Counting matching models…
This model is a remix from Maple Leaf Makers and the excellent V0 chamber thermistor mount. Just adapted to the 2020 extrusions fitted for the Voron 2.4/Trident . BOM 1x M3x8mm BHCS/SHCS 1x M3 T-Nut 1x 3x15mm thermistor
V0 Chamber Thermistor Mount A mount for a standard 3x15mm cartridge thermistor on 1515 T-Slot Extrusion Designed for the Voron V0 BOM 1x M3x8mm BHCS 1x M3 Nut 1x 3x15mm thermistor The most up-to-date version of this mod can always be…
This is a fix to a problem you didn't realize you had! *****PLEASE READ THE FOLLOWING BELOW. THIS GOES INTO FURTHER DETAIL AS TO WHY THIS PART IS IMPORTANT/USEFUL***** The K1 Series printers chamber thermistor is in a direct path to where…
Dobrý den, Mám pro vás medajle pro 3 prvni místa. 1st, 2st a 3st. Jsou vytvorene podle napadu z inernetu. Jsou velmi povedene. Tisknuto bez podpor! Pokud vás moje práce zaujala, odkazy jsou zde: https://www.instagram.com/ainon3dprint/…
I chance the mount from HenryA a little bit to fit on my v0.2 with the 1515 extrusions and a 3mm thermistor the Thermistor fits very good on my print. if yours to tight you can open the hole a bit with a drill bit
The centauri carbon has a chamber thermistor that is mounted to the frame with a steel screw and plastic spacer. The steel screw is thermally conductive enough to significantly skew chamber temperatures colder. I found that the built in…
A remix of my solid plate , for those who want to keep the rear exhaust housing in place. STEP file provided if you want to make any changes.
Just a modification of the original Voron Z-Chain Guide to attach an additional chamber thermistor to your gantry. The thermistor (e.g. a glass bead thermistor) is positioned inside the Z-guide and held in place with a small zip tie or…
Tool for remove the XH 2pin connector nozzle heater of centauri carbon Updated (16Feb26): Added New puller for ZH 2pin with printed spring. Updated (15Jan26): Added New puller for XH 2pin with printed spring. This version prevents the…
Are you looking for a simple enclosure to hide your PCB? You've found one! Assembly is pretty straightforward, here's what you need: 1x Top cover (print) 1x Bottom cover (print) 3x Button (print) 4x M3x10 bolt (you can optionally use…
This mount holds a small thermistor to to capture chamber temperatures for an enclosed printer. This is used on any printer that uses a 2020 extrusion. Printed with ABS Infill: 40%
This holds a 5mm thermistor ( example ) to a 2020 extrusion, for Voron or other 2020 frame printers. BOM 5mm thermistor (1) M3 6mm cap head screw (1) 2020 extrusion nut of your choice CAD [ Link ] Thermistor diameter is parameterized
Thermistor mount that clip directly on 3030 extrusion frame of your printer/enclosure allowing monitoring of inside temp. Compatible with cylindrical thermistor with diameter of 3 mm Code example for using with Klipper on a BTT Octopus…
Standard Voron 2.4 Z Chain Guide extended with thermistor (cylindrical type, 10mm x 3mm) mount. Thermistor is used as chamber thermistor. Thermistor secured with M2x5mm (BHCS would be best). Along with chamber fan:…
This is a modified version of Jeoje's Voron V2.4 Z Chain Guide with Integrated Thermistor Mount . This Z chain mount allows you to install a standard 3mm thermistor to monitor chamber temperatures. Jeoje's original was designed for the…
Hello, this is my first model. Didn't like idea to use metal M3 screw (and I don't have one) so I created some kind of retainer from plastic instead. Works with original model (attached into my STL, all credits to Robert Samples), snaps…
I updated my V0.1 to the new V0.2 bottom Z endstop and had an unsightly hole in my back panel where the switch used to pass through. I decided to remix samwiseg0's NTC100K thermistor mount to fit in that space and cover the hole while…
Hello! If you've got a COREBOXX or similar MMU setup, your PTFE tube from the MMU selector to the nozzle may be pushing against the chamber thermistor. I'm afraid this could cause problems over time, so I did a quick search for a…
For any thermistor with 3 mm diameter cartridge. Assembly: Print it Cut out the thin section acting as a support (circled in one of the images) Get thermistor wire through newly created crevice Pull the wire further so that thermistor…
A little box for my hotends for the Kobra S1. The lettering on the lid and the base is made with an modifier. Feel free
This mount holds a small thermistor to to capture chamber temperatures for an enclosed printer. This is used on a Voron V0, but it will fit on any 1515 extrusion Printed with ABS Infill: 40%
A simple mount for a chamber thermistor, and attaches to a 2020 frame using an M3 x 6 SHCS with a M3 T-Nut. The You can use a small zip tie to prevent any movement while the machine is running, but the thermistor should be friction fitted…
I've gotten tired of gothic terrain and wanted something different. I'm using for Battletech but ruleset agnostic. I'll continue to put more models out in the line. Prints fine without any supports. Prints as one file or split into two…
Had a pile of these thermistors sitting around in my drawer from my old ender and decided to repurpose them as a chamber temperature sensor for my Voron 2.4 Designed to fit on any 2020 extrusion and includes a raised section on the bottom…
I used an old thermistor from an ender3 hotend and added following into Klipper / printer.cfg: [temperature_sensor chamber] sensor_type: EPCOS 100K B57560G104F sensor_pin: PF5 min_temp: 10 max_temp: 80
I've gotten tired of gothic terrain and wanted something different. Going for Art Deco retro futurism vibe. I'm using for Battletech but ruleset agnostic. I'll continue to put more models out in the line. Prints fine without any supports.…
A remix of Liselotte111's hexagon door cover with an added 3mm thermistor clip for the chamber temperature.
