81 models
This is a simple mount to attach the KUSBA USB accelerometer to a 3d printer bed up to 7 mm thick. All you need is a few M3 screws and one nut. Check out my universal hot-end mount
Mount to hold the KUSBA ( Klipper USB Accelerometer ) board and is compatible with the Elegoo Neptune 4 Pro. It's designed to insert two M3 nuts during printing for the 5mm screws that hold the PCB to the mount and it attaches to the back…
Mount your Kusba ADXL345 USB accelerometer quickly on probably any toolhead directly to your nozzle to get most accurate readings BOM (I used for my build) M3 20mm x 2 M3 6mm x 2 standard 5mm Threaded Heat Set Inserts x 4 Please let me…
a nearly universal mount for a KUSBA accelerometer some times mounting the board hanging off the end is necessary for the usb cable to clear the umbilical note: the hole pattern is different to the adxl345 uses a screw to clamp to the…
Mount for the KUSBA Input Shaper working with all Ender S1 Models. There are two mounts: One which is mounted on the extruder. You'll need to temporarily remove the M3x6 screw and use a M3x10. (see pictures) One which is mounted on the…
This is a simple mount to attach the KUSBA Usb accelerometer to almost any 3d printer. All you need is a few M3 screws. Please note that this is only used to run input shaping and then should be taken off so that your heatsink gets proper…
A mount for using the Klipper USB Accelerometer ( KUSBA ) with the Elegoo Neptune 3 Pro Printer (Plus / Max are also likely to fit but were not tested). You will need three M3 .8 screws with matching hex nuts to attach the KUSBA to the…
I designed some mounts for kusba adxl345 usb pcb by maker panda for my Elegoo Neptune 3 Pro. For klipper resonance compensation/measuring: https://www.klipper3d.org/Measuring_Resonances.html Link to a good (german) documentation:…
A mount for using the Klipper USB Accelerometer ( KUSBA ) with the Elegoo Neptune 3 Pro Printer (Plus / Max are also likely to fit but were not tested). You will need two 20mm M3 screws to attach to the extruder and two .8 M3 screws with…
Wanted to test bed frequency using KUSBA adxl345, tried a few ideas and ended up on this. 24mm hole spacing m3x6 screws x2 Print settings: -no brim or skirt -.52 wide first layer -1.1 first layer flow to ensure its stuck on. For neptune…
Conveniently run resonance testing for Klipper input shaping without having to change mounts. This mount clips on the top of the extruder for X-axis measurement, or clamps onto the bed for Y-Axis measurement. Designed to print without…
I don't have M3 Heated inserts so I modified the holes to be threaded M3 holes. Can secure the KUSBA in with M3x4 screws such as https://www.amazon.ca/gp/product/B0B3J35JSS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1. The original…
Use original printing instructions 14-03-2024: fixed hole spacing, was 23mm, changed to correct 23.5mm
Uses 2 m3 heat-set inserts or 2 m3 nuts. This is still a work in progress. Any advice on any changes to the design and any remixes would be appreciated. IF you would like to support me:…
This is a remix of the Rat Rig V-Minion Bed WAGO mount by Squirrelbrain with a mounting option for the KUSBA USB Accelerometer (ADXL345) for Klipper . I recreated it from scratch using measurements from Squirrelbain's STL as accurately as…
A simple mount for a Kusba accelerometer to mount to the buttom two screws on the Voron Afterburner toolhead. **updated to make the holes for heatsets slightly larger. ** Use 2 M3x5x4 heatset inserts (Voron BOM spec). Use 2 M3x6 BHSC to…
The mount gets screwed into the print head by temporarily removing the 2 screws on the right with 2 M3x7mm bolts. The kusba is mounted with 2 M3x6mm bolts. The holes to mount the kusba are designed to be threaded with the bolt as its…
Bed mount for KUSBA v2 accelerometer to for my V-minion, but should fit any bed. I used the following hardware for this: 2 M3 nuts and 2 M3x8 screws 2 Heat inserts m3x4x5 2 M3x6 screws KUSBA GitHub: https://github.com/xbst/KUSBA
This is a simple remix that maintains the print orientation and strength of the original but for the KUSBA v2. This bed clamp allows you to temporarily mount the KUSBA v2 without damaging your bed. Bill of Materials: 4x - M3 Short…
Print in ABS, ASA or PETG if you are enclosing the printer to avoid the plastic deforming. Easy to print with no need for supports or heat-set inserts. The lid will keep dust away and it also has standoffs that will press the…
This is a remix of Koop's design of the Mount for the Klipper USB Accelerometer board compatible with MicroSwiss NG extruder. As the original, this remix is compatible with KUSBA v2.3 and v2.4. I changed the design to insert M3 nuts…
I've pre-oriented the parts for their optimal orientation without supports. KUSBA mounts at the top where the threaded inserts are with 2 m3 screws. Uses the same bottom if you already have that printed Use the default The 100 print…
This is a very sturdy mount for the KUSBA 2.4 accelerometer for the prusa mk3s+, to help tune input shaping with klipper. Requires you to heat insert 2 standard M3 nuts. Until they are just flush with the surface, can be done with a…
This is a remix of the model from @Karagoal, only change is I added M3 threads instead of holes for threaded inserts.
