PETG with front facia on the bed, and with supports - Prusa Slicer Snug is the best for this. Please see the comments section for some important details discussed. The tl;dr is - the stubby leg things that protrude out the bottom…
Mount for a MicroSD card extender that fits into the modem slot of PowerBook 1X0 (tested in a 180)
For assembly required items: M3x20mm screw x4 M3 nuts x4 M4x15mm screw x2 M4 nuts x2 Support is required only on the base place under the two buttons. It can be left in place and does not need to be removed.
I really liked the original ESRack system design created by @EvilProphet . I created a customized a module to hold my specific modem. I have it sticking out from flush intentionally so you can see the status lights on top. If you would…
Helps you to keep your workplace tidy without having your modem/router on plain sight. The case is 165x50 mm and 10 mm wide. Has two 3mm diameter holes that can be drill for bigger screws.
Supports not needed for pegboard mounts, but you may need it for the small screw hole.
More Informationen Coming Soon. First Version! Material: PLA Nozzle: 0.4 mm Layer height: 0.2 mm Important information for disassembly: There are 2 screws under the 2 rubber feet that go towards the connections. Attention! Do not bend the…
Holder I designed to mount my Orange Siligence modem to the wall. After losing the original mount, I decided to make myself a quick alternative. Printed in Eryone PETG with additional walls for more strength, but this should not be…
This is a simple scaling up of the original to match the wider mount points of the XS-020X-A ONT device. Be careful when pressing the device to lock in as the studs for the mount are not super strong.
14mm pipe/stick and pipe clamp are not included. Find or make a clamp that fits your needs, I can not make it for all kinds of pipes. I have added 60mm clamp with 14.5mm holder for 14mm pipe/stick and an extender. Make sure to have very…
After experiencing several issues with overheating on my Xfinity XB modems, I found that the airflow to cool the device was lacking. Through trial and error, I made several ad-hoc stands to find the right height to allow for the necessary…
I am using a 10" mini rack and couldn't find something I really liked so i cut the ESRack mounting mechanism off this and slapped it on a standard 10" mini rack mounting plate.
Printed on Modified Creality Ender 3 All 3 parts in single stl file Use your slicers “split parts” function to divide them Made with onshape:…
Use the split-into-parts feature in Bambu Studio to print in multicolor.
Use the split-into-parts feature in Bambu Studio to print in multicolor.
Spectrum Modem 10" (10 inch) Rack Mount Bracket Should be compatible with the following models: E31N2V1 E31T2V1 E31U2V1 EN2251 ET2251 EU2251 In order for this to fit on my print bed I removed half of the front face of it and created a…
Just a simple stand for ZTE outdoor modems. Keeps the modem upright on a table or windowsill. Designed for a ZTE MC889A, but I believe the dimensions are the same on models MC7010 and MC889. Do check before printing, though; the…
A cooler for the Arris S34 modem , not sure if it fits anything else. Uses 40mm fans (I used these ) for additional cooling. Should just slide on to the top of the modem when upright. Print using supports. I printed mine in ABS, but other…
I found the original model https://www.printables.com/model/689610-wall-mount-for-hitron-coda56-cable-modemhttps://www.printables.com/model/689610-wall-mount-for-hitron-coda56-cable-modem functional but too flimsy. I added a support beam…
The position of the command strip ensures the load is mostly in shear; this allows for holding a much heavier device without the risk of release. 2 Sizes are included; the large one fits 2 command strips and can easily hold an RAXE500…
A light weight wall bracket for the Hitron CHITA Modem the Virgin Media supply for their business fibre broadband. It's somewhat annoying that a “business” product has literally no mounting options other than free standing, so to address…
This is a simple and practical stand designed for DU SIM card modems. It slightly raises the modem to improve airflow and cooling efficiency, helping prevent overheating during long use. The stand has a clean, minimal design that keeps…
It is a simple device designed to fix the ZTE brand modem by hanging it on the wall and can fit on many printer tables.
Notes This case does not support the Wi-Fi antenna this modem comes with. (I also ended up not needing the “left ear” part in my installation.) Tools for the teardown T10H “Security” Torx screwdriver #2 Phillips head screwdriver Spudger /…
The case is a simple rectangular case that is designed to fit my XIDOL K5188 USB modem I bought from Tokopedia. The device seems to share the same dimension with UZ801 or other chinese USB modems. The “Zhihe-series LTE dongles” page from…
This mount will allow you to attach a Motorola cable modem (models MB8611 / MB8600 / MB7621) horizontally and store in a 10-inch networking rack. Unscrew the base from the modem, lay on its side and attach screws through the side of the…
DreamPi All In One Box for Dreamcast Pi Modem Adapter Hold all parts and allow having only the modem cable and power cable for a cleaner desk. Allow using the hdmi port if needed. You'll need : Modem splitter - be cautious that there is 2…
Suporte feito para prender 2 modens de fibra diretamente nos trilhos fixos de switchs
Wall and desk mount suitable for Neterbit NWR-940X modem with 0.6mm internal space margin. It is best to print with PLA filament. The screw required for the wall model is 3mm in diameter and 5mm in cross section.
