Liczymy pasujące modele…
This is the original version, the version that doesn't need pipes for hardware is here: What would be the Achilles Heel of a Sledgefire? The long reload cycle perhaps. And to remedy this, in designing this monstrosity I have sacrificed…
What would be the Achilles Heel of a Sledgefire? The long reload cycle perhaps. And to remedy this, in designing this monstrosity I have sacrificed everything: simplicity, optimal print orientations, even common sense. Still in terms of…
Clips for the Cryptid Sledgefire. Now with improved mega clips. Recommended print settings: 2 walls 15% infill no supports. You might need to clean up some of the cam-track overhangs with a hobby knife.
An alternate Wishbone part for the Cryptid that uses an M3 x 16mm socket head screw. If you have a set of M3 screws and don't want to buy a pack of M6 grub screws you only need one of. Hardware: M3 x 16mm Socket head screw. Just screw the…
silly sledge v30 i guess, spent half a week prototyping the ejection but didnt get it to work, everything else dimensioned correctly works well, have fun! feel free to remix this again to get it to eject properly if you would like to ask…
Printed with “Amazon Basics - 3D Printer TPU Plastic Filament, 1.75 mm, 1 kg Spool, Black” on a Bamboo Labs P1P with 25% infill. This is designed to fit two GensACE Bashing 3S1P 5000mAh (133mm x 25mm), which I found on Amazon. As you may…
The most significant updates include: return spring around barrel: compression spring 20mm OD, 1,5mm wire diameter, 305mm long- shortened to about 170mm. shortening the return spring in combination with the modified pump block allow for…
silly sledge v30 i guess, spent half a week prototyping the ejection but didnt get it to work, everything else dimensioned correctly works well, have fun! feel free to remix this again to get it to eject properly if you would like to ask…
Sledge's hammer from siege. Would probably work best with a fine nozzle to get the hammer nubs to print better. I used a 0.4mm nozzle and it turned out decently. Download 2 of the head parts and one each for the shaft.
This 4 part sledgehammer head was made as a prop for a youtube video. Printing: just print Assembly: Stick the pla2 part into the pla1 part. Then you can switch between the fakeplahead.stl part and the tpuhammer_tpu part. Video: (used at…
(EN) Sledge as decoration. Easy to assemble. (CZ) Sáňky jako dekorace. Složení je snadné.
Duplo sledge great for snow riding or as a helicopter landing skids. Note: Lego tolerances are very precise and your printer may not meet them. Maybe you will have to fine tune the model in your slicer (scale/flow/...). I added a file for…
A tool that helps when you want to prepare the skid of a (sports) sledge. I guess the pictures do answer most of the questions. I used M5 screws and thread insert. Printed in PLA. 15% infill. The original is done in FreeCad and I've put…
Handles designed to be fitted to a cheap plastic sledge to make for even more snow time fun. Requires a couple of 3mm dia. bolts and nuts to afix
I wanted to shoot silly shells from my SledgeFire. I had to do a lot of shell cutting, but it worked, kinda. Maybe with more springpower, but it shoots Mega and 3 shot shells well. You can throw a MegaXL farther by hand, though. I made a…
This is a pretty simple dummy T-Bar. It is not the correct length nor does it have any holes for mounting in the car. (Neither do I recommend installing it, as it would likely break and cause chassis bending) I simply made it to help make…
This is a nice mount to install a JR power connector into the Traxxas Sledge. I designed it so I could easily connect and disconnect my custom light kit. It slides firmly onto the T-bar and you can install a female JR connector into it…
I recently added a reversed GPM motor mount to my Sledge so I could run a Max6 combo. However, I couldn't find a good way to mount the ESC in the front of the car, so I grabbed a standard Hobbywing mounting plate and got to work in…
Here's the model that I made to act as a proxy for the Frosthaven summons, the Sledge Driver! The artwork for this guy is available online at…