A quick mount to attach the KUSBA ADXL to an H2 extruder. There is also an 80mm print with mounting holes for the KUSBA that should fit between binder klips on a bed slinger. -Added an offset mount for cases where the part cooling fan may…
This is one of my first designs so any feedback is welcomed! I made this mount to hold the KUSBA on my Dragon Burner toolhead for V0.2. I printed it in ABS 0.2 mm layer height with no supports. (I expect any filament would work)…
merging together a bunch of print heads to get all the features I wanted here is a list of what I want from this print head kubsa mount 3x 5015 fans beacon mount threaded inserts Update Aug 7, FINALLY actually printed this. I used: 6x m3…
The easiest and best way to mount an accelerometer to your E3D REVO hotend. Designed to mount a KUSBA or standard ADXL345 Accelerometer board to your E3D REVO hotend. There are two models: 1) Standard M3x12 screws and M3 nuts . 2) M3…
Hey, This is very simple adapter for Biqu H2 (V2) extruder to mount KUSBA 2 on top of it. I've printed in PETG with 50% infill, but any other material should be fine as well. 2x - M3 8mm screws to mount adapter to extruder 2x - M3 4mm (or…
Can be that you need to scale it down to 10% Just drafted out a Mount for the Kusba to my Anycubic Vyper. Fits to the Printbed and Printhead. Should also fit other Anycubic Printers. Widest holes fit the Printbed. Narrow holes fit the…
Well-fitting mounting cage for the genuine E3D Titan Aero Extruder on an Anycubic Kobra. It also has 2 mounting holes for a KUSBA PCB (maybe also suitable for ADXL345 PCB. Works with all stepper motors including the stock Anycubic Kobra…
KUSBA V2 USB Accelerometer STL File for Klipper- I downloaded the CAD file and converted it to a STL file so that I can design my own custom mount for my Delta Kossel printer. Hole diameter: 3.4mm Hole spacing: 23.5mm If you like my…
This mount replace the part cooling fan.
