Liczymy pasujące modele…
Alternative sawdust extraction adapter for the DeWalt DCW600, DCW604, D26200, DWP611 milling machine. This adapter has the huge advantage that it does not have to be screwed onto the milling machine, but just clicks. In addition, it has a…
This model is inspired by the design by USSA Design (watch their video here: https://www.youtube.com/watch?v=2JYTYOJt_m4). I made my own so it worked with my Dewalt DCW604 router. You will need to print 4x support screw 4x support screw…
I needed to make some varying sized circle cuts with my DeWalt 20V DCW600 router and found bobmakes awesome model. I am even more thankful that he included some cad files as my made mods so much easier so THANK YOU! I originally started…
Sawdust catcher for DeWalt DCW600, DCW604 to increase sawdust extraction efficiency, which is easy to snap onto the original base of the DeWalt DCW600 milling machine (theoretically it should work for the D26200, DWP611 as well, but I am…
Alternative base for DeWalt DCW600 and D26200 milling machines. I made this base so that I wouldn't have to screw the original base onto the milling table every time I wanted to use the milling machine on the table. Cutting depth…
I recommend 4 top and bottom layers, 3 walls, 30% infill.
This container is designed to catch the fabric which was cutted off. It fits the W6 454D Overlock. Just open the flap and put the nose on the side of the container into the opening. After closing the flap the container is secured on the…
I really don't like dust flying around my garage, routing edges was always one of the worst offenders. This shroud, combined with the standard dust collection port for DeWalt trim routers, will nearly eliminate stray dust from edge…
This is a basic cover that works as is but I kept it as simple as possible to make it easier for people to modify. Facing the printer the right side has the factory tab and a provision for a magnet. Since the left side mount points are…
Circle jig for DeWalt DCW600 DSW604, which is attached to the original guide of the parallel stop and also uses the original locking screw. It is only necessary to melt the nut M3 to fix the circle axis
Water tank cap for W639 that is ideally printed in TPU. Inner most diameter is 74mm. That is the exact size of the original part. Print advise: The fit is a tad loose when using TPU. You might want to print at 98% size in the slicer. (As…
This router base will assist you in routing grooves at an equal distance from the edge of a board. I used two screws, washers and handles that I had on hand. The screws are ¼ inch 20.
Designed a dust collector/extractor assembly for the DeWalt DW6184 fixed router base commonly used with the DW618 router. Uses (2) 1/4-20 x 4" screws and wing nuts to attach the two halves. This design does reduce the maximum extended…
Printed using eSUN PETG +HS, .2 layer height, four walls and three top and bottom layers for the base and two walls and two top and bottom layers for the dampers (BTW PETG without addatives is the bane of humanity). I screwed up the…
replacement part for w638 vito need 1 oring to hold it in place
Shark fin cover for the roof antenna of your W639. Print using PETG, ABS or similar heat resitant material. Two verisons are supplied. 1. The regular one with thick walls ment for translucent filament and a recess to hold the Sika Flex…
Adapter that allows the protruding parts to be milled into a plane. The adapter snaps into place on the original base. Assembly and disassembly is a matter of seconds. At the end of the adapter is a spherical handle that helps stabilize…
Circle jig for Dewalt DCE600, DCW604, which is easy to snap onto the contact surface of the original base without any tools and can be milled with even small circles. It is necessary to screw the M5 screw without a head into the sliding…
My original tether broke after 13 years so i designed a new gas cap tether for Mercedes Vito W639 If you need help how to print this message me Print instructions Printer brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:…
This is a slight improvement to a TP-Link Deco W6000 AX3000 Wall Mount I used but wanted different sized screw holes and cleaned up ends. It will also fit TP-Link Deco X20, X55, X60. This design link has great tips for how to print and…
Simple wall mounts.
This adapter fully replaces the ugly stock phone holder while using its original mounting bracket for very tight fit and hold. I like the Brodit MoveClip system, which i designed the screw placements of my dashboard adapter for. But you…
spare part for mercedes vito 638
A simple wall mount for the Tenda Nova MW6 mesh node. It’s quite a snug fit.
The part number of the w639 glove storage compartment is A6396800291 You can buy a replacement compartment for roughly 120€ from ali express sellers or 250€ by amazon sellers. But we are here for nifty DIY solutions, right? This Repair…
I am re-uploading this model from Thingiverse to preserve Stew675's amazing invention here and so that I can maintain all of the links and information. Originally posted on September 09, 2024. I will not be rewarded with any Prusameter…
Remix of stew675 's beacon bracket, added air duct for stock and Phaetus Conch hotends M3 nuts (fan mount ) and m3 inserts or m3 square nuts (beacon mount ) required to make it work Normal supports needed , all print settings and material…
Replacement cap for the w639 front windshield wiper nut Print tested using TPU 95A .
