Liczymy pasujące modele…
Simple replacement latch for an ArtBin model number 83805. PETG is suggested for a mixture of strength and flexibility. Support everywhere is required, but easy to remove.
Wydruk około 0,33 €–0,40 € nettoWstępna wycena dla PETGMateriał u źródła: PET
My mower cap broke so ive designed a new one to 3d print. Thread has a 3 mm pitch with an internal DIA 46.5mm. I printed this from PET-G .12 layer for smooth threads. no supports needed. If you print one let me know.…
The original 3D model was too small, measuring 18mm in width. For the Alloy FPS model, the foot measures 25mm in width.
It works with the HyperX alloy origins, but it should also work with other HyperX keybaords. I would recommend using a smaller layer hight, like 0.2 or 0.15 and use for material PLA or PETG, but it should work with all solid materials.…
Simple replacement latch for an ArtBin model number 83805. PETG is suggested for a mixture of strength and flexibility. Support everywhere is required, but easy to remove.
Wydruk około 0,33 €–0,40 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I lost my original mixer/blade for my 500ml Tupperware Quick Shake. Print 3+ perimeters, 100% infill. I recommend printing in PETG ; “food grade” PETG filament is even better.
Simple replacement handle for an ArtBin model number 83805. PLA works great.
Most of these pieces are NLA or have a long lead time from Mazda. all the bushings are quite straightforward. Print solid from a heat resistant plastic like ABS or PETG. Bushing 2 there are 2 variants, one with threads and one without.…
This model serves as a replacement part for the Logitech Group camera mount. If the base breaks off due to a fall, it can now be repaired.
Feet/stand for Bose speakers, inspired by the 2000s Y2K aesthetic to match the style. Printed in a cheap semi reflective PLA (Amazon PLA). I recommend using variable layer height for the neck part to add a bit more rigidity. However,…
Pin has to be removed from the bell and at least a m4x35 has to replace it (i used a countersunk bolt). the bell neck can be threaded by the bolt, but to make it extra secure i added a nut (M4) to the bottom. You might have to alter the…
small model i recommend 8 perimiters for strenth purposes and super glue during assembily only supports needed under the large bridge but only on the tip as long as your printer can bridge a few mm the tubes going from multipule parts of…
Printed on: Creality ender 3 V3 KE. Filament: PLA Layer height: 0.08 mm
My kids lost one of the "number 2" blocks, so I made a replacement. Category: Toy & Game Accessories
This is the inner foot for the K8. The model itself should be dimensionally accurate, but I had to print mine at ~95% scale to get it to fit without breaking For outer foot see:
I was unable to find a model of this specific design to match my existing slot covers. I previously downloaded a cover from this great collection https://www.printables.com/model/219169-pcipci-e-slot-covers-10-designs but realized the…
Safariland thumb button replacement recommended 4 walls and at least PETG
These are replacement tires for the I7 and J7 Irobot vacuum using 83A TPE filament. I suggest using the irobot tire 2.11mm v9 version but I included my other designs as well.
This is the back part of the Rear Air Vent Knob of Skoda Superb 3. This part cannot be bought separately or ordered from any site. But some absolute chad and a god named Camarao69 from briskoda forum created a replacement. I am uploading…
Replacement tokens for monster weaknesses from the “Monster Weakness and Special Attacks” module* for Witcher Old World board game. *This module was avaible in KS campain only, i think.
Hey All, not sure what model this is but the adapter on our Dyson broke so I designed a replacement. Both parts need supports. The button was originally designed to be printed face down but that made the tabs on either side prone to…
A squirt bottle replacement Outer thread diameter of 23 mm Recommend 3-4 outer layers to ensure no leaking. Top came off of small squirt bottle.
Replacement for wobbling cat toy with long feather wand. Heating the end of the thin rod where the feather is mounting and pressing it into the top center of the part helps it to stay secure.
