131 models
This is a simple box to put a communication board of the JK-BMS inverter BMS (model JK-PB2A16S20P) that I use in my DIY solar energy storage system. Letters on the box could be filled by the nail polish or sealant to make letters stand…
You need 4 90/92mm fans. Print the two parts and glue them together. The duct is mounted with 2 screws on each side. For the fans you need m3 screws. On the back are holes for zipties. Post a make :)
Housing for Interfaceboard
I made this model in Fusion 360 based of my JK-PB2A16S15P, thought it could come in handy for someone designing an enclousure or mount. Both BMS and Comms board included. Please go easy on me, I taught myself.
The cooler prints in two parts that is glued together. The three "sticks" that is printed with part 1 is used to strengthen the join. Glue them on the inside over the the join. There is a holder for the HW-585 12V fan controller You will…
A starter for the urgent desires. So, com board is ready and was done with M3 heat inserts in mind. As there is currently no idea of where it would commonly fit this is not the final solution. I for my part will fit it into a gridfinity…
The parametric Autodesk Fusion file can be modified to fit your exact fan size. Excluding the air blocker plate, the model prints in four different pieces. STL files and hardware: Fit 80x80 mm and 120x120 mm fans. To mount the fans four…
I have created a support for three 92x92x38 mm fans for a Deye 6kW inverter. In summer, the heat increases the temperature, so it is used with a PWM controller that can be purchased on AliExpress, along with the fans and other components.…
Standfuss für das Anschlusspanel des JK Inverter BMS incl. der Starttaste
Simple bracket for the JK Inverter BMS. Is required twice to attach the BMS at each end to a wall or to the battery hou
Hello, this is a simple compliant mechanism designed to invert a linear motion. If you push (or pull) on one side the other side moves into the the opposite direction. It's still in a very early stage and the range of motion is quite…
Jednoduché a nenáročné řešení chlazení střídače Solax X3 hybrid G4, které za pomoci tří ventilátorů a termostatu W1209 umožní vyšší průtok vzduchu přes žebra střídače. Držák rámu je upevněn za neosazené průchodky CAN1/2 a DRM/OFF. Na…
It's unlawful to waste a drop of sriracha, yet that cap makes it so hard to prop up your bottle to get every last drop. This stand allows you to invert your bottle in your fridge or countertop, assuring you still have more sauce at hand.…
This is a 3D printed inverter mod centered around integrating a 1,000 watt pure sign wave inverter into the gen-1 Chevy Volt and does so through a custom rear hatch faceplate that adds an interface for you to remotely wire-up a hidden…
A remix of BeardedJester's almost perfect painting grips that allow the inverter handle to be attached to the regular size grip. I invert models while painting too frequently to be bothered unscrewing the bottle cap and moving my model…
With this model you can mount your jk inverter bms on any flat surface with screws. To mount this holder to bms you need 6pcs m3 nuts, 6 pcs m3*35mm srcews.
Case for the components of a Ahoy DTU. See the Ahoy DTU Project Page on Github: https://github.com/lumapu/ahoy The Ahoy DTU allows for communicating with a bunch of Hoymiles Microinverters for small sized Solar Systems. It is even…
Spacer for mounting a Hoymiles Inverter on the wall. This was designed with the dimensions of the HMS-1600-4T model, but may fit on other models as well. There are two variants: One which resembles the slots on the inverter. One with two…
Finally I decided to design a GoPro mount adapter that inverts the mounting order. Print Settings Rafts: Yes Supports: Yes Resolution: 0.4x0.2 Infill: 15% Please note this is a work in progress, you may encounter problems with some slicer.
It is a universal ventilation system for all inverters that need additional cooling or you just want to make its life longer and lower its temperature. The individual fans can be infinitely connected together to create whatever width you…
A set of MMS Inverters for your MMS/Picatinny use! If you need to mount male to male, or female to female, you've got options here! - MMS Short Female to Female Inverter - MMS Long Female to Female Inverter - MMS Short Male to Male…
This is a wall mount to store an EGO power inverter. Designed for the PAD1500 but should work with any EGO battery compatible inverter. Designed to print standing vertically so the "teardrop" holes have the point at the top. Update…
Spacer Plate for Hoymiles (HMS 800W-2T) to mount on flat surfaces. One model with the name “Capri-Sun” on top - because i think its funny. One model without name tag
Added some new photos of black print with added switch to turn on and off inverter Remixed dyslexicEnginers great battery mount to connect a 20 volt porter cable battery to an Everstart 70000M 12 volt power inverter. The size of the…
Some people got together to hack the communication protocol of a popular micro inverter by hoymiles so that you can see the internal values and send them on via MQTT. You can find the conversation here (in German) and the code here . I…
📄 Fan bracket for Hoymiles HMS1600-4T micro inverter ✅ Compatibility This clip-on bracket is designed for the Hoymiles HMS1600-4T microinverter and potentially other HMS/HMT models . The inner width of the slot (fit over the cooling fins)…
Fixed holes, addes labels for original.