This is an AMPS mount for carpuride W603 (or W603D). Requires to be mounted from the back!!! You also need: 1 pcs M4 20mm washer (also called wood washer) 1 pcs M4x16mm panhead screw 4 pcs M4 nylock nuts 4 pcs M4x20mm (minimum) screws,…
w638 vito spare part shifter windscreen trim clip
Newly created adapter to precisely fit the stock W639 speaker mount screw holes. Its a recreation of one i bought from aliexpress which broke on first try mounting it due to flimsy and hollow design. Replaces: LAUTSPRECHER…
Qidi Cover – Remix with Hex Pattern & Logo This version of the cover is compatible with Stew675’s project , which allows you to mount a Beacon / Cartographer 3D probe . This model is a remix of the original cover created by @Derek_2843290…
Redirects the air straight up instead of out. The longer model is for the three center sections, the shorter model goes on the ends. There's a slight gap at the very ends because the outer edges aren't perfectly vertical. Though they…
These are Celtic knot bobbin ends for the 3d printer friendly bobbin designed by Maurice for the EEW 6. These are the same designs as on my nano bobbins, but sized up and put on the bobbin ends for the EEW6 from Maurice's printable…
Replacement fan knob for Intermatic SW60MWK 60-Minute Spring Wound Timer, White
‘StarBurst’ design bobbin for the Electric EEL Wheel 6.x. Requires 2x R6 style bearings in front cap and rear Only tension end requires supports. Shaft designed to screw threads together to prevent need for supports. Used slicer to ‘cut'…
Simple medium shelf. Dimensions W:85mm, D:65mm. Prints with no supports. Works well with PLA and PETG. If this was in a hot garage I recommend PETG which will hold up better to high temperatures. Additional necessary components You also…
I remixed the cover linked in the stew675 beacon mount to use some leftover 6x3 magnets instead since i have alot of them laying around. I also made some holes that makes it more lightweight. For more details about the model read the…
DW660 perpendicularity tester A more perpendicular tool cuts better! Tramming tool. Print instructions Unassociated tags: dw 660, mostly printed cnc Category: Parts
This is a multiboard holder for the Dewalt DCW600 compact (palm) router. This is a remix of the drill holder for multiboard by @andrepadua, which is a really nice sturdy drill holder I use for my Dewalt drill and impact driver. I wanted…
Horseman SW612P Technical Camera
This is a circle jig for the DEWALT 20V Max XR Cordless Router DCW600B. The holes are at 2mm increments. You attach it to the bottom of the router in place of the router base, using the same machine screws that come with the router base.…
Tool mount for the MPCNC , all three sizes Change log 10/21/18 Made them a bit more Burly 5/25/16 to fit the universal tool mount. Make sure "up" is mounted right side up. License clearly defined Please have a look a the relaxed "NC"…
Works like a charm since then. Pretty easy to print as well, just print the buttons upside down.
Speaker adapter 165mm (6.5) inner diameter 144.5mm height 25mm
Nach 15 Jahren waren alle Weichmacher aus dem Deckel für den Wischwasserbehälter meines Vito der Baureihe W639 weg und das Teil ist zerbröselt. Hier wäre - falls es jemand braucht - Ersatz dafür. Falls jemand das Dinges verändern…
Prints fine upside down without any supports Tested in PLA but probably longer lasting in PETG because it snaps in This attaches to the pegboard using cleats so it can securely attach to the pegboard. Why? Well when I would remove some of…
Still building the Routertable, updates will follow soon(ish)
Update 2021-02-24: If you're looking for an 88mm height, take a look at Sharkoctopus's remix at https://www.thingiverse.com/thing:4754084 which locks the pieces to each other all the way up. Update 2020-09-23: francisesmodewhite found it…
This model is printed using Overture ABS on OrcaSlicer. I glued a 3mm zinc nut to create a bond with the magnet on the right side of the extruder mount. On the left, there is a mount that can be accessed through the fan hole that allows…
Beacon Simmetric Holder Reworked for QIDI Plus4
Please use STEW675 holder https://www.printables.com/model/1253290-modified-for-attach-the-head-front-cover-with-the
Replacment for Electrical Box Clip A6395450073. In case one of yours broke or went missing. Print in PETG or ABS to ensure temperature resistance.