I have three SledgeFires. The first two I cut up and modded, and the third i found in the thrift store with TWO ORIGINAL SHELLS. I want to keep this one stock… But that empty slot in the stock shell storage made me anxious. I tried the…
Made a single shot nerf shell and a MEGA shell for the SledgeFire using the “original” look of the stock shell. I would suggest NOT using the MEGA one if your SledgeFire still has the shell ejecting thingie in the barrel. It does get in…
I have updated the design, so the holder is sleeker without cutting down on ability hold heavy hammers. Sturdy hammer/sledgehammer holder for Multiboard is made to hold a 1.5 kg (3.3 pounds) hammer. (it will properly be able to hold a…
[Edit: Note that there seems to be a lot of variances unit to unit, so this shim will only work for some users.] The Qidi Plus 4 nozzle cleaning system leaves quite a bit to desired, but I hope I can alleviate some of the issues with this…
Edit: I added another spacer. This one is even harder to put in but yields better power. Spacer for your Sledgefire spring. From eye it seems to be about a 10 fps boost. You should be able to push it over the nub that holds the catch in…
It's hammer time. Simple, yet effective. It's a sledge hammer. Two-handed grip recommended. Two print profiles: 100% and 250%. In my test prints, printing it with the head on top printed a slightly cleaner version, but feel free to flip…
Couldn't leave the old version alone. First thing I did is make a groove to slot in the cut-off muzzle from the old barrel into the new barrel. now no gaping hole in the front! Looks smooth! NICE. I moved the breech a little closer to the…
Wanted my SledgeFire to look like a sawed off stock. Also using this a test model for a future SledgeFire stock idea.
SLEDGEHAMMER Dual Y axis drive. Ever wish you could get your old ender 3 to preform like newer machines without spending I a ton of money. my goal is to keep these ender clones out of the landfills and keep up with more modern machines…
If you used one of my conversion kits to make your SledgeFire shoot Silly Shells, you will need to replace the standard stock with this bad boy. Why? 3 shell storage! Conversion model (latest update):…
This is a “Pro” version of the previous stock ( https://www.printables.com/model/1336550-sillysledge-stock-with-ammo-storage ). It is a little more sturdy, and has more area for the epoxy to stick. If you used one of my conversion kits to…
Printed with “Amazon Basics - 3D Printer TPU Plastic Filament, 1.75 mm, 1 kg Spool, Black” on a Bamboo Labs P1P with 25% infill. This is designed to fit two GensACE Bashing 3S1P 5000mAh (133mm x 25mm), which I found on Amazon. As you may…
I recommend to use a heavy bey but any other type can be fine. The photo I took of the bit was built by a cut silicone nozzle that i glued to a bit that i soon made into a 3D model.
Modern Industrial Decor | 3D Printed Hammer | Polygon Art Object
Printed a bottlenose Silly Shell with an 8 inch barrel. I wondered if i could fit the barrel on a SledgeFire shell. So I tried. And here it is. It will only work with a SledgeFire with the ejector removed, so keep that in mind. (won't…
Meet the Christmas Sledge — a stylish 3D printed decoration with a clean modern look! 🛷 Length: 100 mm 🎄 Perfect for minimalist Christmas setups, table decorations, or as part of a modern festive scene ✨ Simple, elegant, and designed to…
The most significant updates include: return spring around barrel: compression spring 20mm OD, 1,5mm wire diameter, 305mm long- shortened to about 170mm. shortening the return spring in combination with the modified pump block allow for…
This is a highly accurate 1:1 replica , based on the real Six Invitational Trophy that's being handed out to world champions of Rainbow Six Siege . Other replicas, even the official ones, are based on the in-game model, which has totally…
If you like using the Mini Trio silly shell but also want to load it into your Silly Sledge, use this barrel! Untested, but it should work ok. If not, let me know.