Mount for KUSBA (V2) adxl on BIQU H2 and Bed Slinger https://github.com/xbst/KUSBA KUSBA - “Klipper USB Accelerometer” A PCB designed to make Klipper's input shaping much easier by simplifying the wiring and config for measuring…
Kusba Accelerometer mount designed for the Satsana Dual 5015 Fan Duct. Very simple print, extremely sturdy with locating pins. Supports 4010 fans and 4020 fans. Simply unscrew the two top screws for your fan and put the two locating pins…
This magnetic mount will allow you to measure any axis from any point without a printer specific mounting solution. This is designed specifically for the KUSBA adxl345 accelerometer. You will need to pause your print before the hollow…
This print allows for resonance compensation tuning using the KUSBA on the Creality Ender-3 S1 with large cooling mods such as the Taurus V5 installed. You will also need: 2x M3x8 screws (replaces the stock M3x5 screws; holes are not…
KUSBA and Fysetc Accelerometer mounts for Mosquito hot ends , mount directly to the 25mm fan
A basic mount for the Input shaper KUSBA designed by Isik et al. This mount is for Eva carriage 3.0 have not tested on Eva 2. Requires: 4 M3x8 bolts Printed in ABS if printed is enclosed or prints with high temperature but can be printed…
I based my design on the original, but I remodeled it completely in freecad, I am attaching the freecad and STLs (you can make fun of my modelling, I am still learning!) I also included a STL to create a couple of plastic washers you can…
This is a mount to measure the X-axis resonance of a Sovol SV-06 with a KUSBA V2 accelerometer. You will need longer M3 screws than the factory screws to mount this. I used 10mm countersink screws. This mount does not clear the Z-axis…
A mount to hold the Klipper USB Accelerometer (KUSBA) to the fan shroud of the Ender 3. The KUSBA mounts to the... mount via two M3 nuts (place for them on the inside) and M3*5 bolts, and the mount itself friction fits to the fan shroud…
I made this to quickly mount a KUSBA to the side of my extruder using the same holes as my 5015 cooling fan. This uses M3 threaded inserts for the board mounting. Some of the 5015 fans vary a bit with the hole to hole distance. This works…
This is a simple mount to attach the KUSBA USB accelerometer to a 3d printer bed up to 7 mm thick. All you need is two M2 screws to mount the KUSBA, a long M3 screw and one M3 nut.
Magnetically attach either a KUSBA USB-C or BigTreeTech USB-C ADXL345 accelerometer to your bed slinger using eight 10mm neodymium magnets. Push magnets in using the back end of a sharpie marker. The magnets can help you store the device…
I designed this simple KUSBA Accelerometer holder for @hangloose y-axis linear rail mod from here: https://www.printables.com/de/model/372792-anycubic-vyper-y-axis-linear-rail-mgn12h Just replace two screws from the mentioned mod with…
Kusba v2.4 accelerometer mount used to mount on a Nema 17 motor. I used it to mount on the pancake Nema motor that's part of the Bondtech DDX v3 for the Creality CR-10s Pro printer. This is a nice and solid mount that should work well for…
This is an X axis mount for the KUSBA accelerometer for a SOVOL SV06+ printer. It goes right on the front of the extruder right above the filament advance wheel. Simply remove the top two screws and replace them with ones a bit longer.…
KUSBA mount, for use on printers making use of Detlef01's Titan conversion . Mounts to the inserts for the highlighted redundant “endstop” component
You can print with support in the “windows” that I opened, or not, depends on your bridging capabilities :) Same print settings as the original.
Attach the KUSBA USB-C or BigTreeTech USB-C ADXL345 accelerometer to the bed holder using twelve (Maximum, you can try using less, say eight, but I'm not sure about the result.) 8 x 3 mm neodymium magnets. Adhere them with adhesive,…
Remix for PrimaCreator PEI-plate with narrower placed holes than Eleegos. (The holes are 3,46mm closer to each other.)
I had enough to have an ADXL345 with a Raspberry Pico hanging around so i bought a Kusba. In my case i printed it in PLA+ but being so close to heated parts PETG or ABS would be ways better (i still have to test the one i printed in PLA…
This model is specifically designed to securely hold the KUSBA V2 on The 100 DIY printer toolhead. It ensures stable and precise positioning, enhancing the toolhead's overall performance and usability. There are two versions: one for M3…
Simple plate for mounting the KUSBA Klipper USB Accelerometer (v2) I designed it to be attached to other mounting stuff I was designing; this was originally a common component that attached to things that would attach to the bed for Y…
KUSBA is 23.5 mm c-c hole mount, this is a remix for the larger profile
— WARNING: DO NOT PRINT OR HEAT THE NOZZLE WHILE THIS MOUNT IS IN PLACE — You need to take out the hotend cooling fan, so you can install this mount. Which means that if you heat up the nozzle, the heat might creep up to components that…
Printed in White PETG at 0.2mm layer height with no supports.
