41,198 models
A Multi-Use Case can't fit every situation. Because of this, I designed this toothbrush travel case in the same style as my Multi-Use Case . I have designed it to be as compact as possible, but still fit as many styles of toothbrushes as…
Original model was good, except for the hinge, it's a perfect candidate for printing in place. That's my first print in place model, so any hints, makes, comments are very appreciated! Print settings PLA 0.2 height 3 perimeters 30% infill…
This is my design for a case for holding Gridfinity bins. My design goals included: Clean design No Hardware Able to stand on ends and back Contents stay in place Easy to open and securely close Stackable Designed for 3D printing While I…
Simple protective case for the Flipper Zero Wi-Fi Module v1 development board. Flipper Zero Wi-Fi Board Docs: https://docs.flipper.net/development/hardware/wifi-developer-board Models Available: Full Case Requires 4x M3 screws/nuts for…
A small, strong case with a collection of optional inserts for different uses. Case Use a section of 1.75mm filament inside the hinge to connect the lid to the base. Depending on your printer/setup, this hole maybe be on the tight side or…
Screwless Snap Assembly. Start with base or bottom case, remove ssd and drop Pi4b board into bottom case so that it rests in provided IO openings correctly. Fit should keep board in place even with a little shake. Place…
Slim Arduino Uno Case Overview: -This sleek, two-part case is specifically designed to house and protect an Arduino Uno. It's compact and streamlined, ensuring your Arduino remains secure and accessible. Assembly Instructions: - Required…
24.05.2021 update: case was designed for the raspberry pi zero W, it will not fit the older raspberry pi zero (different SMD board layout). a remixed version that will fit the old pi zero and also adds cut outs for the pin header can be…
I DM for a group of players new to TTRPGs and saw that they tend to need help finding the right die to roll or end up using the wrong ones for their actions. My goal for this case was to reinforce the differences between the dice and to…
OpenSCAD sedigned case for the esp32 development board. Thanks to Sergio Vilches for the rounded corners!
UPDATE 12 November 2023: I've received a consistent handful of messages from people who have been downloading the wrong original files so I've reuploaded the correct lid/seal files here as well. UPDATE 13 July 2023: Added a version with…
ESP32 Devkit V1 Case w/ Snap-on lid with button detents and cutouts for USB, LEDs and pin access. This case is thick enough so that the pins are completely shielded inside the case, though accessible for connection. IF you want a version…
I liked the remix from ANBAL534 ( https://www.printables.com/model/207028-steam-deck-carrying-case-insert-for-eu-plugs-europ) but missed the option to use the case as a stand as well. Besides that I don't use full SD cards, I opted in…
A NEW VERSION OF THE CASE A V2 is Available HERE : https://www.printables.com/model/1120097-flipper-zero-case-v2 SnapBumber for WifiModule : https://www.printables.com/model/392270-flipper-wifimodule-snap-bumper-v10 i'm learning 3d…
Chose one of 3 designs to download for the Samsung Galaxy S22, S22+ and S22 Ultra are incompatible. All 3 cases work with wireless charging, have exposed power and volume buttons, and have a lip to protect the screen. None of the variants…
After seeing many other container projects, and old products like the Dutch Roly Kit, I thought I'd try my hand at designing my own. I spent weeks worth of manhours working on prototypes and iterations, so please, if you really like it,…
Screwless Snap Assembly. Start with base or bottom case, remove ssd and drop Pi4b board into bottom case so that it rests in provided IO openings correctly. Fit should keep board in place even with a little shake. Place Screwless Jack…
2 part sleeve case for the Raspberry Pi 3, their spilt in the middle of the headphone jack. The 2 parts of the case slides over Raspberry Pi, and held together by friction between the 2 part of the case and the Raspberry Pi. So no need of…
Für meinen Virtuellen Flipper (VPin) habe ich eine einfache und kompakte PC ATX Halterung gebraucht. Es sind vier Druckteile notwendig. Das linke und mittlere hat eine Aufnahme, um das Netzteil darunter festzuhalten. In dem Beispiel ist…