A useful print to hold indicating desiccant. When the desiccant changes color and has absorbed all the water has held it needs to be dried out. This typically involves laying it out on a cookie sheet and putting it in the oven for a…
Used @DIYwithJJ's instructional video to combine @KajasX's dust port attachment for DeWalt DCW600 DCW604 with @PouOu's excellent DeWalt Airlock Adapter (male end). The male airlock end is the same dimensions as on my palm sander DCW210,…
My W639 Vito's battery cabin door latch was missing. Decided to model one based on other side's latch. Printed in ASA. I guess that ABS and PETG works as well. I don't recommend PLA due to cabin getting really hot on summer. I suggest…
3D printed compas for DeWalt DW621 router. Compatible with originals 8mm rod.
Film advance lever for the Fujfilm 6x9, 6x8 and 6x7 rangefinders. Modern III type. Will not fit older models. Print instructions I print mine in 0.1
Simple hand wrenches for the Dewalt 660, 611 and Bosch PR20EVS routers works well with 2.5 inch endmills and v bits. The tip of the tool needs to be smaller than the nut. **Dec 2, 2020 updated fit and added .25 inch bit shank holder.…
Printed on my Bambu P1S using PETG. Some filaments spool is bit tall, so I would suggest to print 83mm though 73mm can fit most.
It fits the Dewalt DW682 quite good. With my machine even better than the original adapter, which comes off while working - sometimes.
A0029880181 Clip für den Daimer, gedruckt in PETG oder PLA, ca 15 min.
This adapter has been created to prevent Overlock yarn spools from wiggling around and eventually falling off when using them on regular sewing machines. Overlock Yarn Spool Bottom Diameter: 33mm Top Diameter: 25,5mm Spool Height: 123,5mm…
this build is done with the teensy lc, ws2821b leds, 2 rotary encoders and everything else is just handwired together the built in usbc to micro usb adapter is this one: https://www.amazon.de/-/en/gp/product/B07MYWT4GK blog entry:…
W6 External Thread spool holder W6 N 2000 / 3300 (30 Prg) / 3300 Exkl. / 5000 / 6000 / 8000 / 9000 W6 Product No : W-E-EXGARHALT Is your yarn of good quality, but still snags and constantly breaks when running? Then you should use the…
Collets organizer which I use for the DeWalt trimm router DCW600. This organizer fits exactly into the TSTAK carrying case. A piece of foam must be glued to the carrying case lid, so that the collets do not fall out of place in the closed…
This is a small case for the Wiznet EVB-Pico2 boards. It provides easy access to the two buttons but covers the LEDs (I printed it using transparent PETG). The pin headers are also covered, though there is some space above and below the…
11/27/2025 -- I printed the Dewalt base but my handheld router did not fit on top of the jig... the base was too large! So I removed the one that was there and uploaded the new base that will fit the palm router and with the screw…
Dies ist ein Auffangbehälter mit Extrafach für die Overlock Nähmaschine N 656D aus dem Hause W6 Wertarbeit. This is a collecting container with an extra compartment for the overlock sewing machine N 656D from W6 Wertarbeit. Print Settings…
Um die Clamex-S Verbinder von Lamello zu nutzen benötigt man eine 8mm Nut. Mit der Flachdübenfräse wird zuerst ohne die Distanzscheibe und dann noch einmal mit der Distanzscheibe gefräst, dann passen die Clamex-S Verbinder in die…
base for spinning top Dewalt DW618
I was excited to outfit my Qidi Plus 4 printers with Conch nozzles, but found rather quickly that they leave a space in-between the new hot end and the front carrier plate. I use Stew's front end carrier plates, as well as most of his…
Adapted (re-created) DW660 mount based on DW660 Primo mount , and then modified to fit Lowrider 3 carriage. Licensed CC-BY-NC-SA because it is derived from models with that license.
A 2 bay QNAP NAS bracket for the QXP-W6-AX200 Wi-Fi card
Jednoduchý adaptér který se přišroubuje místo originálního průhledného plastu na spodku frézky. S frézkou je pak možné pojíždět po vodící liště, která je součástí příslušenství k ponorné pile DeWALT. Materiál: PETG, ASA Vrstva: 0,2mm…
This tray is a resized remix of @sblomfield trays for the Commercial Chef CCD100W6 / Westinghouse WFD100 utilizing infill meshing. It is sized to fit precisely between the stacked plastic trays which come with the dehydrator. Top and…
SW6106 Board is Glued with B7000 (you need to file 2-3mm off the sides) Single Click Turn ON Double Click Turn OFF HOLD 5s Turn ON Long time You need 4 Screws M2 SW6106 Board Brass inserts M2 Print Settings Printer Brand: VoronDesign…
Replacement for the Oval Type Sign on your W639 Mercedes Benz. The base model is just blank. Engrave your logo or custom text using the PrusaSlice 3mf. My company logo provided just as demo. Install using double sided tape. Replaces…
Remix to mount on a Dewalt DW618 plunge base, No bushing guide needed Better dust collection (bigger opening) Fixed to the router Replace the orignal router plate with this one (use original screws) I made two version as the pegboards are…
Replacement for A1697420181 used in Mercedes Benz Viano / Vito. The advantage over the original part is that you can easily scale this model to fit into corroded and other wise enlarged stock holes. Ideally print in TPU since the part is…
Simple model that lets you mount your Carpuride w603d and a tire pressure monitor to an ibex 450/450MT. It includes a camera mount for the front camera. The windshield is still fully adjustable and just clears the camera wire when fully…
Quick fix in case your rubber gasket to hold the rear wiper in place and seal its break through went missing. Its not meant as a permanent replacement since the TPU we can handle is not as soft as the application requires. The original…
Having lost the locking mechanisms of the fuse box located in the engine compartment of the Mercedes Vito W639, and not being able to find the closure clips online — nor wanting to buy the entire box — I decided to 3D print them. I know…
When I accidentaly connected battery to receiver with opposite polarity, I created this casing, that it cannot be done anymore.