Replacement leg for a UV nail light. Printed in white PLA, Best results when printed flat It is a tight fit when mounting them so heating up the locking part that connects with the light on the print before placing it in helps.
Fits a standard box fan, just simple place the width of the box fan in the gap between the feet. Can attach using glue or by drilling two holes and attaching with fasteners.
Name for model custom phone/cord holder replacment
add 18 blades replacment for 40mm fan,iff you broke it and you are poor as i am
I designed this replacment because a little plastic thing had broke over time:/ Reccomended settings 0.25 or 0.4/hf nozzle 3-4 perimeters 20% Gyroid infill ASA or PETG Other notes for Prusa printer owners Use the satin sheet
A cheap computer mouse replacement (Nothing too special)
It can hold a lamp, microphone, and everything else that has a mounting “clamp” to the desk and has a rod that slots into the mount. Ideally should be printed in PETG, although if your lamp is light, PLA could work too. For PLA I…
This is a printable version of the Front Bumper for the Carrera RC Passion Impact 2.0. The Original Replacement part is 370411303. I created this because the Front Bumper broke at the first run of the car, and I think if it is so…
This is essentially a 3d printable version of this part, mine wore out and I didnt feel like paying $15 AUD for a small piece of plastic: https://www.thevisorshop.com/en/au/AGV-Click-Visor-Mechanism-Clip-K6/m-38291.aspx?gQT=2 I printed in…
2 part TPU base to replace the ruvver one. Also i added a internal plc tube cap to prevent the sharpe tube edge from cutting into the tpu foot. fits OasisSpace Shower Chair and other common aluminum tube seats. https://a.co/d/iKpqv65…
19 inch pull wheel for v-belt drive on bandsaw or other belt drive tools. Printed in OVERTURE Tough PC Filament on Bambu X1C 0.6 nozzle Printed with 6 walls and 4 top and bottom 25% rectilinear infill printed in 4 parts to fit 250mm beds…
Made for a 30cm pan , I believe it will fit others as well Print however you'll like, maybe a 0.1mm wouldn't be a bad idea.
great fit and a good replacment for the long destyroyed feet on my small generator. just soft enough to dampen vibrations, and more than hard enough to support the weight I used oveture 95a tpu 75% infil to print these you will need to…
I lost my original mixer/blade for my 500ml Tupperware Quick Shake. Print 3+ perimeters, 100% infill. I recommend printing in PETG ; “food grade” PETG filament is even better.
Needs to be printed vertically standing with supports for the side with hole.
I didn't like the nozzle cover that came wih my EZ Pour so I modeled and printed this knurled cap. Tolerances are fairly tight to keep the vapors at bay. Would recommend printing in something gasoline resistant like Nylon or PA6-GF or…
Print settings: first layer height - 0.2mm layer height - 0.25mm perimeters - 14 @ standard extrusion width 0.45mm supports on build plate only supports type - snug material - PLA or PETG
Simple replacement handle for an ArtBin model number 83805. PLA works great.
This is replacement feet to protect you floor from being scrapped up. Printed with a .4 nozzle, .16 setting using Overture High Speed TPU. This is a very tight fit for my stool, you may need to resize to fit your particular application.…
Replaces the central roller and tape attachment point in roll up tape mesures.
Replaces the end of the handle on roll up tape mesures
I had a broken Horizon Chroma Blade drone model #blh8860 and it crashed. breaking the shell, but it is discontinued so I had to find another way to fix it. So I remixed the crossfire 2.0 and added some attachments for the stock drone…
so there was a backplate but without the kickstand
Designed this part after the original on fusion 360. I know from the customer that the part works though I have not seen for myself. Recommend printing in industrial filaments like nylon carbon fiber as the ones in the photo were made…
This is made to replace the rudder on my TigerShark rc boat. You would need to cut the bottom of the rudder off, just above the bearing housing. Then using epoxy and a few nuts and bolts attach the bottom ahlf to the rest of the rudder…
Okay… so one day I noticed my G502X Lightspeeds Mouse wheel wasnt turning properly. It felt as if on one side the rubber was hitting something… But what really happened is: The rubber on the scroll wheel began to stretch as it dissolved……
Replacment foot for helinox camping chair Print Settings Printer: Flash Forge Creator Pro Rafts: No Supports: No Resolution: .1 mm Infill: 100% Post-Printing Take a 1/2 in drill bit, i used an endmill in a drill,down the middle to clean…
You will need to hammer the cap on, there is a retaining lip that you need to press past. Print in something strong like ASA.
