Liczymy pasujące modele…
Various designs for XT30 connectors Here you will find my designs for the XT60 size and MR30-M . News 12.03.25 Step files available 22.11.23 added design of angled and round mounting bracket 02.11.23 added design of standard mounting…
A purpose build XT30 2+2 plug designed for the 🥰 BTT SB2209 / SB2240 toolhead boards. Built with a minimal footprint to keep your cable routing clean and uncluttered. Companion Model: Use the Cable Bridge PLUS to form a sleek and ultra…
Files for the XT30, XT60 and XT90 are now here…. EDIT: 8/10/22 Created the parts with raised letters. Mark them with a felt pen to make them easy to stand out. I got tired of fighting to keep the plug and wires in place while soldering…
EZ to Grip XT60 and XT30 Caps to cap, cover, and tag your batteries especially when you travel. Printed in PLA UPDATE: 2 Versions - TPU VERSION - adjusted for a snug fit! Resolution: 2 Walls/Perimeters - 3 or 4 top/bottom - .28 Layer Height
I made this small XT30 panel mount adapter as I need one to mod my Bambu. To install the connector inside the adapter you'll perhaps have to file a bit the connector to fit it, but for sure it won't move. I strongly advise to print the…
Most XT30 housings on Printables are designed for bulky RC/drone battery leads, typically using 14–16 AWG silicone wire for relatively high-current RC/drone applications. I needed a connector housing for a much thinner cable — an aquarium…
Remix of XT60 Plug Housings resized to fit TX30. I printed it in TPU and the fit was really snug, non-flex materials might need ~1% upscalling.
…Please be sure to hit like & post a make, I'd love to see your prints! Print standard VORON settings, no supports required!…
This is an XT30 / XT60 / XT90 Cap, it fits over the female side (battery side) of lipo batteries. It has a small lip on the bottom to make it easier to pull apart. Should fit snug. I use these to determine if the battery is charged or…
Designed to fit the Amass XT30U-F model that Tattu uses in the smaller batteries. Dimensions from the technical drawings with 0.1mm tolerance.
Printed with no supports, .2 layer height, 4 top and bottom layers, 3 side layers, 40% infill.
Kappen für XT 30 Stecker. Kann für beide (Stecker und Buchse - siehe Bild) verwendet werden. Die Stecker werden einfach nur in die Kappe gesteckt und halten so recht gut. Am besten mit der kleinen Seite (Kabelausgang) nach unten slicen.…
Battery caps for XT30 conector it protects the conector and if you use a color code you can identify if the battery is full (green) or empty/to charge (red). Quality TPU really makes a difference in these small parts. I use sainsmart TPU…
I saw a YouTube video of people using the lens from a disposable camera and combining it with their camera body cap to make a new lens. I decided to 3D print one instead. After four iterations, I got the right thickness to work with the…
Layer Height - 0.1mm Infill - 20% Recommended Material - ASA or PETG
The Fuji X-T3 is a great little camera, but lacks an Arca-Swiss mounting plate. Also, the grip is a tad small, would benefit from a bit more beef. This newly designed grip provides both features, yet doesn't block access to any of the…
XT30系列尾套外壳， 使用ABS耗材打印，喷嘴0.25 ~ 0.4mm。 XT30 series tail boot casing, printed with ABS filament, nozzle 0.25 ~ 0.4mm。
Note: XT30U-F are conventionally power outputs , not inputs. You don't want live pings exposed when the connectors are exposed. So don't use this to power your project. Thanks to niZmo for pointing out this omission. M3 mounting hardware.…
I'm running multiple tools and found that the BTT provided cables were unshielded and interfering with each other when rubbing against one another, causing bus communications to freak out. I made new cabling with some LDO FEP cable, but…
Taking the opportunity of upgrading from i3 to MK3.5, i decided to rework the way i connect my PSU (which is relocated outside of my LACK enclosure). The new board has metal case, and thus must have the earthing line added, so my old…
Kayoumini 2.5 XT30, DJI O4 antenna and ELRS holder
I redesigned the antenna mount for easier storage and transportation. 20240902:Upadted Folding Antenna Part 2.
