Counting matching models…
NB: V2.1 has been updated to use proper threaded thumbscrews. Note that V2 had a problem with the thread direction so has been fixed with this latest update. I wanted a way to mount my Honeycomb Alpha and Bravo flight controls under my…
Should print fairly similar to the original design, I found my best results though at 0.16 layer height and printing the parts at an angle of XYZ 90, 45, 45. I think 0.2 layer height would work fine as well. Using the auto-orient feature…
These hand grips/handles were made 1:1 with measurements taken from the official Boeing 737-800 specs. Instructions: Unscrew the existing small handle from the 2 engine honeycomb bravo airliner handles Pull the small finger grip off Push…
JONNY BRAVO figures Hey mama! Bring some classic cartoon attitude to your collection with this Johnny Bravo inspired 3D printable figure 💪😎 This model is designed as a multi-part snap-fit build , so you can easily print each color…
I created this model to mount my Winwing FCU to my Honeycomb Bravo throttle. It keeps the FCU rigid and has a 15 degree upward tilt to make it easier to view. Print settings: 0.2mm Layer Height 20% infill 3 walls Print mount on its side,…
I have designed this model to mount my Octavi IFR-1 “Autopilot Controller” atop my yoke. This way, I have it right in front of my eyes instead of somewhere on the desk where it is not as easy to use. A very simple model, printed in basic…
This is a custom grip for a Rossi Rio Bravo .22lr lever action rifle. The only extra hardware you need is a shorter bolt that holds the grip to the frame. Just reuse the original washers from the stock furniture. I even included a spot…
Here are some mounts that can be used to hang your Honeycomb Alpha Yoke and Bravo Throttle on a wall (or in my case the back of a door). I used two 4x35mm screws to fix each base. Print two plugs for each mount to fill the screw holes.…
PCIE SSD mount for the MSI Bravo 15 C7V
The compressor (e.g. Ryobi One+ P731) adapter for the Bravo (ver 4, used by many isup manufacture e.g. Jobe) hand pump tube. A thick isup board takes a quite long to fill up with the hand pump even with reasonable two function pump. The…
This is a part I designed for the Ryobi P747 dual inflator. It enables you to use the tube for a Bravo branded hand pump (Tends to come with a lot of inflatable kayaks and SUP boards). This is only for the low pressure/high volume side of…
This is a remix of eclair4151's trim wheel cover . I wanted one that didn't have any 90 degree overhangs on the knobby bits, and had a nice rounded feel on both sides. I also added a slight radius on the inside and a bit of a lip that…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Quick and dirty mount solution You can use rubber pads to prevent movements on slippery desk surfaces
This is a small bracket or stand that attaches to your Honeycomb or Logitech mount, allowing you to prop up your Stream Deck, Octavi IFR1, or any other device. This design enables you to use your devices while flying without the need to…
I have a cockpit, but no where to really use my mouse that is stable, thus using the mounting screws on the top of my bravo, I made this print. I opted to double stick tape a rigid mouse pad on top of this, since i had it, but it should…
Introduction I am new to the flight simulation hobby, 3D printing, and CAD design, so please be patient with me. I decided to create my own throttle quadrant to enhance my immersive experience. This is intended for flight simulation…
This is a buttstock extension that can be added as a spacer between the buttstock of the KRG Chassis and its KRG Recoil Rad, to adjust the length of pull. According to KRG website , all KRG chassis use the same recoil pad, but keep in…
Ever wanted to use realistically modelled PA-28 controls for your Honeycomb Bravo Throttle Quadrant? Or maybe you want well made controls with larger and more comfortable knobs than the stock GA ones? Perhaps you often fly in VR and find…
Model kołpaka do felgii fiata bravo. Update 13.03.24: Dodano plik do druku oraz zmodyfikowane model(Fiat_bravo_capsV2). Model wydrukowany na Bambu Lab X1E.
Original credit to the original design of Ross Barlow from www.flapmodster.com and the post of belinconu in https://www.thingiverse.com/thing:4916198, which was the files that i'ved used, this is a remix of the flaps detents for Honeycomb…
I've modified this excellent model for increased stability and magnet support for the “thumbscrews” - the brackets are the same size, so if you already have them printed and screwed on they'll be fine, but this version has a slot for…
I've split the model up into various parts, in case you'd like to try printing it in colour. Tip: The tab on the bottom is designed for using something such as Sticky Tack (a reusable soft adhesive putty), to keep your artwork secure in…
Simple holder to mount the Realsimgear GFC500 under a Honeycomb Bravo Throttle with double-sided tape
English-Version: Hello everyone, After countless iterations and calculations, I present to you the BRAVO Panel (Broadband Resonance Absorption & Vibration Optimizer) – a fully 3D-printed, modular acoustic panel designed to achieve maximum…
I wanted a way to mount my Honeycomb Alpha and Bravo flight controls under my desk, but every mount I found online was too big. So, I decided to design my own. But when i printed my old model for a friend of mine he could not mount it. I…
The light switch on my Piaggio Super Bravo shattered (the plastic probably got brittle after 30 years of use and UV exposure). This design should be compatible with most of the old Piaggio mopeds since they reused many parts betwenn…
All models are marked by myself. My first model. Hope you like it. Send me some feedback or some advices to improve printing.