This is a full replacment gear set for the lego rc car 5599 / 5600. You have to replace all gears if one of the original gears is broken. The gears are designed with a 0.6 standard gear module. I could not quite match it to the LEGO…
Print in Clear PETG and I added light grey layer lines that are thicker at the bulb hole side and the stripes get thiner as they get move down to about half way. Shines great as shown in picture. I broke one of the glass originals while…
Replacement wheel assembly for the lower rack of a Samsung dishwasher, designed to mount onto the original attachment point. Wheel look matches factory design. There are 2 files: SamsungDishwasherSpareRoller.step - wheel only file…
Most of these pieces are NLA or have a long lead time from Mazda. all the bushings are quite straightforward. Print solid from a heat resistant plastic like ABS or PETG. Bushing 2 there are 2 variants, one with threads and one without.…
This part is a replacement for the LISTA single‑drawer safety lock used in mobile drawer cabinets. It restores the original locking function and prevents drawers from opening unintentionally during movement. This model is an independently…
Replacement arm for Accu-tie switch mechanism. https://accu-tierailsystem.com/product/rr-switch-throw-mechanism/ Category: Hobby
This is the replacmentpart of the Skullcandy Crusher Evo or 540 Sliding hinge. It's made to keep al original functions, like slide adjusting the size and swiveling, rotating and even locking and folding the cups. It's made in one part for…
Replacment Keyboard klip for Snarkoon sgk4 Category: Parts
This model serves as a replacement part for the Logitech Group camera mount. If the base breaks off due to a fall, it can now be repaired.
My take on a replacement filament spool holder for the Anycubic range of Kossel printers or any printer that uses 2020 extrusion construction. Should be wide enough to take any 1kg roll of filament. Print Settings Printer: Anycubic i3…
Feet/stand for Bose speakers, inspired by the 2000s Y2K aesthetic to match the style. Printed in a cheap semi reflective PLA (Amazon PLA). I recommend using variable layer height for the neck part to add a bit more rigidity. However,…
A drop-in replacment for Flashforge Adventure 4 fan duct. Print the two parts in PTEG or ABS an glue together with super glue.
I printed one with grid but since the slicer decided to print the grid first id didn't stick to the card and I scraped it off with nails. I recommend checking settings and forcing body of the sd to be printed before grid.
Pin has to be removed from the bell and at least a m4x35 has to replace it (i used a countersunk bolt). the bell neck can be threaded by the bolt, but to make it extra secure i added a nut (M4) to the bottom. You might have to alter the…
A z-limit switch for the Creality ld-002r that is 3 mm longer for use when installing the wham bam flexible build system. There is also a file for a replacement of the regular size z-limit switch. Category: 3D Printer Parts
small model i recommend 8 perimiters for strenth purposes and super glue during assembily only supports needed under the large bridge but only on the tip as long as your printer can bridge a few mm the tubes going from multipule parts of…
Printed on: Creality ender 3 V3 KE. Filament: PLA Layer height: 0.08 mm
This is a replacement screw for OLFA knives. Fits for Olfa L-1 or L-5. Print top side down. The metal insert is supposed to fit snugly. Printed with PLA.