I've gotten tired of gothic terrain and wanted something different. A little Art Deco influence. I'll continue to put more models out in the line. Prints fine without any supports. Prints as one file or split into two pieces with…
This is a replacement silicone cover for the original E3D V6 (new version). The original cover does not stay in place. Just print all 3 parts, connect them and mold your cover. Instructions: Print everything with about 20%-25% infill. You…
Silicone mold for making silicone tube heatbed thermistor
This is a clip-on thermistor mount for a Voron chamber designed for 2020 aluminum extrusion . Suited for thermistors with 3mm diameter. Unlike the original mount, this version clips directly onto the extrusion and does not require screws,…
I wanted to mount my chamber thermistor at the top rear of the build space of my Voron V2. I also installed a CAN Bus toolhead with an umbilical cable, as well as a Nevermore Micro Duo V5, and removed the rear exhaust fan. This exhaust…
This is a modified cable cover that allows you to mount the chamber thermistor for the LDO tool head PCB to the cable cover of the Galileo 2 extruder on your Stealthburner tool head. This is a remix of both the LDO Nighthawk cable cover…
The Core One Printhead Left Cover with cutouts for access to the heater and thermistor connectors. There is a compromise I made between the ease of removing the connections, printability, and still functioning as protection of the rest of…
Just a remixed model with a ZeroG logo instead of Voron
I redesigned the chamber thermistor mount to have the thermistor and wire outputs be opposite instead of at a right angle to each other. This is better for my use case, as it allows me to mount it on the bottom back extrusion of my Voron…
For mounting a chamber thermistor on the gantry, but this time with the Voron logo the right side up. Includes the Fusion file so you can change the thermistor size for you liking. To do so, change the ThermistorSize parameter.
Printed with ASA 0.2 layer in app. 25 minutes on the K1 Max
Remix of Umbilical Z for Voron 2.4 with support for a chamber thermistor
This mounts the short chamber thermistor included in the Formbot Voron 2.4 kits by its JST connector to a 2020 extrusion. Add an M3 hammer-head T-nut, and use an M3x8mm bolt to secure it. I wanted a clean way to mount the chamber…
I liked the original model so much, but found out the thermistor I had was 5mm in diameter, and it did not fit. This larger box lets you hide the zip tie better and does not hurt even if your thermistor is tiny – there is plenty of space…
Here is a PT100/PT1000 thermistor mount for an Ender 3 NG v1.2! It is designed to have a look similar to the Ender 3 NG v1.2's original parts. There's a cable tunnel on the back that gently holds the thermistor in-place with its own…
A little box for my nozzles for the Kobra S1 with upgraded hotend. The lettering on the lid and the base is made with an modifier. Feel free to do your own or use mine within the *.3mf-File
This mount for an extrusion keep wires and thermistors in place. I made it long enough to have some strain relief, though I do include a shortened version handy for tight spaces. The models are designed for LD0 2020, Misumi 1515, or…
It fits perfectly with the 3 mm diameter thermistor. It can be used with this mod: https://www.printables.com/model/960049-modular-cable-management-clips-for-2020-extrusions
A compact and elegant Voron chamber 4mm thermistor mount
Adapterplate to fix the DS18B20 one-wire thermistor inside the chamber of a Voron V0. The adapter will be screwed on top of the z-rail extrusions, the wire will be routed through the hole on the right side of umbilical PCB. The thermistor…
For use with a PTC chamber heater module. Mounts to the right panel using the stock mounting points. You will probably need longer m3 screws. The termistor mount replaces the the plastic spacer the CC's chamber temperature sensor is…
A simple bracket to mount a 5x30mm thermistor cartridge to a 2020 extrusion. The thermistor is held by a slight press fit. Hardware you need: 1x M3x8mm Socket Head Cap Screw 1x M3 T-Nut/Roll-In-Nut 2x Cable Tie 2022-12-03: Added a 3mm…
From screw mount to 1cm VHB tape mount
Modified both main body and cable cover to provide access to the thermistor header
remixed to have a slightly thicker part where the thermistor clicks in and out as i found the original broke so easily