I wanted one that looks like the one sold by Honeycomb but didn't see it for sale locally so I made this. It is printed in TPU and looks pretty good; adding a filled side like the silicon-molded version would have added a lot to the print…
Σύνδεση καπακιού ρεζερβουάρ για FIAT BRAVO 2. Υπάρχει λίμα σε 2 μεγέθη. Υλικό TPU. Και τα δύο ταιριάζουν, στις φωτογραφίες είναι το μικρό. Το χρησιμοποίησα αυτό και είναι τέλειο. . Μπορείτε να χρησιμοποιήσετε ό,τι σας βολεύει.
Airpump adapter replacement for Bravo 4 Hose inside diameter: 17 mm / ~0.67 inch Attachment outside diameter: 21 mm / ~0.83 inch Try the fit before you glue it into the hose, maybe there's no glue needed. Print it upside down. (cutouts on…
Simple model to increase the LOP of your KRG Bravo. Fusion360 model included so feel free to adjust the height. Don't forget to get some longer screws!
Tappo faro anabbagliante per Fiat Bravo 2 da stampare in TPU
Small molds for adding weight to a KRG Bravo stock in the buttstock area. There are different items. One goes in the under either the flat cover, or the Hook style cover that is on the bottom of the stock and accessed by a single screw.…
This is model is designed to be printed with a Bambu Lab AMS or similar. I recommend printing with a .2mm nozzle at .14mm layer height. The best sheet magnets I have found to use with this model is Marietta Magnetics brand 30mil (with…
I wanted a way to mount my Honeycomb Alpha and Bravo flight controls under my desk, but every mount I found online was too big. So, I decided to design my own. But when i printed my old model for a friend of mine he could not mount it. I…
Small mold to use for making a weight for a KRG Bravo stock. Goes in the pistol grip void. Print and fill with whatever weighted material you like, and you have a little weight plug to go in the hollow pistol grip. The beauty is that is…
If you like my models and feel inclined, I could always use more filament for test prints. https://ko-fi.com/plaid_brad The KRG Bravo rifle chassis has an adjustable cheek piece, but there are no index marks or detents like on other…
A tray with a removable hex grid for the ice/water dispenser of newer LG refrigerators with the "Bravo" style ice/water dispenser. Use Ironing for a smoother surface. Suggest using a "metallic" filament , otherwise it just doesn't fit…
Circle printed flat witch supports, infill 80% but i think 50% should be enough. B printed from composite x on elegoo mars but should be possible print also on FDM printer. Finishing works - sanding, spray putty, sanding again, varnishing…
Made a remix of 2 different stream deck holders for the Honeycomb Bravo flight sim, noticed that there wasn't any mounts for the stream deck plus so had to mix and match some. https://www.thingiverse.com/thing:4730037 +…
English-Version: Hello everyone, After countless iterations and calculations, I present to you the BRAVO Panel (Broadband Resonance Absorption & Vibration Optimizer) – a fully 3D-printed, modular acoustic panel designed to achieve maximum…
A few additional parts i made for the “Castle Bravo” by @Camshafty_2388580 LED Diffuser: These simple cylinders were easily designed in Fusion 360. For optimal results, print them with a 0.16mm layer height using white or translucent…
A bold Johnny Bravo-inspired figurine made in a detailed 3D printed style, featuring the iconic oversized pompadour, sunglasses, fitted black shirt, and exaggerated muscular pose. This playful collectible brings strong retro cartoon…
If I had the wall space I would use bowerandy's Honeycomb Alpha/Bravo Wall Mount - but I don't. I need to put my throttle on the shelf, and while reading reviews I saw two people who complained that the trim wheel had broken off. Makes…
Honeycomb Bravo Handle Holder for the Ikea Skadis System → Mount your Spare Throttle Levers on a Ikea Skadis Wall for easy, clean Storage → Designed to be printed in one Piece or split up to facilitate small printers → Does not wear out…
I scale it a little bit to fit my IWB holster by Bravo Concealment. Original is from Ben Anderson from Thingiverse.
