Liczymy pasujące modele…
A sturdy 10-inch rack mount adapter for one or two TP-Link SG1005P. Also works with the SG105. To install the switch, simply slide it in. However, if you already added the rubber feet, remove them before installing the switch in this…
This is a 10 inch rack mount for a TP-Link SG105. I have printed it whit ABS. No support needed, I have added a custom support in the model. If you need a 10 inch rack mount for a different brand or you just need a cover plate I will…
Mount for TP-Link TL-SG105 with cut outs for air vents. Under the mount are two channels for the dc supply cable. Mounting is done with 4mm sink head screws. Print with front facing down.
It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…
This is a remix of this mounting plate by asp55 on Thingiverse. This one has the inserts a bit closer than the original to fit newer TL-SG105 switches. Just use double sided tape or whatever you want to mount the plate and attach the…
UPDATE: 25/02/2025 I have updated the design, to compensate for the MicroSD card in the Raspberry Pi, and also adjusted the end of the router back to fix some occasional XYZ errors while printing. U1 10" Raspberry Pi 4 and TL-SG105 Rack…
I designed this holder for mounting the TP-Link SG105 under my height adjustable desk. I used 2xM3 screws with fitting nut and 2x M3,5x16mm wood screws. I placed the nut inside the Screw-Terminals of the switch and fastend the screws…
TP-Link TL-SG105 10-inch Rack Mount 🖥 Keep your TP-Link TL-SG105 securely mounted in any standard 10-inch rack! This remix adapts the original 8-port TL-SG108 design to fit the 5-port TL-SG105. It adds a robust latch rather than relying…
1U rack shelf for 8 port ethernet switch tl-sg105 print settings: 15-20% infill 0.2 layer height
Wall and ceiling mount TP-link TL-SG105 made in thinkercad 3mm thick walls
Wall mounting bracket for our TP-Link TL-SG105 network switch.
A 6-inch Rack Mount for the TP-Link SG1005P | SG105 | OC200 series. This model is part of a series of 6-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a coffee ;) Print…
An easy way to mount you TP-Link switch to the SKADIS pegboard
------------------------------------------------------------------------------------------------- UPGRADED PARTS AVAILABLE! Click the link to get to V.2 of this part:…
This is a mount for a TP-Link TL-SG105 network switch. This can be used to mount the switch under a desk or to a wall. Printed on an Elegoo Neptune 3 Pro with Elegoo PLA. I used 6 x ½" wood screws for mounting. To ensure a snug fit, the…
You need zipties for the power brick. The switch slides into the mounting brackets and locks itself in place. There is also a version for 19 inch racks:
remix from 6.5 inch rack i dont have device to test this print, use at your own risk If you enjoy my work, please consider support at link in profile.
Tenda SG105 Gigabit Ethernet Network Switch DIN rail mount You can use standard mounting holes. Lock the nut into the part and tighten the screw so that the network switch is firmly in place. Try a few times. You can also use a drill, for…
A 10-inch rack mount for the TP-Link TL-SG105-M2 2.5G switch. This model is part of a series of 10-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a coffee ;) Print Settings…
Wanted to use in my 10-inch rack setup since I need the extra space under the Pi for an errant tall PoE HAT in a 1U rack below where this rack will be installed. I subtracted some of the material from the print model surrounding the…
Mounting Plate for TP-Link TL-SG105 switch. Material: PLA+ Infill: 20% Support: Touching Buildplate
This mount is easy to print, resource friendly and reliable. There is no need to use two handles. But it can certainly add grip security. You can use doublesided tape/something else to make it REALLY tight. I'm recommending PET-G or ABS…
This is a renter friendly wall mount designed for the TP-Link TL-SG105 5-Port Desktop Switch. Add 3M Command Strips (or something equivalent) to the back of the mount, put it on your wall, and hook the network switch onto it. Printed in…
Update 11/18/2024: I have added a version with larger openings for round cables. This is a quick little cable bracket for the TP-Link TL-SG105 5 port ethernet splitter/switch. Bracket will snap or slide into place on the unit. It allows…
Rack10 mount for switch TP-LINK TL-SG105
Print with the wing on the bed.