Thermistor mount that clip directly on 2020 extrusion frame of your printer/enclosure allowing monitoring of inside temp
What is this? This mod adds the following small quality of life improvements to any Voron Switchwire (or really any 3030 based printer): Rigidly mounted Z endstop away from the bed Chamber thermistor mount point away from heat generating…
Hi, this is the Chamber Thermistor holder I use on my own LDO Rev. C Voron 2.4r2. I didn't like to see the Chamber thermistor the way the LDO holder attaches, so I designed this from the LDO .f3d file, and like how it works much better.…
We use thermistor from old E3D V6 hotend. Klipper config is : [temperature_fan chamber] pin: PD13 max_power: 1.0 shutdown_speed: 0.0 kick_start_time: 5.0 cycle_time:0.01 off_below:0.1 sensor_type: NTC 100K beta 3950 sensor_pin: PF5…
5mm chamber thermistor mount you will need to print this in something that can handle your expected chamber temps, i chose ABS. parts needed thermistor m3 x8 socket or button head screw m3 t-nut
Need some simple frame mounts for chamber thermistors based around 3mm thermistors that most people use for chambers. Made versions for both 1515 and 2020 based frames. I've provided the or
BOM: SHCM3x30mm [1x] M3 Voron heat-set insert [1x] Compatibility: Voron ClockWork2 Extruder; CW2 style mounts for other extruders, as long as they feature the mounting hole previosuly used to engage the latch. Warning: the ring notch on…
If you enjoy this model, please give it a like! This took ages to get right, and I hope to put this kind of effort into more parts. 2020 Extrusion clip with a 3mm diameter thermistor holder. No hardware needed at all, just push in and it…
Print with 0.2 or 0.25 layers, typically ABS or ASA for RatRig users. Use a small zip tie to hold the thermistor in position. The glass bead should be held flush to the surface or slightly below, so it gets good exposure to air, but is…
A modified version of Jeoje's Z chain guide with integrated thermistor (side-) mount for Voron v2.4 printers.
Die Originalstopfen sind nach dem Hochdruckreinigen schnell mal verschwunden. Ich habe die Ersatzteile in TPU95a gedruckt The original plugs disappeared after high-pressure cleaning. I printed the replacement parts in TPU95a
I really like my MISTO refillable vegetable oil spray bottle, but the inside part that held the plunger broke, so it wouldn't pump anymore. I modeled a new cap that holds the plunger in place more securely. Printed on Prusa Mini+ with a…
Thermistor holder, which was created for 3030. With it you can measure e.g. the housing temperature. I Use this 100k Sensor: https://de.aliexpress.com/item/4001345867305.html Add this to the printer.cfg: [thermistor chamber_temp]…
The Galileo version of the Nitehawk cable door, so you can mount the chamber thermistor above the toolhead. Credits to JaredC01 (Galileo) and MotorDynamicsLab
Update 2025-12-11: Added a version that just snaps into place. No unscrewing of the screws needed and cannot come loose since it's locked by the screw heads. I think the idea of a protector for the flimsy thermistor is brilliant, but…
I'm using a thermistor from an old printer for a chamber sensor. I remodeled Triano's mount to accept a smaill zip tie to hold it in place.
This remix will fit 5mm diameter Thermistor sensor, and you could easy modify the hole in the step file to fit your sensor.
See description from Original creator: https://www.printables.com/model/618488-stop-it-z-endstop-chamber-thermistor-mount-for-vor
I accidentaly bought the wrong thermistor and didn't want to buy another one, so I found the original model by @MapleLeafMakers and thank god they've left the step file. So I quickly adjusted it for the 3950 100K thermistor. This is a…
Pug Gantry Mount Remix: Toolhead Umbilical & Thermistor Option Overview This project is a functional remix of the Pug Gantry Mount (Upper) . It was developed to provide a clean, integrated solution for users transitioning from traditional…
Assembly: - Cut the breakout board. (distance between holes for screw is 9x2,54mm) - Solder two JST-XH connectors to the universal PCB and make connection between pins - Add M2,5 thermal inserts to the mount - Mount the board with two…
Remixed (rebuilt) Voron 2.4 z-chain relocation mod w/thermistor mount from 2-hole IGUS to 3-hole generic chain mount.