Replacement knob for the Harbor Freight 2000w invertor generator. Might work with other models, but I haven't tried. Print settings: .4mm or .6mm nozzle 4 walls or more 30% gyroid infill or more Material can be whatever you think will…
A wall mount for your EGO brand 120V inverter! Mounting with 1" drywall screws (or similar). Print standing-up. No supports necessary. Please post a "Make" if you print one! This is reupload of kMechie's great design. I have included a…
This is a Lego Duplo compatible piece to connect two bricks bottom to bottom. Also fits Hubelino marble track pieces to mount them upside down. Variants: 2 by 2 piece 2 by 1 piece — A brim can help with bed adhesion, compensating for the…
An update has been made. One dimension has been corrected and a variant with left-hand control has been created. For right-hand control, parts A-B-C-D are printed. For left-hand control, parts E-B-C-F are printed. For more information,…
modified to print without support Print Settings Printer: DIY Build Rafts: Doesn't Matter Supports: Doesn't Matter Category: Kitchen & Dining
Surprised there wasn't a powerpack on Thingiverse. So i mocked up a simple one. With main unit, inverter and baseplate Its a full scale STL (ie 2m tall!). For OO scale to 1.3%, and for HO 1.15% Printed using prusa slicer with a colour…
Reduces the inverter temperature and prevents the buit-in (and noizy) cooling system from activation. No additional mounting required. No supports required. Hardware: 4 pics 92x92x25 fans (e.g., NF-B9 redux-1600 PWM ) 4 pics M5*12 bolts 4…
Spacer for mounting a Hoymiles Inverter on the wall. This was designed with the dimensions of the HM-1200 model, but may fit on other models as well. There are two variants: One which resembles the slots on the inverter. One with two…
I wanted a compact way to (safely) house three breakers going to my MPPT Solar Charge Controller so I designed an enclosure for them. The breakers were purchased here . Lid and print photos will be added in the future. Currently working…
HEP inverter cabinet found on the Alaska RR SD70MAC-HEP - dual-service passenger/freight locomotives.
Ryobi makes several AC Inverters and USB chargers. The 40V battery RYi300BG is nice because it has a 300W Pure Sine wave inverter, a USB Type C port 5/9/12/20 VDC rated at 2A, and a USB type A port rated at 3A. Unfortunately it doesn't…
Holder to current transformers from DEYE hybrid inverters. Кріплення до трансформаторів тока від гібрідних інверторів Дея. Бо дуже незручно без кріпленя, бовтається як каз на що.
Adapter for inverting the mount and turn the Camera 90° towards holder Print in PETG or ABS to achieve better strength (if the camera should be mounted on a bike or similar)
A simple fan shroud designed for use with a Sunsynk 5k Inverter. Bottom-up airflow supporting 2x 92mm fans (AC or DC). Holes support 6mm threads. Includes 2x braces to support the joining of two halves. Required: Drilling 2x holes into…
This is the remote control wall mount for LG air conditioner with dual inverter technology. Please see the images to verify that your ac has the same remote. There are two versions. The difference is in the location of the screw holes.…
This is a simple print with no supports. I like it with PETG — Food safe and structural, but I can also accept that it shouldn't matter. I did this with OpenSCAD. It's a simple model. Source included. You can modify it yourself. Two…
Front and back parts glued to the bottom. Cover fixed by TEX. Fan 40mm. Created in Solidworks for makers. Feel free to use it or modify.
material PETG, no supports when prompted by the printer, insert 4 pieces of M3 nuts into the hexagonal holes
Renogy Inverter Mount 2kW 6 holes for screws allowing strong mount even if the screws are short. The two versions where one is more open in the top area (compact). The two types can be combined. Choose type based on the space available…
This part is a cable box for a Huanyang Inverter. I made it for my 2,2 KW/220V Inverter but it may also fit for other Versions. To finish you also need the following parts 7x screw M3 x 10 (lens head) 3x nut M3 2x cable fitting PG9 There…
I made a scale model print of my solar shed design. The scale model serves a useful purpose in planning the layout of my inverters, panels, batteries, and bus wiring. Model can easily be painted in Bambu Studio for multicolor printing as…
This tool is used to release the connector for the RS485 (MODBUS) port on the FOXESS Invertors. I have included the step file in case anyone wants to tweak the design but it seems to work as it is. Print Settings Printer Brand:…
we got a new A/C unit, and it was so low-cost and had no remote mount for the wall 10 Min in FreeCad and 25Min on Magneto X and we all set
Versions With supports: The “skirt” and added layer above that covering the 6mm hole enable a print without further support. If the perimeters are printed from the inside out, the O-Ring groove can be printed without supports as well.…
Versions Blank: If you don't want to use the port, you can put in the blank plug to seal it off. M16: For small diameter cables as in the original application this gland is sufficient. Currently all versions are universal, so you can plug…
Cooling system with 3 x 60x15 mm fans and W1209 thermostat with sensor. It allows you to reduce the inverter temperature by approximately 10 degrees Celsius. Mounted with 2 screws to the wall, does not interfere with the existing…
Print “BMS plate top thingy” twice. I shoved looped tape underneath the bottom feet to hold them. Check collections for other files.