Pill organizer / vitamin reminder with a labeled slot for each day of the week. To use, loosen the screw 1 turn and twist the lid to the current day. The lid & screw are fully removable to refill the container at the end of the week. To…
Fits Raspberry Pi 4 B and Hat (SenseHat) This Case also snaps to Domed Top from ... "Raspberry Pi4B Case for Noctua 40mm x 10mm Fan" Toggle and access for camera and GPIO and Toggle. Screws... Pi takes M2.5 (a set of 4 screws and nuts…
One more case for Raspberry Pi Zero. This is simple, compact and quite rigid. The cover part has press fit with the main case. The board sits on four pins and from top is pressed by the cover part. Nominal clearances between the board and…
Galaxy Buds Case that snaps on. No glue or tape. It will fit Buds Pro, Buds Live, Buds2 and Buds2 pro, and Buds FE. I printed in PLA. 0.15mm QUALITY settings in Prusaslicer. Ironing for top layer only. Supports so it can be printed easily…
This is an Arduino Uno case made in Fusion 360 following this tutorial by Taylor Stein:
Why YZ Case ? I wanted to create a Bear Upgrade, at no cost... once the Power Supply was removed, (Keeping it out of the heated enclosure) I needed a bracket to tie together the missing structure that the Power Supply provided. The YZ…
This case fits the Teyleten Robot ESP32-S3 Development Kit sold by Amazon… https://www.amazon.com/dp/B0B6HT7V7P?psc=1&ref=ppx_yo2ov_dt_b_product_details This development kit has two USB-C connectors without the pins soldered to the board.…
use 1.75mm filament as hinge pin. Unsaled model holds cards up to 89mm x 58mm. Its perfect to add personal Text. I did one with two color printing with one extruder. Following the instruction on https://www.youtube.com/watch?v=0Sla-vIsvh4…
The story: Wanted to print small case for condoms which could be thrown in a bag and forgotten about without worry that the condoms will get damaged, because you know you should not keep condoms in a wallet. I could not find a single…
What is that? What's in there? Well in that case. __________________________________________________________________ 🧡 Let’s Both Earn Some Prusameters! If you like this model and are thinking about getting a new Prusa printer, use my…
Sewing Cloth Tape Measure Winder Case 14mm and 18mm. Super simple two piece snap fit. Assembly (see photos): Push tape through thinner slot, same side as winding hole. Fold tape and reinsert from back. Pull tape tight trying to keep the…
Remix of the Weekly Pill Case / Organizer with Personalized Monogram Screw by printfutura , whose design was inspired by the 7-Day Pill/Capsule/Tablet Dispenser by Jambeetle and the Parametric Pill Boxes by pmoews . I take lots of big…
A Multipart Pinecil Case remix that is a bit taller (+5.2mm) with a different set of cutouts and accessories allowing a full set of spare tips to be stored. The dimensions have been change to allow clearance for a 2nd tip mount which…
Update 03.02.2023 Added additional model, “rugged”. This one has thicker walls and an improved snap lock. It uses a little bit more material to print compared to the original model. Both models are available for download. Description…
I made a remix to fit my ESP-WROOM-32D because the ESP won't fit with the original case. I also changed the fittings a little bit so that it can be easy reopened.
14 Infill Samples with a case. Everything can be printed on a Prusa MINI . Simply download the 3MF file to PrusaSlicer and change the printer type. I had great success printing them in batches of 2 at a time (split left and right) and I…
I wanted a slim case for my Geekcreit® ATmega328P Nano V3 (a copy of the Arduino Nano board you can find on Banggood). I also wanted a case for situations without pins, but an output cable directly soldered on the board : I did this one.…
I needed a game case holder for 14 PS4 cases but only found designs to hold 10/12 cases on here & Thingiverse. I didn't want to print multiples or consume the time/material required for existing case designs, so I made my own. This holder…
Marius' really nice Zero W2 case model only comes with a screw-fit back, whereas their Zero W case comes with either snap-fit or screw-fit backs. I tried using the back from the latter model but the pegs were slightly too large (~2.4mm).…
Micro:bit case for the second version of the board Supports the new features of the card: - microphone - speaker - Touch logo Remixed from https://www.thingiverse.com/thing:3028078 and https://www.thingiverse.com/thing:3511591