Mounts to 4040 extrusion using M4 bolts and T nuts. I used countersunk bolts for a flush finish. Print in PETG / ABS / ASA or any high(er) temperature filament. Built and available on OnShape if you need to make adjustments.
Removed the gap for the thermistor connection.
Printed with same standard voron settings. This remix is for those who did an LDO build and the original cover doesnt fit, so this got remixed to make it work proper. original credit goes to @MaxDolski_1033657 Thanks and hope this helps…
This is an improved (out of necessity) version of my own MK3 style heatbed cover for the Prusa Mini. It still features: MK3 style; Allows for heatbed connectors on top for optimal current flow; Reliefs the cable and helps prevents…
I had some glass thermistors lying around and want to use one for my Voron0 as chamber thermistor. I had a look at the 2020 Mount from Nikholas Pcenicni and took his model as reference for my own design. I'm aware, that the Openscad file…
These sensors are not very robust. Protect it! PLEASE be careful when inserting this model into the fan grill. It's designed to snap in. Insert the bottom edge first and then rotate the part up to insert the top edge while gently wiggling…
When building the Voron Trident I realized that the heatbed is partially permantly connected. Heatbed power is connected with the WAGO junctions, the Z-stop switch is connected by a JST connector but the heatbed thermistor was permanently…
Simple enclosure for a generic 3950 thermistor (the ones with the glass bead). Can be used to mount to 2020 aluminum extrusions. Additional Hardware needed: 1x M3x8 SHCS 1x M3 Hammer (T) Nut
I wanted a single bracket to hold a camera and a chamber thermistor, along with the camera being on the right side - closer to the Pi. Camera is set pointing down at 10 degrees for best visibility. Use M2x8 (or shorter) self tapping for…
Thémistocle – Buste Français Inspiré de la représentation la plus célèbre de Thémistocle, ce buste imprimable en 3D rend hommage à l’un des plus grands stratèges de la Grèce antique. Homme d’État et général athénien du Ve siècle avant…
Klipper Expander Cover with clearance for the Thermistor terminations as to prevent pinching the connectors when in closed. this print is really dependent on tollerances so can recemend you slightly scale down the model as i have found it…
⚠ Your Z extrusions must be threaded on the top! ⚠ This mod requires a new back plate with holes for the wires! (Printer specific, there are tons of options online. Print as needed.) Please check the → GitHub page ← for more information…
This is a twist-in 3030 extrusion mount for the Thermistor found inside the Sunlu S4 Dehumidifier. The mount uses the screws that held the thermistor in place inside of the S4 unity.
This PTC heater holder will help you mount it to the top of the 4020 aluminium extrusion. With the 45 degree rotation the enclosure panels won't choke the heater fan. Also there is a thermistor holder. With this you can monitor the air…
This is my first ever model and I don't know what I'm doing. Remix of JaredC01's Galileo2 Extruder cable cover with the thermistor mount from LDO's CW2 cable cover. Print with Voron settings. Material ABS/ASA Layer Height 0.2mm Extrusion…
Although it is just fine for the extruder motor in direct drive to run hot, it will, thats what it does. The problem is that the HGX Lite extruder (all metal) is a great heatsink for the motor, so it gets very hot too. When it is hot…
A mount for a 4mm diameter Thermistor Made in Tinkercad
Lets you clip a 5 or 3 mm diameter tube chamber thermistor on your printer's 1515 extrusion frame
➡➡Add the SimpleAF logo to the backdrop of your printer. ⬅⬅ Model Options Single Color Color Swap Multi Color Filament Requirements PETG ABS ASA ⬅ preferred Colorized Model Import Instructions Step 1: Step 2: Step 3: Step 4: .3mf files…
The original E3D V6 thermistor catridge is equipt with a Molex Micro-Fit 3.0 connector close to the cartridge. Together with the E3D High Precision Heater Cartridge , which has the same connector, it is possible to swap the hotend without…
This was made to accomodate a Frame thermistor or running other cables through the skirt and along the Z extrusion for maybe a Chamber Thermistor or whatever else you want to route there. As you can see from the pictures, I used it to…
The mount is attached with double-sided adhesive tape
Z Umbilical mount with PUG (Printed Universal Gland) and Thermistor mount on the gantry
It is flash with mounting surface. In case that surface is not flat you can heat edges and make them curve according to curvature of mounted surface for tighter fit and nicer look. Support me: Monero address:…