This is an XT30 cap to prevent shorts when keeping LiPo batteries in a bag and to indicate charge. It's ribbed for easier removal, even with a tight fit. Also included is an STL as a regular cap instead of a doubled one. Pause the print…
XT30 Connector case I have made 2 designs, one is for a round wire that is approximately 3.5mm and the other is for a 16AWG/1.5mm2 wire (the proper wire thickness for xt30 according to the connector datasheet). Print settings used:…
I have a Braun XT3. It comes with attachments size 3 and 5. But I wanted something in between. So I created this model. It is not easy to print because of the fine details. I would recommend printing it in ABS for more rigidity. It worked…
Some simple designs of a cap for XT30 and XT60 batteries to help protect the ends. Perfect for FPV. Printed in TPU at 0.2mm Layer height on a Creality Ender 3 Neo. 100% Infill for best results. If you print this in any other material let…
to install xt30 Male you have to cut off the bumps (for female such actions are not necessary)
Needed somewhere to put the xt60 on my Grinderino..
It's a snug fit. Once it's inserted it will snap into the gaps and won't come out. I recommend soldering and do your wiring first, before fitting it into this connector.
I didn't like the stock heat shrink that most XT60 to XT30 adapters come with so i designed and printed this in TPU. Print in TPU can be printed without supports but printed better for me with supports turned on. Easily to install, remove…
Antenna mount for the Foxeer Lollipop 4 antenna with short tube and UFL connector for the ImpulseRC Micro Apex Frame
My Baby Ape didn't come with the little antenna tubes, so of course by the end of day 1 I'd tangled one of the trailing RX wires in the prop and torn it off :( Hence this stubby sharktail that takes the place of the TPU one that comes…
I got a SB2209 USB with a broken cable right before Chinese New Year and had no customer support for weeks, so I had to make my own cable by replacing the plugs on a 65W shielded USB-C cable. XT30 2+2 requires soldered power wires but…
Recommended Print in TPU. No supports needed, Pre orientated. Separates Voltage and Ground. Securely holds XT30 to Capacitor. Solder Capacitor to Pigtail. Press into TPU. Solder to ESC. Capacitors seems to come in at different sizes with…
This housing lets you make a triple XT30 connector. I use this one for extending the PSU cables of my MK3. Print …at 0.2mm using a 0.4mm nozzle. Feel free to use any solid filament. Support is not required. Additional parts / equipment…
Crashing my Volador VX3 FPV quadcopter repeatedly caused my camera to change angle or get damaged, so I designed this thing. It fits Walksnail Moonlight with filter, or any other 19 mm FPV camera at fixed angle of 30°. Integrated lens…
A double sided battery cap allowing you to keep track of batteries that are fully charged or depleted.
I didn't like how the power cable was getting pulled so I made it fixed to the side of the drone. Petg works fine. TPU is best. PLA is not suggested. any suggestions to make it better are welcome!
XT30 to XT60 connector for fpv. STL is 5mm high STEP for change to your desired height Print in tpu with good profile
Remixed a nice base design. Made the antenna hole a bit bigger so it fits easy without slipping out and made it way longer, so the antenna stays secure. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No…
This is a very clean install as you can see from the photos. I prefer this to the 3D printed XT30 mount provided by IFlight/Chris Rosser as this allows for a more central battery position (centralizing the weight balance) and also this…
Information The other designs I saw with a holder for the balance and/or XT30 connector had only one of the connectors on the strap or not at the right place. So I just modified the version with the balance connector and added an XT30…
This is my full TPU set for the pavo20 pro II. It is designed to provide protection and longevity, since I use this as an actual cinewhoop for filming jobs. Adds some weight, for me thats worth it on a cinewhoop. If you want to freestyle…
Printing without supports To install xt30 Male you have to cut off the bumps (for female such actions are not necessary) Cut off the skirt near the contacts
This is a little design I made to extend the meagre battery life of my BetaFPV VR03 goggles. It's a sturdy, closed design, it clamps down tightly thanks to the M3 screw, it's reasonably compact and easy to build. It's easy to carry too…
Beschreibung des 3D-Modells Finne mit Antenne und XT30 in einem. Sehr stabil und für einen ordentlichen Copter. Die Halterungen, die unten am Frame liegen, müssten Abgeschnitten werden damit der Akku besser reinpasst. - siehe Bilder. Es…
I use these buck converters to power lights from self-made powerbanks with XT30 output. So I needed a housing to deploy them. This is a tight fit with minimal footprint. Print in PETG to accommodate for heat produced by converter.
inspiration: https://www.printables.com/pl/model/518869-xt60-pulling-grip I plan to make versions for the male part of the connector.