The kusba is mounted with 2 M3x6mm bolts. The holes to mount the kusba are designed to be threaded with the bolt as its being screwed in. I found best results with the simple bed mount were it lying upside down, and putting support…
This magnetic mount will allow you to measure any axis from any point without a printer specific mounting solution. This is designed specifically for the KUSBA adxl345 accelerometer. You will need to pause your print before the hollow…
A simple adapter to mount a KUSBA ADXL on a Mellow Nozzle Mount. You need 2x M3 screws and 2xM3 nuts. I used M3x8
Can now mount a Kusba accelerometer to the adapter and no longer have to mount/unmount ever again :) Just plug in a USB
The kusba is mounted with 2 M3x6mm bolts. The holes to mount the kusba are designed to be threaded with the bolt as its being screwed in. I found best results with the simple bed mount were it lying upside down, and putting support…
I tried my best to find a mount that would let me use two screws to secure his ADXL board. But due to the odd hole pattern, it was hard to find anything beyond an extruder mount or afterburner. So i was using just 1 screw. However this…
AnyCubic Kobra KUSBA Extruder Mount remix Thanks to the original designer, I made a quick remix to fit my needs. Remixed to increase the thickness of the plate where the KUSBA mounts in order to allow for use of M3 8mm screws to mount the…
I used the mount hole locations from the "KUSBA mount for spite" and used the mount holes from the "adxl343 mount for microswiss" for the location on the NG extruder. Can be either used as a press fit as it holds quite well or use a 12mm…
Hello! Since I didnt find a mount for the ADXL345 from Kusba, I made one myself. I'm new to 3d printing and especially CAD but I tested the mount and it works. It is designed to hold the Kusba with double sided tape, it fits snug and…
this will allow you to easily swap between measuring the bed and print head to use this model you need a 15x8mm neodym magnet and 2 self threading screws pause the print and insert magnet
print flat no supports required unless you want mounting machine screws are M3*8 with a nut on the back seems to fit perfect mounting to the extruder head are 2x m3*16
Mount to attach kusba adxl accelerometer to flsun v400 when using the fan shroud for the BigtreeTech Knomi screen. I plan on leaving my accelerometer install permanently. 3mf file is attached feel free to do whatever you like. I printed…
I did not search exhaustively, but what I found was a nicely designed mount, but it was situated on the rear of the X Axis carriage and because of it's position X could not be homed while it was installed. I designed this so I can just…
KUSBA V2 USB Accelerometer cover . name is self explanatory . didn't like that the KUSBA didn't have a cover . looked everywhere couldn't find one so did some thinking and this is the result
Kusba accelletometer mounting bracket on extruder. Use the two screws as the cap are used To setup in neptune pro you can follow this https://www.printsleo3d.com/new-page or check https://github.com/xbst/KUSBA
Dimensioned on the official model of the KUSBA V2 from the KUSBA github (user xbst) This isn't modeled line-to-line but it is a tight fit and may need some modification depending on how well your printer is calibrated. I had a great fit…
My remix for the very nice looking KUSBA mount by @PhilippSchmid_897996. Needs three M3 bolts with matching nuts.
Designed for use with OrzOrzOrz's Neptune 4 Shroud with KUBSA spacing. This adapter allows you to easily mount a Bowden tube coupler to your extruder. It is designed to prioritize strength, ensure clearance for the indicator wheel, and…
This model can be used to mount the KUSBA v2 on top of the Creality Sprite extruder. Sink a pair of M3 brass inserts into the top holes to mount the KUSBA, and run a pair of M3x12 screws into the side mounts. This is a remix of an…
the grey version is the one posted here v3 coming soon as I am still not happy with the amount of flex simple bowden mounting point using the KUBSA mount on the printhead, I am currently printing this version, I have printed a v1 before…
Mount for kusba accelerometer that mounts it to sprite extruder hotend. Required hardware: 1x M3x8 4x M3x12 Some M4 nuts
A simple mount to attach the kusba pro to the bed. Screw holes fit the supplied screws from the nozzle mount, but the fit is tight enough without them. Just print, insert the kusba pro and do your y-axis calibration.