Shell: Converts the Nerf Sledgefire to fire 1 half-length dart through a 17/32 brass barrel. Deactivates the air restrictors well enough without needing removal. The brass barrel must be epoxied into place inside the printed shell. I also…
hw required hw rn: m3 square nut x1 (5.3x5.3 thinner better) m3 hex nut x5 m3x16 x1 (for the lever hinge bit) m3x30 x3 (bottom lever hinge bit) m3x25 x2 (top catch bit) 016 oringx1 (breech seal) m3x20 x1 (sled ejector) 2-3mm elastic for…
It is a SillyShell holder and rear sight for the SillySledge, a SledgeFire that has been converted to shoot SillyShells. If you use the SillySledge Stock AND keep a shell in the barrel, that's 6 shells ready for use! There is a little…
A cool sledgehammer style eraser for your pencil and it is a better eraser than normal pencil erasers Its a tight fit so you don't need glue Its super fast and takes 6 min Print with supports on and use PLA The eraser is one of those…
Attribution of models in images Dummy 13 Version 1.0 by Soozafone is licensed under CC BY 4.0 Insects nature tube - Copyright © 2026, Wild Republic - All rights reserved Attribution This work, “Basic sledgehammer for Dummy 13” is an…
Attribution of models in images Dummy 13 Version 1.0 by Soozafone is licensed under CC BY 4.0 Insects nature tube - Copyright © 2026, Wild Republic - All rights reserved Attribution This work, “Basic sledgehammer for Dummy 13” is an…
Sledge's hammer from siege. Would probably work best with a fine nozzle to get the hammer nubs to print better. I used a 0.4mm nozzle and it turned out decently. Download 2 of the head parts and one each for the shaft.
thanks to soygama0404 for making the template i used for this bey
Use instead of original ejector at Nerf Sledgefire, to get out the shells automatically. Print Settings Printer: Elegoo Neptune 2 Rafts: No Supports: No Resolution: 0.2 Infill: 0% Filament: RedLine PLA, PETG Notes: Nozzle 0.4 Wall 0.6…
Load modded Nerf Sledgefire with ULTRA-Darts. Original Ejector needs to be cutted to a hight of at least 12,5mm. Print Settings Printer: Elegoo Neptune 2 Rafts: No Supports: No Resolution: 0.2 Infill: 30% Lightning Filament: RedLine PLA,…
This handle was done by me to pull my sledge. The hole for the rope is 10 mm. Print instructions Should be printed with high infill to make it as strong as possible.
This is the crossbar that holds the body posts on an ancient Traxxas Sledgehammer. I think it should be at its strongest when printed on its side, as is. I used ABS and it's holding together so far. Category: R/C Vehicles
When for outdoor use use PETG or equal due to temperature influences. two halves to be glued together. therefore no supports required
I designed this Thing as a replacement for a missing Sim-Card Holder in a new "B-Ware" Thinpad Tablet where the sledge was missing. I dont know how to call it correctly but i think its clear what it is. You may need to sand it a bit,…
Tool holder for mini sledgehammer. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 100mm W - 53,29mm H - 60mm We design all…
Tool holder for Sledgehammer 4.5kg/ 10lb. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 50.03mm W -91,228mm H - 62,5mm We…
Shells for the Nerf Sledgefire blaster that can take a beating. Regular triple shell for Elite darts, single Mega dart shell, shell for a 16mm PVC tube for single Elite darts and a blank shell for anyone that wants to create their own…
A Printable Sledge Hammer I printed this with a 1mm nozzle, .2mm layer heights with .6mm infill at 99%, total weight is 1.1 pounds. About 6.5 hours for the head and 5.5 for the handle vs. 40 hours just for the head at 4mm nozzle and .2mm…
The model is easy to print and easy to assemble. You will need: - the printed files - some glue - a piece of filament of the same color 1. Print the necessary models. 2. Glue the marked surfaces shown in the picture. Firstly fit the 2…
This has been tested extensively and works wonderfully. My first post, hope you enjoy it!