Maximum HDD dimensions: Length 148 mm Width 102 mm Height 27 mm HDD is attached from bottom with a 95.25 mm by 44.45 mm screw pattern. Check if your hard drive fits and has this mounting pattern on bottom. Printing To assemble one case,…
YubiKey 5C NFC Case/Keychain (USB C only) I needed something to protect my YubiKey from random bumps and scratches in my pocket. Printing in different colors to differentiate them. It is intended to use case cap as main holder of the key…
The main publishing location for this model is on GitHub. Go to the GitHub page of this model for the latest updates, Blender source file, and more detailed instructions. Go to my site for an overview of my other models . Only a few of…
This case has 4 versions: Plain : No cutouts and no mesh Plain cutouts : This version also has no mesh but it has slits for GPIO and camera cables Mesh standard : A mesh is added in PrusaSlicer to the 3MF files. This only works when you…
I was looking for an Raspberry Case that could fit the Pi and a Stepdown (Buck) Converter to power the Pi directly from the power supply of my MK3S. I couldn't find anything I like so I decided to create my own. I designed 2 versions of…
UPDATE: Check out my new and improved version here . I designed this display case to hold and showcase nine Apple Watch bands at a time. It is designed to fit most band types and lengths, though there are many first party and third party…
Flat version of the Domed Cover...SnapAssy. Please NOTE! Remove the MicroSD Card before assembly and disassembly! You will need... Noctua 40x40x10 MM Fan 5V 2 Dupont female single pins to connect to 5V or 3.3V and Ground GPIO pins. You…
This is a remix of the fivesixzero's Case for Flipper Zero Wi-Fi Module to use it with Ruthex M2 threaded inserts and M2 screws instead of M3 screw + nut. The screws needed are M2x7mm. I also made a version with the Marauder Skull logo on…
Case for Noctua 5V 40x10mm 4 pin Fan... Snap together assembly, no screws required. CPU stays very Cool. 36C during stress test (100% Fan) Screwless! Frame4Fan-SimpleNoScrews-Assy Frame with posts, does not require screws for the case and…
This Case fits a Raspberry Pi 3B and also fits a SenseHat Board and has a second cover for GPIO, Camera and Toggle access... Top vents mirror display grid. Case is designed for Screw down and will accommodate the board without screws.…
If you like my design, I really appreciate if you can consider a coffee ☕ for me! ( LINK ) Version 2 released! Snaps on sides, slightly easier to open. Overview A business card stand for an exhibition booth or an event table. It folds and…
Edit 06.05.2023 : Added STL with 0.2 tolerance on all dimensions I couldn't find a pixel 7 case thin enough for my taste so I decided to model one (with my very limited ability to do so). There is two versions, one flat around the screen,…
Protective case designed specifically for the TP4056 charging circuit. Featuring a entry point for USB cable, a dedicated exit for power cables, and a secure pressure fit design. With this circuit things can get quite hot so i designed it…
Important: Please check the pictures how to change the print settings for a successful print :) There will be an imprint on the first layer, for that you have to place the surface on the bottom and set an outer rim of 15mm. With those…
Case with Snap-on lid. Lid has detents for buttons. Case has cutouts for USB, LEDs and pins will stick out of back of case. If you want a version of this case where the pins are fully shelled/enclosed - see:…
This is a press-fit Pi 5 case, with customisable options for vents and ports, that also supports the optional active cooler. V1.1 has more tolerant clearances, less crush ribs and a slight taper to the longer pins. V1.2 has no specific…
RPi 'Z-BOX' The RPi Z-Box, designed for the 3B & 3B+, is the first integrated case for the Raspberry Pi that attaches seamlessly to your Prusa MINI/MINI+. The Z-Box attaches at the base of the z-axis and replaces the lid of the stock…
UPDATE - 3-15-2023 This case is meant to be a little loose in order to protect your expensive in-ear monitors or earbuds from getting tossed around or wound tightly which can add wear and tear and strain cables over time. BUT i always…
magnets 20x6x2mm (4pcs) 1,75mm filament Print instructions Remove integrated support then glue it. Use piece of filament for hinges.
