Liczymy pasujące modele…
The stock bed‑leveling knobs on the Snapmaker U1 can be stiff and difficult to turn during manual leveling. To make the process smoother and more comfortable, I designed a simple grip‑enhancing tool that fits over the existing knobs and…
To make thumbscrew for 1/4 hex head. Just glue cap and screw will be captive.
The original outer diameter of the Thumb/Knob/Cap for 5/16" Socket Head Screw model by @BGeorgeFr was to wide to fit the Starlink pole mount, so I shrunk it to a diameter of 15 mm. Otherwise, the dimensions are the same. (M6 is close…
Print with 1mm layer height ideally so that the threads are clean
Simple M3 thumbscrew for battery enclosure. I used this M3x20 screw. https://www.mcmaster.com/91502A109/ Should print in place. The SLT file has the correct orientation. If you would like to change it up in Fusion I have attached the…
The fit can be rather snug so either press it hard with a clamp or drill it with a 6 mm drillbit. I made one a bit loose so one drop of CA glue fixed that.
Designed for my Airplane Phone Mount , these screw adapters are strong and hold the nut and screws very tight. I can't guarantee that these will work for every screw and nut combination. Personally, I used this kit from Amazon . Press-fit…
It was the weekend, and I didn't have the right screw on hand. In the spirit of "if it works, it's not stupid," I decided to design a Thumb Screw Knob in Fusion 360 for a carriage bolt (German: Schloßschraube DIN 603). The design was…
These are just pretty basic knobs for many types of nuts. I would suggest you print both the loose and tight version, so you can figure out what fits your needs. My print settings: * 0.4 mm nozzle * 0.2 mm layer height * 3 walls * 15%…
Taller narrow section, allowing the deeper screw to seat closer to bottom face so the spring is not compressed unnecessary. Made it because the original did not work for me.
This adapter should turn your ¼-20 socket-head cap screws into thumbscrews. This is especially useful for quickly screwing and unscrewing things from an optical table. I've optimized the model for fast printing without supports using the…
These brackets feature some enhancements over other designs: X-Airs are held in place by clips. No adhesive or tape. Feet added to the bottom of the brackets supports the goggles and prevents the focus adjust wheels from touching. Curved…
Simple thumbscrew for M4 nyloc nut. Prints without supports.
MK4 nozzle thumbscrews have been known to loosen on their own. My printer has experienced this phenomenon. This design hopes to lock them in place so that can’t happen. Before you install, have a look at your fan wire routing to ensure…
GoPro M5 thumbscrew with a better grip for a tighter connection. Insert (pressfit) a hex head M5x30mm machine screw.
The clasp and thumbscrew for our iPad tripod mount got lost. Since it's a rather high quality aluminum tripod, rather than buy a new one, I designed this in Fusion 3D and printed it on my MK4S in 0.15 Structural mode with surface ironing…
34 Different thumbscrews / bolt knobs for 17 different fasteners. Refer to the following table for sizing. Spacer height refers to the distance between the bottom of the fastener and the bottom of the knob. Can't find what you need? You…
3D-Printable Thumbscrew Knob – Easy Grip, Tool-Free Adjustment The 3D-Printable Thumbscrew Knob is a practical and ergonomic solution for quick, tool-free fastening and adjustments. Designed to fit standard M5, M6, and M8 bolts , this…
I 3d printed a panel to put inside bike bag to firm the mount when it is screwed to bike frame. The main problem is needing tools and messing around with lining everything up. Some bike manufacturers include thumb screws so I made this…
Modified to add a bolt through the top section - will fit a M6 X 150mm bolt - with thumbscrews - to disassemble.
Knurled round cover for the thumbscrews that come with chinese stealth bomber ebike frames. I ended up putting some double sided tape between the screws and caps to ensure they stayed on as I printed mine in PLA.
ISO 4014 & ISO 4017 hexagon head screws with encased thumbscrew head. M3, M4 & M5 are available up to 50mm in length. Updates: 2025-09-06: Filament change note added for Prusa Slicer Printing Print without supports. You need to setup a…
Left an incomplete build out and misplaced the glass thumb screws. Made these adapters to fit over mainboard screws(m3*5*7). Insert screw into adapter (I would suggest holding the adapter with pliers) and thread the screw into the…
Simple Screw Cover for Thumbscrews. Mainly designed for my (girlfriends) bequite case. Screws have high tolerances, you might have to scale a bit to fit every screw depending on filament settings etc.