Danke an @ingegneredent_146676 und Peter H fürs teilen. 125-mm-Staubschutzhaube für den Winkelschleifer Metabo W680 oder Nachfolger. "Version 1" m it Anschluss für Festool Anschlussmuffe oder "Version 2" mit angepassten superschnellen…
Hey everyone! I always wanted to have bullet dices, but I didn't like the published ones. And of course I needed a matching box for the right look. The magazine holds five Dices. In the current version, you still have to buy a spring.…
It is the maximum size of plate that my Bambu P1S can print.
DeWalt DCW600 holder in carrying case. I was looking for a suitable case for the Dewalt DCW600 milling machine. The original case for the DCW604 seemed too big to me, so I decided to modify the classic DeWalt case from the cordless drill…
Recently I needed to fit a large number of door hinges so designed an adjustable jig (link at end of text) that needed a depth controlled router fence/baseplate. None of the baseplates I could find suited my needs hence this model design.…
Camper Van Side Window Ventilation Insert / Grille A practical side window ventilation insert designed for camper vans Mercedes Vito. It provides fresh air flow while keeping the interior secure and weather-protected. Perfect for…
I tried the keyplate and also let a small child test the lockcard wallet extensively. Shaking and throwing the wallet from a few meters high. For overlong keys, like the RW6 the keyplate is unsuitable, the keyplate is too small and can…
Replacement for the usually gooey or brittle 42mm plug used to seal 42mm holes in the wiper compartment of W639 Viano and Vito. Might fit other Mercedes Benz models BEWARE, this is made to print in TPU/Flex. Using any other non flexible…
Na přípravek se originálními šrouby připevní tělo frézky DeWalt DCW600. Do materiálu pro opracování předvrtáme otvor průměru 1,5mm ve středu zamýšlené kružnice či oblouku. Jezdcem nastavíme poloměr otáčení frézky. K výtisku je zapotřebí…
This is a Sewing-pedal-holder. It holds the sewing Pedal of a W6 N8000. I Version 1 is for Screwing it in and not getting it out (More rigid for Kids in household) You need 3 Screws: 1 x 70mm (max. 3mm thick) 2 x 35mm (max. 3mm thick) Its…
Spare part for W6 sewing machine N 8000 Exclusive. Possibly also for other machines. Simple printing with TPU, if it must go quickly for example at the weekend. Do not press forcefully on the thread spool holder, so as not to damage it.…
Hier habe ich einen Absaugadapter konfiguriert für die Dewalt DCW604 NT Akku Fräse auf den OSVAC Verschluss. Der Adapter ist sehr passgenau und rutscht beim Arbeiten auch nicht heraus. Es sind zwei Dateien. Eine mit Logo und eine ohne…
Printed on Bambu Lab P1S .4mm nozzle .12mm layer 15% infill Ironing turned on PETG Material
This is a pen holder that snaps into the dewalt router plate that is standard for the low rider V2. Just pull out the router (or retract it if you have a short pen) and snap in the disc from underneath. Compatible with my Z-Probe so it…
Repair your broken A6398800985 by glueing this part onto the breakage. It will work with just superglue. But for extra strength, drill 1.5/1.75mm holes through the lashes and stick some filament through the lashes. Apply more superglue or…
![W639 - 42mm plug - A1009870044 [Scheibe] - Vito / Viano Mercedes Benz](https://media.printables.com/media/prints/9efeb331-90d2-427e-98a7-7c6ae16ee987/images/9725173_94da1573-0068-43e2-a5ca-d3a95fc459fe_2315b8ff-fb92-4834-8458-d30913b8157e/img_5162.jpg)