This is a replica of the Sledge hammer in real size. The original replica of the hammer (Scale 1:2 - 50cm) from Ubisoft can be found here:…
New file 2/7/19 that should address length and dart fit issues I had in earlier version. All versions work in mk18. This is a remixed version of slug's shell modified for printing. It should replace stock shells. I made one and it worked,…
My daughter find some lack of her Barbie's winter equipment ;) So I measured Barbie's body and prepare this sledge model. Very simple construction and easy to print but playful item :) Print your own! Print instructions Printer Brand:…
I made some size adjustments. I pulled in the bottom and widened the top, which allows for effective launching of Dart
Ergonomics design, with special holes for your rope / wire
Ich habe nach einer Möglichkeit für eine spielfreie Befestigung eines Schiebeschlittens an einer Mafell Erika 85 gesucht und diese Gleiter konstruiert. Die Gleiter sind optimalerweise 100mm lang und werden mit 95% Infill gedruckt.
Stamp to aid with cutting 1/16 Inch (.0625”) thick adhesive backed foam. Improves seal as required for many Sledgefire upgrades! Print as imported, no supports required. Place stamp on a piece of 1/16 Inch (.0625”) thick adhesive backed…
These magnetic sledge holders use a 20x5mm round magnet to hold your tool in place. The magnet can be inserted (and possibly glued) from behind. A single Neodym magnet holds a 500g sledge even horizontally in place (see pictures)!…
These magnetic sledge holders use a 20x5mm round magnet to hold your tool in place. The magnet can be inserted (and possibly glued) from behind. A single Neodym magnet holds a 500g sledge even horizontally in place (see pictures)!…
Place the part upside down so that the threads and sealing surface are even. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Yes Supports: Yes Resolution: 0.15 Infill: 95 Filament: U3Print TPU 60D Black Notes: Bed temp = 70…
Model of a classic wooden sled. You can use it as a gift for children or as a Christmas decoration. Kit card also included. The joints are tight and solid. Assembled model size approx: 13 x 5 x 4 cm Print settings: No special settings are…
Printed at 30% infill witch seams to give it similar squish to stock
Design is intended to be printed upside down. Pieces slide together to wrap around steel tubing of roll bar. Fit is very snug and glue is not required. So far this has held up well to bumpy drives around the pasture without issue. I'm…
The sled can be assembled without using glue. Sáně je možné složit bez použití lepidla.
Some sledge accesories I made for my son when he was young (2 years old) so he had something better to hold on to and a back rest to sit up right. He still loves and uses it today after 2 years. There are no external tools required, the…
This 4 part sledgehammer head was made as a prop for a youtube video. Printing: just print Assembly: Stick the pla2 part into the pla1 part. Then you can switch between the fakeplahead.stl part and the tpuhammer_tpu part. Video: (used at…
Sliding locking openings and internal ramps so nothing gets stuck. I really love this weapon's design, so it seemed fitting to make a dice tower/box out of it. Nice clicking movement and interlocking panels make it feel neat to use! I…
Inspired by some other pen caps, i decided i wanted something truly impractical. Really helps you not lose your pen cap though! All parts are printed flat, and it needs a little superglue.
So I had an old Sledgefire lying around that was toping out at a bout 1m range for one dart and the others flew out only when the stars aligned correctly. so i designed a barrel and leaver to transform it into an very strong single shot…
This is a remix of xcnerd88's sledgefire shell. The barrels have been adjusted for a tighter dart fit, and the shell is tapered at the front for easier insertion. I have also added bars at the back to prevent pushing the darts too far…
I've made a spacer for the SVS PC-13 amplifier upgrade. It has been test fit with the original Bash amplifier and the Sledge 1200D in my 13 Ultra. The height is 10mm but it can be scaled to fit your specific subwoofer needs. Be sure to…
![Nerf Sledgefire powerdart mod [NO HARDWARE NEEDED]](https://media.printables.com/media/prints/894945/images/6847490_bbc94f38-c88f-489f-859f-7e59c8f183c2_066ac319-792a-459c-9886-44572a479ea5/1716921545944.jpg)