This is just a basic 10 mm tall, 15 mm diameter grippy thumbscrew knob designed for M3 knurled inserts. These will work without the inserts but may not be very durable. Great for many projects. This knob was originally designed for 3D…
This is just a basic 10 mm tall, 15 mm diameter grippy thumbscrew knob designed for M3 nuts. Great for many projects. This knob was originally designed for 3D printers using M3 machine screws. I matched the hardware from this assortment…
Press-on thumbscrew head for 1/4-20 UNC bolts. Printing instructions: 0.16 mm layer height no supports infill 40% gyroid infill 2 perimeters
I created this replacement thumbscrew for the Park Tool PCS 9.3. The thumbscrew to secure the folding legs of the PCS-9.3 is lousy, The threading loose in normal usage. All you need is an M6 35mm hex head bolt and flange nut. The filler…
My first upload, please be gentle. This is my version of the GoPro thumbscrew tool. We all know that it can be difficult to tighten and loosen the thumbscrew on the GoPro finger mount (two and three prong ones). This tool fits inside the…
Needed a smaller SMA thumbscrew to fit for my diversity Module (Realacc or Furious FPV) Its meant to be a bit tight on the SMA nut (pressed it on with a vice) Prints Fine without support Print Settings Rafts: No Supports: No Resolution:…
Do you have 4mm screws and bolts that you need to adjust somewhat frequently but don't want to carry around an hex key with you? This is the make for you! This super simple design can be printed in mere minutes and can be screwed onto any…
An air filter using a 12032 fan and a commonly-available HEPA filter for your printer.
This is a thumbscrew cap for a hose clamp's hexagonal screw head. Regular hose clamps (tightened with a wrench) can be bought just about anywhere and in any size, but I can only get thumbscrew ones online, only in some diameters, and I…
A small tightening lever to apply slightly higher torque when fixing a DJI Osmo action to the standard GoPro mount. Disclaimer: Use at your own risk, more often than not there is no need to apply extra torque when attaching your camera.…
I always have trouble assessing how far I have already turned the thumbscrew on the Bondtech Extruder. This small cap shows this quite clearly and you can better estimate quarter, half and full turns ;-) Version 2.0 (2024-06-14): V2 has…
Little knob for making a thumbscrew out of a 3mm button head screw and square nut. Secure with thread locker. PETG with organic support, 100% concentric infill.
Thumbscrew Replacement for Tenere 700 Adjustable Windscreen A direct replacement thumbscrew designed for my specific adjustable Ténéré 700 windscreen. Lost one of the original screws on the road and needed a new one. Type: Compatible with…
I didn't want to have to have tools in order to swap out the battery on my MPP, so I modified the stockplate (which is also the battery door) to allow the use of thumbscrews. I used these thumbscrews . I also included a version with just…
If you need to assemble and disassemble in the field without too many tools thumbscrews come in very handy. I made parametric thumbscrew heads for M8 screws with hexagonal head. For rescaled print settings the model should fit for other…
Fully parametric model. You can set: the nominal screw size (M4-M20) the clearance the chamfer for the screw-head cavity the overall diameter the overall height the fillet for the edges
Modified tension arm to be a bit longer with a slot for the thumbscrew.
Monitor Shelf | No Gap + Thumbscrew Tightening The other designs available on printables are very nice, but none of them quite met my requirements so I made my own. I wanted it to be easy to print, be easy to put together + adjust the…
This is a knob that accepts a 1/4"-20 nut or bolt. I downloaded this from Thingiverse years ago, and wanted to share it with a friend, but could no longer find it here. I am not sure if it was deleted, or if it's just lost to the rather…
These are basic 10mm tall, 15mm diameter grippy thumbscrew knobs designed for M3 nuts. I added a chamfer/radius to the original model so you can use it in tighter spaces like the example shown. Printed in Elegoo PLA Matte, 4 wall loops, 4…
The stock bed‑leveling knobs on the Snapmaker U1 can be stiff and difficult to turn during manual leveling. To make the process smoother and more comfortable, I designed a simple grip‑enhancing tool that fits over the existing knobs and…
I needed a thumbscrew for two flathead screws to fix a 3D printed scissor adapter. I used freecad to make one out of two involute gears. Its a simple and fast method and it also allows to quickly change sizes using the included freecad…
To make thumbscrew for 1/4 hex head. Just glue cap and screw will be captive.