I needed a stand for four 80mm fans and couldn't find one, so I edited it to accommodate two fans, allowing them to be placed side-by-side in pairs, and enabling printing on the table without space issues. My inverter is a Growatt, but it…
Used to mount a 'BESTEK 300W Power Inverter DC 12V to 110V AC Car Inverter' to car interior..
To mount this, you'll need M4 threaded inserts pressed into the 2 holes which hold the datalogger into place. The hole diameter for the wall mount screws is ∅6mm.
This is a wall mount for the Bauer (Harbor Freight Brand) power inverter. Its a simple design that absolutely is not perfect but it works great for what it is. Feel free to remix as needed. This is just what I could throw together quickly…
I found some similar devices here, but did not fit My kind of Chilli, so I designed one. This device used to help to extract the last drops of Your favourite Chilli, to save environment and help World peace… :) There are two versions:…
Ich habe für den Deye Wechselrichter einen Adapter für die Kabeleinführung für die Kabel von den CT Klemmen entworfen. Passend für das EN25 Flex Rohr
This is a modified model to update it to the more recent version of the Renogy controller to install it over head. Installed pics are from a 1983 Vanagon Camper I installed the inverter into. This is over the kitchenette so there is…
Printed at .2mm layer height with tree supports for the attachment tabs
Renoget 1000w/2000w/3000w pure sine wave inverter terminal cover 90 deg left and right
I designed this to suit an 8kw Deye hybrid inverter I am mounting inside an insulated battery bunker. It attaches to the top of the inverter with 10mm wide double-sided tape. It should suit 5/6/8/10/12kW models as they are the same size…
Giandel Inverter Remote case Requires: 4 - M3 x 10 screws. 4 - M3 Threaded Inserts. 2/4 - M3 wood screws.
This sleeve is meant to help keep the Ryobi Inverter Adapter (RYi120AVNM) attached to the battery stem. It's sized to be a snug fit on both the adapter and battery, but I've found the battery stems have non-insignificant size variance…
This setup features a custom cooling solution for the GoodWe inverter , designed to maintain optimal operating temperatures. It includes a W1401 thermostat to regulate the cooling process and two high-performance fans mounted on a…
Simple little wall mount for EGO inverters. Works with the 150W Nexus Escape inverter but should also fit the 400W variant. Can be printed using PETG/ABS and mounted using four countersunk wood screws.
The SunGoldPower LFP inverter/charger series and Renogy battery monitor come with remote displas that are intended to be mounted recessed into a wall or panel. I'm installing mine on a camper and the walls are way too thin for a set of…
Created this model to mount a Victron Energy 12/500 120V inverter in place of the stock inverter.
This is a flip-up cover to protect the Sol-Ark 15K's LCD screen from direct sun. The cover slides into slots to hold it closed without flapping in the wind and to hold it open. It can be mounted with double-sided tape. Be sure to use tape…
Summary With the help of this stand, a Hoymiles 800W inverter can be positioned upright and at a slight angle. This reduces the space required and improves heat dissipation, especially in summer. Tool-free installation – no screws…
This is a holder for the Deye Inverter Allen Key for the front panel. I made the holder for the 2.5 mm Allen Key that came with the Deye Inverter. Just use double-sided tape to stick it wherever you want on the inverter not to lose it. I…
UPD: this is a bad design, 4 x 92mm straight fans work much better. Use this one Helps reduce the frequency of active cooling cycles during high-load periods. Useful when the inverter is installed in confined spaces or areas with poor air…
Sú tu 3 modely dokopy, je to prispôsobené na systém spiro Spiro 100 je vytvorený pre koleno ktoré si kúpite 55x110 / Ø100mm Spiro 100 A je pre koleno ktoré si vytlačíte, je o cca 1cm užší Spiro 100 B je koleno s rozmerom 46x110 / Ø100mm…
This is a simple holder for a roll-on antitranspirant (e.g. from Nivea). The holder allows to put the deodorant upside down to use the last drops when the container gets empty. Please consider a small contribution to my Paypal. It would…
This is a fun print that converts a tension spring or rubber band that applies force when in tension into something that applies a force when compressed. This works with springs, rubber bands, or whatever else you can fit into the hooks.…
All details in this video (in Ukrainian)
After the original injection mold part broke, I designed a new part for my Load UP 1000 inverter. As the part will stay cool from the passing air it can be printed in PLA, but I recommend something more durable like PETG/ASA.