A 2 part modular 19-inch rack mount for the TP-Link TL-SG105-M2 2.5G switch. This mount is part of a 19-inch modular rack mount system I designed, you can mix and match the modules with other mounts. Take a look at my models here to find…
Notice ℹ This mount also fits the "NETGEAR" and “D-Link” equivalents of the equipment mentioned here, since they all use the same chassis from the same OEM's Accton Technology and Delta Networks .Notice ℹ This mount also fits the…
Vertical stand for the TP Link SG105 switch. If your printer is perfectly accurate this should be a decently tight fit. Very stable with a small footprint. Also included a cut out notch as it appears the SG105 has air vents on the sides…
A lightweight bracket designed to hold the TL-SG105 TP-Link Desktop switch. Can be mounted to any flat surface, wall, cupboard etc. The mount is customised to suit the ports and requisite access points of the switch box. the mount is…
A mounting plate for the TP Link TL-SG105 E network switch that allows you to attach it to a flat surface using double-sided tape. I recommend using PETG or another strong filament to keep the screw heads from breaking off. Print with…
Click to Read About 6.5 inch and Rack Frame 6.5 inch Rack Mount Collection It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on…
For the TP-Link TL-SG105E. Air vents not coverd, all ports/connector remain useable, all LEDs visible.
As mine broke a few month after printing, I decided to robustify it. Very good design from t0b1 Category: Electronics
This bracket is designed to mount a Netgear TL-SG105E 5-port network switch on a Multiboard grid using the versatile Multiconnect connector system by DavidD . Print the Model The clearances are optimized for a tight fit and work well with…
Underdesk mount for the TP-Link TL-SG105-M2 (2.5Gbit 5-port Switch). You can either print the (Bracket Top Left & Top Right) OR (Full Bracket & Magnetic Cable Holder). I have not tested the full bracket yet, will do so soon. Materials…
Remix of the 6" enclosure to mount a Netgear TLSG105 PE mount PoE switch. Printed in PLA, face down, without supports.
You need zipties for the power brick. The switch slides into the mounting brackets and locks itself in place. There is also a version for 10 inch racks:
Just an easy to print mount for the SG105 switch.
Simple remix rack mount for the TL-STG105 switch. You can print this face down orientation Should not need any supports I printed it with a 15% infill and 2 walls. I have 2 of these, so I printed left and right. But you can also print a…
A 7-inch Rack Mount for the TP-Link SG1005P | SG105(E) | OC200 series. This model is compatible with the GeekPi RackMate TT (Affiliated link). This model is part of a series of 7-inch rack mounts I've designed. You can check out the…
This is a 2 sided holder for TL-SG105 units, that makes them compatible with Wakoma Nimble racks
Printed in PLA, seems to be fine with the heat.
Needed a way to get a small 5-port network switch off of a shelf to make room. Decided to hang it underneath the shelf above. Designed this holder specifically for the TP-Link TL-SG105 switch and to hang from standard hardware-store wire…
My new TL-SG105 doesn't fit the original mount downloaded here. Vendor design changes perhaps? The original mount peg positions are 14.33mm too far from the tab border and are also too big to get through the “+” holes on the switch. What…
I designed this model so that I could mount my network switch to my wall for my homelab. The model was designed in TinkerCAD, and the design can be accessed here: https://www.tinkercad.com/things/6CWzo7I8oKr-tl-sg105-cradle
I needed to hang my tenda SG105 switch on a ikea-skadis-like pegboard so I took Juan's hook and attached it. Original thing: https://www.thingiverse.com/thing:3413856 I would print the hooks first and then either the horizontal or…
A wall mount for the TP-Link TL-SG105-M2 5 port 2.5Gb switch. Uses command strips. The keyhole mounts are 150mm apart, so this mount may fit other devices with this keyhole mount width. The keyhole pegs will work in either the vertical or…
Mount the TP-Link TL-SG105S switch on its power adapter to avoid/reduce under-desk clutter. The switch slides in from left side and locked in place by the cables. Notes : I designed this with the UK adapter (Type G) in mind, can't test it…
Mount for TP-link switch SG105 and PI4 on 5mm standoffs
SG105 & OC200 modular rack mount requires 1u rails https://www.printables.com/@LvL_Dani_470947/collections/2036642
I did this to mount a switch under a table. I recommend printing as shown in the picture (the .3mf file is exactly the same) to minimize the risk of layers peeling off from each other during screwing down.
Bracket for the Tenda SG105 to mount to the wall, or even under desk/table. remixed to fit the smaller switch, and to use #6 screws.