The original model didn't fit well with my cm3000 modem, specifically the cable hookups. so rather than just drill a hole like a normal person, I redid the whole darn thing in CAD. Now your modem can gain 0.02 horsepower from all the…
Unser Haus wurde mit FTTdp (firbre to the distrebution point) ausgestattet. Mein Provider stellte mir ein FTTdp Modem das nun zwichen den Router und dem Anschluß geschaltet werden mußte. Da der Platz an der Wand langsam knapp wurde habe…
This is a simple, easy-to-print modem cover designed to blend more naturally with your home décor. The model is sized to fit modems of 12 × 12 × 22.5 cm. The panels are modeled as solid surfaces, but they must be printed with top and…
I changed the screw hole size to 3mm, as those are the only screws I had. I've also included the step files in case anyone wants to modify the mounts.
The pigtail antenna cable support model for ZTE USB modems may also be suitable for Huawei. Protects the connector for the external antenna and pigtail connectors from fracture and excessive mobility. If desired, the panel can be glued to…
Simple mounting bracket to allow mounting an Actiontec DSL modem with double sided tape (command strips, etc).
I wanted to rack-mount my cable modem, but these models are slightly taller than 1U, which requires removing the factory enclosure and retaining only the PCB and rear panel. This replacement case is designed for passive cooling, as my…
This is a 2U 10 inch rack mount for assorted Spectrum modems. I don't have an exhaustive list of every model that it will fit, however if you modem has this shaped housing it will likely fit. Printing This model requires a minimum of…
Simple case for a LTE modem module. The both halves hold together by 5 M2 heat inserts in the bottom and 5 M2 screws.
Simple case for a LTE modem module. The both halves hold together by 4 M2 heat inserts in the bottom and 4 M2 screws.
This MultiBoard Holder is made for a Usb MultTech Modem/Fax that I have connected to a RaspberryPi 4 that uses HylaFax+ to receive and send our faxes. I used a 0.2 layer height, and a 5mm brim. Thanks to the tools at Makerworld.com to be…
This bracket allows you to secure a Hitron CODA-5610Q cable modem to a wall. This is one of the modems used by Fizz in Quebec. Design features The bottom bracket is in two pieces to save material, and each side (left & right) has a short…
This Skadis mount is designed to hold the Telekom fiber optic modem using its integrated wall mount. To attach it to the Skadis board, print two T-Clips from the original Skadis clip design that matches your board type.
Rack mount for Nokia Fiber Modem, which provides easy access to the connectors, while keeping the LEDs visible as well.
DESCRIPTION TL;DR A quick print to help you position the Play modem horizontally. Key Features low filament usage sturdy design allows to attach fan, external drive or cable managment using heatinserts MAKING Requirements This is an easy…
DESCRIPTION TL;DR A quick print to help you position the Play modem horizontally. Key Features low filament usage sturdy design allows to attach fan, external drive or cable managment using heatinserts MAKING Requirements This is an easy…
I want to use my outdoor modem that is supposed to hang on the wall on my desk. So I designed a stand for it I used a PLA to print
This mounting bracket is designed specifically for the Hitron EN2251 cable modem, providing a clean and secure way to mount the device to any flat surface such as a wall, cabinet, or structured media panel. The design holds the modem…
Honeycomb Storage Wall mount for your AT&T BGW320-500 fiber modem! I took inspiration from Plexi 's earlier design and mimicked it while adapting it to Honeycomb Storage Wall. Each part is designed to be printed at a 45 degree angle to…
Un support simple permettant de fixer le modem Bell Home Hub 4000 / Giga Hub/ Virgin Vincent / Sagemcom Fast 5689E sur les panneaux Ikea Skadis. Utiliser le Twist Clip / Tclip
Telekom Glasfaser Modem 2. I measured the mount and modeled it based off of the wall mount that comes with the modem. There is also a model with a flat bottom. If you print it it should fit fine. Just be careful with the little tabs for…
Partially enclosed shelf for a Shaw Fibre+ Gateway modem 2.0 (XB7). Also works for Comcast XFinity TG4482 / Arris. Printed with PETG, 20% infill, no supports needed. Suggest adding a cylinder modifier around the screw holes to strengthen…
Sturdier remix of @loopj's MB8611 Rack Mount with LED light pipes and an SVG for laser etching the face. Wider gussets to reduce flex LED window removed and replaced with light pipes SVG for etching the face with the logo, LED icons, and…
Simple remix of invictus0x0's design but with: larger, rounded corner window to allow the status LEDs to be more easily visible a simple facet around window boundary to further increase visibility from more angles slightly larger hex…
FYI the fit on this isn't great - I noticed recently the measurements have been off for this model as well as others (not sure if it's always been that way or if Arris switched things a bit). Use this new model instead…
This bracket allows you to wall mount a Shaw BlueCurve cable internet modem. (Technically the ARRIS Wireless Gateway TG4482) Generically: Technicolor | CommScope CGM4331SHW | TG4482. AKA: Fibre+ Gateway 2.0 (XB7) Mount to the wall with #6…
This stand uses an 80mm usb fan in the bottom and blows through the top. Fan https://www.amazon.com/gp/product/B00G059G86/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
This is a mounting bracket for the ARRIS SURFboard SBG6950AC2 16x4 DOCSIS 3.0 Cable Modem. I got mine from Amazon . I printed it with 4 shell layers, and 50% infill. You'll need some sort of drywall anchor if you're mounting it on…
Simple cartridge stand for a Commodore VICModem. Category: Electronics
Summary I've got a small networking rack, where my router and switch are located. I've also got an NBN HFC modem, (a DOCSIS cable modem), this is produced by Arris for NBN Australia, but their enclosure is used across many different…