Inverted and made it more shallow. To use as thumbscrews on the Goodman Zone camera, for fastening the film back and ground glass frame. Print instructions Category: 3D Printing Print Settings Rafts: Doesn't Matter Supports: Doesn't…
Replaces the feedneck adjustment screw with a tumbscrew. The screw head should fit tightly and may need to be pressed in. Uses a SHCS #8-32x1" screw. I used a Hillman that I got from Ace Hardware.
The original outer diameter of the Thumb/Knob/Cap for 5/16" Socket Head Screw model by @BGeorgeFr was to wide to fit the Starlink pole mount, so I shrunk it to a diameter of 15 mm. Otherwise, the dimensions are the same. (M6 is close…
A simple and strong knob for M8 nuts with five spokes. Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: ≥20% Filament: Any Notes: Infill does not matter so much. Insert the M8 nut A M8 nut has to be pressed into the part…
Head: 3mm height, 14mm OD + .6mm diamond knurling on the outside, flat top. Shank: 3mm smooth length, 10mm threaded length. See SCAD I generated with Claude Code, it requires BOSL2. Allows for adjusting dimensions very easily. Printed…
A clip-on desk-edge cable clamp that routes one cable through a C-shaped hook on the side. No metal parts, no tools — the whole thing is three printed pieces. Prints: cable_holder_body.stl — the C-frame with the threaded hole and side…
Print with 1mm layer height ideally so that the threads are clean
This part fits into the top of a standard M4 hex screw, converting it to a thumbscrew - great for assemblies that need to be constantly adjusted. This was originally designed for use on a Folgertech 2020 Prusia i3, for the L bracket…
Lepus Blaster MK2 Battery Base Remix This is a remix of the Lepus Blaster MK2 battery base designed to improve both mounting durability and battery fitment. Changes Added a captive hex nut for use with a 6-32 thumbscrew Provides a…
simple thumbscrew attachment that can be placed over a DIN m8 hex bolt or nut. I designed it for my Bosch PBD 40 drill press but it is of course, suitable for a wide range of use cases. Category: Parts
Adapter for standard 1/4 inch camera screw improving ergonomics. You can modify the .step file for other sizes. Use as inspiration, print at your own risk. In case of questions feel free to reach out.
Adds about 14mm of space to the already ginormous Protean Battery stock. You will need a m3x25 screw.
Low Profile thumb screw can be used for a GoPro camera mount, or use the same screw on a Keihin Carburetor for the idle adjustment. Brass screws are better for the carburetor, the screw thread is M5. Can be printed small side down without…
My tripod came without a thumbscrew to fasten the handle to the pan/tilt head, so I modeled this part to work with an M6-1.0x30mm screw that fits the tripod threads.
Inverted and made it more shallow. To use as thumbscrews on the Goodman Zone camera, for fastening the film back and ground glass frame. Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 Infill: solid?…
My MMU is in a pretty tight location and I can't easily get an allen key in there to adjust the idler tension. Here is a design for some thumbscrews that can be pushed onto 40mm M3 screws to adjust the tension without an allen key. They…
My cheap lawnmower was missing a thumbscrew right out of the box, and rather than go back to the store I just made my own. Maybe I'll replace the other so they match :) I printed with 4 perimeters and 100% infill below and around the nut…
Often I found myself needing thumbscrews on my projects, and since M3-M8 are my most common used sizes i deceided to make myself some: The thumbscrews are designed for socket head screws and use a nut in the compartment on the underside…
Update may 24th: Elothan also added thumbscrews with support layers to the files so you can also download them there ! A quick remix of the nice thumbscrews from Elothan. These thumbscrews were hard to print nicely without supports. These…
The grip on these wraps around the top and bottom and works really well. Also included is a spring spacer to keep the springs from bending side to side. I used a small washer between the thumbscrew and the lower bed to keep it moving…
I need about 40 M3 x 8mm thumbscrews as pictured in the comparison photo. However, they're a little pricey and take a month or so to ship from China to USA. So, I got out the 0.25mm nozzle and FreeCad and put something together to adapt a…
Simple 1/4-20 x 3/4" inch thumbscrew I needed for a project. These work well with my Imperial Stair Gauge. Head has knurled edge for grip. Threads tested clean in a standard 1/4-20 nut after printing. No post-processing required. Print…
Introducing the POP 7" touchscreen kiosk! Create a CLIO interactive exhibit , an OctoPrint 3D-printer control panel, a Plexamp music streaming station, wrangle your web applications with Organizr , or just about anything you can imagine.…
I created this cap to use a M8 socket head capscrew as a thumbscrew with the V-block and clamp by i606. I have plenty of M8 SHCS laying around so this seemed like a good way to put a couple of them to use.…
This is a simple Thumbscrew for M6 hex head bolts or nuts. Use a drop of superglue to fix the bolt head or nut into the hole. I printed my in PETG but PLA would also be fine. I used 0.15mm layer height.
