Liczymy pasujące modele…
Not fully tested! Time will determine how well this model holds up. Model has spaces included for a battery and solar charger but I ended up not using these. Model was originally designed to use the sparkfun micromod weather carrier…
This is an enclosure (bottom, top, feet) for the Sparkfun's Openscale and also a plate for the load cell. It should work with the strain gauge load cells from uXcell, Sparkfun, and Adafruit; 80mm x 12.7mm x 12.7mm (note that Adafruit's…
Mounting holes available for Arduino Uno and XRP Controller. (Refer to images) Servo gap fits 9g (blue) servo motor Mount batteries with double sided tape below the frame at the back. LiPo batteries also fit if using stepper motors.…
This is a case for the Qwiic Ultrasound Sensor https://www.sparkfun.com/products/17777 that can be mounted from behind. It also works with the identical (apart from colour) Zio Ultrasound Distance Detector…
The original XRP chassis is cool, but not that well optimized for printing. It requires substantial supports and uses lots of fillets tangent to the print bed, which causes very steep overhangs that print poorly. To improve the…
OpenSCAD file for the SparkFun GPS-RTK-SMA Source file based on YAPP_Box Demo RealBox - transmitter/receiver v3.0 Note: Requires the YAPP_Box OpenSCAD library SKU: GPS-16481 Product link:…
Little Case for the SparkFun Soil Moisture Sensor ( https://www.sparkfun.com/products/13322 ) upper electronics section. Requires: 2x M3x8
Also check out the Case for the SimpleRTK2B
This is a window or wall mount for the RAK and Sparkfun LoRa antennas, tested with the 90cm long 5.8dbi antennas that can be found here: https://www.sparkfun.com/products/15597…
This enclosure requires no additional hardware. If you print from gcode / 3MF file, there is filament change command added to swap colors. You can print in two or three colors. This works even if you don't own the MMU! You will just have…
Because of the addition of extra solder pads, theRedBoard Artemis does not fit into the old arduino footprint. This bumper uses the correct dimensions. Print instructions Category: Electronics
Got these Sparkfun knockoff usbc breakout boards, and wanted to put them in various projects. Made this crude 3d model to help develop enclosures for the part. part: https://amzn.to/3XQvXwo
You will need to print a retaining tabs, which can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab An Din Rail mount for up to four Sparkfun Qwiic modules using M3…
Simple mount for Sparkfun's Blackboard C and RedBoard Plus. Needed something similar to what is commonly available for Arduino Uno. Two versions available; one with ears for mounting and a second one without. Printed in Atomic PLA with…
Description: This is a 6-legged full walker bot mod for the Sparkfun XRP, models included are the STLs for the modded body and legs. Components: Necessary parts include an Arduino Uno r3 or other similar board, a servo controller board…
An 8020 mount for Sparkfun Qwiic modules using M3 screws. This is for a more permanent usage. This design can mount two of the two hole variety with two of the four hole models or up to four of the four hole modules. The double set of…
A din rail mount for SparkFun's quad solid state relay board. You will need to get the tab from: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab to use this part. This bracket…
This sensor mount is designed to connect most Sparkfun Qwiic enbaled sensors/breakout boards to the Experiential Robotics Platform (XRP) Kit by clipping on the sides and connecting to an open Qwiic port. The model is designed to be 3d…
A din rail mount for a Sparkfun quad relay board. You will need to print two tabs for this design. They can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab…
Made with a slot for an additional sticker or print with a logo (⌀25mm) The size of the inserted magnets is 20 * 10 * 3 mm and they can be found in amazon es . The battery used had a capacity of 1200 mAh and 5 mm height. The Datalogger…
As much as I like seeing a PCB populated with components, I really don't like handling them directly when they're powered up. No matter what the voltage. So I decided I would make a case for the Sparkfun AVR Programmer . I'm sure there…
This is a nice little enclosure that I designed for the Sparkfun Decade Resistance Kit 13006. It includes printed knobs and a faceplate so that only the selected resistance digits are displayed. I have included the Fusion 360 file if you…
SparkFun USB-C Breakout Board adapter for ROCCAT Vulcan keyboards. Pictures should explain most, if not there is a Reddit thread showing the build with more pictures. Reddit Thread for build.…
The SparkFun Flame! Sign up to become a SparkFun Affiliate!