Picatinny tippmann bravo one handguard, the holes on the side are mloks. Theoretically should not need supports, the picatinnys are connected by m5s, the nuts are put on the slots on the side of the guard.
Ersatzwürfel für das Kinder Brettspiel “Bravo Traube”. Packe noch die Fusion Datei dabei. Falls jemand veränderunge vornehmen möchte, wie z.B. wie beim Original das Bild der Traube anstelle dem Text. Habe ihn ohne Stütze und 10% Infill…
The popular Honeycomb Bravo features a dome-type body, which means there is no space on top to place and use a mouse, keyboard or other controller. This print creates a flat surface which mounts to your Bravo so you can do just that.…
English Version Hello everyone, After the first version and further feedback from the community, I am presenting the BRAVO-Panel V2 (Broadband Resonance Absorption & Vibration Optimizer) to you today. The goal remains the same: a fully…
1.9 rc beaclock wheel designed for use with 12 mm hex like Axial SCX10 rings for the beadlock can be found here https://www.printables.com/model/744137-bead-lock-ring-for-axial-scx10
This is a holder for the Smok Priv N19 Vape for a Fiat Bravo 2008 car. It fits either next to, or in place of the cylinder ashtray that sits next to the cars handbrake/e-brake.
Montage Seal Tool For Piaggio Moped Engines (flywheel side) The engine gasket sealant installation tool for Piaggio Ciao is a valuable tool designed to facilitate the installation of engine gaskets with consistent pressure distribution.…
V sušičce ovoce se nám rozbila vrtulka větráku. Tak jsme si novou vrtulku vymodelovali v CAD programu a vytiskli na tiskárně Prusa Mini. Po vytištění se na vrtulku nasadilo stahovací perko (z původní vrtulky) a vrtulku jsme nasadili na…
Print 50% infill, mouse ear, no support,
I wanted to use RAM mounts with my Honeycomb Alpha and Bravo units to mount my keyboard, GPS, or other accessories, and the standard ball mount had the wrong hole spacing. Drew one up in CAD with the 40mm spacing needed. Printed in PETG…
A screw-on, magnetic case for storing and carrying the CMMG Bravo conversion.
Printed on Flashforge A5M using standard PLA. 0.2mm layer height 0.4mm nozzle Tree (auto) support for knob 5 wall loops (2 mm) 15% Cross Hatch infill density 5 bottom shell layers 5 top shell layer Default Flashforge Generic PLA settings…
Passend für: Tippmann Bravo One Category: Other
Printed on Flashforge A5M using standard PLA Print lever with open slot on bed Print handle with larger face on bed Switches: https://www.amazon.com/dp/B083JWJPW5?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_3&th=1 Pogo Pins:…
English-Version: Hello everyone, After countless iterations and calculations, I present to you the BRAVO Panel (Broadband Resonance Absorption & Vibration Optimizer) – a fully 3D-printed, modular acoustic panel designed to achieve maximum…
This is a picatinny rail hand guard for the Tippmann Bravo One paintball marker. Here are two models, one complete and one cuted Version for smaller printers. The pictures are of the cuted version. This V1 is an simple symetric version.…
The size can be reduced on one side depending on the condition of your parking brake cables.
Propreller cap for Aquabot Viva or Bravo. I design this part as replacement of my broken cap. Is the first summer with this design, probably I need to change some details. Print Settings Rafts: No Supports: No Resolution: 0.2 or 0.3…
This is a picatinny rail hand guard for the Tippmann Bravo One paintball marker. This is cuted for smaller printers. V2 is a improved version with adjusted highs of the rails to fit to the marker. You can find V1 here .
Usually the Honeycomb Bravo quadrant is placed to the right of the yoke. This model let's you mount the FlightSimBuilder GNS530/GNS430 at an angle to properly see the screen. I included 2 models for you to choose. The difference is how…
Passend für Tippmann Bravo One Tippmann Magazin 12x: https://www.amazon.de/gp/product/B07DPC74F7/ref=ppx\_yo\_dt\_b\_asin\_title\_o05\_s00?ie=UTF8&psc=1 Einpressmuttern:…
The stock gear lever on the Bravo Throttle Quadrant is a bit flimsy to me. So I made an outer cover and a "rim" to fill the hole (you will need two of those). For printing it I've chosen TPU, all parts fit without glue.