The original thumbscrews are great when you are in a position to use your fingers to tighten the screws, but I needed some knobs that are more convenient to tighten with your whole hand, hence these suit me better. Uses the same fantastic…
thumbscrew for easy and quick assembly of your fpv equipment Category: R/C Vehicles
I liked the knurling on the original design so I modified it for use with my M3 screws.
Remix with the hole for an M4 hexagon nut and placed in the right print orientation. I suggest printing it with 100 % infill for good strength. Feel free to like, download and follow. If you want check my other models. Happy Modeling and…
Often I found myself needing thumbscrews on my projects, and since M3-M8 are my most common used sizes i deceided to make myself some, and this is my Knurled version of my standard thumbscrews. The thumbscrews are designed for socket head…
knurled thumbscrew for M4, M5, M6, M8, M10, M12 print 0.20 or finer for the threads to work
This is a remix of the MMU2 thumbscrews for the MMU2 S . The longer thumbscrew should avoid accidentially pushing buttons on the MMU2S. If you already printed the short/original, you just have to replace the left thumbscrew, because there…
I was inspired by Elothan's https://www.printables.com/model/272115-knurled-m3-m8-thumbscrews but I wanted some which would look right on my Star Wars themed Voron V0.1. These are all meant to be printed with the hex side down and require…
Needed some way to hold a calibration microphone and had an old velbon 370CX(?) stand lying around, so I designed this thing to help me calibrate my speakers without having to buy a dedicated microphone mount. I'd imagine the size is…
The Svbony Dovetail Clamp is a top quality accessory for telescopes, but sometimes it is difficult to reliably fasten heavier loads. This thumbscrew handle gives you a better grip. The loose version is easily removable, and the tight…
If you have problems loading filament it can help to unscrew the tube and guide the filament manually into the extruder (make sure to straighten the last bit of filament) This screw makes it easier to do that for every filament change…
This turns any M3 bolt/screw into a thumbscrew. Print instructions I printed using the Prusament PLA .05mm ULTRADETAIL QUALITY setting and this thumbscrew rocks! Add a dab of glue to make this thumbscrew more permanent.
A simple adapter to turn your optical bench mount screws into thumbscrews. No supports needed. Many print settings & filaments should work well. The photos shown were done with: PLA 0.4 mm nozzle 0.2 mm layer height 15% infill, gyroid…
This is a set of three printable thumbscrew tips for M3 hex socket head screws. This will let you get a pack like https://www.amazon.com/gp/product/B0B5GR9VLC/ (not an affiliate link) and have hundreds of thumbscrews for a reasonable…
During a recent repair of a music stand, I needed to replace an M8 thumbscrew that holds the music stand's vertical post. I found suitable thumbscrews on ebay, but was a bit taken aback by their cost. For my own use, I created the M8…
It's a clamp. Hold something together. You might use a C-clamp to hold two pieces of wood together while you glue them. Or see how tight you can clamp your thumb before it hurts. Possibilities are endless. Clamp Specs: Reach: 40mm Max…
Thumbscrew to fasten the stand of the Samsung Freestyle projector
Simple knurled knob for M4 DIN 933 screw. Diameter: 15mm Lengths: 10, 12 or 14 mm The hex cap screw can be locked with a counter screw. Counter screw is available with slot and 3mm hex Printed in ABS. Layer Height 0.2mm. No supports needed.
FIND ALL MY DESIGNS HERE : https://cults3d.com/en/users/Zuff/creations Do you like my work? Can you support me with a ☕ or maybe a 🍺? It all depends on the time 😄 --- Just a belt tension adjustment screw to customize your printer and add…
![[OpenSCAD] Parametric Velbon Quick Release Shoe + 3/8 Microphone Adapter Thumbscrew](https://media.printables.com/media/prints/349441/images/2970486_b4622e24-bce6-4671-9cb9-7a7c20a88e88/1672022477339.jpg)