My kids lost one of the "number 2" blocks, so I made a replacement. Category: Toy & Game Accessories
This is the inner foot for the K8. The model itself should be dimensionally accurate, but I had to print mine at ~95% scale to get it to fit without breaking For outer foot see:
A replacement set of jaws for a tap wrench. These are designed specifically for Harbor Freight's 40-Piece SAE/Metric Pittsburgh Tap and Die sets ( https://www.harborfreight.com/carbon-steel-sae-tap-and-die-set-40-pc-62831.html ) -and- (…
This is a replacement for the rubber part on the OEM GameCube controller C sticks. Its an ungrade over the original, much better texture and purchace on your thumb without being uncomfortable like hard plastic ones. print settings: 100%…
When Original Sports key run out of Juice, open and replace battery. This Body can be used to replace old body.
I acquired a neat looking old piece of 80s vintage Sony hardware from a garage sale; a Sony Digimatic Lifetime TFM-C770W flip clock radio! However, mine was missing the special two-piece time/alarm/tune adjust knob. Using the radio tuning…
Replaces easily breaking bucket sensor with a beefy one. PETG recommended. See pictures for compatible model.
i finished this at 1 in the morning so ill try to give at least somewhat of instuctions first SCALE TO 300% and print with 85% infill or more if you are using pla which i made this for when screwing the black part over <- yes very…
Placement plug for arm floatie device. Recommended to print in PETG or TPU. Make sure the plug is tight, and always watch over your child when swimming. Nether this plug or the original device is a life saving device! Use on you own risk,…
This is a knob to replace the knob on a post 2017 weber spirit barbecue I have tested the knob in PLA, and it doesn't soften or heat up after running the barbecue. The tolerances are printable on any printer since they do not require…
This is basically a logo-free pop socket cap for those who want a pure pop socket experience to go with their pop socket. Or, if they want to customize it- it can act as a blank canvas! How to Print Its quite simple... ...all you need to…
This is a replacement cap for a Enviro-Bottle 5 gal jug (3 Gal should be the same). It may fit other 5 gallon bottles Thread go all the way to the top. you may want to add paper seal in the cap to prevent leaks like the originals came…
I think something simmerler to the old hub motor I have can still be found on aliexpress: Promotion 36v 350w Front Eletrica Bike Kit Dgw07 Pedelec Hub Motor For Diy Electric Wheel. the motor uses 30tooth gears, not the more common…
This is a replacement part for the upper upper part of the closure mechanism.
A replacement part for the stand, as the original part breaks easily. Customizable height and clearance. The md_stand_4.stl file is the original height, md_stand_8.stl is double in height. Print Settings Supports: No Resolution: 0.2mm -…
Standing feet replacment for G.SKILL Ripjaws KM780
Hello, My original flexi hose ran away and I had this hose left over from another job (see specs in image) so got some ends made up to be able to use with the vac, one part is the internal part to go inside the crevice / floor tool and…
I made this model in Tinkercad nearly a year ago because I rage quit on my keyboard and broke the feet lol. I'm uploading this model now because I looked up on google to see if anyone has yet to make a decent 3D Printed replacement foot…
Replacement stand for a small Star wars Armada ship with a broken pin. I would suggest gluing the ship to the stand or to use a small hair tie to hold it together.
You can cut up to 4 layers of Nonwoven fabric (spunbond) simultaneously. Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: No Supports: Doesn't Matter Resolution: 0.25 Infill: 8% Filament: 3DPlast PETG Black Category: Sport…
This model was a functional copy of the left arm joint of a folding chair. It is roughly the same size including where the holes in the print are. The original part used rivets but i didnt have any so used a thick wire - otherwise long…
The front Bumper on my brothers rc car broke off, so i designed a spare one. its mountet like the original one, looks a little flat from the front, but its printet super easily.(and is really robust)
Material: PCTG Suport: Yes (I use tree support) Nozzle diameter: I use 0.6 Screws to mount M4 L40 with trapered head.
Simple replacement knob for a dimmer switch. Outside diameter is 38millimeters. Inside diameter is 4 millimeters with a keyhole. I added some pattern on the outside for easy grip. Store only sells complete sets instead of just the knobs.…