Designed these some time ago for various projects. There are different versions of the inner part. The XT30 Version allows the usage of spade connectors as contacts and powering your device with a wall plug. The other inlet is designed…
My friend and co-worker has 3 Yamaha dual-sport XT350s. And one intake cover OEM P/N 30X-14412-00 (zero stock). He has tried aftermarket air cleaners to get around the issue but apparently that requires some carburetor tuning and he would…
Für die Isolierung statt Schrumpfschlauch bei XT60 zu XT30 Adaptern für beseren Gripp. Hergestellt aus TPU. Da kann man eigentlich nicht mehr viel zu sagen. For insulation instead of shrink tubing on XT60 to XT30 adapters for better grip.…
An easy print of an XT30 female connector for any kind of rc model DO NOT SCALE
What it is: A compact Arca compatible tripod plate designed around Peak Designs Anchor mount for fujifilm XT2 and XT3 cameras. The Peak Design Anchor mount allows you to mount your camera strap or wrist mount to the bottom without…
Safety cap for XT30 male / female connector, with a wire loop so you won't lose it when removing for use. The loop is large enough to go through an XT30 connector so it can be added after soldering. Printing material: TPU. I haven't…
A cap for your XT30 batteries, that indicates whether it's charged or not! I printed this in PETG on my MK4S with a 0.4 nozzle and it fits quite snugly, any other material should be fine, but PLA might creep, I haven't tested it. You can…
This is a 2-part design Part 1 - Antenna holder for a small ELRS T-style antenna. It's likely others will fit just fine. Attach the antenna with cable ties The antenna is meant to fit partially under the main bottom frame and the bracket…
After installing the EMAX TinyHawk & TinyHawk II FreeStyle VTX/RX Sled I didn't find an easier way to mount the XM+ Ante
These are accessories for the GepRC Tern LR40 drone. The Fusion 360 model files are included to allow modification for other quadcopters, buzzer sizes, or antenna arrangement. Prints are made from TPU to allow flexibility for parts…
Since I'm using a QX7, I wanted to have a charge block which fits all my needs. So I've done this remix. Thanks for the original design. I also changed the bottom of the block, to make it easier for soldering. Have fun!
I've bougth SKYRC B6neo 2 charger (awesome thing!) that comes with 8-in-1 charging cable and was shocked that the cable does not have any caps so it is very easy to short curcuit when charging batteries. So I modelled caps for most of the…
Simple spacer to insert XCORTECH XT301 tracer unit to G&P QD Silencer
Sealed/waterproof case/holder for XT30 male Thread: М16х2 - 8mm Thread for fixing: М16х2 - 6mm For sealing needed O-rings 16-18mm x 1-2mm Recommended PET/PETG Сable AWG-16 In the photo (the safest for this sealed) You will need to grind…
Added a cap for the H7 bulb, to prevent it from damage! Added two versions with a slot for a voltmeter. Links below! I used this H7 car bulb for some months as LiPo Discharger or Killer. Since it works pretty well I decided to design a…
An XT30(2+2) for compatibility with ERCF/SB2209 canbus cable, two microfits for EBB36 and AFC-Lite wiring order.
Simple mold for XT30 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.12 Infill: 25% Filament: eSUN PLA Category: Electronics
Da ich die Drucker öfter aus ihrem IKEA Lack Enclosure heraushole, musste ich eine Schnellverbindung mit der PSU schaffen. Benötigt werden: 2x M3x15 Senkkopfschrauben 2x M3 Einschmelzmuttern 2x XT30 Stecker 1x JST BEC Stecker Ebenso Kabel…
Hi there! Just a simple mount that lets you secure your XT30-plus, as well as an antenna (3mm diameter) - in my case the one from the Caddx Vista (Nebula Pro Nano). Enjoy! Category: R/C Vehicles
Top Plate with integrated battery holder (HRC Power 2S 2400mAh) Verlcro straps: 140x10x1,5mm Integrated XT30 mount so you dont have to fiddle with the connectors... just glue in the XT30 on the ESC side. (Press fit+glue, im waiting for my…
Print, then drill the non-counterbored half to 1.5mm, and the counterbored side to 2mm. Then, use an M2x6 mm socket head machine screw to clamp the shell together around your cable.