Homelab Mini Rack – Modded Edition This is a remix of the original mini rack case, modified to be more functional and give it a PC case aesthetic. Modifications: Honeycomb front grille with 40mm cable management extension – gives extra…
Description This is a custom DIN rail mount made for the Tenda SG105 network switch. The mount allows the switch to be installed neatly inside an electrical cabinet, control panel, server box or any other DIN rail based setup. It is…
SG105 mount with cable hooks to easily route the cables backwards for a cleaner mount. I used an infill modifier for the top side and hooks @ 100% for stronger hooks but it is not required. Turned out quite strong with the modifier.…
Simple TP-Link SG105 switch mounting solution. PLA will work fine as these do not get too warm under most conditions. PLA 15% Infill No Supports
Mount your TP-Link TL-SG105PE switch (or any other switch from the army of clones on the market with dimension 98 x 100 x 25 mm) on an Ikea Skadis board. Two M3x8 countersunk screws are needed to screw the bracket to the base plate. You…
Easily attach and secure Tenda SG105 to Multiboard (Multibuild) grid. horizontal / vertical version securing snaps for vertical version to avoid slide-off Vertical mounting: attach Tenda SG105 onto two pegs, slide it "to the end" snap-in…
Fixed the large gap in the original model
It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…
Click to Read About 6.5 inch and Rack Frame 6.5 inch Rack Mount Collection It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on…
I did this to mount a switch under a table. I recommend printing as shown in the picture (the .3mf file is exactly the same) to minimize the risk of layers peeling off from each other during screwing down.
A 7-inch Rack Mount for the TP-Link SG1005P | SG105(E) | OC200 series. This model is compatible with the GeekPi RackMate TT (Affiliated link). This model is part of a series of 7-inch rack mounts I've designed. You can check out the…
My new TL-SG105 doesn't fit the original mount downloaded here. Vendor design changes perhaps? The original mount peg positions are 14.33mm too far from the tab border and are also too big to get through the “+” holes on the switch. What…
Fits that specific model, but may be tweaked for other models as needed via the main files.
Simple TP-Link SG105 switch mounting solution. PLA will work fine as these do not get too warm under most conditions. PLA 15% Infill No Supports
Remix of DespairFlare's "TP-Link TL-SG105 Wall Mount - Renter Friendly" model for M2 version
Mount for TP-link switch SG105 and PI4 on 5mm standoffs
Homelab Mini Rack – Modded Edition This is a remix of the original mini rack case, modified to be more functional and give it a PC case aesthetic. Modifications: Honeycomb front grille with 40mm cable management extension – gives extra…
Easily attach and secure Tenda SG105 to Multiboard (Multibuild) grid. horizontal / vertical version securing snaps for vertical version to avoid slide-off Vertical mounting: attach Tenda SG105 onto two pegs, slide it "to the end" snap-in…
Mount for TP-Link TL-SG105 with cut outs for air vents. Under the mount are two channels for the dc supply cable. Mounting is done with 4mm sink head screws. Print with front facing down.
I have a small communication box where I need to fix the TP-LINK TL-SG105 unit. Most models I have found have floating parts or are too big, so I decided to have my own minimalist design
Bracket to hold a TP-Link TL-SG105 Network Switch on an IKEA Skadis pegboard using the built-in keyhole mounts.
Simple case for v4 of the TL-SG105. Prints without supports. PETG recommended for heat resistance. Features air vents and full access to DC power input and Kensington lock slot. Perfect for mounting the switch with Velcro or similar…
Fits that specific model, but may be tweaked for other models as needed via the main files.
Montage für lan switch für Nutschine TL-SG105
The power cable "ring" doesn't require supports, but the mounting plates does. I recommend using an interface material with a ironing function on the top surface of the supports to achieve a smooth surface (hints in the screenshot). For…
Remix of DespairFlare's "TP-Link TL-SG105 Wall Mount - Renter Friendly" model for M2 version
Minimal remix for the TP-Link switch. Fix M3 nuts into the place as on the photo, screw in the bolt to the exact height and attach the switch.
Little remix to mount a TL-SG105E in your 10" Rack. You have to remove the two little screws under the switch. After that you have to slide the switch in the mount until its flush with the front. The last step is adding two M3x6mm screws…
Took the model for TP-Link TL-SG105 Switch https://www.printables.com/model/66935-hanger-for-tl-sg105-network-switch and added pegboard pegs from https://www.printables.com/model/225209-pegboard-peg/files
This model has tight tolerances. I would recommend printing it from PETG due to the heat that might be produced from the switch.
Meine Empfehlung ist denn Halter mit 20% zu Drucken Wird mit 2 3mm Schrauben an eine Holz platte angeschraubt.
This support allows you to rack a 16 or 24 port switch and a 5 port TP-Link switch on 1U. Ideal if you want to complete your network installation with a small POE switch... Tested with on LEFT : TL-SG1016DE RIGHT : TL-SG105PE TL-SG1005P
Dual TP-SG105 Switch Mount for 10" Rack Takes forever to print but worth it, tolerances don't matter too much, just sand down sides a little if too tight.
Adapter to mount the TP-Link SG105 Network Switch to one of the TV Backside Vesa screws