Cooling for solar inverter Cooling for solar inverter. For use with 92mm radiators and STC-100 thermostat
Print in place, it is technically 2 parts, but I have a small breakable bridge joining them as one stl. From what I can tell the original cap uses something like a 14x3mm o-ring (I suppose you could borrow the one off the oem cap). I did…
Made to hold my shampoo/conditioner bottles upside down on the corner of my bathtub. Included holes for two suction cup mounts on the bottom for extra stability. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No…
I reused a DC-to-AC inverter enclosure to house my 1KW DC-to-AC inverter. To finish of the enclosure, I designed a custom front panel. The custom front panel hosts the unique combination of connections, meters and controls that my new…
The SunGoldPower LFP inverter/charger series comes with a remote display that is intended to be mounted recessed into a wall or panel. I'm installing mine on a camper and the walls are way too thin for a large recessed display like this.…
Inverts the Camera orientation for popular Sony307 square camera often used in vehicle on-board cameras. The commonly provided mounting bracket orients the camera to only point up into the sky away from the vehicle, or (flipping the…
I created the inverter/sound directional adapters (not really sure what to call it) to improve the sound quality when having my HP P34hc G4 monitor standing in an open area without a wall behind. Can be attached with glue our double-sided…
For the Champion Dual Fuel Inverter Generator I found myself searching for some tools every time I would start it. These where a screwdriver for opening the side lid to check the oil level, a socket wrench to tighten or release the holder…
A Mount with screw holes for the Odoga SGR-NX3012SK-3 Inverter. The 2 Plates use the screws, that are already in the Inverter. Just unscrew them and screw them back in with the mounting plates in between. This was designed specifically…
This model is pushed onto the rectangular-ish valve of a GSI Pinnacle 4 Season stove to be able to keep the canister upside-down for liquid feed to the stove. Since this GSI stove has a generator tube, which goes through the flame, you…
Simple 2-part housing for step down voltage converter LM2596. For high currents additional radiator and vent may be required LM2596:…
Designed to hold my favorite brand of mustard: French's Dijon which is almost identical in taste to the good stuff Costco uses on their hot dogs. The cap is pointy and it takes forever to get the stuff out so I made this silly thing.
Deye 8K Hybrid Inverter improved FAN holder for SUN-8K-SG05LP1-EU to fit 3 92mm FANs instead of the original loud ones. v1 - original version v2 - slightly improved version, also has a multipart version to print on a smaller printer
I had to remove universal socket from my inverter so i made this thing to fill this sad emptiness with it. (But i can't do anything to fill emptiness in my heart) Part 2 can be printed for desirable height if you have shorter screws. Or…
Bracket for hanging the inverter linked below on the back of a Ryobi 48v Mower, turning it into a mobile power station! Print with decent levels of infill and mount with the hardware included with the inverter.…
I designed this in TinkerCAD to mount the LCD remote of my Fit4less 1000W pure sine wave inverter (bought on Amazon) without cutting a hole in the panel. This is the first thing I ever designed and made for 3D printing, and it works…
I made this new air filter assembly since the original required you to unscrew a bracket every time you wished to clean the filters and as you might imagine these things are often located in cellars or other dusty compartments and as such…
Inverter used https://www.aliexpress.com/item/1005004942381316.html Socket used: https://www.kvelektro.cz/zasuvka-vestavna-bals-71118-230v-ip54-s-vickem-modra-p1253624
Summary Above the workbench under the overhead shelves I had some runs of LED ribbon tape that provided great lighting, the problem was the unsupported wiring (could be snagged and pulled out) with several plug-packs required for running…
Flip your honey bear upside down to get more honey out of it :) Enjoy !!
A simple bracket to hold an inverter. 1.4" thick by 4" long and using #6 stainless screws. Print vertical, no supports needed.
![Kia - Hyundai [Inverter] Coolant Reservoir Cap SST](https://media.printables.com/media/prints/dae39b14-66f0-4909-a851-ae2ce6176e76/images/13686907_1bda379a-51d0-4470-9685-350cd7129102_920817b0-3c27-43f1-94b9-afe2a22249aa/cap_inside.jpg)