Multifuncional case This case design is inspired by Prusa style and motto: Everyone is a maker, only I am a printer PRUSA It fit self-rolled cigarettes, to fit regular size cigarettes you can just scale it to 114% in every direction. The…
joint case with cap instolled print in place. cap fixed to main body in 1 file with no supports. Satisfying feeling with opening and closing the cap. recomend printing with brim, after cap is finished is possible to crank up the speed as…
A modification of my original model. This one is enlarged to 80 mm height to the size of a banknote. If your Christmas presents also include money you can hide it here and hang it on the tree. Of course you don't have to print the bottom…
Whether you've got flexible filament or not, these cases make for an easy print and a sweet looking phone. I designed these cases to print without support, so they turn out very clean. Both versions also provide a buffer for the screen…
Sedí na 0,96" OLED display s velikostí základní destičky 27x28mm (některé display se liší, například mám dvou barevný s velikostí 27x26)
Print Instructions Use the included 3mf file for the best result. If you wish to slice the model yourself, follow the instructions below. Orient the model as shown. Be sure to match the orientation of the Nintendo Switch logo. Layer…
Edit 9/25/2023: Per the comments, I have revised the micro SD slot to not be so tight, but snug enough to hold the sd card. Additionally, the slot will now only allow the micro SD card to go into it half-way, making it easier to pull out.…
A protective case for Lenovo legion go tablet; All the protective cases available so far did not support controller separation, so I made my own. it also has slot for perpendicular USB-C adapter on top USB-C slot and kickstand. print with…
Vented Case, SnapTop... This case is built for a cooler CPU when active cooling is used... derived from the need to cool the Pi 4B, The case requires a fan for significant cooling. This case will not cool the sbc by itself, but the…
The TerraPi EVO is a dual SSD case for the Raspberry Pi, that uses the 2.5″ sata SSD drives as the case, placing the Pi board between the disks. It comes only in dual SSD drive configuration. It utilizes the USB 3.0 port to connect a…
I created a Ear Plugs Easy Case for everyone, who need case for Your noise canceling plugs :-) It is very simple and very practical. Is for everyone, who need protect Your ears agains noise :-) This model I created entirely by myself and…
Samsung Galaxy Watch 4 - Body Case - 44 mm
Any feedback would be greatly appreciated . NOTE: Could try printing the case with ZERO top and bottom layers, perimeters: 8-10, honeycomb infill at 5-15%. Supports everywhere, style: grid, top Z distance: 0.25mm(for 0.2mm layer), top…
These two cases fit a Gopro Session action camera. The split design allows you to more securely clamp the camera in position, using the Gopro mount as the clamping mechanism. Both designs tightly fit the camera. Holes for the microphone…
Update 2024-07 : I added some variations of the model with slightly wider tolerances as for some people the default version was too tight. The notch that holds the joycon is 0.1/0.2 mm thinner in these versions. I also added a file with…
Hello there this is a simple case for the popular cheap DC-DC converter modules (LM2596(S)). Route the cables through the case bottom before you solder them to the DC-DC converter. Easily resized and customized in Fusion360 with the…
I made this quick and easy USB Case to use and remix it into way more interresting Cases. I used this USB Sticks from Amazon because it is a widespread model and easy to take apart. I look forward to see your remixes and will add some…
My first remix design for a 3D print! I added the hooks to the case such that it can be screwless mounted to the horizontal profiles at the bottom of the prusa MK3s printer. RPi4B case:…
This remix allows the use of sensors I purchased off Amazon (HiLetgo) that had a different style of connector from the sensor the original case was designed for.
A half-shell case for the Galaxy Tab S6 Lite. Covers the back, sides, and corners. Also provides a bezel to protect screen when device is face-down on a surface. Hard shell design: Fills-up the MK3S build space (1-2mm to spare) Prints…
Modification of Deburring Tool Case 154mm (Libraton) - Rugged Box Style to fit NB1100 deburring tool. In this remix you can find part to fit NB1100 deburring tool to fit to original box made by user @Shadow_1242354 . You just need to…
A retro case that's simple and functional. Designed for use with pi's active cooler. I was aiming for a retro, Art Deco vibe, and also tried to capture the classic look of an RTX or Radeon reference GPU. Print Instructions: Settings: ~38g…
Mouth Guard Print In Place. For those who want a new case with a hinge to hold your mouth guards. I made this in PLA.