I wanted a clip to attach my Sparkfun Redboard to my protoboard. I've printed en PETG so it won't break when I slide it on the side of the board. Sparkfun Redboard: https://www.sparkfun.com/products/13975 Print Settings Printer Brand:…
This is a scale, printable model of the SparkFun Humidity and Temperature Sensor Breakout board for the Si7021, which has an I2C interface and costs around $10.95. The product page for this device can be found here . I managed to print…
XRP Sensor/Display Tower Originally designed to mount Sparkfun Qwiic 1.3" OLED and the ENS160 Environmental Sensor, this mounting tower, can be adapted to any standard sized Sparkfun Qwiic sensor and/or display. The mounting tower snaps…
An 8020 based mount for six Sparkfun alphanumeric displays. For example: https://www.sparkfun.com/products/16426 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker…
This mounting plate for SparkFun XRP robotics kit allows users to connect a wide variety of expansions, sensors, modules, motors, etc. Expansions can be easily connected using standard 4mm screws. The board is easily connected to the…
The SparkFun Robotics Claw MkII (part # ROB-11524) is a big improvement on their mark 1 model. The new Pan/Tilt MKII bracket (part # ROB-11674) is also nice (if a tad pricey). Unfortunately the instructions to mount a claw to the Pan/Tilt…
A holder for two spark-x alphanumeric displays, two buttons and a sparkfun Artemis redboard. I really like the Sparkfun qwiic system. On the really nice things that sparkfun does is to allow consumers to purchase products that they have…
A Sparkfun Pro Micro RP2040 Tray that I used to hold the controller in place within my Redox hand wire case. the little drop down ledge is so the wires can reach over inside a low clearance case. STP file included in case you want to…
An 8020 mount for Sparkfun Qwiic modules using pegs. This is for temporary setup and testing. Use a drop of hot glue over the pegs to make a more durable project. This design can mount two of the two hole variety with two of the four hole…
A 8020 series 10 mound for two sparkfun spark-x alpha displays with two 16mm button holes. For example https://www.sparkfun.com/products/16425 (they do have other colors.) https://www.sparkfun.com/products/11968 (same) Print instructions…
This is a remix of Rúben Oliveira 's case, with the battery sleeve sized for a 2Ah battery. Added a snap/glue on battery door. Parts: Battery - https://www.sparkfun.com/products/13855 OpenLog - https://www.sparkfun.com/products/16832
Box designed for outdoor assembly of sparkfun qwiik KIT-15209 rfid reader. Printed and assembled. I have tried to design this so water that enters the box should not reach the circuit board. Cable is to be pulled thru wall from inside of…
There's some great documentation on how to use an accelerometer with a Prusa MK4 to measure the parameters needed for tuning input shaping here: https://github.com/MCDELTAT/MK4_Accelerometer I'm using a Sparkfun LIS3DH breakout board for…
I have used PETG filament. -0.15 layer height. -20% infill. Part of E-textile project: Learning Platform for E-textiles
This is a 2 piece case for the SparkFun MicroMod Input and Display Carrier Board . The case was printed with PLA. The joystick and button operators are a bit small and were printed on resin printer. The two halves of the case sandwich the…
A very basic model of this part from SparkFun: https://www.sparkfun.com/products/16398 Missing a lot of things on the real thing but it can get you quite far in prototyping case design as is Used in my Air Quality Monitor project (posting…
Bus pirate enclosure - printed PETG and gives a window to status LED's / cable connector and usb connection. Category: Electronics
This harness was developed to reduce failures in the Micromod Teensy board due to the offset set screw causing stress on the board. This harness has a latch at the center which will hold the board in place without skew. It will click into…
Enclosure for the small stereo amp kit sold by Sparkfun ( https://www.sparkfun.com/products/9612 ). This enclosure also includes space and cutouts for an external power switch, RCA audio-in jacks, a power jack and a 4 spring speaker…
LoRa / Meshtastic Antennenhalter für die Fensterbank – ohne Bohren, spurlos No-Drill Windowsill Mount for a LoRa / Meshtastic Antenna 🇩🇪 Deutsch Warum es das gibt Ich wollte eine LoRa-Antenne draußen vor dem Fenster aufstellen – mit…
This is an enclosure for the Sparkfun's RFID USB Reader (SEN-09963).