The levers that came with the Throttle Quadrant were a bit fiddy. So I made some covers that fit on the black original levers (see picture). As I mainly fly single or twin engine aircraft, this is perfect for me and gives me a lot more…
This is a bracket designed to attach some 200-lumen flashlights I picked up at Costco in a three pack for $15 some time ago. Any flashlight with a diameter of ~28mm (1 1/8") should work fine. The rectangular slots on the sides are for two…
Náhrada za ulomenou páčku motůčka BRAVO. Páčka se nasadí ná část odlomeného dílu a zajistí dvěma vruty 3 mm, tištěno z ABS, 40 o/o výplň, 0,2 mm, tryska 0,4 mm
Use project cut your gaskets an ride
MAN, I'm pretty! This is Johnny Bravo. His arms move in opposing directions so he can even do the monkey dance! The 3mf has the parts organized by color. I've also added a hand mirror to place in his left hand, if you'd like (he'd…
This offers a sleek, custom-designed hubcap-style cover specifically tailored for the Chicco Bravo stroller. It seamlessly integrates a discreet and secure compartment to house an Apple AirTag, ensuring you can effortlessly track your…
💖 Support Me If you like this model and want to use it for commercial purposes, you can support me on Patreon and get a commercial license: https://www.patreon.com/cw/MonsieurPierre A detailed 3D model inspired by Johnny Bravo, the iconic…
Printed on Flashforge A5M using standard PLA. 0.2mm layer height 0.4mm nozzle 5 wall loops (2 mm) 15% Cross Hatch infill density 5 bottom shell layers 5 top shell layer Default Flashforge Generic PLA settings for everything else. Requires…
This will securely hold a Boston Acoustics Bravo speaker in a vertical configuration. Perfect for placing surround speakers on shelfs or other surfaces. Straight-forward print, no need for supports. I forget how much infill I used,…
Two part bracket to attach the Miniflight MiniFCU and MiniEFIS to the Honeycomb Bravo. You'll require: Two M3x25 bolts and nuts, to attach the two parts. Four M4x8 to attach the bracket to the Miniflight parts Also Added a Second Support…
The thread is meant to screw in the air hose with the product. Print instructions: Print canted 45° to strenthen the part. Try the STL with inbuilt support. I also suggest using a 5mm brim with 0mm separation gap to stabilize the print.…
Here's a quick BCM logo I threw together. It prints with default profiles and you can adjust the size, infill, etc to your personal liking.
Soporte para sacar el cambio de la moto ebroh bravo gle del puño y ponerlo en el manillar, ser recomienda imprimirlo en ASA para que aguante la intemperie, el modelo de prueba se hizo en PLA y ha aguantado un año sin problema La pieza…
Štít pro ETA Gratussino BRAVO 2 Proti odletování kousků při krouhání Shield for ETA Gratussino BRAVO 2 Prevents flying pieces when cutting Recommended material PETG
Kryt strouhače na výrobu strouhanky. Již nebude strouhanka lítat všude, ale pouze do Vámi připravené misky. Na MK4 lze tisknout najednou, na MK3 se musí rozříznout a poté slepit. Tisk bez podpěr.
Supporto/Blocco/Fermo per sistemi di simulatori di volo Honeycomb Alpha e Honeycomb Bravo. Si avvitano al piano di supporto (scrivania o altro) e consentono di fissare il gruppo del volantino e/o quello delle manette in modo semplice ed…
Can be printed using any material. Model is a bit small (not flush along sides) if you use ASA. I would recommend using ~105% size. Used for the underside of the flap toggle for the Bravo Throttle Quadrant
hope you like it Category: Art
The Nuwave Bravo Pro is an excellent low-temperature drier for filament, reusable desiccant, and other misc. purposes, but it lacks low-cost ventilation options given the extreme temperature reached by the oven enclosure. This model is an…
A set of 3D printed throttle handles for the Honeycomb Bravo Throttle Quadrant. The original Honeycomb handles are relatively small, and this replacement set has a much more realistic scale. Make those Microsoft Flight Simulator, X-Plane…
This throttle lever is designed to replicate the look and feel of the Tecnam P-Mentor power lever, perfectly adapted for the Honeycomb Bravo Throttle Quadrant . It provides a more realistic flight control experience , enhancing ergonomics…
Supporto/Blocco/Fermo per sistemi di simulatori di volo Honeycomb Alpha e Honeycomb Bravo. Si avvitano al piano di supporto (scrivania o altro) e consentono di fissare il gruppo del volantino e/o quello delle manette in modo semplice ed…
A bold Johnny Bravo-inspired figurine made in a detailed 3D printed style, featuring the iconic oversized pompadour, sunglasses, fitted black shirt, and exaggerated muscular pose. This playful collectible brings strong retro cartoon…
This is a small bracket or stand that attaches to your Honeycomb or Logitech mount, allowing you to prop up your Stream Deck, Octavi IFR1, or any other device. This design enables you to use your devices while flying without the need to…