Clean solution for the power connector. I glued it using epoxy but you could also adjust the size of the hole for a pressfit. Print Settings Supports: No Infill: 10% Filament Material: TPU
You will need JST 3s and 4s connectors for the balancer and also XT30 Plugs to charge the batteries. I glued all the connectors in place with epoxy and then soldered the cables. I did't have to glue the bottom and the top plate together,…
XT30 Straps mount - for 11mm straps *step file included to fit your straps
xt30 mount for 20mm strap, check my project for the x60 version.
Nice little cap holder, super light coming in at .8g with my tpu, super light compared to what I could find out there. I like to use a tiny bit of heatshrink to keep the leads semi isolated, and it works good. print at 100% infill, 0.4mm…
Simple case for a module you can find by searching "Dual USB DC-DC 12V 24V 48V 72V 80V to 5V 2A" on your favorite direct-from-china shopping website (Ali*xpress, ebay..). I mounted it on my ebike for phone charging.
power supply (https://www.aliexpress.com/item/1005004886963358.html) M12 cable gland (https://www.aliexpress.com/item/1005003263360717.html) XT30 connector 2 pcs square M3 nuts (to be inserted in pause) 2 pcs M3x6mm bolts
power supply (https://www.aliexpress.com/item/1005004886963358.html) M12 cable gland (https://www.aliexpress.com/item/1005003263360717.html) XT30 connector 2 pcs square M3 nuts (to be inserted in pause) 2 pcs M3x6mm bolts switch…
D.I.Y. -- XT-30 2S LiPo parallel Charging Board. Category: R/C Vehicles
added xt30 to the rip n dip mount.
This model contains 3 mods to A4T you can pick and choose from 1. Sidecar PUG Mount for A4T+WWBMG I wanted to use PUG with my A4T on a Trident but I wanted something rigid and with minimum use of z-height about the toolhead. I created a…
TPU print Print with support 16/08/2024 : Version 2 add 4mm lenght to protect connector reinforcement of screw housing
xt30 and antenna holder one is inline and the other is set side to side. Have thinner lighter versions as well.
Holds the lipo 2s (550mah) the cap and the Xt30 TPU is better. Category: R/C Vehicles
A simple and easy way to keep track of the charge status of up to 4 separate XT30 batteries
XT30 Link Insertion Tool Designed to allow for a more positive insertion of a recessed power link, leading to a more reliable device.
Designed for the Lightning 2 FPV drone to be light weight, easy to print, and hold the XT30 and VTX antenna. Support my work: All of my models are available for free. If you'd like to show your appreciation, consider Buying Me A Coffee.…
The Design This is a two-part design, with the VTX antenna holder separated from the buzzer and XT30 mount. This makes the parts easier to print and gives you more flexibility. The buzzer mount is designed for a 9mm buzzer. The Build…
Printed bite cap for Coast XT30R flashlight. Print with TPU filament.
Minibyte 25 drone backpack for xt30, vtx antena and capacitor
TPU grip designed for Maxxframes M2 XT30 battery connectors :D i was having trouble getting the batteries off so i made this! i highly recommend printing extras because of how they go on. there is an edge on the inside of the grip to…
This is a mod to attach a DIY detachable remote pressure switch to the C8 flashlight. The printed parts replace part of the stock rear switch assembly. You are also going to need XT30 connectors, and some metal strips (like those they use…
to install xt30 Male you have to cut off the bumps (for female such actions are not necessary)
Crashing my Volador VX3 FPV quadcopter repeatedly caused my camera to change angle or get damaged, so I designed this thing. It fits Walksnail Moonlight with filter, or any other 19 mm FPV camera at fixed angle of 30°. Integrated lens…
xt30 and antenna holder one is inline and the other is set side to side. Have thinner lighter versions as well.
Yamaha XT350 Wall Art; can be scaled easily and can be hung or stand alone. I also take requests If you like and enjoy it, feel free to rate/boost (it really helps)
Kayoumini 2.5 XT30, DJI O4 antenna and ELRS holder
Eliminate the risk of prop strike on the battery leads with this TPU Battery strap with built in XT30 or XT60 connector holder. I use it on the Proto25 drone. Note: This is a remix of a ProtoFPV STL - Not for commecial use / resale…
What it is: A compact Arca compatible tripod plate designed around Peak Designs Anchor mount for fujifilm XT2 and XT3 cameras. The Peak Design Anchor mount allows you to mount your camera strap or wrist mount to the bottom without…