These are mounts to fit the 32x32 RGB LED matrix panel from Sparkfun( https://www.sparkfun.com/products/14646 ) into the 10x10 shadowbox from Michaels( https://www.michaels.com/black-extra-deep-shadowbox-10x10-studio-decor/10229048.html )…
I built this for the vinyl-cataloguing station: the half of the collection that never made it into Discogs needed a scanner that didn't involve holding a phone over a sleeve and waiting. This is a wand: lens out the front, a 45 mm hollow…
Sew-able enclosure for https://www.sparkfun.com/products/102 . Used as a main power switch. The switch itself is embedded below the surface of the enclosure by a small amount, so the switch is difficult to slide without a tool of some…
Enclosure for custom ESPHome device for Mitsubishi Heat Pump Control using the CN105 port and this project: https://github.com/echavet/MitsubishiCN105ESPHome Specifically, see breadboard layout and components in this post:…
Get the sensor from Sparkfun https://www.sparkfun.com/sparkfun-qwiic-mini-tof-imager-vl53l5cx.html Original model here https://codeberg.org/uwearzt/freecad/src/branch/main/lab/gridfinity/vl53l5cx.FCStd
A small box for the Sparkfun FT232R breakout board, useful when you need just the Tx and Rx lines. Printed in transparent PETG, so the lights are still visible. Make sure your board fits, as the box is quite tight. The OpenSCAD source…
This is a simple case for the SparkFun Teensy Arduino Shield Adapter. I was designing a capture-the-flag style hardware hacking game for use with the Bus Pirate 5 and wanted a processor with more capabilities than the standard Arduino Uno…
A custom enclosure designed for SparkFun’s standard WiFi IR Blaster board. The case allows easy access to the GPIO pins from the bottom, and after removing the top cover (secured with screws), you can conveniently switch the board into…
I use a standard velcro for quickly close/open (take out microSD and change battery)
Mount for https://www.sparkfun.com/sparkfun-grid-eye-infrared-array-breakout-amg8833-qwiic.html. See https://codeberg.org/uwearzt/freecad/src/branch/main/lab/gridfinity/grideye.FCStd for the original model
LEGO devices which use the Powered Up connector are actually quite easy to hack into! To demonstrate this, we built a robot using hardware from the LEGO SPIKE platform and various off-the-shelf hobby electronics, MicroPython, and 3D…
Test the BMV080 from Sparkfun on Gridfinity with a breadboard.
Official Project Page & Documentation: https://www.qzss4survey.com/jps/jusinki/osm-gnss 1. Project Mission / プロジェクトの理念 [English] High-precision RTK-GNSS surveying equipment has traditionally been too expensive and complex for many field…
Mount for https://www.sparkfun.com/sparkfun-grid-eye-infrared-array-breakout-amg8833-qwiic.html. See https://codeberg.org/uwearzt/freecad/src/branch/main/lab/gridfinity/grideye.FCStd for the original model
Get the sensor from Sparkfun https://www.sparkfun.com/sparkfun-qwiic-mini-tof-imager-vl53l5cx.html Original model here https://codeberg.org/uwearzt/freecad/src/branch/main/lab/gridfinity/vl53l5cx.FCStd
Basic enclosure for the Sparkfun ESP32 Thing with a USA style outlet plug extension for a side mounted wall plug. Wave cut out in 3MF file as negative volume for venting. Also made a side mount for the cover. Prints in any material.
This plate allows thing plus and qwiic modules to be secured with 3mm hardware (or smaller with brass inserts). It is then easy to wire things up using qwiic cables. Designed for use at project camps. PLA or PETG works fine. 0.15 or…
A stand for a Sparkfun 20x4 SerLCD There are two files, one with a mount for a Raspberry Pi Zero 2 and one without the mount. M2.5 standoffs needed to mount the LCD (and the Raspberry) as well as some rubber feet.