Please hit LIKE on my design if you download it so I get credit, thanks! This is a counter top enclosure designed to hold a 1602 LCD display run by an ESP-32 processor. There is also a spot for a LoRa transceiver. Fits these parts: ESP32:…
I have designed this box for condoms, tampons and stuff which is almost perfect: https://www.printables.com/cs/model/371842-smooth-pocket-case-for-condoms-durex-tampons-etc The only downside is that you have to trim the corners of condom…
3D printed 2.5" HDD Enclosure A simple 3D printed case for an old 2.5" HDD. The case is designed such that, for the most part, it is a push-fit, with four nuts at the bottom, mounting the drive to the plastic case. Equipment List 4 x…
A slim case for the Raspberry Pi Zero (w) and the Pi Zero 2 with mounting tabs and a friction fit lid. There are a few alternate lid designs if you want room for a header and/or heatsink. The regular case and lid work fine on the Zero 2,…
A nice case for your 7" Raspberry Pi Touch Display 2 (https://www.raspberrypi.com/products/touch-display-2/ ) and a Raspberry Pi. Features easy access to the USB and Ethernet ports. Designed to use the M2.5 x 6mm screws included with the…
This is a mashup of two very cool systems. Additional Materials: 6 pcs - M3 x 6 mm bolts (or M3 x 4mm) 6 pcs - M3 x 8 mm bolts 14 pcs - 3 mm x 35 mm rod 2 pcs - 3 mm x 32 mm rod (for the bottom of the front latches 2 pcs - 3 mm x 25 mm rod
This is business card case and holder. Printing is easy because of the print-in-place model If opened at the suitable angle, it becomes a showcase. It works with most business cards from all around the world. Inner size is about 53mm x…
Assembly list of non-printed items for pencil case 4 pcs - metal axis 26mm x 3mm If you looking for a version with a pencil sharpener
Simple case for the arduino nano for your projects, protects the board and offers access to the usb and exit for the cables. For micro usb and USB-C models. Updated (10/07/2022) added case for USB-C arduinos Using 3x10mm screws. Print…
a minimal case for a HC-SR04 sensor, fits without screwing.
This is a fast and easy to print case for a RPi 4. The cover simply snaps-in making it simple to access the board. It is compatible with all versions of Raspberry Pi 4. If desired, you can add : 4 screws (M2.5 x 5) to secure the board.…
Spare plug. Ready to ride. A spare spark plug belongs in your toolkit — this M14 Spark Plug Box for Vespa gives it a dedicated place. The two-piece printed case encloses the plug for storage and transport, with a screw-top closure and…
Holds 4 rechargeable AA Batteries. Place batteries nub up for the “Charged” indication and nub down for the “Depleted” indication. I have tested it with the following rechargeable AAA battery brands: Amazon Basics AA High-Capacity -…
Designed for Prusa MINI/MINI+ Main features Easy to attach and detach from 30x30 aluminum extrusion of the MINI's z axis, no screws are necessary! Easy access to the Pi's SD card, no more disassembly required! In case you are also using a…
A Fun and easy to print hard case remote for your Chromecast with Google TV. Designed for 0.2mm layer heights and prints with no supports. Does a great job preventing accidental volume changes!
This is a very compact but sturdy case for the DJI Mini 3 Drone. I created this, so it does use up minimal space in my backpack while still providing sufficient protection to the drone. The lid snaps safely on the enclosure, there are…
NanoMesh Mini is a compact case design for the Jetson Nano Developer Kit. This case be used entirely tool-less, although it can be secured with four case screws. The carrier board is held in place with stand-off pins. To secure the case…
Print both the lid and the body. The ESP32-C6-DEVKIT-M-1 can be pressed in and should be held in by friction. The tolerances are designed for this purpose. I printed it on my Ender 3 with Prusament PLA Galaxy Black and 0.2mm Layer Height…
Improved Version Available: AirTag Keychain Holder V2 V2 offers improved fitment and optimized printing profiles! This is a very simple key ring adapter for AirTag. I didn't want to pay for crazy expensive cases just so I could hook my…
![Jumbo Weekly Pill Case [Remix]](https://media.printables.com/media/prints/457526/images/3763604_7e3dee36-5def-4e0d-8ab6-ebd5a55b8b77/img_1569.jpg)
![Business Card Case Holder & Stand [& Credit Card too!] (print-in-place, no support)](https://media.printables.com/media/prints/846c1284-c782-4628-b4ad-1f2f17dfd173/images/11630392_08724ebf-b08e-42b6-a261-58a1bf8a7450_f93918e8-9f3f-411a-b996-adeb883684e5/version-2.jpg)