Enclosure for SparkFun 20x4 SerLCD Enclosure - https://www.sparkfun.com/products/16398 Super easy to print. No supports needed, rotate so the top piece is face down on the build plate. The case closes with a nice friction fit but I still…
A Sparkfun QWIIC Adapter in step format to use in your own designs.
I created this case for my Buspirate board from Sparkfun as the existing cases where far too small.
Description This is a small, no-nonsense case for the SparkFun Basic Flashlight PCB. Designed to be compact, sturdy, and easy to assemble, with a printed button that directly actuates the onboard switch. Tolerances are intentionally snug…
I recently built a GPS-disciplined Stratum 1 NTP/PTP time server using a GPS module from SparkFun , which is connected via the GPIO header, and I wanted a way to mount it to my Raspberry Pi. I decided to make a HAT-shaped mounting plate.…
The din mount is adapted from Voron 2.4 - https://github.com/VoronDesign/Voron-2/blob/Voron2.4/STLs/VORON2.4/Electronics_Compartment/DIN_Brackets/pcb_din_clip_x3.stl - GPLv3
Designed as an easy mount for Sparkfun's with Human Presence and Motion Sensor - STHS34PF80 (Qwiic) device. Should also work with other breakouts in this form-factor, as well as half-sized boards, for example: Mini Human Presence and…
Mount for Sparkfun RedBoard (compatible with Arduino) with all connectors accessible. RedBoard has a slightly bigger footprint than Arduino R3, so mounts for R3 often do not fit. Because mount is wider, Arduino R3 fits fine as well. All…
This case securely holds and protects a Sparkfun Tinker Kit. It could be repurposed for other hardware, the locating pins that hold the main board will hold anything with an Arduino form factor. The model I've uploaded has no graphics so…
This is a mount for the Sparkfun MP3 Trigger Board. Category: Robotics
The initial release of this model is the first feature comp[le version of the casing. I will hopefully update this soon with full build instructions. NOTE: the switch used in this is smaller than the ones recommended on the SlimeVR…
A small case for the SparkFun Joystick Shield with the idea of an independent controller.
This thing contains a mounting plate and a drilling guide for the "SparkFun RFID USB Reader" (SEN-09963). The base plate is one mm thick. M2 5 mm or 1/4" 4-40 screws are needed to fasten the board to the mounting plate. The mounting holes…
A holder for spark-x alphanumeric displays. I really like the Sparkfun qwiic system. On the really nice things that sparkfun does is to allow consumers to purchase products that they have not yet brought to market under there Spark-X…
I really like Sparkfuns qwiic system but I always end up with a chain of modules scattered around the desk. This is my attempt at keeping some order in my life. This design mounts Qwiic modules using M3 screws. This is for a more…
Sparkfun (PID 14451) Motor Driver - Dual TB6612FNG (1A)
An mount for Sparkfun Qwiic modules using pegs. This is for temporary setup and testing. Use a drop of hot glue over the pegs to make a more durable project. This design can mount two of the two hole variety with two of the four hole…
A mount for SparkFun's quad relay board. https://www.sparkfun.com/products/16566 You will need to print two tabs for this design, which can be found here: https://www.thingiverse.com/thing:3401942
Case for the Sparkfun Bus Pirate by Dangerous Prototypes Print instructions Category: Electronics Summary Case for the Sparkfun Bus Pirate by Dangerous Prototypes
Mount for Big easy driver from Sparkfun. Double stick tape works grate on back. Category: 3D Printing
A qwiic stick that will support some of the sparkfun wider modules. You will need to print one retaining tabs, which can be found at: https://www.thingiverse.com/thing:3401942 or…
Just some models of SparkFun's Qwiic breakout boards and a retaining tab for mounting them on/in project. Enjoy! Includes blend and stl files of: standard board with 4 mounting holes standard board with 2 mounting holes Qwiic adapter…
Quick enclosure I made for the SparkFun Thing Plus - ESP32 WROOM (Micro-B) to get if off my desk
